PHASE-BEHAVIOR IN EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER SULFONE)

Phenolphthalein poly(ether ether sulphone) (PES-C) was found to be miscible with uncured bisphenol-A-type epoxy resin, i.e. diglycidyl ether of bisphenol A (DGEBA), as shown by the existence of a single glass transition temperature within the whole composition range. Miscibility between PES-C and DGEBA is considered to be due mainly to the entropy contribution. However, dynamic mechanical analysis (d.m.a.) and scanning electron microscopy (SEM) studies revealed that PES-C exhibits different miscibility with four cured epoxy resins (ER). The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. For the blends cured with amines (4,4'-diaminodiphenylmethane (DDM) and 4,4'-diaminodiphenylsulphone (DDS)), no phase separation occurs as indicated by either d.m.a. or SEM. However, for the blends cured with anhydrides (maleic anhydride (MA) and phthalic anhydride (PA)), both d.m.a. and SEM clearly show evidence of phase separation. SEM study shows that the two phases interact well in the MA-cured blend while the interface between the phases in the PA-cured blend is poorly bonded. The differences in the overall compatibility and the resulting morphology between the amine-cured and anhydride-cured systems have been discussed from the points of view of both thermodynamics and kinetics.

Total synthesis of cyanolide A and confirmation of its absolute configuration.

The tandem allylic oxidation/oxa-Michael reaction promoted by the gem-disubstituent effect and the 2-methyl-6-nitrobenzoic anhydride (MNBA)-mediated dimerization were explored for the efficient and facile synthesis of cyanolide A.

Polymeric materials based on silk proteins

Silks are protein-based fibers made by arthropods for a variety of task-specific applications. In this article, we review the key features of silk proteins. This article initially focuses on the structure and function of silk proteins produced naturally by silkworms and spiders, followed by the biological and technical processing of silk proteins into a variety of morphologies (including capsules, fibers, films, foams, gels and spheres). Finally, we highlight the potential applications of silk-based materials. 

Some aspects of the chemistry of 1, 3, 4 - Thiadiazolium salts and related compounds

The work described in this thesis has been divided into seven sections. The first section involves the preparation of N'-acyl-N'-arylN- benzothiohydrazides by the acylation of N'-aryl-N-benzothiohydrazides and is followed by a brief discussion of their possible conformation in solution. The second section deals with the preparation of 1,3,4-thiadiazolium salts by the action of perchloric acid/acetic anhydride on N'-acylN'- aryl-N-benzothiohydrazides and also by the reaction of N'-arylN- benzothiohydrazides with nitriles in an acidic medium. The preparation of 2-methylthio-I,3,4-thiadiazolium methosulfate by methylating the corresponding thione is also described. The third section deals with the reaction of 2-phenyl- and 2-methyl-I,3,4-thiadiazolium salts with alcohols in the presence of base. The stability and spectra of these compounds are discussed. Treatment of the 2-methyl-I,3,4-thiadiazolium salt with base was found to give rise to a dimeric anhydrobase and evidence supporting its structure is given. The anhydrobase could be trapped by a variety of acylating and thioacylating agents before dimerization occurred. In the fourth section, the reaction of N'-acyl-N'-aryl-N-benzothiohydrazides with a variety of acid anhydrides is described. These compounds were found to be identical with those obtained by acylating the anhydrobase. The mass spectral fragmentation of these compounds is described and the anomolous product obtained upon thiobenzoylation of 3-methyl-l-phenyl-pyrazal-5-one is also discussed. The fifth section deals with thioacyl derivatives of the anhydrobase which were prepared by the action of phosphorus pentasulfide upon the oxygen analogues and also obtained as the major product of the reaction of thioacetic acid with compounds related to N'-aryl-N-benzothiohydrazides. The mass spectra and p.m.r. spectra of these compounds are discussed. In the sixth section, the reaction of the 2-methylthio-l,3,4- thiadiazolium salt with active methylene compounds to give acyl and diacyl derivatives of the anhydrobase is described. Some aspects of these compounds are discussed. The seventh section describes the synthesis of ncyanine~' type dyes incorporating the l,3,4-thiadiazole ring and their spectra are briefly discussed.

The chemistry of heterocyclic methine bases and of their acyl and thioacyl derivatives

The work described in this thesis has been dtvided into six sections . The first section involves the reaction of 3,5-diphenyl-2-methyl-l,3,4-oxadiazolium perchlorate with acetic and benzoic anhydrides. The second section deals with the preparation and reactions of 1,3,4-thia diazolium salts. Some monomeric 1,3,4-thiadiazoline methine bases have also been prepared by reacting 1,3,4-thia d iaz ol ium s al t s with concen trated ammonium hydroxide solution. Variable temperature p.m.r. of 2-(3-acetylacetonylidene)-3,5-diphenyl-A4 -1,3,4-thiadiazoline has also been described. The third section deals with prepar a tion and reactions of some compounds in benzoxazole series. The fourth section deals with the prep a ration and reactions of N-alkyl-2-methylbenzothi azolium salts with base , a nd with some a cetylating and thioacetylating agents. Treatment of 2,3-dimethylbenzothiazolium iodide and of 3-ethyl-2-methylbenzothia zolium iodide with base wa s found to give the corresponding dimeric methine b a ses and evidence supporting their structure is also given. Thiol acetic acid was found to exchange 0 for S in its reactions with 2-acetonylidene-3-methylbenzothiazoline and 2-acetophenonylidene-3-methylbenzothi a zoline. (ii) In th e fifth section, the r eactions of 2,3-dimethylbenzselenazolium iodide with a variety of ac e tylating and thioacetylating agents has been described. The treatment of 2,3-dimethylbenzselenazolium iodide with base was found to give rise to a dimeric methine base and evidence supporting its structure is also given. The reactions of this dimeric methine b a se with benzoic anhydride and phenylisothiocyanate have also been described. The sixth section deals with the preparation and reactions of l-alkyl-2-methylquinolinium salts. Treatment of 1,2-dimethylquinolinium iodide and l-ethyl-2-methylquinolinium iodide was found to give the corresponding monomeric methine bases and evidence supporting their structure is also given. The E-type geometry of the olefinic bond in 2-acetonylidene-l-methylquinoline has been established on the basis of an N.O.E. experiment.

Studies on some Metal Complexes of Dithio Ligands

The thesis deals with our studies on the synthesis and elucidation of structure of some metal complexes of dithio ligands, such as the dithiocarbamates, xanthates and 2-aminocyclopent-1-ene-1-dithiocarboxylate and its N-alkyl derivatives.2-Aminocyclopent-1-ene-1-dithiocarboxylate (ACDA) is an interesting ligand, because of its potential dual capability of bonding between the metal and the ligand. Since the earlier reports on the complexes of ACDA contain contradictory ideas on the nature of its bonding, it was thought worthwhile to undertake a detailed and systematic study of these type of complexes. As the ACDA complexes have very low solubilities in solvents like chloroform, we have used the isopropyl derivative of ACDA as the ligand. The increased solubility of these complexes have made it possible to investigate their NMR and solution electronic spectra.The complexes of this ligand have not yet been reported in the literature.We have synthesised some new mixed ligand complexes of dithiocarbamates by reacting bis(dithiocarbamato)-µ-dichloro dicopper complexes (obtained by the reaction of mixed benzoic dithiocarbamic anhydride and copper(II) chloride) with ACDA or its N-alkyl derivatives.Interactions of metal halides with the mixed anhydrides formed from benzoylchloride and xanthates have also been investigated. Novel complexes of the type, [Cu2(RXant)CI] (R=i-Bu, i-Pr, n-Bu or n-Pr)) have been isolated from the reaction of copper(II) chloride and the mixed anhydride, and these reactions appear to be like the clock reactions reported in the literature.It also deal with the characterisation of the complexes of the type [Hg(R2d t c )X] (X=Cl, Br or 1),[Cu3(R2dtc)6][Cu2Br6] and [Cu(R2dtc)Cl2](R2=Me2,Et2,Pip,Morph or Pyrr)respectively, synthesised by simple and novel routes, different from those reported earlier.

Microwave-Assisted Derivatization of Cellulose in an Ionic Liquid: An Efficient, Expedient Synthesis of Simple and Mixed Carboxylic Esters

Microwave (MW)-assisted cellulose dissolution in ionic liquids (ILs) has routinely led either to incomplete biopolymer solubilization, or its degradation. We show that these problems can be avoided by use of low-energy MW heating, coupled with efficient stirring. Dissolution of microcrystalline cellulose in the IL 1-allyl-3-methylimidazolium chloride has been achieved without changing its degree of polymerization; regenerated cellulose showed pronounced changes in its index of crystallinity, surface area, and morphology. MW-assisted functionalization of MCC by ethanoic, propanoic, butanoic, pentanoic, and hexanoic anhydrides has been studied. Compared with conventional heating, MW irradiation has resulted in considerable decrease in dissolution and reaction times. The value of the degree of substitution (DS) was found to be DS(ethanoate) > DS(propanoate) > DS(butanoate). The values of DS(pentanoate) and DS(hexanoate) were found to be slightly higher than DS(ethanoate). This surprising dependence on the chain length of the acylating agent has been reported before, but not rationalized. On the basis of the rate constants and activation parameters of the hydrolysis of ethanoic, butanoic, and hexanoic anhydrides in aqueous acetonitrile (a model acyl transfer reaction), we suggest that this result may be attributed to the balance between two opposing effects, namely, steric crowding and (cooperative) hydrophobic interactions between the anhydride and the cellulosic surface, whose lipophilicity has increased, due to its partial acylation. Four ethanoate-based mixed esters were synthesized by the reaction with a mixture of the two anhydrides; the ethanoate moiety predominated in all products. The DS is reproducible and the IL is easily recycled. (C) 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 134-143, 2010

Application of 1-Allyl-3-(1-butyl)imidazolium Chloride in the Synthesis of Cellulose Esters: Properties of the Ionic Liquid, and Comparison with Other Solvents

The ionic liquid (IL), 1-allyl-3-(1-butyl)imidazolium chloride (AlBuImCl), has been synthesized and its properties determined. Increase in the temperature increased its conductivity and decreased its density, polarity, and viscosity. Microcrystalline cellulose (MCC), dissolves in thisIL by heating at 80 degrees C; this did not affect its degree of polymerization, decreased its index of crystallinity (Ic), and changed in morphology after regeneration. Convenient acylation of MCC was achieved by using 50% excess anhydride at 80 degrees C, for 24 or 48 h for acetic and butyric anhydride, respectively. The composition of the mixed esters depended on the initial ratio of the anhydrides, and their order of addition.

Formation and decomposition of N-alkyinaphthalimides: experimental evidences and ab initio description of the reaction pathways

The kinetics of hydrolysis of 1,8-N-butyl-naphthalimide (1,8-NBN) to 1,8-N-butyl-naphthalamide (1,8-NBAmide) and of 2,3-N-butyl-naphthalimide (2,3-NBN) to 2,3-N-butyl-naphthalamide (2,3-NBAmide), as well as the formation of the respective anhydrides from the amides were investigated in a wide acidity range. 1,8-NBN equilibrates with 1,8-NBAmide in mild alkali. Under the same conditions 2,3-NBN quantitatively yields 2,3-NBAmide. Over a wide range of acidities the reactions of the 1,8- and 2,3-N-butyl-naphthalamides (or imides) yield similar products but with widely different rates and at distinct pH`s. Anhydride formation in acid was demonstrated for 1,8-NBAmide. The reactions mechanisms were rationalized in the manifold pathways of ab initio calculations. The differences in rates and pH ranges in the reactions of the 1,8- and 2,3-N-butyl-naphthalamides were attributed to differences in the stability of the tetrahedral intermediates in alkali as well as the relative stabilities of the five and six-membered ring intermediates. The rate of carboxylic acid assisted 1,8-N-Butyl-naphthalamide hydrolysis is one of the largest described for amide hydrolysis models. Copyright (C) 2010 John Wiley & Sons, Ltd.

First report on the kinetics of the uncatalyzed esterification of cellulose under homogeneous reaction conditions: a rationale for the effect of carboxylic acid anhydride chain-length on the degree of biopolymer substitution

The kinetics of the homogeneous acylation of microcrystalline cellulose, MCC, with carboxylic acid anhydrides with different acyl chain-length (Nc; ethanoic to hexanoic) in LiCl/N,N-dimethylacetamide have been studied by conductivity measurements from 65 to 85 A degrees C. We have employed cyclohexylmethanol, CHM, and trans-1,2-cyclohexanediol, CHD, as model compounds for the hydroxyl groups of the anhydroglucose unit of cellulose. The ratios of rate constants of acylation of primary (CHM; Prim-OH) and secondary (CHD; Sec-OH) groups have been employed, after correction, in order to split the overall rate constants of the reaction of MCC into contributions from the discrete OH groups. For the model compounds, we have found that k((Prim-OH))/k((Sec-OH)) > 1, akin to reactions of cellulose under heterogeneous conditions; this ratio increases as a function of increasing Nc. The overall, and partial rate constants of the acylation of MCC decrease from ethanoic- to butanoic-anhydride and then increase for pentanoic- and hexanoic anhydride, due to subtle changes in- and compensations of the enthalpy and entropy of activation.

Amidverknüpfte Ferrocene - schaltbare molekulare Drähte und Sensoren

In dieser Arbeit werden Synthesen und Eigenschaften von Verbindungen mit einer oder mehreren Ferrocen- bzw. Biferroceneinheiten beschrieben, die über Amid-, Anhydrid- oder Harnstoff-Funktionen verknüpft oder mittels Amidfunktion an α-Aminosäurederivate gebunden sind. Als Zentralbausteine dienen die künstlichen Aminosäuren 1’-Aminoferrocen-1-carbonsäure (Fca) bzw. 1’-Aminobiferrocen-1-carbonsäure (Bfca). Die Ferroceneinheit agiert als redoxschaltbares Gelenk, die Amidfunktion ermöglicht die Ausbildung von Sekundärstrukturen und die Bindung von Anionen. Das redoxschaltbare „Multiwellenlängen“-Sensorpaar [Dansyl-Ala-Fca-Ala-CH2-Naphthyl]0/+ ist in der Lage, insgesamt sieben Anionen aufgrund von sechs einfach zu erhaltenden optischen Messwerten eindeutig zu diskriminieren. Die Vorzugskonformation des neutralen Rezeptors mit intramolekularen Wasserstoffbrücken wird mittels X-Ray, NMR- und DFT-Methoden im Festkörper, in Lösung und in der Gasphase bestimmt. Die oligomeren Fca-Verbindungen SG-Fcan-HN-Fc (SG = Boc, Fmoc; n = 1, 2) und SG-Fca2-OMe (SG = Boc, Fmoc) werden mittels Peptidkupplung in Lösung hergestellt, Fmoc-Fca3-Gly-OMe, Fmoc-Fcan-OMe (n = 3-5) und Fmoc-Fca4-NH2 dagegen durch ein neu entwickeltes Festphasensynthese-Protokoll. Die amidverknüpften Verbindungen bilden eine „Zick-Zack“-Struktur mit 1,2’-Konformation der Fca-Einheiten und achtgliedrigen intramolekularen Wasserstoffbrücken-Ringen, wie durch X-Ray, 2D-NMR-, DFT-Methoden und Dipolmoment-Bestimmung gezeigt wird. Elektrochemische Experimente belegen eine elektronische Wechselwirkung der Eisenzentren. Die gemischt-valenten Verbindungen zeichnen sich durch IVCT-Banden im nahen Infrarot aus. Die elektronische Kopplungskonstante beträgt Hab ≈ 145-215 cm–1 für einen einzelnen FeII/FeIII-Übergang und belegt die Zugehörigkeit der Verbindungen zur Robin-Day-Klasse II. Im Festkörper sind die Valenzen gemäß Mößbauerspektren lokalisiert. Die vollständig oxidierten Verbindungen liegen nach DFT-Rechnungen nicht mehr in einer „Zick-Zack“-Struktur, sondern in einer gestreckten Konformation vor. Als Nebenprodukte bei der Amidkupplung werden die Anhydride SG-(Fca)2O (SG = Ac, Boc, Fmoc) isoliert. Diese zählen aufgrund des Fehlens einer IVCT-Bande zur Klasse I-II. Die ferrocenyloge Bfca wird in Form der N- und C-geschützten Bfca auf zwei Wegen synthetisiert. Schlüsselschritte stellen die Cu(II)-vermittelte Homokupplung bzw. die Pd-katalysierte Stille-Kupplung dar. Bfca und die amid- und harnstoffverknüpften Bis-Bfca-Verbindungen besitzen keine nachweisbare Vorzugskonformation in Lösung. Die gemischt-valenten Bfca-Kationen zeigen eine IVCT-Bande (Hab ≈ 300-600 cm–1) und gehören eher zur Klasse II-III. Die gemischt-valenten Verbindungen des als Nebenprodukt isolierten Tetraferrocenylstannans Sn[Fn(COOMe)4] (Fn = 1,1’-Ferrocenylen) mit einatomiger σ-Brücke zwischen den Ferroceneinheiten, zeigen IVCT-Banden im NIR-Spektrum und gehören somit zur Klasse II. Die elektronischen Kopplungen in Sn[Fn(COOMe)4]+/2+ betragen Hab ≈ 145 und 220 cm–1.

Synthese und Charakterisierung von zylindrischen Bürsten mit Polypeptidseitenketten

In der vorliegenden Arbeit konnte gezeigt werden, dass durch die grafting-from-Methode verschiedene geschützte Polypeptidbürsten basierend auf L-glutaminsäure, L-asparaginsäure, L-lysin und L-ornithin synthetisch zugänglich sind. Zur Verwirklichung dieser Synthesestrategie wurde mehrstufig ein Makroinitiator auf Basis von N-methacrylamid-1,6-diaminohexan hergestellt, der die ringöffnende Polymerisation von Leuchs´schen Anhydriden zur Entwicklung von geschützten Polypeptidseitenketten initiieren kann. Durch stark saure bzw. alkalische Abspaltbedingungen war es möglich, die Schutzgruppen bei allen geschützten Bürsten bis auf eine Spezies erfolgreich zu entfernen. Weitergehende Untersuchungen an den positiv bzw. negativ geladenen Polyelektrolytbürsten mittels statischer Lichtstreuung und Kapillarelektrophorese zeigten, dass lediglich die Z-geschützten Poly-L-lysinbürsten ohne Kettenabbau entschützt werden konnten. In allen anderen Fällen wurden nach Abspaltung der Schutzgruppen lineare Kettenfragmente detektiert. Durch die Zugabe von NaClO4 oder Methanol zu den wässrigen Lösungen der Poly-L-lysinbürsten konnte mittels CD-Spektroskopie gezeigt werden, dass die Seitenketten von einer ungeordneten Konformation in eine helikale Konformation übergehen. In weiterführenden Experimenten wurde mittels statischer Lichtstreuung, dynamischer Lichtstreuung, SAXS, und AFM-Aufnahmen in Lösung bewiesen, dass die helikale Konformation der Seitenketten eine deutliche Abnahme des Zylinderquerschnitts und des Querschnittträgheitsradius zur Folge hat, die Topologie der Bürste allerdings unverändert bleibt. Weiterhin konnte mittels Kapillarelektrophorese die elektrophoretische Mobilität der Poly-L-lysinbürsten und ihrer linearen Analoga bestimmt werden. Mit diesen Resultaten war es in Kombination mit statischen Lichtstreuexperimenten möglich, die effektive Ladung von linearem und verzweigten Poly-L-lysin nach einer Theorie von Muthukumar zu berechnen. Das Ergebnis dieser Rechnungen bestätigt die Ergebnisse früherer Untersuchungen von Peter Dziezok, der in seiner Dissertation durch Leitfähigkeits und Lichtstreumessungen an linearem PVP und PVP-Bürsten herausfand, dass die effektive Ladung von Polymerbürsten mindestens um einen Faktor 10 kleiner ist als bei den korrespondierenden linearen Analoga.

The synthesis of maleic anhydride: study of a new process and improvement of the industrial catalyst

Maleic anhydride is an important chemical intermediate mainly produced by the selective oxidation of n-butane, an industrial process catalyzed by vanadyl pyrophosphate-based materials, (VO)2P2O7. The first topic was investigated in collaboration with a company specialized in the production of organic anhydrides (Polynt SpA), with the aim of improving the performance of the process for the selective oxidation of n-butane to maleic anhydride, comparing the behavior of an industrial vanadyl pyrophosphate catalysts when utilized either in the industrial plant or in lab-scale reactor. The study was focused on how the catalyst characteristics and reactivity are affected by the reaction conditions and how the addition of a dopant can enhance the catalytic performance. Moreover, the ageing of the catalyst was studied, in order to correlate the deactivation process with the modifications occurring in the catalyst. The second topic was produced within the Seventh Framework (FP7) European Project “EuroBioRef”. The study was focused on a new route for the synthesis of maleic anhydride starting from an alternative reactant produced by fermentation of biomass:“bio-1-butanol”. In this field, the different possible catalytic configurations were investigated: the process was divided into two main reactions, the dehydration of 1-butanol to butenes and the selective oxidation of butenes to maleic anhydride. The features needed to catalyze the two steps were analyzed and different materials were proposed as catalysts, namely Keggin-type polyoxometalates, VOPO4∙2H2O and (VO)2P2O7. The reactivity of 1-butanol was tested under different conditions, in order to optimize the performance and understand the nature of the interaction between the alcohol and the catalyst surface. Then, the key intermediates in the mechanism of 1-butanol oxidehydration to MA were studied, with the aim of understanding the possible reaction mechanism. Lastly, the reactivity of the chemically sourced 1-butanol was compared with that one of different types of bio-butanols produced by biomass fermentation.

Synthese und Charakterisierung von zylindrischen Bürsten mit polypept(o)idischen Seitenketten als nanopartikuläre Trägersysteme

Zylindrische Polymerbürsten mit pept(o)idischen Seitenketten sind auf Grund ihrer elongierten Topologie, Bioverträglichkeit und hohen Dichte an funktionellen Gruppen vielversprechende Kandidaten für Anwendungen im Bereich des kontrollierten Wirkstoff- bzw. Gentransportes.In dieser Arbeit wurden Polylysin und Polysarkosin als Bestandteile der Seitenketten verwendet. Polylysin dient als positiv geladener Polypeptidblock für die Komplexierung von Polynukleotiden. Polysarkosin reduziert mit seinem „Stealth“-Effekt die Toxizität des Trägersystems und vermindert Wechselwirkungen mit dem Immunsystem. Über den „grafting from“-Ansatz und mit Hilfe der ringöffnenden NCA-Polymerisation konnten erstmals zylindrische Bürsten mit reinen Polysarkosin-Seitenketten sowie mit amphiphilen Seitenketten aus einem Polylysinkern und einer Polysarkosinschale hergestellt werden. Die Bürsten wurden mittels Lichtstreuung, GPC, CD-Spektroskopie und AFM charakterisiert. Die hohe Biokompatibilität beider Bürsten konnte durch Toxizitätstests und dynamische Lichtstreuung in humanem Blutserum nachgewiesen werden.Die Polysarkosin-Bürsten konnten zusätzlich an den Seitenkettenenden mit Azidgruppen funktionalisiert werden, welche eine effektive Biokonjugation ermöglichen. Die zylindrischen Bürsten zeigten nach ihrer Modifikation keine unspezifische Aufnahme in dendritische Zellen und könnten somit als Ausgangssubstanzen für die Synthese polymerbasierter Antikörper-Antigen-Konjugate in der Krebsimmuntherapie verwendet werden.Die Kern-Schale-Bürsten konnten erfolgreich mit siRNA komplexiert werden, ohne dass dabei eine Aggregation auftrat. In ersten Gen-Knockdown-Experimenten zeigten ihre Komplexe eine signifikante Verminderung der ApoB100-Proteinexpression in AML-12 Hepatozyten und könnten daher zukünftig als Transfektionsmittel in der Gentherapie ihren Einsatz finden.

Phosphate forms an unusual tripodal complex with the Fe-Mn center of sweet potato purple acid phosphatase

Purple acid phosphatases (PAPs) are a family of binuclear metalloenzymes that catalyze the hydrolysis of phosphoric acid esters and anhydrides. A PAP in sweet potato has a unique, strongly antiferromagnetically coupled Fe(III)-Mn(II) center and is distinguished from other PAPs by its increased catalytic efficiency for a range of activated and unactivated phosphate esters, its strict requirement for Mn(II), and the presence of a mu-oxo bridge at pH 4.90. This enzyme displays maximum catalytic efficiency (k(cat)/K-m) at pH 4.5, whereas its catalytic rate constant (k(cat)) is maximal at near-neutral pH, and, in contrast to other PAPs, its catalytic parameters are not dependent on the pK(a) of the leaving group. The crystal structure of the phosphate-bound Fe(III)-Mn(II) PAP has been determined to 2.5-Angstrom resolution (final R-free value of 0.256). Structural comparisons of the active site of sweet potato, red kidney bean, and mammalian PAPs show several amino acid substitutions in the sweet potato enzyme that can account for its increased catalytic efficiency. The phosphate molecule binds in an unusual tripodal mode to the two metal ions, with two of the phosphate oxygen atoms binding to Fe(III) and Mn(II), a third oxygen atom bridging the two metal ions, and the fourth oxygen pointing toward the substrate binding pocket. This binding mode is unique among the known structures in this family but is reminiscent of phosphate binding to urease and of sulfate binding to A protein phosphatase. The structure and kinetics support the hypothesis that the bridging oxygen atom initiates hydrolysis.