Secagem e formação de sementes duras em mucuna-preta

A mucuna-preta, leguminosa empregada como adubação verde e forrageira, produz sementes com dormência causada pela impermeabilidade do tegumento à água (dureza). O objetivo do trabalho foi estudar as relações entre a secagem das sementes no interior das vagens e a ocorrência desse fenômeno. Para tanto, nas colheitas realizadas semanalmente entre 40 e 89 dias após o florescimento, foram obtidas sementes de vagens submetidas ou não à secagem. Foram realizadas determinações de teor de água das sementes na colheita, coloração nas vagens e nas sementes no momento da colheita, condutividade elétrica, germinação e presença de sementes duras. A secagem das sementes nas vagens, separadas da planta-mãe, favorece o surgimento da dureza; essa ocorrência, contudo, é atenuada com o retardamento da referida separação.

Viabilidade do uso de secadores solar de convecção natural e forçada para a secagem do coco Licuri

Licuri is a palm tree from the semiarid regions of Bahia State, Brazil. It is an important source of food and feed in that region, since their nuts are commonly eaten by humans and used as maize substitute for poultry feeding. The aim of this dissertation is to study the feasibility for use of natural convection solar dryers and forced being compared with the traditional drying outdoors for drying coconut licuri Syagrus coronate. The study led to the construction of two prototype solar dryer for carrying out experiments proving: model Solar Drying System Direct Exposure to Natural Convection built with wood, has a drying chamber with direct cover transparent glass laminates 4 mm, using techniques for proper isolation of the drying chamber. The two prototypes were comparatively analyzed for performance and drying efficiency with traditional extractive use by the community. Were evaluated the variables: time and drying rates and quality of the final samples of coconut licuri. The fruits were harvested and brought the town of Ouricuri, in the city of Caldeirão Grande, BA for the experiments comparing the three methods of drying was used a standard load of 4.0 kg The quantitative analysis for the result of the drying rate was found in 74% yield and 44% for natural and forced convection respectively compared with the traditional drying. These drying rates represent variation 3-5 times lower. Drying using forced convection licuri showed better quality, was found in a reddish pulp, representing the quantities that were kept of the nutrient beta carotene, and not notice the flavor change from the previous system, the final cost of construction of this system were higher . The prototypes built competitive advantage and had testified fully to resolve the technical difficulties previously encountered in the production of products made of coconut licuri. Allowing add value and increase their potential use for the fruit extractive communities of semi-arid region of Bahia

Avaliação da secagem do bagaço de cajá usando planejamento fatorial composto central

This work deals with the kinetics assay of Cajá (Spondias mombin L.) bagasse drying by an experimental design using a tray dryer. In order to add-value to this product a kinetic study has been carried out. A central composite experimental design has been carried out to evaluate the influence of the operational variables: input air temperature (55; 65 e 75ºC); the drying air velocity (3.2; 4.6 e 6.0 m/s) and the fixed bed thickness (0.8; 1.2 e 1.6 cm) and as response variable the the moisture content (dry basis). The results showed that the diffusional Fick model fitted quite well the experimental data. The best condition found has been input air temperature of 75ºC, drying air velocity of 6.0 m/s as well as fixed bed thickness of 0.8 cm. The experimental design assay showed that the main effects as well as the second ones were significant at 95% confindance level. The best operational condition according to statistical planning was 75 oC input air temperature, 6.0 m.s-1 drying air velocity and 0.8 cm fixed bed thickness. In this case, the equilibrium moisture content (1.3% dry basis) occured at 220 minutes

Produtividade de amendoim em função da calagem e do método de secagem

Estudar o efeito da calagem e do método de secagem na produtividade do amendoim (Arachis hypogea L., cv. Botutatu) foi o objetivo deste trabalho, conduzido num solo Latossolo Vermelho-Escuro, textura média, em São Manuel, São Paulo. Os tratamentos consistiram de ausência ou presença de calagem (2,05 Mg ha-1) e secagem à sombra, ao sol e duas formas combinadas desta última com estufa. A calagem eliminou a fitotoxicidade de manganês, melhorando a nodulação e a nutrição nitrogenada, que, conseqüentemente, levaram ao aumento do número de ramificações, de vagens por planta e da produtividade. Com a calagem, observou-se também redução nas perdas durante a colheita. Das formas de secagem, a realizada à sombra e a combinada campo-estufa foram as que proporcionaram maiores produtividades, por permitirem melhor maturação dos frutos e menores perdas na colheita.

Qualidade fisiológica de sementes de milho-doce BR 400 (bt) em função do teor de água na colheita e da temperatura de secagem

O objetivo deste estudo foi avaliar a qualidade fisiológica das sementes de milho-doce em função do teor de água na colheita e da temperatura de secagem em espiga. O experimento foi instalado na área experimental da FCA/Unesp, Botucatu-SP. Utilizou-se a cultivar BR 400 (bt) 'Super doce'. O delineamento experimental empregado foi o de blocos ao acaso com seis repetições, constituindo os tratamentos as épocas de colheitas. As colheitas das espigas foram iniciadas após a maturidade fisiológica; após despalhadas e divididas em duas porções, as espigas foram submetidas a secagem em estufas com circulação forçada nas temperaturas de 30 e 40ºC. Foi utilizada uma testemunha com sementes secadas no campo com 10,1% de teor de água. Foram determinados os teores de água das sementes, inicial e após a secagem, de todas as colheitas. Após a secagem, as espigas foram debulhadas manualmente, as sementes acondicionadas em saco de papel e armazenadas em condições ambientais de laboratório. As avaliações da qualidade fisiológica das sementes (emergência de plântulas no campo, índice de velocidade de emergência, matéria seca de plântulas, germinação, vigor-primeira contagem do teste de germinação, envelhecimento acelerado, teste de frio, condutividade elétrica e teores de Ca, Mg, K e Na lixiviados na solução do teste de condutividade elétrica) foram realizadas antes e após seis meses de armazenamento. As sementes de milho-doce cultivar BR 400 (bt), com teor de água igual ou menor do que 35%, podem ser submetidas à secagem em espiga a temperatura de 30 ou 40ºC, sem perdas significativas em sua qualidade fisiológica.

Maturação e secagem de sementes de Peltophorum dubium (Spreng.) Taubert (CANAFÍSTULA)

O trabalho foi desenvolvido em Botucatu, SP, e teve por objetivo determinar o momento de ocorrência do máximo potencial de germinação durante a maturação das sementes de canafístula, relacionando-a com a secagem dos frutos. Cinco árvores, em final de floração, tiveram 15 inflorescências etiquetadas em 06/02/ 2002. As colheitas, realizadas semanalmente, foram iniciadas na quinta semana após a etiquetagem (35 DAE) e finalizaram quando ocorreu o início da dispersão dos frutos (98 DAE), totalizando 10 colheitas. Os frutos das cinco plantas foram colhidos e avaliados separadamente. em cada colheita, os frutos foram divididos em duas porções: uma teve as sementes extraídas (sementes frescas), e a outra foi posta para secar em ambiente natural de laboratório para, então, se extraírem as sementes (sementes secas). Determinaram-se o teor de água e a massa seca de 100 sementes frescas e 100 secas. Os testes de germinação das sementes, frescas e secas, foram realizados com e sem escarificação. O delineamento experimental utilizado foi o de blocos casualizados, considerando-se a árvore e o bloco. A maior capacidade germinativa das sementes foi atingida após a ocorrência do máximo acúmulo de massa. O máximo potencial de germinação, detectado nas sementes escarificadas, foi observado no início da dispersão, quando predominavam sementes duras. A maturação, a germinação e a instalação da dormência em semente imatura foram antecipadas com a sua secagem no interior do fruto separado da planta-mãe.

Automação de um sistema rotatório para secagem do rejeito de maracujá

The rotary dryer is one of the most used equipments in processing industries. Its automatic control mode of operation is important specially to keep the moisture content of the final product in the desired value. The classical control strategies, like PID (proportional integral derivative) control, are largely used in the industrial sector because of its robustness and because they are easy to be implemented. In this work, a data acquisition system was implemented for monitoring the most relevant process variables, like: both inlet and outlet drying air temperature, dryer rotation, outlet air speed and humidity, and mass of the final product. Openloop tests were realized to identify a mathematical model able to represent the drying process for the rotary system. From this model, a PID controller was tuned using a direct synthesis method, assuming a first order trajectory. The PID controller was implemented in the system in order to control the inlet drying air temperature. By the end, closedloop tests (operating in automatic mode) were realized to observe the controller performance, and, after setting the best tune, experiments were realized using passion fruit seeds as raw material. The experiments realized in closedloop showed a satisfactory performance by the implemented control strategy for the drying air temperature of the rotary system

Secagem do resíduo de acerola (Malphigia emarginata D.C.): estudo do processo e avaliação do impacto sobre o produto final

Brazil, one of the largest agricultural producers in the world, has managed in recent years to significantly improve its production. However, in response to this advance in the agro-industrial sector, the generation of agro-industrial residues has also increased. New technological alternatives have to be implemented in order to bring economic and rational use of this material and drying is one of the possible choices. Considering the great importance that bioactive compounds present for food science and technology, this research aims to evaluate the air-drying process of acerola residue in a tray convective drier under controlled temperature (60, 70 e 80ºC), air velocity (4.0, 5.0 e 6.0 m/s) and material width (0.5, 0.62 e 0.75 cm) by applying an experimental planning 23 + 3. Based on that, the impact on physical-chemical characteristics, color, bioactive compounds concentration and antioxidant activity of dried acerola waste was evaluated, having the in natura and freeze dried waste as control groups. Dried acerola residue presented natural pigments, mainly carotenoids (143.68 - 68.29 mg/g) and anthocyanins (290.92 - 90.11 mg/100 g), which explain the red and yellow instrumental color parameters observed. The acerola residue powder is also rich in phenolic compounds (3261.11 -2692.60 mgGAEeq/100g), proanthocyanidins (61.33-58.46 eq/100g), ascorbic acid (389.44 739.29 mg/100 g) and DPPH antioxidant activity (20.91 24.72 μg Trolox eq/g). Results show decreased concentration of phenolic compounds, anthocyanins, carotenoids, proanthocyanidins and ascorbic acid caused by the air-drying process. However, even after the observed drying losses, the acerola residue powder can be considered a high value food ingredient, considering the high bioactive compounds concentration found in the final product, as well as the colorimetric characterization and microbiological stability of the dried powder

Secagem do resíduo industrial da acerola em leito de jorro: estudos fluidodinâmicos e análise do desempenho do secador

In this research, the drying process of acerola waste was investigated by using a spouted bed drier. The process was conducted using high density polyethylene inert particles with the objective of producing an ascorbic acid-rich final product. The fruit waste was ground and used to prepare different water-maltodextrin suspensions. Initially, fluidynamical experiments were conducted in order to evaluate the feeding effect on the spouted bed drier fluidynamics behavior. The experimental planning 23 + 3 was used to investigate the effect of the following variables: solids concentration, drying air temperature, intermittence time, production efficiency, solids retention and product losses by elutriation of fine particles on drier walls. The effect of selected independent variables on the drier stability was also evaluated based on a parameter defined as the ratio between the feed suspension volume and the total inert particles volume. Finally, the powder quality was verified in experiments with fixed feed flow and varying air drying temperature, drying air velocity and intermittence time. It was observed that the suspension interferes in the spouted bed drier fluidynamics behavior, and higher air flow is necessary to stabilize the drier. The suspension also promotes the expansion of the spouted bed diameter, decreases the solid circulation and favors the air distribution at the flush area. All variables interfere in the spouted bed performance, and the solids concentration has a major effect on the material retention and losses. The intermittence time also has great effect on the stability and material retention. When it comes to production efficiency, the main effect observed was the drying air temperature. First order models were well adjusted to retention and losses data. The acerola powder presented ascorbic acid levels around 600 to 700 mg/100g. Similar moisture and ascorbic acid levels were obtained for powders obtained by spouted bed and spray drier. However, the powder production efficiency of the spray drier was lower when compared to spouted bed drier. When it comes to energetic analysis, the spray drier process was superior. The results obtained for spouted bed drier are promising and highly dependent on the operational parameters chosen, but in general, it is inferred that this drying process is adequate for paste and suspension drying

Avaliacao de dados de secagem de suspensoes de polpas de frutas em leito de jorro com alimentacao intermitente

The objective of this work was the development and improvement of the mathematical models based on mass and heat balances, representing the drying transient process fruit pulp in spouted bed dryer with intermittent feeding. Mass and energy balance for drying, represented by a system of differential equations, were developed in Fortran language and adapted to the condition of intermittent feeding and mass accumulation. Were used the DASSL routine (Differential Algebraic System Solver) for solving the differential equation system and used a heuristic optimization algorithm in parameter estimation, the Particle Swarm algorithm. From the experimental data food drying, the differential models were used to determine the quantity of water and the drying air temperature at the exit of a spouted bed and accumulated mass of powder in the dryer. The models were validated using the experimental data of drying whose operating conditions, air temperature, flow rate and time intermittency, varied within the limits studied. In reviewing the results predicted, it was found that these models represent the experimental data of the kinetics of production and accumulation of powder and humidity and air temperature at the outlet of the dryer

Avaliação da aplicação de modelos para a secagem de pastas e suspensões em leito de jorro com alimentação contínua

This work studies the development, implementation and improvement of a macroscopic model to describe the behavior of the spouted bed dryer with continuous feeding for pastes and suspensions drying. This model is based on the CST model (Freire et al., 2009) and the model of Fernandes (2005), whose theoretical foundation is based on macroscopic mass and heat balances for the three phases involved in the process: gas, liquid and solid. Because this technique is quite relevant, the studies of modeling and simulation of spouted bed drying are essential in the analysis of the process as a whole, because through them it is possible to predict and understand the behavior of the process, which contributes significantly to more efficient project and operation. The development and understanding of the phenomena involved in the drying process can be obtained by comparing the experimental data with those from computer simulations. Such knowledge is critical for choosing properly the process conditions in order to obtain a good drying efficiency. Over the past few years, researches and development of works in the field of pastes and suspensions drying in spouted bed has been gaining ground in Brazil. The Particulate Systems Laboratory at Universidade Federal do Rio Grande do Norte, has been developing several researches and generating a huge collection of experimental data concerning the drying of fruit pulps, vegetables pastes, goat milk and suspensions of agro-industrial residues. From this collection, some data of goat milk and residue from acerola (Malpighia glabra L.) drying were collected. For the first time, these data were used for the development and validation of a model that can describe the behavior of spouted bed dryer. Thus, it was possible to model the dryer and to evaluate the influence of process variables (paste feeding, temperature and flow rate of the drying air) in the drying dynamics. We also performed water evaporation experiments in order to understand and to study the behavior of the dryer wall temperature and the evaporation rate. All these analysis will contribute to future works involving the implementation of control strategies in the pastes and suspensions drying. The results obtained in transient analysis were compared with experimental data indicating that this model well represents the process

Secagem de grãos de girassol em leito fixo e em leito de jorro

This work studies two methods for drying sunflower grains grown in the western region of Rio Grande do Norte, in the premises of the Instituto Federal de Educação, Ciência e Tecnologia do Rio Grande do Norte - IFRN - Campus Apodi. This initiative was made because of the harvested grain during the harvest, being stored in sheds without any control of temperature, humidity etc. Therewith, many physical, chemical and physiological characteristics are compromised and grains lose much quality for oil production as their germination power. Taking into account that most of the stored grain is used for replanting, the studied methods include drying of grains in a thin layer using an oven with air circulation (fixed bed) and drying in a spouted bed. It was studied the drying of grains in natura, i.e., newly harvested. The fixed bed drying was carried out at temperatures of 40, 50, 60 and 70°C. Experiments in spouted bed were performed based on an experimental design, 2² + 3, with three replications at the central point, where the independent variables were grains load (1500, 2000 and 2500 g) and the temperature of the inlet air (70, 80, and 90 °C), obtaining the drying and desorption equilibrium isotherms. Previously, the characteristic curves of the bed were obtained. Both in the fixed bed as in the spouted bed, drying and desorption curves were obtained by weighing the grains throughout the experiments and measurements of water activity, respectively. The grains drying in the spouted bed showed good results with significant reduction of processing time. The models of FICK and PAGE were fitted to the experimental data, models which will represent the drying of grains both in the fixed bed as in the spouted bed. The desorption curves showed no influence of the processing temperature in the hygroscopic characteristics of the grains. The models of GAB, OSWIN and LUIKOV could well represent the desorption isotherms

Jambolão (Syzygium cumini) desidratado por liofilização e secagem em leito de jorro: avaliação do impacto do processo de secagem e caracterização do potencial funcional do produto final

Tropical fruits have been extensively studied due to their functional potential attributed to the presence of natural bioactive compounds. The exotic fruit jambolan (Syzygium cumini) has been reported for its appreciable amount of phenolic compounds, especially anthocyanins and antioxidant capacity. Nevertheless, there are hardly any derived jambolan products in the Brazilian market. In addition to that, considerable volumes of fruit are lost due to their high perishability. Dried fruits have become an important fruit market segment due to its weight and volume reduction and decreased transportation and storage costs. Thus, this study evaluated the jambolan pulp submitted to spouted bed drying (JLJ) and lyophilization (JLI), besides assessing the drying impact on the final product. In order to achieve this, the process performance was calculated and compared, as well the physicochemical and bioactive characteristics (moisture, water activity (aw), solubility, hygroscopicity, density, color, structure through images obtained by scanning electron microscopy (SEM), concentration of bioactive (total phenolic compounds (TPC), anthocyanins, proanthocyanidins and ascorbic acid) and antioxidant activity. The results showed drying efficiency higher than 60% for both products and that JLJ group showed higher moisture and water activity when compared to the JLI group (p<0.05). The two types of drying were able to produce stable final product in the microbiological point of view, given that both showed aw < 0.6. The final products exhibited high solubility (73.7 to 81.6%) and low hygroscopicity (9.8 to 11.6%), desirable characteristics for dehydrated foods. Despite the losses caused by drying, the dried jambolan pulp by both methods showed high TPC (468.6 to 534.0 mg GAE/100g dm), anthocyanins (from 491.9 to 673.4 mg. eq. cyanidin-3-glicoside/100g dm), proanthocyanidins (66.9 to 76.6 mg QTE/g dm) and ascorbic acid (156.4 to 186.8 mg/100 g dm). Taken together, the results of this study reveal spouted dried and freeze dried jambolan pulp as bioactive-rich natural products with suitable physicochemical and functional characteristics to be used as food ingredients. The data also demonstrate the drying techniques as rational strategies for the exploitation of the exotic fruit jambolan

Estudo da secagem do feijão verde (Vigna unguiculata L. Walp) - análise experimental do processo combinado leito fixo/leito de jorro

Green bean is considered as one of most traditional Brazilian Northeast dishes. Green beans drying preliminary experiments show that combine processes, fixed-bed/spouted bed, resulted in dehydrated beans with uniform humidity and the recovery of the beans properties after their rehydration. From this assays was defined an initial humidity suited for the spouted bed process. A fixed-bed pre-drying process until a level of 40% humidity gave the best results. The spouted bed characteristic hydrodynamic curves were presented for different beans loads, where changes in the respective beans physical properties were evidenced during the fluidynamic assay, due simultaneous drying process. One 22 factorial experimental design was carried out with three repetition in the central point, considering as entry variables: drying air velocity and temperature. The response variables were the beans brakeage, water fraction evaporated during 20 and 50 minutes of drying and the humidity ratio. They are presented still the modeling of the drying of the green beans in fine layer in the drier of tray and the modeling of the shrinking of the beans of the drying processes fixed-bed and spouted bed

Sistema de secagem solar para frutos tropicais e modelagem da secagem de banana em um secador de coluna estática

In this study were projected, built and tested an electric solar dryer consisting of a solar collector, a drying chamber, an exhaust fan and a fan to promote forced hot air convection. Banana drying experiments were also carried out in a static column dryer to model the drying and to obtain parameters that can be used as a first approximation in the modeling of an electric solar dryer, depending on the similarity of the experimental conditions between the two drying systems. From the banana drying experiments conducted in the static column dryer, we obtained food weight data as a function of aqueous concentration and temperature. Simplified mathematical models of the banana drying were made, based on Fick s and Fourier s second equations, which were tested with the experimental data. We determined and/or modeled parameters such as banana moisture content, density, thin layer drying curves, equilibrium moisture content, molecular diffusivity of the water in banana DAB, external mass transfer coefficient kM, specific heat Cp, thermal conductivity k, latent heat of water evaporation in the food Lfood, time to heat food, and minimum energy and power required to heat the food and evaporate the water. When we considered the shrinkage of radius R of a banana, the calculated values of DAB and kM generally better represent the phenomenon of water diffusion in a solid. The latent heat of water evaporation in the food Lfood calculated by modeling is higher than the latent heat of pure water evaporation Lwater. The values calculated for DAB and KM that best represent the drying were obtained with the analytical model of the present paper. These values had good agreement with those assessed with a numeric model described in the literature, in which convective boundary condition and food shrinkage are considered. Using parameters such as Cp, DAB, k, kM and Lfood, one can elaborate the preliminary dryer project and calculate the economy using only solar energy rather than using solar energy along with electrical energy