Techniques for determining bias and stability in satellite altimeters

The case for monitoring large-scale sea level variability is established in the context of the estimation of the extent of anthropogenic climate change. Satellite altimeters are identified as having the potential to monitor this change with high resolution and accuracy. Possible sources of systematic errors and instabilities in these instruments which would be hurdles to the most accurate monitoring of such ocean signals are examined. Techniques for employing tide gauges to combat such inaccuracies are proposed and developed. The tide gauge at Newhaven in Sussex is used in conjunction with the nearby satellite laser ranger and high-resolution ocean models to estimate the absolute bias of the TOPEX, Poseidon, ERS 1 and ERS 2 altimeters. The theory which underlies the augmentation of altimeter measurements with tide gauge data is developed. In order to apply this, the tide gauges of the World Ocean Circulation Experiment are assessed and their suitability for altimeter calibration is determined. A reliable subset of these gauges is derived. A method of intra-altimeter calibration is developed using these tide gauges to remove the effect of variability over long time scales. In this way the long-term instability in the TOPEX range measurement is inferred and the drift arising from the on-board ultra stable oscillator is thus detected. An extension to this work develops a method for inter-altimeter calibration, allowing the systematic differences between unconnected altimeters to be measured. This is applied to the TOPEX and ERS 1 altimeters.

The use of Meteosat satellite data for spatial rainfall estimations and hydrological simulations

Satellite information, in combination with conventional point source measurements, can be a valuable source of information. This thesis is devoted to the spatial estimation of areal rainfall over a region using both the measurements from a dense and sparse network of rain-gauges and images from the meteorological satellites. A primary concern is to study the effects of such satellite assisted rainfall estimates on the performance of rainfall-runoff models. Low-cost image processing systems and peripherals are used to process and manipulate the data. Both secondary as well as primary satellite images were used for analysis. The secondary data was obtained from the in-house satellite receiver and the primary data was obtained from an outside source. Ground truth data was obtained from the local Water Authority. A number of algorithms are presented that combine the satellite and conventional data sources to produce areal rainfall estimates and the results are compared with some of the more traditional methodologies. The results indicate that the satellite cloud information is valuable in the assessment of the spatial distribution of areal rainfall, for both half-hourly as well as daily estimates of rainfall. It is also demonstrated how the performance of the simple multiple regression rainfall-runoff model is improved when satellite cloud information is used as a separate input in addition to rainfall estimates from conventional means. The use of low-cost equipment, from image processing systems to satellite imagery, makes it possible for developing countries to introduce such systems in areas where the benefits are greatest.

Distributive tactile sensing using fibre Bragg grating sensors

Two distributive tactile sensing systems are presented, based on fibre Bragg grating sensors. The first is a onedimensional metal strip with an array of 4 sensors, which is capable of detecting the magnitude and position of a contacting load. This system is compared experimentally with a similar system using resistive strain gauges. The second is a two-dimensional steel plate with 9 sensors which is able to distinguish the position and shape of a contacting load. This system is compared with a similar system using 16 infrared displacement sensors. Each system uses neural networks to process the sensor data to give information concerning the type of contact.

A study of the properties and applications of electrostatic charged particle oscillators

This investigation originated from work by Dr. A.H. McIlraith of the National Physical Laboratory who, in 1966, described a new type of charged particle oscillator. This makes use of two equal cylindrical electrodes to constrain the particles in such a way that they follow extremely long oscillatory paths between the electrodes under the influence of an electrostatic field alone. The object of this work has been to study the principle of the oscillator in detail and to investigate its properties and applications. Any device which is capable of creating long electron trajectories has potential application in the field of ultra high vacuum technology. It was therefore considered that a critical review of the problems associated with the production and measurement of ultra high vacuum was relevant in the initial stages of the work. The oscillator has been applied with a considerable degree of success as a high energy electrostatic ion source. This offers several advantages over existing ion sources. It can be operated at much lower pressures without the need of a magnetic field. The oscillator principle has also been applied as a thermionic ionization gauge and has been compared with other ionization gauges to pressures as low as 5 x 10- 11 torr.. This new gauge exhibited a number of advantages over most of the existing gauges. Finally the oscillator has been used in an evaporation ion pump and has exhibited fairly high pumping speeds for argon gas relative to those for nitrogen. This investigation supports the original work of Dr. A.H. McIlraith and shows that his proposed oscillator has considerable potential in the fields of vacuum technology and electron physics.

Fibre Bragg grating sensors for distributive tactile sensing

Distributive tactile sensing is a method of tactile sensing in which a small number of sensors monitors the behaviour of a flexible substrate which is in contact with the object being sensed. This paper describes the first use of fibre Bragg grating sensors in such a system. Two systems are presented: the first is a one-dimensional metal strip with an array of four sensors, which is capable of detecting the magnitude and position of a contacting load. This system is favourably compared experimentally with a similar system using resistive strain gauges. The second system is a two-dimensional steel plate with nine sensors which is able to distinguish the position and shape of a contacting load, or the positions of two loads simultaneously. This system is compared with a similar system using 16 infrared displacement sensors. Each system uses neural networks to process the sensor data to give information concerning the type of contact. Issues and limitations of the systems are discussed, along with proposed solutions to some of the difficulties. © 2007 IOP Publishing Ltd.

Tunnel monitoring using multicore displacement sensor

In this paper, we report the first demonstration of multiplexed fibre Bragg grating strain sensors in a multicore fibre for shape measurement and their application to structural monitoring. Sets of gratings, acting as strain gauges, are co-located in the multicore fibre such that they enable the curvature to be determined via differential strain measurement. Multiple sets of these gratings allow the curvature to be measured at several points along the fibre. In this paper, the multicore fibre is configured to measure the deflection of a simple mechanical beam arising from the displacement of concrete tunnel sections. Laboratory tests are presented in which the system was demonstrated capable of displacement measurement with a resolution of ±0.1 mm over a range of several millimetres. © 2006 IOP Publishing Ltd.

Distributive tactile sensing using fibre bragg grating sensors

Two distributive tactile sensing systems are presented, based on fibre Bragg grating sensors. The first is a one-dimensional metal strip with an array of 4 sensors, which is capable of detecting the magnitude and position of a contacting load. This system is compared experimentally with a similar system using resistive strain gauges. The second is a two-dimensional steel plate with 9 sensors which is able to distinguish the position and shape of a contacting load. This system is compared with a similar system using 16 infrared displacement sensors. Each system uses neural networks to process the sensor data to give information concerning the type of contact.

Two-axis bend measurement with Bragg gratings in multicore optica fibre

We describe what is to our knowledge the first use of fiber Bragg gratings written into three separate cores of a multicore fiber for two-axis curvature measurement. The gratings act as independent, but isothermal, fiber strain gauges for which local curvature determines the difference in strain between cores, permitting temperature-independent bend measurement.

A Kraft-index – kreatív városok – fenntartható vidék (The KRAFT Index: Creative Cities – Sustainable Regions)

A KRAFT-index: Kreatív városok – fenntartható vidék egy komplex mutatórendszer, amely a fejlődési tendenciát, hálózatosodást, a fontosabb szereplők együttműködési készségét és kapacitását, kreativitási potenciálját, valamint a szereplők szinergiáiból fakadó belső energiákat és lehetőségeiket jelzi. A város- és vidékfejlesztés sikerének zálogaként előtérbe állítja és méri az ún. „puha” tényezőket, úgymint a kreativitást, innovációs képességet, új tudás létrehozását, tudástranszfert, együttműködési készséget, bizalmat, kollektív kompetenciákat. A társadalmi, gazdasági és tudományos kapcsolatok és hálózatok sűrűsége, minősége és dinamizmusa a sikeres fejlődés és fejlesztés kulcsai: ezek ma már fontosabb tényezők, mint a fizikai távolság, az adminisztratív jogi határok vagy az ún. „kemény” indikátorok. Az index értékeli egy térség lehetőségeit arra, hogy az ott élők, dolgozók, alkotók és letelepedni kívánók életminőségét, a vállalatok minőségi munkaerő iránti igényét és a fenntarthatósági szempontokat egyaránt figyelembe véve fejlessze gazdaságát és versenyképességét. Három tulajdonságcsoportot mér: 1. kreativitiási és innovációs potenciál, az új tudás létrehozásának képessége, 2. társadalmi és kapcsolati tőke, hálózati potenciál és „összekapcsoltság”, valamint 3. fenntarthatósági potenciál. _____ The KRAFT Index: Creative Cities – Sustainable Regions is a complex indicator system to measure development tendencies, ‘networkedness’, cooperation inclination and capacity, creativity potential and possibilities arising from the synergies among actors. It highlights and gauges ‘soft’ factors, such as creativity, innovation capacity, knowledge production, knowledge transfer, willingness for cooperation, trust, and collective competences and perceives effective regional cooperation among economic and social actors as the measure of successful urban and rural development. The density, quality and dynamism of social, economic and academic networks are more important factors than physical distance, administrative legal barriers or ‘hard’ indicators. The index evaluates the potential of a region to develop its economy and competitiveness by considering the quality of life of its inhabitants, workers, producers and immigrants, the quality workforce requirements of companies and sustainability. It measures three groups of qualities: 1. creativity and innovation potential, the ability of knowledge production; 2. social and connection capital, network potential and connectedness; and 3. sustainability potential.

Study of carbon nanotube film and shape memory alloys treatment for sensing and structural vibration control

Structural vibration control is of great importance. Current active and passive vibration control strategies usually employ individual elements to fulfill this task, such as viscoelastic patches for providing damping, transducers for picking up signals and actuators for inputting actuating forces. The goal of this dissertation work is to design, manufacture, investigate and apply a new type of multifunctional composite material for structural vibration control. This new composite, which is based on multi-walled carbon nanotube (MWCNT) film, is potentially to function as free layer damping treatment and strain sensor simultaneously. That is, the new material integrates the transducer and the damping patch into one element. The multifunctional composite was prepared by sandwiching the MWCNT film between two adhesive layers. Static sensing test indicated that the MWCNT film sensor resistance changes almost linearly with the applied load. Sensor sensitivity factors were comparable to those of the foil strain gauges. Dynamic test indicated that the MWCNT film sensor can outperform the foil strain gage in high frequency ranges. Temperature test indicated the MWCNT sensor had good temperature stability over the range of 237 K-363 K. The Young’s modulus and shear modulus of the MWCNT film composite were acquired by nanoindentation test and direct shear test, respectively. A free vibration damping test indicated that the MWCNT composite sensor can also provide good damping without adding excessive weight to the base structure. A new model for sandwich structural vibration control was then proposed. In this new configuration, a cantilever beam covered with MWCNT composite on top and one layer of shape memory alloy (SMA) on the bottom was used to illustrate this concept. The MWCNT composite simultaneously serves as free layer damping and strain sensor, and the SMA acts as actuator. Simple on-off controller was designed for controlling the temperature of the SMA so as to control the SMA recovery stress as input and the system stiffness. Both free and forced vibrations were analyzed. Simulation work showed that this new configuration for sandwich structural vibration control was successful especially for low frequency system.

Challenge to Managers: Changing Hotel Work from a Secondary Choice to career Development

In his discussion - Challenge To Managers: Changing Hotel Work from a Secondary Choice to Career Development - by Leonidas Chitiris, Lecturer in Management, Piraeus Graduate School of Industrial Studies, Athens, Greece, Chitiris marginally alludes at the outset: “Surveys and interviews with hotel employees in Greece with regard to why individuals work for hotels and to what extent their rationale to join the hotel industry affects hotel productivity revealed that the choice to work in hotels is a secondary preference and reflects the opportunity structure in the economy at any given time and the greater the number of those who work in hotels when there are no other employment opportunities, the less likely the chances for overall improved performance. Given the increase in the proportion of unskilled, unmotivated workers, the level of hotel productivity consequently decreases! The author interprets the findings in terms of the economic and employment conditions in the Greek hotel industry. To enhance the rationale of his thesis statement, Chitiris offers with citation: “Research on initial entry into the labor force has shown that new employees reflect idealized expectations and are frequently not very satisfied with their jobs and roles in the work settings.” Chitiris advances the thought even further by saying: “Research on job satisfaction, motivation, and production purports that management can initiate policies that develop job satisfaction and may improve productivity.” The author outlines components within the general category of the hotel industry to label and quantify exactly why there may be a lag between employee expectations and the delivery of a superior level of service. Please keep in mind that the information for this essay is underpinned by the hotel industry in Greece, exclusively. Demographic information is provided. One example of the many factors parsed in this hotel service discussion is the employee/guest relationship. “The quality of service in hotels is affected to a great extent by the number of guests a hotel employee has to serve,” Chitiris offers. Additionally, Chitiris’ characterization of the typical hotel employee in Greece is not flattering, but it is an informed and representative view of that lodging labor pool. The description in and of itself begs to explain at least some of why the hotel industry in Greece suffers a consequently diminished capacity of superior service. Ill equipped, under-educated, over-worked, and under-paid are how Chitiris describes most employees in the Hellenist hospitality field. Survey based studies, and formulaic indices are used to measure variables related to productivity; the results may be inconclusive industry wide, but are interesting nonetheless. Also, an appealing table gauges the reasons why hotel workers actually employ themselves in the lodging industry. Chirtiris finds that salary expectations do not rate all that high on the motivational chart and are only marginal when related to productivity. In closing, Chirtiris presents a 5-phase development plan hotels should look to in improving performance and productivity at their respective properties.

Proposta de válvula bypass para controle de velocidade de PIGs instrumentados: protótipo e simulação em bancada

In the Oil industry, oil and gas pipelines are commonly utilized to perform the transportation of production fluids to longer distances. The maintenance of the pipelines passes through the analysis of several tools, in which the most currently used are the pipelines inspection cells, popularly knowing as PIG. Among the variants existing in the market, the instrumented PIG has a significant relevance; acknowledging that through the numerous sensors existing in the equipment, it can detect faults or potential failure along the inspected line. Despite its versatility, the instrumented PIG suffers from speed variations, impairing the reading of sensors embedded in it. Considering that PIG moves depending on the speed of the production fluid, a way to control his speed is to control the flow of the fluid through the pressure control, reducing the flow rate of the produced flow, resulting in reduction of overall production the fluid in the ducts own or with the use of a restrictive element (valve) installed on it. The characteristic of the flow rate/pressure drop from restrictive elements of the orifice plate is deducted usually from the ideal energy equation (Bernoulli’s equation) and later, the losses are corrected normally through experimental tests. Thus, with the objective of controlling the fluids flow passing through the PIG, a valve shutter actuated by solenoid has been developed. This configuration allows an ease control and stabilization of the flow adjustment, with a consequent response in the pressure drops between upstream and downstream of the restriction. It was assembled a test bench for better definition of flow coefficients; composed by a duct with intern diameter of four inches, one set of shutters arranged in a plate and pressure gauges for checking the pressure drop in the test. The line was pressurized and based on the pressure drop it was possible to draw a curve able to characterize the flow coefficient of the control valve prototype and simulate in mockup the functioning, resulting in PIG speed reduction of approximately 68%.

Development of an instrumented customizable total knee prosthesis for experimental tests.

Total knee arthroplasty (TKA) has revolutionized the life of millions of patients and it is the most efficient treatment in cases of osteoarthritis. The increase in life expectancy has lowered the average age of the patient, which requires a more enduring and performing prosthesis. To improve the design of implants and satisfying the patient's needs, a deep understanding of the knee Biomechanics is needed. To overcome the uncertainties of numerical models, recently instrumented knee prostheses are spreading. The aim of the thesis was to design and manifacture a new prototype of instrumented implant, able to measure kinetics and kinematics (in terms of medial and lateral forces and patellofemoral forces) of different interchangeable designs of prosthesis during experiments tests within a research laboratory, on robotic knee simulator. Unlike previous prototypes it was not aimed for industrial applications, but purely focusing on research. After a careful study of the literature, and a preliminary analytic study, the device was created modifying the structure of a commercial prosthesis and transforming it in a load cell. For monitoring the kinematics of the femoral component a three-layers, piezoelettric position sensor was manifactured using a Velostat foil. This sensor has responded well to pilot test. Once completed, such device can be used to validate existing numerical models of the knee and of TKA and create new ones, more accurate.It can lead to refinement of surgical techniques, to enhancement of prosthetic designs and, once validated, and if properly modified, it can be used also intraoperatively.

Experimental study on the wave measurements of wave buoys

Wave measurement is of vital importance for assessing the wave power resources and for developing wave energy devices, especially for the wave energy production and the survivability of the wave energy device. Wave buoys are one of the most popular measuring technologies developed and used for long-term wave measurements. In order to figure out whether the wave characteristics can be recorded by using the wave buoys accurately, an experimental study was carried out on the performance of three wave buoy models, viz two WaveScan buoys and one ODAS buoy, in a wave tank using the European FP7 MARINET facilities. This paper presents the test results in both time and frequency domains and the comparison between the wave buoys and wave gauge measurements. The analysis results reveal that for both regular and irregular waves, the WaveScan buoys have better performances than the ODAS buoy in terms of accuracy and the WaveScan buoys measurements have a very good correlation with those from the wave gauges.

Nonlinear soil-structure interaction for buried pressure pipes under differential ground motion

Pipelines extend thousands of kilometers across wide geographic areas as a network to provide essential services for modern life. It is inevitable that pipelines must pass through unfavorable ground conditions, which are susceptible to natural disasters. This thesis investigates the behaviour of buried pressure pipelines experiencing ground distortions induced by normal faulting. A recent large database of physical modelling observations on buried pipes of different stiffness relative to the surrounding soil subjected to normal faults provided a unique opportunity to calibrate numerical tools. Three-dimensional finite element models were developed to enable the complex soil-structure interaction phenomena to be further understood, especially on the subjects of gap formation beneath the pipe and the trench effect associated with the interaction between backfill and native soils. Benchmarked numerical tools were then used to perform parametric analysis regarding project geometry, backfill material, relative pipe-soil stiffness and pipe diameter. Seismic loading produces a soil displacement profile that can be expressed by isoil, the distance between the peak curvature and the point of contraflexure. A simplified design framework based on this length scale (i.e., the Kappa method) was developed, which features estimates of longitudinal bending moments of buried pipes using a characteristic length, ipipe, the distance from peak to zero curvature. Recent studies indicated that empirical soil springs that were calibrated against rigid pipes are not suitable for analyzing flexible pipes, since they lead to excessive conservatism (for design). A large-scale split-box normal fault simulator was therefore assembled to produce experimental data for flexible PVC pipe responses to a normal fault. Digital image correlation (DIC) was employed to analyze the soil displacement field, and both optical fibres and conventional strain gauges were used to measure pipe strains. A refinement to the Kappa method was introduced to enable the calculation of axial strains as a function of pipe elongation induced by flexure and an approximation of the longitudinal ground deformations. A closed-form Winkler solution of flexural response was also derived to account for the distributed normal fault pattern. Finally, these two analytical solutions were evaluated against the pipe responses observed in the large-scale laboratory tests.