Active yaw control of a vehicle using a Fuzzy logic algorithm

Yaw rate of a vehicle is highly influenced by the lateral forces generated at the tire contact patch to attain the desired lateral acceleration, and/or by external disturbances resulting from factors such as crosswinds, flat tire or, split-μ braking. The presence of the latter and the insufficiency of the former may lead to undesired yaw motion of a vehicle. This paper proposes a steer-by-wire system based on fuzzy logic as yaw-stability controller for a four-wheeled road vehicle with active front steering. The dynamics governing the yaw behavior of the vehicle has been modeled in MATLAB/Simulink. The fuzzy controller receives the yaw rate error of the vehicle and the steering signal given by the driver as inputs and generates an additional steering angle as output which provides the corrective yaw moment. The results of simulations with various drive input signals show that the yaw stability controller using fuzzy logic proposed in the current study has a good performance in situations involving unexpected yaw motion. The yaw rate errors of a vehicle having the proposed controller are notably smaller than an uncontrolled vehicle's, and the vehicle having the yaw stability controller recovers lateral distance and desired yaw rate more quickly than the uncontrolled vehicle.

Curvature-constrained trajectory generation for waypoint following for miniature air vehicle

This paper addresses trajectory generation problem of a fixed-wing miniature air vehicle, constrained by bounded turn rate, to follow a given sequence of waypoints. An extremal path, named as g-trajectory, that transitions between two consecutive waypoint segments (obtained by joining two waypoints in sequence) in a time-optimal fashion is obtained. This algorithm is also used to track the maximum portion of waypoint segments with the desired shortest distance between the trajectory and the associated waypoint. Subsequently, the proposed trajectory is compared with the existing transition trajectory in the literature to show better performance in several aspects. Another optimal path, named as loop trajectory, is developed for the purpose of tracking the waypoints as well as the entire waypoint segments. This paper also proposes algorithms to generate trajectories in the presence of steady wind to meet the same objective as that of no-wind case. Due to low computational burden and simplicity in the design procedure, these trajectory generation approaches are implementable in real time for miniature air vehicles.

Using long time series of agricultural-derived nitrates for estimating catchment transit times

The estimation of water and solute transit times in catchments is crucial for predicting the response of hydrosystems to external forcings (climatic or anthropogenic). The hydrogeochemical signatures of tracers (either natural or anthropogenic) in streams have been widely used to estimate transit times in catchments as they integrate the various processes at stake. However, most of these tracers are well suited for catchments with mean transit times lower than about 4-5 years. Since the second half of the 20th century, the intensification of agriculture led to a general increase of the nitrogen load in rivers. As nitrate is mainly transported by groundwater in agricultural catchments, this signal can be used to estimate transit times greater than several years, even if nitrate is not a conservative tracer. Conceptual hydrological models can be used to estimate catchment transit times provided their consistency is demonstrated, based on their ability to simulate the stream chemical signatures at various time scales and catchment internal processes such as N storage in groundwater. The objective of this study was to assess if a conceptual lumped model was able to simulate the observed patterns of nitrogen concentration, at various time scales, from seasonal to pluriannual and thus if it was relevant to estimate the nitrogen transit times in headwater catchments. A conceptual lumped model, representing shallow groundwater flow as two parallel linear stores with double porosity, and riparian processes by a constant nitrogen removal function, was applied on two paired agricultural catchments which belong to the Research Observatory ORE AgrHys. The Global Likelihood Uncertainty Estimation (GLUE) approach was used to estimate parameter values and uncertainties. The model performance was assessed on (i) its ability to simulate the contrasted patterns of stream flow and stream nitrate concentrations at seasonal and inter-annual time scales, (ii) its ability to simulate the patterns observed in groundwater at the same temporal scales, and (iii) the consistency of long-term simulations using the calibrated model and the general pattern of the nitrate concentration increase in the region since the beginning of the intensification of agriculture in the 1960s. The simulated nitrate transit times were found more sensitive to climate variability than to parameter uncertainty, and average values were found to be consistent with results from others studies in the same region involving modeling and groundwater dating. This study shows that a simple model can be used to simulate the main dynamics of nitrogen in an intensively polluted catchment and then be used to estimate the transit times of these pollutants in the system which is crucial to guide mitigation plans design and assessment. (C) 2015 Elsevier B.V. All rights reserved.

Nonlinear control of an air-breathing engine including its validation with vehicle guidance

An implementable nonlinear control design approach is presented for a supersonic air-breathing ramjet engine. The primary objective is to ensure that the thrust generated by the engine tracks the commanded thrust without violating the operational constraints. An important constraint is to manage the shock wave location in the intake so that it neither gets detached nor gets too much inside the intake. Both the objectives are achieved by regulating the fuel flow to the combustion chamber and by varying the throat area of the nozzle simultaneously. The design approach accounts for the nonlinear cross-coupling effects and nullifies those. Also, an extended Kalman filter has been used to filter out the sensor and process noises as well as to make the states available for feedback. Furthermore, independent control design has been carried out for the actuators. To test the performance of the engine for a realistic flight trajectory, a representative trajectory is generated through a trajectory optimization process, which is augmented with a newly-developed finite-time state dependent Riccati equation technique for nullifying the perturbations online. Satisfactory overall performance has been obtained during both climb and cruise phases. (C) 2015 Elsevier Masson SAS. All rights reserved.

Part II: A Fully Integrated RF PA in 28-nm CMOS With Device Design for Optimized Performance and ESD Robustness

In this paper, we report drain-extended MOS device design guidelines for the RF power amplifier (RF PA) applications. A complete RF PA circuit in a 28-nm CMOS technology node with the matching and biasing network is used as a test vehicle to validate the RF performance improvement by a systematic device design. A complete RF PA with 0.16-W/mm power density is reported experimentally. By simultaneous improvement of device-circuit performance, 45% improvement in the circuit RF power gain, 25% improvement in the power-added efficiency at 1-GHz frequency, and 5x improvement in the electrostatic discharge robustness are reported experimentally.

Forebody Compressibility Research of Hypersonic Vehicle

Three kinds of forebody model of hypersonic vehicles were studied with numerical simulation method. It shows that the two- order compressive ramp model is the best selection among the three for its good evaluative parameters value at the cowl of the inlet . This model can provide higher value of flux coefficient and total pressure recovery coefficient and lower average Mach number compared with those of the other two models . Simultaneously different compressive angles may have different effects . The configuration which the firstorder of compressive angle is 4°and the second 5°is the optimum combination. Furthermore factors such as attack angle were concerned. Better result may be obtained with a range of attack angles . Based on the work above the integrated design for forebodyPinlet of a hypersonic vehicle was performed. The numerical result shows that this integrated model provides good flow field quality for inlet and engine work.

High temperature direct double side cooled inverter module for hybrid electric vehicle application

In this paper a novel approach to the design and fabrication of a high temperature inverter module for hybrid electrical vehicles is presented. Firstly, SiC power electronic devices are considered in place of the conventional Si devices. Use of SiC raises the maximum practical operating junction temperature to well over 200°C, giving much greater thermal headroom between the chips and the coolant. In the first fabrication, a SiC Schottky barrier diode (SBD) replaces the Si pin diode and is paired with a Si-IGBT. Secondly, double-sided cooling is employed, in which the semiconductor chips are sandwiched between two substrate tiles. The tiles provide electrical connections to the top and the bottom of the chips, thus replacing the conventional wire bonded interconnect. Each tile assembly supports two IGBTs and two SBDs in a half-bridge configuration. Both sides of the assembly are cooled directly using a high-performance liquid impingement system. Specific features of the design ensure that thermo-mechanical stresses are controlled so as to achieve long thermal cycling life. A prototype 10 kW inverter module is described incorporating three half-bridge sandwich assemblies, gate drives, dc-link capacitance and two heat-exchangers. This achieves a volumetric power density of 30W/cm3.

Thermal fatigue on pistons induced by shaped high power laser. Part II: Design of spatial intensity distribution via numerical simulation

In the laser induced thermal fatigue simulation test on pistons, the high power laser was transformed from the incident Gaussian beam into a concentric multi-circular pattern with specific intensity ratio. The spatial intensity distribution of the shaped beam, which determines the temperature field in the piston, must be designed before a diffractive optical element (DOE) can be manufactured. In this paper, a reverse method based on finite element model (FEM) was proposed to design the intensity distribution in order to simulate the thermal loadings on pistons. Temperature fields were obtained by solving a transient three-dimensional heat conduction equation with convective boundary conditions at the surfaces of the piston workpiece. The numerical model then was validated by approaching the computational results to the experimental data. During the process, some important parameters including laser absorptivity, convective heat transfer coefficient, thermal conductivity and Biot number were also validated. Then, optimization procedure was processed to find favorable spatial intensity distribution for the shaped beam, with the aid of the validated FEM. The analysis shows that the reverse method incorporated with numerical simulation can reduce design cycle and design expense efficiently. This method can serve as a kind of virtual experimental vehicle as well, which makes the thermal fatigue simulation test more controllable and predictable. (C) 2007 Elsevier Ltd. All rights reserved.

Design of an optimised wheel profile for rail vehicles operating on two track gauges

This paper sets out an optimum synthesis methodology for wheel profiles of railway vehicles in order to secure good dynamic behaviour with different track configurations. Specifically, the optimisation process has been applied to the case of rail wheelsets mounted on double gauge bogies, that move over two different gauges, which also have different types of rail: the Iberian gauge (1668 mm) and the UIC gauge (1435 mm). Optimisation is performed using Genetic Algorithms and traditional optimisation methods in a complementary way. The objective function used is based on an ideal equivalent conicity curve which ensures good stability on straight sections and also proper negotiation of curves. To this end the curve is constructed in such a way that it is constant with a low value for small lateral wheelset displacements (with regard to stability), and increases as the displacements increase (to facilitate negotiation of curved sections). Using this kind of ideal conicity curve also enables a wheel profile to be secured where the contact points have a larger distribution over the active contact areas, making wear more homogeneous and reducing stresses. The result is a wheel profile with a conicity that is closer to the target conicity for both gauges studied, producing better curve negotiation while maintaining good stability on straight sections of track. The paper shows the resultant wheel profile, the contact curves it produces, and a number of dynamic analyses demonstrating better dynamic behaviour of the synthesised wheel on curved sections with respect to the original wheel.

Design e desenvolvimento de projeto de sinalização viária urbana

Reclamações contra a sinalização viária existente no Rio de Janeiro são comuns. A cidade ainda é a porta de entrada do Brasil e o destino preferido dos visitantes. Dentro de pouco tempo, o Rio será palco de importantes eventos esportivos internacionais e há preocupação em como poderá a cidade oferecer orientação para os turistas que nela venham a transitar. Este estudo procura saber quais são, de fato, os motivos que justificam as incessantes queixas contra a sinalização instalada e procura extrair daí diretrizes que possam ser aplicadas aos projetos de sistemas de sinalização que efetivamente resolvam os problemas de orientação dos usuários. Para isso, procurou-se primeiro mapear o contexto histórico em que vem evoluindo a sinalização de trânsito; em seguida, examinou-se em que implica o desenvolvimento de projetos de sinalização em geral; para no próximo passo se focar questões da sinalização de trânsito. Foram feitos dois levantamentos: o primeiro, de entrevistas estruturadas individualizadas com taxistas, que são usuários intensos das vias e da sinalização. A amostra escolhida foi de 19 taxistas frequentadores da Praça Santos Dumont, localizada na Zona Sul da cidade, e um importante entroncamento de tráfego. O segundo envolveu cinco profissionais designers com o perfil de experiência prévia no desenvolvimento de projetos de sistemas de sinalização. Com esse grupo, a técnica utilizada foi a de Think Aloud Protocol, através da qual cada um desses indivíduos foi acompanhado e documentado enquanto dirigia e se orientava pela sinalização num trajeto que vai desde a citada Praça Santos Dumont até o Estádio do Maracanã, situado na Zona Norte da cidade, e que costuma ser um destino preferencial em eventos esportivos. Os resultados das duas pesquisas foram analisados e deles extraídas diretrizes que são apresentadas nas Conclusões e que objetivam a eficácia do sistema através de mensagens claras, textos legíveis, posicionamento oportuno e estabilidade formal visando o reconhecimento e o entendimento por parte do usuário.