Degradação fotocatalítica do fungicida tebuconazole em solução aquosa

The tebuconazole photocatalytic degradation kinetics was studied in a batch reactor using TiO2 (P25-Degussa) as catalyst and a high pressure mercury lamp. The photolysis, adsorption and irradiation effects in the reaction rate were evaluated. Afterward, the suspension catalyst concentration and initial pH to the maximum reaction rate was determined. It was observed that the reaction rate can be approached by a pseudo-first order, with a maximum kinetics constant at 260 mg L-1catalyst concentration and pH 7.7.

Reator de UV-Ozônio com lâmpada a vapor de mercúrio a alta pressão modificada para tratamento superficial de óxidos transparentes condutivos utilizados em dispositivos poliméricos eletroluminescentes

An UV-Ozone reactor was developed with an ignition tube extracted into HID mercury lamp used to irradiation on zinc oxide (ZnO) and fluorinated tin oxide (FTO) films for PLEDs devices. Different exposures times were used. In contact angle measurements revealed better results for ZnO and FTO by 15 and 5 min, respectively. In Diffuse Reflectance Infra-red Fourier Transformed (DRIFT) spectroscopy allowed the observation of water, hydrocarbon and carbon dioxide adsorbed on the untreated TCO surfaces. After the UV-Ozone treatment the contaminants were significantly reduced or eliminated and the PLEDs devices decreased threshold voltages in comparison with respectively untreated TCOs.

Pienloistelamppujen johtuvat RF-häiriöt verrattuna CISPR 15 - standardin raja-arvoihin

Hehkulamput tullaan kieltämään Euroopan Unionin alueella vuoden 2016 syyskuuhun mennessä. Hehkulamput korvataan suurimmaksi osaksi pienloistelampuilla, jotka omaavat hehkulamppuihin verrattuna paremman hyötysuhteen. Pienloistelamput aiheuttavat kuitenkin häiriöitä niitä syöttävään sähköverkkoon. Tässä kandidaatin työssä mitattiin 15 erilaisen pienloistelampun aiheuttamat johtuvat RF-taajuiset häiriöt. Tuloksia verrattiin CISPR 15 – standardissa esitettyihin raja-arvoihin, joita pienloistelamppujen tulisi noudattaa. Mittaukset suoritettiin käyttämällä CISPR 16 –standardin kanssa yhteensopivaa mittavastaanotinta (Rohde & Schwarz ESHS30) sekä myöskin CISPR 16 yhteensopivaa keinoverkkoa (Rohde & Schwarz ESH2Z5). Lamput mitattiin CISPR 15 –standardin mukaisesti, muutamia poikkeuksia lukuun ottamatta. Lamppuja ei mitattu käyttämällä CISPR 15 –standardissa vaadittua lampun pidintä. Eikä lamppuja myöskään esikäytetty ollenkaan. Lukuun ottamatta yhtä pienloistelamppua, kaikki jäivät raja-arvon alapuolelle. Rajan ylittäneen lampun tulos tosin mahtuu mittavastaanottimen mittavirheeseen. Joten kyseessä ei ollut suuren suuri ylitys. Muiden tutkittujen pienloistelamppujen johtuvat RF-häiriöt ovat hyväksyttävällä tasolla ja ne tuskin tulevat aiheuttamaan ongelmia.

Led -tekniikan käyttöönotto polyakryyliamidin valmistuksessa fotoinitiaatioprosessissa

Työssä tutkittiin Kemira Chemicals Oy:n Vaasan polyelektrolyyttitehtaalla led -tekniikan käyttöönottoa polyakryyliamidin valmistamisessa fotoinitiaatiolla. Led- tekniikan käyttöönoton seuraamisella ja erilaisten mittausten tekemisellä oli tarkoitus saada uudesta teknologiasta tietoa, jonka perusteella tulevaisuuden investointiesitykset voisivat olla paremmin perusteltavissa. Työn kirjallisuusosassa käytiin läpi valaistus- ja led -tekniikan perusteita sekä polymeerien perusteita. Lisäksi polyelektrolyyttien ominaisuudet ja käyttökohteet käytiin läpi. Kirjallisuusosan lopussa käytiin läpi polymerointia, fotoinitiaatiota ja vapaiden radikaalien toimintaa. Myös kustannuslaskentaa selvitettiin. Mittausten ja vertailujen perusteella voitiin todeta led -valojen vaikuttaneen positiivisesti prosessin toimintaan ja lopputuotteiden laatuun. Tämänlaisessa sovelluksessa led -tekniikka ei ole kuitenkaan vielä kilpailukykyistä vanhaan teknologiaan verrattuna puhtaasti taloudellisesti ajateltuna.

Technical and economic analysis of replacing artificial lighting system to induction of photoperiod effect in begonia's seedlings in greenhouse

The type of artificial light used for inducing photoperiod effect in begonia's seedlings at greenhouse has fundamental importance in the growth and development of these plants and directly reflects in the electrical energy consumption used in this production process. The objective of this research was to analyze the technical and economic feasibility of replacing the current technology of artificial lighting used by the producers (incandescent lamps), by the technology of discharge lamps with the purpose of inducing photoperiod in a greenhouse. The analysis results indicate that the discharge lamp of 32 W Tubular Fluorescent discharge lamp was the one that presented the lower peak demand and lower average energy consumption of 85.01% compared to incandescent filament lamp of 100 W that is the technology of bigger consumption and currently used by the producer.

Technical-economic analysis of different lighting systems for broiler poultry

ABSTRACT Broiler poultry is highly dependent on artificial lightening. Power consumption costs of artificial lighting systems is the second largest expense related to broiler industry, second only to feed expenses. Therefore, the current study focused to analyze technical and economic feasibility of replacing incandescent lamps already used in aviaries with other lamp types. Costs related to power consumption, implementation and maintenance of the lighting systems were evaluated with the aid of financial mathematics using net present value, return over investment and payback. Systems composed of six lamp types were analyzed in two different configurations to meet the minimum illuminance of 5 and 20 lux and for use in conventional sheds and dark house. The lamps tested were incandescent (LI) of 100 W, compact fluorescent (CFL) of 34 W, mixed (ML) 160 W sodium vapor (SVL) of 70 W, tubular fluorescent T8 (TFL T8) of 40 W and tubular fluorescent T5 (TFL T5) of 28 W. For the systems tested, it was found that the tubular fluorescent lamps T8 and T5 showed the best results of technical and economic feasibility.

Energiansäästölamppujen vaikutukset pienjännitteisen sähkönjakeluverkon kuormitukseen ja häviöihin

Euroopan Unioni kieltää matalan hyötysuhteen lamppujen käyttämisen sekä sisä- että ulkovalaisimissa. Näin ollen matalan hyötysuhteen lamput, kuten perinteiset hehkulamput tulee vaihtaa paremman hyötysuhteen lamppuihin, kuten energiansäästölamppuihin. Energiansäästölampuissa 230 V, 50 Hz verkkosähkö muunnetaan valonlähteelle sopivaksi tehoelektroniikan avulla. 50 Hz perustaajuisen virran lisäksi energiansäästölamput ottavat verkosta harmonisia yliaaltoja. Harmoniset yliaallot aiheuttavat lisähäviöitä verkostokomponenteissa, kuten muuntajissa ja johdoissa. Tässä kandidaatintyössä tutkitaan millaisia vaikutuksia hehkulamppujen vaihtaminen energiansäästölamppuihin aiheuttaa pienjännitteisessä jakeluverkossa. Työssä tarkastellaan lyhyesti myös energiansäästölamppujen energiatehokkuutta, sekä sitä, millaisia rajoitteita standardit asettavat harmonisille yliaalloille.

Jeg strikker, derfor er jeg! : læring og identitet i uformelle læringsrum

The dissertation ´I knit, therefore I am!´ Learning and identity in informal space has two main purposes. The first purpose being an investigation of how new value attributions and thinking can generate novel and usable knowledge to the field of craftsmanship, and the second purpose being a display of a different and overlooked philosophical and cultural potential in a reflexive mode of expression, which is able to reflect the normative comprehension of craftsmanship. The dissertation focuses on learning and identity in informal spaces of learning and how it is possible to relate such a learning perspective to crafts training in educational establishments. The empirical foundation of this dissertation is ‘craftivism’. In the dissertation activists from the Nordic countries have been interviewed about what they do when they put up their textile graffiti on lamp posts and house walls. Three research problems are presented: 1) What stories do people who work as crafts activists, tell about ways of relating and methods of action when they make crafts? 2) What do these stories tell about learning and identity? 3) How may the research results influence training and education in craftsmanship? These questions are being asked in order to acquire new knowledge in two aspects; first aspect being knowledge about crafts in relation to techniques, tradition and the objects in crafts, and the second aspect being knowledge about learning and identity in informal spaces of learning. The dissertations theoretical foundation is post structural and sociocultural combined with hermeneutical-inspired qualitative interviews. The author’s position and pre-understanding is subject to discussion in relation to the informant; the performing activist, as the background for both of them is craftsmanship. Starting from cultural studies, it is possible to see the activist subject’s conditions of possibilities in the culture, as the activism of the sub-cultural phenomenon’s craft lights up through a performing approach to the individual’s actions. First the research material has been analysed for events of textile graffiti and possible themes in the events, after which the results have been summarised. Next the research material has been analysed for events about learning and identity due to the author’s wish of comprehending the background of and motivational force in activism. The analysis is divided in main perspectives with different dimensions. The results of the analysis show the activist subject’s construction of an individual who actively takes part in a community by e.g. creating joy, changing the world’s perception of sustainability or by feminizing the public space. By taking crafts over the borders (and away from the class room) crafts become contextualized in a novel fashion thus obtaining an independent status. In this fashion the dissertation writes itself into a new method of comprehending and performing traditional craftsmanship techniques.

Hydrometallurgical recovery of valuable metals from secondary raw materials

Wastes and side streams in the mining industry and different anthropogenic wastes often contain valuable metals in such concentrations their recovery may be economically viable. These raw materials are collectively called secondary raw materials. The recovery of metals from these materials is also environmentally favorable, since many of the metals, for example heavy metals, are hazardous to the environment. This has been noticed in legislative bodies, and strict regulations for handling both mining and anthropogenic wastes have been developed, mainly in the last decade. In the mining and metallurgy industry, important secondary raw materials include, for example, steelmaking dusts (recoverable metals e.g. Zn and Mo), zinc plant residues (Ag, Au, Ga, Ge, In) and waste slurry from Bayer process alumina production (Ga, REE, Ti, V). From anthropogenic wastes, waste electrical and electronic equipment (WEEE), among them LCD screens and fluorescent lamps, are clearly the most important from a metals recovery point of view. Metals that are commonly recovered from WEEE include, for example, Ag, Au, Cu, Pd and Pt. In LCD screens indium, and in fluorescent lamps, REEs, are possible target metals. Hydrometallurgical processing routes are highly suitable for the treatment of complex and/or low grade raw materials, as secondary raw materials often are. These solid or liquid raw materials often contain large amounts of base metals, for example. Thus, in order to recover valuable metals, with small concentrations, highly selective separation methods, such as hydrometallurgical routes, are needed. In addition, hydrometallurgical processes are also seen as more environmental friendly, and they have lower energy consumption, when compared to pyrometallurgical processes. In this thesis, solvent extraction and ion exchange are the most important hydrometallurgical separation methods studied. Solvent extraction is a mainstream unit operation in the metallurgical industry for all kinds of metals, but for ion exchange, practical applications are not as widespread. However, ion exchange is known to be particularly suitable for dilute feed solutions and complex separation tasks, which makes it a viable option, especially for processing secondary raw materials. Recovering valuable metals was studied with five different raw materials, which included liquid and solid side streams from metallurgical industries and WEEE. Recovery of high purity (99.7%) In, from LCD screens, was achieved by leaching with H2SO4, extracting In and Sn to D2EHPA, and selectively stripping In to HCl. In was also concentrated in the solvent extraction stage from 44 mg/L to 6.5 g/L. Ge was recovered as a side product from two different base metal process liquors with Nmethylglucamine functional chelating ion exchange resin (IRA-743). Based on equilibrium and dynamic modeling, a mechanism for this moderately complex adsorption process was suggested. Eu and Y were leached with high yields (91 and 83%) by 2 M H2SO4 from a fluorescent lamp precipitate of waste treatment plant. The waste also contained significant amounts of other REEs such as Gd and Tb, but these were not leached with common mineral acids in ambient conditions. Zn was selectively leached over Fe from steelmaking dusts with a controlled acidic leaching method, in which the pH did not go below, but was held close as possible to, 3. Mo was also present in the other studied dust, and was leached with pure water more effectively than with the acidic methods. Good yield and selectivity in the solvent extraction of Zn was achieved by D2EHPA. However, Fe needs to be eliminated in advance, either by the controlled leaching method or, for example, by precipitation. 100% Pure Mo/Cr product was achieved with quaternary ammonium salt (Aliquat 336) directly from the water leachate, without pH adjustment (pH 13.7). A Mo/Cr mixture was also obtained from H2SO4 leachates with hydroxyoxime LIX 84-I and trioctylamine (TOA), but the purities were 70% at most. However with Aliquat 336, again an over 99% pure mixture was obtained. High selectivity for Mo over Cr was not achieved with any of the studied reagents. Ag-NaCl solution was purified from divalent impurity metals by aminomethylphosphonium functional Lewatit TP-260 ion exchange resin. A novel preconditioning method, named controlled partial neutralization, with conjugate bases of weak organic acids, was used to control the pH in the column to avoid capacity losses or precipitations. Counter-current SMB was shown to be a better process configuration than either batch column operation or the cross-current operation conventionally used in the metallurgical industry. The raw materials used in this thesis were also evaluated from an economic point of view, and the precipitate from a waste fluorescent lamp treatment process was clearly shown to be the most promising.

Computational studies for the design of process equipment with complex geometries

This study combines several projects related to the flows in vessels with complex shapes representing different chemical apparata. Three major cases were studied. The first one is a two-phase plate reactor with a complex structure of intersecting micro channels engraved on one plate which is covered by another plain plate. The second case is a tubular microreactor, consisting of two subcases. The first subcase is a multi-channel two-component commercial micromixer (slit interdigital) used to mix two liquid reagents before they enter the reactor. The second subcase is a micro-tube, where the distribution of the heat generated by the reaction was studied. The third case is a conventionally packed column. However, flow, reactions or mass transfer were not modeled. Instead, the research focused on how to describe mathematically the realistic geometry of the column packing, which is rather random and can not be created using conventional computeraided design or engineering (CAD/CAE) methods. Several modeling approaches were used to describe the performance of the processes in the considered vessels. Computational fluid dynamics (CFD) was used to describe the details of the flow in the plate microreactor and micromixer. A space-averaged mass transfer model based on Fick’s law was used to describe the exchange of the species through the gas-liquid interface in the microreactor. This model utilized data, namely the values of the interfacial area, obtained by the corresponding CFD model. A common heat transfer model was used to find the heat distribution in the micro-tube. To generate the column packing, an additional multibody dynamic model was implemented. Auxiliary simulation was carried out to determine the position and orientation of every packing element in the column. This data was then exported into a CAD system to generate desirable geometry, which could further be used for CFD simulations. The results demonstrated that the CFD model of the microreactor could predict the flow pattern well enough and agreed with experiments. The mass transfer model allowed to estimate the mass transfer coefficient. Modeling for the second case showed that the flow in the micromixer and the heat transfer in the tube could be excluded from the larger model which describes the chemical kinetics in the reactor. Results of the third case demonstrated that the auxiliary simulation could successfully generate complex random packing not only for the column but also for other similar cases.

Determination of macromolecular exchange and PO2 in the microcirculation: a simple system for in vivo fluorescence and phosphorescence videomicroscopy

We have developed a system with two epi-illumination sources, a DC-regulated lamp for transillumination and mechanical switches for rapid shift of illumination and detection of defined areas (250-750 µm²) by fluorescence and phosphorescence videomicroscopy. The system permits investigation of standard microvascular parameters, vascular permeability as well as intra- and extravascular PO2 by phosphorescence quenching of Pd-meso-tetra (4-carboxyphenyl) porphine (PORPH). A Pechan prism was used to position a defined region over the photomultiplier and TV camera. In order to validate the system for in vivo use, in vitro tests were performed with probes at concentrations that can be found in microvascular studies. Extensive in vitro evaluations were performed by filling glass capillaries with solutions of various concentrations of FITC-dextran (diluted in blood and in saline) mixed with different amounts of PORPH. Fluorescence intensity and phosphorescence decay were determined for each mixture. FITC-dextran solutions without PORPH and PORPH solutions without FITC-dextran were used as references. Phosphorescence decay curves were relatively unaffected by the presence of FITC-dextran at all concentrations tested (0.1 µg/ml to 5 mg/ml). Likewise, fluorescence determinations were performed in the presence of PORPH (0.05 to 0.5 mg/ml). The system was successfully used to study macromolecular extravasation and PO2 in the rat mesentery circulation under controlled conditions and during ischemia-reperfusion.

Sähkön laadun tutkimus hypermarketin pysäköintihallin valaistustekniikkamuutoksessa

Talotekniikan alalla valaistusmuutoksissa LED-valaistus on nykypäivää. Valaistuksen käyttöominaisuudet ja hyödyt tekevät siitä perustellun valinnan myös suurissa kohteissa. Näistä laajemmista valaistuksen muutoksista ja niiden vaikutuksista sähkön laatuun ei ole yleisesti mittaustietoa. Tämä tutkimus perustui sähkön laadun käytännön mittauksiin valaistusmuutoksessa, jossa elohopeahöyrylampuilla toteutettu valaistus vaihdettiin LED-valaistukseen hypermarketin pysäköintihallissa. Valaistusjärjestelmän muutoksen vaikutusta sähkön laatuun tutkittiin vertailemalla mittaustuloksia vanhan ja uuden järjestelmän välillä. Tutkimuksen tarkoituksena oli osoittaa miten LED-valaistukseen siirtyminen vaikuttaa sähkön laatuun valitussa tutkimuskohteessa. Tutkimuksessa tuotettu tieto on hyödynnettävissä vastaavissa kohteissa LED-valaistukseen siirryttäessä sekä valaistuksen käyttöönoton suunnittelussa ja toteuttamisessa. Tutkimuksen tuloksia voidaan hyödyntää myös kustannusten arvioimisessa valaistavan tilan sähkönkulutuksen osalta. Tutkimus toteutettiin käyttämällä triangulaatiomenetelmää eli teemahaastattelulla, kirjallisuuskatsauksella ja käytännön mittauksilla. Näiden menetelmien tulokset tukivat tutkimukselle asetettuja hypoteeseja. Valitulla tutkimusmenetelmällä saatiin selville, että LED-valaistukseen siirtymisellä ei ollut heikentäviä vaikutuksia sähkön laatuun tutkitun kohteen valaistusjärjestelmässä. Toisaalta positiivisina vaikutuksina huomioitiin muun muassa merkittävä energian säästö, virran harmonisten häiriöiden väheneminen sekä kokonaistehokertoimen parantuminen.

Long-term loss of color vision after exposure to mercury vapor

We evaluated the color vision of 24 subjects (41.6 ± 6.5 years; 6 females) who worked in fluorescent lamp industries. They had been occupationally exposed to mercury vapor (10.6 ± 5.2 years) and had been away from the source of exposure for 6.4 ± 4.04 years. Mean urinary concentration of mercury was 40.6 ± 36.4 µg/g creatinine during or up to 1 year after exposure and 2.71 ± 1.19 µg/g creatinine at the time of color vision testing or up to 1 year thereafter. All patients were diagnosed with chronic mercury intoxication, characterized by clinical symptoms and neuropsychological alterations. A control group (N = 36, 48.6 ± 11.9 years, 10 females, 1.5 ± 0.47 µg mercury/g creatinine) was subjected to the same tests. Inclusion criteria for both groups were Snellen VA 20/30 or better and absence of known ophthalmologic pathologies. Color discrimination was assessed with the Farnsworth D-15 test (D-15) and with the Lanthony D-15d test (D-15d). Significant differences were found between the two eyes of the patients (P < 0.001) in both tests. Results for the worst eye were also different from controls for both tests: P = 0.014 for D-15 and P < 0.001 for D-15d. As shown in previous studies, the D-15d proved to be more sensitive than the D-15 for the screening and diagnosis of the color discrimination losses. Since color discrimination losses were still present many years after the end of exposure, they may be considered to be irreversible, at least under the conditions of the present study.

Neuropsychological dysfunction related to earlier occupational exposure to mercury vapor

We assessed the neuropsychological test performances of 26 patients (mean age = 41.5 ± 6.1 years; mean years of education = 9.8 ± 1.8; 20 males) diagnosed with chronic occupational mercurialism who were former workers at a fluorescent lamp factory. They had been exposed to elemental mercury for an average of 10.2 ± 3.8 years and had been away from this work for 6 ± 4.7 years. Mean urinary mercury concentrations 1 year after cessation of work were 1.8 ± 0.9 µg/g creatinine. Twenty control subjects matched for age, gender, and education (18 males) were used for comparison. Neuropsychological assessment included attention, inhibitory control, verbal and visual memory, verbal fluency, manual dexterity, visual-spatial function, executive function, and semantic knowledge tests. The Beck Depression Inventory and the State and Trait Inventory were used to assess depression and anxiety symptoms, respectively. The raw score for the group exposed to mercury indicated slower information processing speed, inferior performance in psychomotor speed, verbal spontaneous recall memory, and manual dexterity of the dominant hand and non-dominant hand (P < 0.05). In addition, the patients showed increased depression and anxiety symptoms (P < 0.001). A statistically significant correlation (Pearson) was demonstrable between mean urinary mercury and anxiety trait (r = 0.75, P = 0.03). The neuropsychological performances of the former workers suggest that occupational exposure to elemental mercury has long-term effects on information processing and psychomotor function, with increased depression and anxiety also possibly reflecting the psychosocial context.

Methodological approaches to planar and volumetric scintigraphic imaging of small volume targets with high spatial resolution and sensitivity

Single-photon emission computed tomography (SPECT) is a non-invasive imaging technique, which provides information reporting the functional states of tissues. SPECT imaging has been used as a diagnostic tool in several human disorders and can be used in animal models of diseases for physiopathological, genomic and drug discovery studies. However, most of the experimental models used in research involve rodents, which are at least one order of magnitude smaller in linear dimensions than man. Consequently, images of targets obtained with conventional gamma-cameras and collimators have poor spatial resolution and statistical quality. We review the methodological approaches developed in recent years in order to obtain images of small targets with good spatial resolution and sensitivity. Multipinhole, coded mask- and slit-based collimators are presented as alternative approaches to improve image quality. In combination with appropriate decoding algorithms, these collimators permit a significant reduction of the time needed to register the projections used to make 3-D representations of the volumetric distribution of target’s radiotracers. Simultaneously, they can be used to minimize artifacts and blurring arising when single pinhole collimators are used. Representation images are presented, which illustrate the use of these collimators. We also comment on the use of coded masks to attain tomographic resolution with a single projection, as discussed by some investigators since their introduction to obtain near-field images. We conclude this review by showing that the use of appropriate hardware and software tools adapted to conventional gamma-cameras can be of great help in obtaining relevant functional information in experiments using small animals.