双包层光纤侧面耦合器

研究了一种侧面抽运双包层光纤的方法，从被剥除了外包层、端面为350μm×400μm的D型双包层光纤内包层上切下长度为3mm的一段柱体，并胶合在相同的双包层光纤内包层的侧面上，构成了柱体-光纤侧面耦合器。半导体激光器的抽运光从该柱体的一端入射并通过它耦合进入双包层光纤的内包层，实验测得耦合器最大耦合效率为85％。该方法适用于输出功率为数瓦的光纤激光器和放大器的侧面抽运。

微棱镜与双包层光纤侧面耦合效率的实验研究

对微棱镜与双包层光纤侧面耦合技术进行了研究。用光学胶把尺寸为1mm×1mm×1mm直角棱镜的直角面胶合在尺寸为330μm×170μm的内包层侧平面上，激光束以一定的角度从微棱镜的另一直角面入射并通过它耦合进入双包层光纤的内包层，实验测得耦合效率为86％。该方法可用于双包层光纤的侧面抽运。

高功率脉冲双包层光纤激光器的新进展

对高功率脉冲双包层光纤激光器的国内外研究进展进行评述，通过建立了小信号瞬态增益模型，对脉冲激光信号经过双包层光纤放大后的波形进行了数值模拟。分析了基于MOPA方式脉冲双包层光纤激光器的几个问题，报道了中科院上海光机所采用振荡-放大（MOPA）方法获得133．8W平均功率脉冲放大输出的实验结果。

两根掺镱大芯双包层光纤激光器获得113W同相输出功率

利用一个自成像共焦腔和一个空间滤波器实现了两掺Yb大芯光纤激光器的位相锁定。观测到稳定的具有高对比度的干涉条纹。相干条纹的对比度为59%，而非相干时对比度为6%。中心条纹的宽度与理论计算结果吻合得很好。对同相模式而言，位相锁定激光器阵列输出达到113W，对应的斜率效率为38.5%。

采用国产双包层光纤的声光调Q激光器

实验报道采用我国自行设计的大模场掺镱双包层光纤，利用简单声光调Q装置，成功实现调Q运转；在1－50kHz调制频率下获得了百纳秒的调Q脉冲，其输出光束质量因子大约为2。当重复频率为1kHz时，获得了脉冲宽度为132ns，能量0.93mJ。同时实验中观察到的调Q脉冲常出现一点锁模现象，针对这一现象进行了讨论。

光纤激光器及其相干组束

简述了光纤激光器的发展历史，重点介绍了双包层光纤激光器的进展并给出了高功率双包层光纤激光器的最新研究结果。评述了目前国内外高亮度激光的关键技术：光纤激光器的相干组束。介绍了几种典型的相干组束技术并分析了其工作原理。最后给出了相干组束研究的最新结果。

千瓦级双包层光纤激光器冷却方案设计理论和实验研究

尽管双包层光纤激光器的散热性能好于传统的固体激光器的散热性能,光纤激光器中的热沉积仍然是限制提高其输出功率的重要因素.以双端抽运的400W双包层光纤激光器为实例,定量分析了光纤内的热沉积分布.根据所建立的散热模型,为了确保千瓦级双包层光纤激光器安全稳定的运行,抽运端附近的对流换热系数应大于2.8×10-2W·cm-2K-1.据此设计出高功率双包层光纤激光器抽运端冷却装置并成功应用在激光系统中,获得了千瓦级的激光输出.

瓦级双包层光纤超荧光光源的实验研究

采用大功率半导体激光器抽运25m掺Yb双包层光纤，在单程装置中，前向(SPF)和后向(SPB)分别获得了1．46w和1．82w最大超荧光功率，斜度效率分别为23．4％0和29．2％，3dB带宽最大为11nm。采用特定范围波长双色镜作为前腔镜，形成双程前向(DPF)装置，获得最大超荧光输出功率2．12W，此时斜度效率为43．2％，中心波长在1070nm，输出光谱平坦性较好，3dB带宽从单程的11nm提高到42nm。

Passive Q-switched mode locking of double-clading Yb : fiber laser with ion-implanted GaAs

We report the technique of the ion-implanted semi-insulating GaAs wafer used for passive Q-switched mode locking in double-cladding Yb:fiber laser. The wafer was implanted with 400-keV energy, 10(16)/cm(2) dose As+ ions, and was annealed at 600degreesC for 20 min. At the pump power of 5W, we achieved output power of 200mW. The repetition rate of envelope of Q-switched mode locking is 50-kHz with a FWHM envelope of 4mus. The repetition rate of mode locked pulse train was found to be 15-MHz. This is the first report of such a kind of laser to the best of our knowledge.

Electromagnetic analysis of novel class of multiple core/multiple clad step index single mode optical fiber by analytical means

General propagation properties and universal curves are given for double clad single mode fibers with inner cladding index higher or lower than the outer cladding index, using the parameter: inner cladding/core radii ratio. Mode cut-off conditions are also examined for the cases. It is shown that dispersion properties largely differ from the single clad single mode fiber case, leading to large new possibilities for extension of single mode operation for large wavelength tange. Paper demonstrates that how substantially we can extend the single mode operation range by using the raised inner cladding fiber. Throughout we have applied our own computations technique to find out the eigenvalue for a given modes. Detail derivations with all trivial mathematics for eigenmode equation are derived for each case. Paper also demonstrates that there is not much use of using depressed inner cladding fiber. We have also concluded that using the large inner cladding/inner core radius we can significantly increase the single mode operation range for the large wavelength region. (C) 2015 Elsevier GmbH. All rights reserved.

Wavefront measurement of double-clad pulsed ytterbium fiber laser

Because of high efficiencies, compact structure, and excellent heat dissipation, high-power fiber lasers are extremely useful for applications such as cutting, welding, precision drilling, trimming, sensing, optical transmitter, material processing, micromachining, and so on. However, the wavefront of the double clad fiber laser doped with ytterbium is still unknown. In this paper, wavefront of a fiber laser is measured and the traditional Hartmann-shack wavefront sensing method is adopted. We measured a double clad fiber laser doped with ytterbium which produces pulse wave output at infrared wavelength. The wavefront shape and contour are reconstructed and the result shows that wavefront is slightly focused and not an ideal plane wavefront. Wavefront measurement of fiber laser will be useful to improving the lasers' performance and developing the coherent technique for its applications.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

Investigation on colloidal Te doped CdSe (CdSe:Te) quantum dots suspension in a liquid-core fiber

Here, we demonstrate the use of a colloidal CdSe:Te quantum dots suspension as active liquid-core in a specially designed optical element, based on a double-clad optical fiber structure. The liquid-core fiber was realized by filling the hollow core of a capillary and waveguiding of the core was ensured by using a liquid host that exhibits a larger refractive index than the cladding material of the capillary. Since the used capillary possessed a cladding waveguide structure, we obtained a liquid-core double-clad structure. To seal the liquid-core fiber and e.g. prevent the formation of bubbles, we developed a technique based on SMA connectors. The colloidal CdSe:Te quantum dots were excited by cladding-pumping using a pump laser at 532nm operating in the continuous-wave regime. We investigated the photoluminescence emitted from the colloidal CdSe:Te quantum dots suspension liquid-core and guided by the double-clad fiber structure. We observed a red shift of the (core) emission, that depends on the liquid-core fiber length and the pump power. This shift is due to the absorption of unexcited colloidal quantum dots and due to the waveguiding properties of the core. Here we report a core photoluminescence output power of 79.2μW (with an integrated brightness of ≈ 215.5 W/cm2sr ). Finally, we give an explanation, why lasing could not be observed in our experiments when setup as a liquid-core fiber cavity.

国产掺镱双包层光纤的激光特性

采用MCVD方法研发了掺镱双包层光纤，并对其结构特性、荧光特性和激光特性进行了测试和研究。其D形内包层尺寸为400／450μm，数值孔径为0．36，纤芯直径约为16μm，数值孔径约为0．18。荧光谱线的范围为1000-1140nm，1030nm处的峰宽大于50nm。采用大功率激光二极管单端泵浦6m长的双包层光纤，在泵浦人纤功率为61W时，获得了32W的激光输出，斜率效率为64％。该光纤在高功率处未发现饱和现象，通过优化光纤参数与泵浦方式还可以提高转化效率和输出功率。实验表明该光纤可以取代进口光纤用作高功率

133-W pulsed fiber amplifier with large-mode-area fiber

A master-oscillator fiber power amplifier (MOPA) system with a 4-m-long Yb3+-doped homemade large mode area (LMA) double-clad fiber is reported. The system emits up to 133.8 W of amplified radiation at a wavelength of 1064 nm and a repetition rate of 100 kHz, limited only by the available pump power. Peak power of 300 kW at 20 kHz with a pulse duration of 15 ns is obtained. (c) 2006 Society of Photo-Optical Instrumentation Engineers.