Hydrochemical variations and contaminant load in the Rio Tinto (Spain) during flood events

The aim of this work is to study the hydrochemical variations during flood events in the Rio Tinto, SW Spain. Three separate rainfall/flood events were monitored in October 2004 following the dry season. In general, concentrations markedly increased following the first event (Fe from 99 to 1130 mg/L; Q(max) = 0.78 m(3)/s) while dissolved loads peaked in the second event (Fe = 7.5 kg/s, Cu = 0.83 kg/s, Zn = 0.82 kg/s; Q(max) = 77 m(3)/s) and discharge in the third event (Q(max) = 127 m(3)/s). This pattern reflects a progressive depletion of metals and sulphate stored in the dry summer as soluble evaporitic salt minerals and concentrated pore fluids, with dilution by freshwater becoming increasingly dominant as the month progressed. Variations in relative concentrations were attributed to oxyhydroxysulphate Fe precipitation, to relative changes in the sources of acid mine drainage (e.g. salt minerals, mine tunnels, spoil heaps etc.) and to differences in the rainfall distributions along the catchment. The contaminant load carried by the river during October 2004 was enormous, totalling some 770 t of Fe, 420 t of Al, 100 t of Cu, 100 t of Zn and 71 t of Mn. This represents the largest recorded example of this flush-out process in an acid mine drainage setting. Approximately 1000 times more water and 1408 200 times more dissolved elements were carried by the river during October 2004 than during the dry, low-flow conditions of September 2004, highlighting the key role of flood Events in the annual pollutant transport budget of semi-arid and and systems and the need to monitor these events in detail in order to accurately quantify pollutant transport. (c) 2007 Elsevier B.V. All rights reserved.

Excitación vibracional de moléculas adsorbidas por fotoelectrones de muy baja energía

En esta Tesis Doctoral se demuestra, en primer lugar, la existencia de efectos catalíticos inducidos por láser en procesos de captura electrónica disociativa para las moléculas SF6, acrilonitrilo o 2-propenenitrilo (ACN) y CH3I adsorbidas en Ba y ACN adsorbida en Cu policristalino, detectándose como productos SF−5 y SF−6 para SF6/Ba, CN− para ACN/Ba y ACN/Cu y I− para CH3I/Ba. Para el sistema ACN/Cu, la medida del cociente CN−/e− en función de la longitud de onda del láser, demostró la selectividad vibracional del proceso al replicar el espectro de IR del ACN en fase gaseosa desplazado 20,17 cm−1 hacia el rojo. Estos experimentos se realizaron en un sistema experimental expresamente orientado a la espectroscopía en el infrarrojo. En un segundo sistema experimental especialmente diseñado para la detección y el análisis de electrones de baja energía generados en metal mediante luz láser visible, se estudiaron por primera vez las transiciones intrabanda entre estados sp de cobre generadas mediante 2PPE en Cu(100). Como resultado se consiguió identificar y medir la posición en energía del estado de volumen X′4 con alta precisión EX′4 =2,08±0,04 eV. En este sentido se desarrolló un modelo teórico para estudiar las transiciones intrabanda cerca del estado de alta simetría X. Los ajustes del modelo ofrecieron un valor de energía por fonón de ≈5 meV...

Obtención de láminas delgadas de Y-Ba-Cu-O sobre Si (100)

Se ha utilizado la evaporación secuencial de Cu, Y2O3 y BaF2 para la obtención de láminas delgadas superconductoras de YBa-CuO sobre substratos de Si monocristalino con orientación [100], recubiertos con una lámina barrera de Zr02. Se han estudiado los efectos de la variación de los espesores relativos de las láminas constituyentes y del espesor total de la lámina resultante. Las láminas se han caracterizado mediante medidas de la variación de la resistencia con la temperatura, microscopía electrónoca de barrido, difractometría de rayos X, microson-da electrónica y espectometría de masas de iones secundarios. Las láminas presentan un ligero carácter semiconductor en el estado normal, con temperaturas de inicio de la transición su-perconductora alrededor de 90 K, y resistencia nula, en el mejor de los casos, a 45 K.

Estudo eletroquímico de uma liga de Cu-Zn-Al, monofásico de fase'beta' poli e monocristalina com orientação (100)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Quantification of some nonsteroidal anti-inflammatory drugs as reducing agents of Cu(II)/4,4 '-dicarboxy-2,2 '-biquinoline complexes in cationic micellar medium

A simple method was developed for spectrophotometric determination of some nonsteroidal anti-inflammatory drugs (meloxicam, piroxicam and tenoxicam) based on the reduction of copper(II) in buffered solution (pH 7.0) and micellar medium containing 4,4'-dicarboxy-2,2'-buffered solution (pH 7.0) and micellar medium containing 4,4'-dicarboxy-2,2'-biquinoline acid. The-biquinoline acid. The absorbance values at 558 nm, characteristic of the formed Cu(I)/4,4'-dicarboxy-2,2'-biquinoline complexes, are linear with the concentrations (5.7-40 mmol L(-1), n = 5) of these oxicams (meloxicam r = 0.998; piroxicam and tenoxicam r = 0.999). The limit of detection values, in mmol L(-1), calculated for meloxicam (2.7), piroxicam (1.2) and tenoxicam (1.3) was obtained with 99% confidence level and the relative standard deviations for meloxicam (3.1%), piroxicam (5.1%) and tenoxicam (1.2%) were calculated using a 25 mmol L(-1) solution (n = 7). Mean recovery values for meloxicam, piroxicam and tenoxicam forms were 100 +/- 6.9, 98.6 +/- 3.6 and 99.4 +/- 2.5%, respectively. The conditional potential of Cu(II)/Cu(I) in complex medium of 7.5 mmol L(-1) BCA was determined to be 629 +/- 11 mV vs. NHE.

Direct and Simultaneous Determination of Cd Cu, and Se in Blood Samples by Graphite Furnace Atomic Absorption Spectrometry

A graphite furnace atomic absorption spectrometric method is proposed for the direct and simultaneous determination of Cd, Cu, and Se in human blood. Samples were diluted 1:10 (v/v) in 0.5% (v/v) HNO(3) + 0.5% (v/v) Triton X-100 solution. For 12 mu L injected sample volume + 5 mu L, of 1000 mg L(-1) Pd(NO(3))(2) + 3 mu L of 1000 mg L(-1) Mg(NO(3))(2), the calculated characteristic masses (mo) were 0.9 pg Cd, 16 pg Cu, and 39 pg Se, which are close to those mo values for single-element conditions for THGA furnace (1.3 pg Cd, 17 pg Cu, and 45 pg Se). Calibration curves with linear correlations better than 0.999 were obtained. The limits of detection (LOD) were 0.03 mu g L(-1) Cd, 0.075 mu g L(-1) Cu and 0.3 mu g L(-1) Se, and the relative standard deviations (n= 12) were 2.5%, 0.3%, and 1.5%, respectively. The method was applied for Cd, Cu, and Se determination in 10 human blood samples and the results were in agreement at the 95% confidence level with those obtained by inductively coupled plasma mass spectrometry. Concentrations of analytes in the selected blood samples varied from 1.7 to 3.2 mu g L(-1) Cd, 700 to 921.7 mu g L(-1) Cu, and from 68.6 to 350 mu g L(-1) Se. The accuracy of the proposed method was also evaluated by an addition-recovery experiment and recoveries of Cd, Cu, and Se added to blood samples ranged from 99-109%, 91-103%,and 93-103%, respectively.

Structural Dynamics in (ND4)2[Cu(D2O)6](SO4)2

The extended X-ray absorption fine structure spectroscopy (EXAFS) of (ND4)(2)[CU(D2O)(6)](SO4)(2) at 5, 14,100, 200, and 298 K is reported. This indicates that the Cu-O bond lengths of the Cu(D2O)(6)(2+) ion do not change significantly within this temperature range, which contrasts with EPR results and X-ray and neutron diffraction experiments, which imply that two of the Cu-(D2O) bonds converge in length as the temperature is raised. The EXAFS measurements thus confirm that the bond distances yielded by the diffraction experiments refer to the average positions of ligands involved in a dynamic equilibrium in which the directions of the long and intermediate bonds of the Jahn-Teller distorted Cu(D2O)(6)(2+) ion are interchanged in the crystal lattice. Analysis of the displacement parameters is consistent with this interpretation, as are the wave functions calculated using a model involving Jahn-Teller vibronic coupling and the influence of lattice strain interactions.

The effect of trace elements on the sintering of an Al-Zn-Mg-Cu alloy

Trace elements can have a significant effect on the processing and properties of aluminium alloys, including sintered alloys. As little as 0.07 wt% (100 ppm) lead, tin or indium promotes sintering in an Al-Zn-Mg-Cu alloy produced from mixed elemental powders. This is a liquid phase sintering system and thin liquid films form uniformly throughout the alloy in the presence of the trace elements, but liquid pools develop in their absence. Analytical transmission electron microscopy indicates that the trace elements are confined to the interparticle and grain boundary regions. The sintering enhancement is attributed to the segregation of the microalloying addition to the liquid-vapour interface. Because the microalloying elements have a low surface tension, they lower the effective surface tension of the liquid. This reduces the wetting angle and extends the spreading of the liquid through the matrix. An improvement in sintering results. (C) 2001 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Adsorção de Cu e Zn num Latossolo Vermelho tratado com dejetos suínos

O Cu e Zn oriundos dos dejetos suínos podem se acumular no solo, oferecendo riscos para a saúde humana e a animal. O objetivo deste trabalho foi determinar a capacidade de adsorção e a competição de Cu e Zn num Latossolo Vermelho distroférrico, que recebeu aplicações continuadas de dejetos suínos, com taxa de aplicação de 200 m³ ha-1 ano-1,durante sete anos, e comparar a adsorção com solo que nunca recebeu dejeto. Para avaliar a adsorção do Cu e Zn, foram aplicados ao solo soluções de Cu e Zn, nas doses de 0, 25, 50, 100, 150, 200, 400, 1.200 µmol L-1 e relação solo: solução final de 1:100. Para a obtenção das doses de Zn e Cu foi utilizada solução padrão Merck® Certipur 1.000 mg L-1. A adsorção de Cu apresentou comportamento sigmoide (isoterma tipo S), em solo sem dejeto (SD), e comportamento linear (isoterma tipo C), em solo com dejeto (CD). A capacidade máxima de adsorção (CMA) de Cu no solo SD foi de 3.021 mg kg-1. Para Zn, todas as isotermas apresentaram comportamento linear. Não foi atingida a capacidade máxima de adsorção, no tratamento CD, para Cu e Zn. Esses resultados indicam que o Latossolo estudado apresenta alta capacidade para reter o Cu e Zn oriundos dos dejetos suínos.

Pizgrischite, (Cu,Fe)Cu14PbBi17S35, a new sulfosalt from the Swiss Alps: Description, crystal structure and occurrence

Pizgrischite, (Cu,Fe)Cu14PbBi17S35, is a new mineral species named after the type locality, Piz Grisch Mountain, Val Ferrera, Graubunden, Switzerland. This sulfosalt occurs as thin, striated, metallic lead-grey blades measuring up to I cm in length, embedded in quartz and associated with tetrahedrite, chalcopyrite, pyrite, sphalerite, emplectite and derivatives of the aikinite-bismuthinite series. In plane-polarized light, the new species is brownish grey with no perceptible pleochroism; under crossed nicols in oil immersion, it presents a weak anisotropy with dark brown tints. Minimum and maximum reflectance values (in %) in air are: 40.7-42.15 (470 nm), 41.2-43.1 (546 nm), 41.2-43.35 (589 nm) and 40.7-43.3 (650 nm). Cleavage is perfect along 001 I and well developed on {010}. Abundant polysynthetic twinning is observed on (010). The mean micro-indentation hardness is 190 kg/mm(2) (Mohs hardness 3.3), and the calculated density is 6.58 g/cm(3). Electron-microprobe analyses yield (wt%; mean result of seven analyses): Cu 16.48, Pb 2.10, Fe 0.77, Bi 60.70, Sb 0.35, S 19.16, Se 0.04, total 99.60. The resulting empirical chemical formula is (Cu15.24Fe0.80Pb0.60)(Sigma 16.64)(Bi17.07Sb0.17)(Sigma 17.24)(S35.09Se0.03)(Sigma 35.12), in accordance with the formula derived from the single-crystal refinement of the structure, (Cu,Fe)Cu14PbBi17S35. Pizgrischite is monoclinic, space group C2/m, with the following unit-cell parameters: a 35.054(2), b3.91123(I), c43.192(2) angstrom, beta 96.713(4)degrees, V5881.24 angstrom(3), Z=4. The strongest seven X-ray powder-diffraction lines [d in angstrom (I)(hkl)] are: 5.364(40)((6) over bar 04), 4.080(50)((8) over bar 05), 3.120(40)(118), 3.104(68)((3) over bar 18), 2.759(53) ((9) over bar 11),2.752(44)(910) and 1.956(100)(020). The crystal structure is an expanded monoclinic derivative of kupcikite. Pizgrischite belongs to the cuprobismutite series of bismuth sulfosalts but, sensu stricto, it is not a homologue of cuprobismutite. At the type locality. pizarischite is the result of the Alpine metamorphism under greenschist-facies conditions of pre-Tertiary hydrothermal Cu-Bi mineralization.

Mobilidade de P, Cu e Zn em colunas de solo sob sistema de semeadura direta submetido às adubações mineral e orgânica

A retenção, no perfil do solo, de elementos minerais aplicados em sua superfície é fundamental para a manutenção da qualidade da água. Nesse sentido, o objetivo deste trabalho foi avaliar o efeito da aplicação de dejeto líquido de suíno e adubo mineral na lixiviação do P, Cu e Zn em colunas indeformadas de solo (25 cm de altura e 20,3 cm de diâmetro) retiradas de uma área de Latossolo Vermelho eutroférrico típico sob semeadura direta. A água foi aplicada nas colunas de forma ininterrupta, na quantidade correspondente a três volumes da porosidade total do solo (10.020 cm³), sendo a coleta e análise dos elementos subdivididas em cinco frações. Cada volume de poros (3.340 cm³) corresponde a um turno de água percolada, e o primeiro volume foi fracionado em três coletas. A concentração dos elementos no solo foi determinada nas camadas de 0 a 2,5, 2,5 a 10 e 10 a 20 cm. A retenção de P, Cu, e Zn no solo, em relação ao aplicado via dejeto líquido de suíno, foi de 99,6, 98,8 e 100 %, respectivamente. Para o P aplicado via adubo mineral, a retenção foi de 89,7 %. Independentemente do tipo de adubo, as concentrações de P, Cu e Zn no solo foram maiores na camada de 0 a 2,5 cm. Esses resultados indicam o baixo potencial de lixiviação desses elementos, o que sugere ser importante o uso de práticas de manejo e conservação do solo e da água que proporcionem a contenção e a infiltração do escoamento superficial.

Quasi real-time Raman studies on the growth of Cu-In-S thin films

In this work annealing and growth of CuInS2 thin films is investigated with quasireal-time in situ Raman spectroscopy. During the annealing a shift of the Raman A1 mode towards lower wave numbers with increasing temperature is observed. A linear temperature dependence of the phonon branch of ¿2 cm¿1/100 K is evaluated. The investigation of the growth process (sulfurization of metallic precursors) with high surface sensitivity reveals the occurrence of phases which are not detected with bulk sensitive methods. This allows a detailed insight in the formation of the CuInS2 phases. Independent from stoichiometry and doping of the starting precursors the CuAu ordering of CuInS2 initially forms as the dominating ordering. The transformation of the CuAu ordering into the chalcopyrite one is, in contrast, strongly dependent on the precursor composition and requires high temperatures.

Oxidized oils and dietary zinc and alpha-tocopheryl acetate supplementation: effects on rabbit plasma, liver and meat fatty acid composition and meat Zn, Cu, Fe and Se content

The effects of the addition of heated oils to feeds (3%, w/w) and the dietary supplementation with a-tocopheryl acetate (TA; 100 mg/kg) and Zn (200 mg/kg) on rabbit tissue fatty acid (FA) composition and on the Zn, Cu, Fe and Se content in meat were assessed. Heating unrefined sunflower oil (SO) at 558C for 245 h increased its content in primary oxidation products and reduced its a-tocopherol content. However, this did not significantly affect tissue FA composition. Heating SO at 1408C for 31 h increased its content in secondary oxidation products and in some FA isomers asc9,t11-CLA and di-trans CLA. This led to increases in di-trans CLA in liver and in t9,c12-18:2 in meat. The c9,t11-CLA was the most incorporated CLA isomer in tissues. The dietary supplementation with a-TA did not affect the FA composition of plasma, liver or meat. The cooking of vacuum-packed rabbit meat at 788C for 5 min reduced significantly but slightly its polyunsaturated FA content. The dietary supplementation with Zn did not modify the content of Zn, Fe or Se in meat, but it reduced its Cu content. On the other hand, it increased the content of some FAs in meat when SO heated at 1408C for 31 h was added to feeds.

Methanol steam reforming over Cu/CeO2 catalysts: influence of zinc addition

Methanol steam reforming reaction was studied over Cu(5 wt.%)/CeO2 with and without the presence of Zn. The Zn addition decreased the Cu+2 reducibility and increased the oxygen mobility of ceria. The main products were CO2 and H2 with small amount of CO. Selectivity to CO decreased with the Zn addition and it was lower at lower reaction temperatures and lower space velocities. At 230 ºC and W/F MeOH = 648 g min mol-1 selectivities to H2 and to CO2 were 100% on Zn/Cu/Ce. The catalytic results indicated that CO was mainly a secondary product formed from reverse water gas shift reaction.

Simultaneous preconcentration of Cu(II), Cd(II) and Mn(II) on silica-polyethylene glycol and determination by flame atomic absorption spectrometry

A simultaneous solid phase extraction procedure for enrichment of Cu(II), Cd(II) and Mn(II) has been developed. The method is based on adsorption of Cu(II), Cd(II) and Mn(II) ions on polyethylene glycol-silica gel pre-conditioned with acetate buffer (pH 5.5). The adsorbed metal ions are eluted with nitric acid (1 mol L -1) and determined by flame atomic absorption spectrometry. The calibration graph was linear in the range of 2-140 ng mL-1 for Cu(II), 1-40 ng mL-1 for Cd(II) and 4-100 ng mL-1 for Mn(II). The limits of detection were 0.66, 0.33 and 1.20 ng mL-1 for Cu(II), Cd(II) and Mn(II), respectively.