Formulação de bloco intertravado cerâmico com adição de resíduos urbanos e industriais

The production of waste from urban and industrial activities is one of the factors of environmental contamination and has aroused attention of the scientific community, in the sense of its reuse. On the other hand, the city of Salvador/Ba, with approximately 262 channels, responsible for storm water runoff, produces every year, by the intervention of cleaning and clearing channels, a significant volume of sediments (dredged mud), and thus an appropriate methodology for their final destination. This study aims to assess the influence of incorporation of these tailings in arrays of clay for production of interlocked block ceramic, also known as ceramic paver. All the raw materials from the metropolitan region of Salvador (RMS) were characterized by x-ray fluorescence, x-ray diffraction, thermal analysis (TG and TDA), particle size analysis and dilatometry. With the use of statistical experimental planning technique, ternary diagram was defined in the study region and the analyzed formulations. The specimens were prepared with dimensions of 60x20x5mm³, by uniaxial pressing of 30 MPa and after sintering at temperatures of 900°, 1000º and 1100ºC the technological properties were evaluated: linear shrinkage, water absorption, apparent porosity, apparent specifies mass, flexural rupture and module. For the uniaxial compression strength used cylindrical probe body with Ø 50 mm. The standard mass (MP) was prepared with 90% by weight of clay and 10% by weight of Channel sediment (SCP), not being verified significant variations in the properties of the final product. With the incorporation of 10% by weight of manganese residue (PFM) and 10% by weight of the Ceramic waste (RCB) in the mass default, in addition to adjusting the plasticity due to less waste clay content, provided increased linear firing shrinkage, due the significant concentration of K2O, forming liquid phase at low temperature, contributing to decreased porosity and mechanical resistance, being 92,5 MPa maximum compressive strength verified. After extract test leachate and soluble, the piece containing 10% of the PFM, was classified as non-hazardous and inert material according to NBR10004/04 ABNT. The results showed the feasibility on using waste, SCP, RCB and PFM clay mass, at temperatures above 900ºC, paver ceramic production, according to the specifications of the technical standards, so that to exceed the 10% of the PFM, it becomes imperative to conduct studies of environmental impacts

Estudo da molhabilidade de tecidos 100% poliéster tratados em plasma N2/O2 em função do seu envelhecimento natural

This work reports the influence of the poly (ethylene terephthalate) textile surface modification by plasmas of O2 and mixtures (N2 + O2), on their physical and chemical properties. The treatment was carried out in a vacuum chamber. Some parameters remained constant during all treatment, such as: Voltage 470 V; Pressure 1,250 Mbar; Current: 0, 10 A and gas flow: 10 cm3/min. Other parameters, such as working gas composition and treatment time, were modified as the following: to the O2 plasma modified samples only the treatment time was changed (10, 20, 30, 40, 50 and 60 minutes). To the plasma with O2 and N2 only the chemical concentrations were changed. Through Capillary tests (vertical) an increase in textile wettability was observed as well as its influence on aging time and its consequence on wettability. The surface functional groups created after plasma treatments were investigated using X-ray Photoelectron Spectroscopy (XPS). The surface topography was examined by scanning electron microscope (SEM)

Efeito antibacteriano de tecidos têxteis revestidos por prata através da técnica de deposição por plasma

In this study, it has been investigated the influence of silver film deposition onto 100% polyester woven and non-woven, on the survival of Escherichia coli and Staphylococcus aureus in contact with these surfaces. The treatment was performedin a chamber containing the working gas at low pressure (~ 10-2 mbar). Some process parameters such as as voltage: 470 V; pressure: 10-2 mbar; current : 0.40 A and gas flow: 6 and 10 cm3/min were kept constant. For the treatments with purêargon plasma using a flow of 6 and 10 cm3/min, different treatment times were evaluated, such as, 10 , 20, 30, 40, 50 and 60 minutes. Contact angle (sessile drop), measurements were used to determine the surface tension of the treated fabrics and its influence on the bacteria grow as weel as the possibilities of a biofilm formation. The formation of a silver film, as well as the amount of this element was verified byEDX technique. The topography was observed through scanning electron microscopy (SEM) to determine the size of silver grains formed on the surfaces of the fabric and assess homogeneity of treatment. The X-ray diffraction (XRD) was used to analyze the structure of silver film deposition. The woven fabric treatments enabled the formation of silver particulate films with particle size larger than the non-woven fabrics. With respect to bacterial growth, all fabrics were shown to be bactericidal for Staphylococcus aureus (S. aureus), while for the Escherichia coli (E. coli), the best results were found for the non-woven fabric (TNT) treated with a flow of 10 cm3/min to both bacteria

Caracterização analítica de rochas silicatadas e avaliação de seu potencial agrícola como fonte de potássio.

O presente estudo avaliou a eficiência agronômica da aplicação de pó de rochas silicatadas como fonte de potássio em cultivos consecutivos de milheto e alfafa em casa de vegetação. As rochas Biotita Xisto (BX), Sienito Ceraíma (TA15), Mafurito Acreúna (TA21), Sienito SANW (TA20), Biotita Gnaísse (EL02) e Fonolito Curimbaba (FN) foram aplicadas como fontes de potássio de liberação lenta em três doses de 1,25; 2,50 e 5,0 g de rocha moída por kg de solo. Cloreto de potássio foi utilizado como fertilizante convencional em doses de 0,10; 0,20 e 0,40 g de KCl kg-1 de solo. O solo utilizado nos experimentos foi um latossolo amarelo distrófico de textura média, com teor de potássio de 1,2 mmolc dm-3 solo. A rocha TA21 foi testada sem e com correção da acidez do solo. Com a finalidade de observar a dissolução das rochas em um ambiente com plantas foram realizados cinco cultivos consecutivos: (1) milheto (62 dias de cultivo); (2), (3) e (4) alfafa (80, 115 e 155 dias de cultivo, respectivamente) e (5) milheto, com 80 dias de cultivo. A produção de matéria seca no cultivo da alfafa foi significativamente menor do que o cultivo do milheto. As amostras de forrageira foram digeridas e quantificadas empregando o método de decomposição assistida por radiação micro-ondas com HNO3 + H2O2 para a determinação do teor de potássio extraído pelas plantas. As amostras de rochas foram caracterizadas por fluorescência de raios X, difração de raios X, microscopia eletrônica de varredura e distribuição de tamanho das partículas e submetidas a ensaios com solução extratora Mehlich-1, ácido acético e ácido fumárico 0,05mol L-1, em diferentes tempos de extração. Todos os extratos foram quantificados por espectrometria de emissão óptica com plasma acoplado indutivamente (ICP OES), sendo determinados os teores de Al, Ca, K, Mg, Mn, Na, P e Zn. O método da resina trocadora de íons foi aplicado para todas as amostras de rochas avaliadas, sendo quantificados K, Ca, Mg e P. Potássio solúvel foi determinado por fotometria de chama após extração com água quente, método oficial do Ministério da Agricultura, Pecuária e Abastecimento (MAPA). Para extração drástica foram avaliados dois métodos de decomposição assistida por radiação microondas: com uso de água régia e água régia invertida com adição de H2O2 e 2 etapas de pré-decomposição. Os elementos Al, Ca, K, Mg, Mn, Na e Zn foram quantificados por ICP OES e os resultados obtidos foram comparados por meio do teste t pareado, que indicou não haver diferença significativa entre os métodos de decomposição no intervalo de 95% de confiança. A partir das concentrações obtidas nas extrações e da quantidade de potássio extraída nos cultivos foi realizado o cálculo de correlação entre os extratores e as plantas, considerando a eficiência agronômica. O uso da calagem nos solos que receberam adição da rocha TA21 influenciou significativamente a absorção de potássio, sendo que foi observado efeito relativo à liberação de K apenas quando essa rocha foi adicionada ao solo sem tratamento prévio com a calagem. A ordem decrescente de eficiência de extração de potássio, considerando o total aplicado nos tratamentos e o K extraído pelas plantas foi EL02 > TA21-SC > KCl > FN> BX> TA20 > TA15 > TA21. Os dois métodos de decomposição desenvolvidos apresentaram melhor correlação com o potássio extraído das rochas EL02. O estudo de casa de vegetação corroborou com os ensaios de extração realizados em laboratório, que indicaram que a rocha EL02 é a que possui o maior percentual de liberação de K em relação às demais rochas avaliadas.

Caracterização física e mecânica de argamassas à base de cimento Portland e cinza de casca de arroz residual

Rice husk, employed as an energy source at milling industries in Brazil generates, after burning, a dark ash. This residue is not yet conveniently disposed, being currently dumped on large areas, causing environmental problems. This research intended to evaluate the applications of residual rice husk ashes (RHA) as a partial replacement of cement for mortar production. Rice husk ash was chemically characterized through X-ray fluorescence, determination of carbon content, X-ray diffraction, and laser granulometric analysis. Mortar specimens were submitted to two different exposure conditions: internal and external environments at a maximum period of five months. Physical-mechanical testing were compressive strength and ultrasonic pulse velocity (UPV). Although presenting good mechanical performance, the mortar based on ash (RHA) did not present pozolanicity but it can be employed in cement matrices as inert material (filler).

Are skeletally mature female rats a suitable model to study osteoporosis?

OBJECTIVE: To analyze if female Wistar rats at 56 weeks of age are a suitable model to study osteoporosis. MATERIALS AND METHODS: Female rats with 6 and 36 weeks of age (n = 8 per group) were kept over a 20-week period and fed a diet for mature rodents complete in terms of Ca, phosphorous, and vitamin D. Excised femurs were measured for bone mass using dual-energy x-ray absorptiometry, morphometry, and biomechanical properties. The following serum mar-kers of bone metabolism were analyzed: parathyroid hormone (PTH), osteocalcin (OC), osteoprotegerin (OPG), receptor activator of nuclear factor Κappa B ligand (RANKL), C-terminal peptides of type I collagen (CTX-I), total calcium, and alkaline phosphatase (ALP) activity. RESULTS: Rats at 56 weeks of age showed important bone metabolism differences when compared with the younger group, such as, highest diaphysis energy to failure, lowest levels of OC, CTX-I, and ALP, and elevated PTH, even with adequate dietary Ca. CONCLUSION: Rats at 26-week-old rats may be too young to study age-related bone loss, whereas the 56-week-old rats may be good models to represent the early stages of age-related changes in bone metabolism.

Mineralogical characterization of a highly-weathered soil by the Rietveld Method

The mineralogical characterization through mineral quantification of Brazilian soils by X-ray diffraction data using the Rietveld Method is not common. A mineralogical quantification of an Acric Ferralsol from the Ponta Grossa region, state of Paraná, Brazil, was carried out using this Method with X-Ray Diffraction data to verify if this method was suitable for mineral quantification of a highly-weathered soil. The A, AB and B3 horizons were fractioned to separate the different particle sizes: clay, silt, fine sand (by Stokes Law) and coarse sand fractions (by sieving), with the procedure free of chemical treatments. X-ray Fluorescence, Inductively Coupled Plasma Atomic Emission Spectrometry, Infrared Spectroscopy and Mössbauer Spectroscopy were used in order to assist the mineral identification and quantification. The Rietveld Method enabled the quantification of the present minerals. In a general way, the quantitative mineralogical characterization by the Rietveld Method revealed that quartz, gibbsite, rutile, hematite, goethite, kaolinite and halloysite were present in the clay and silt fractions of all horizons. The silt fractions of the deeper horizons were different from the more superficial ones due to the presence of large amounts of quartz. The fine and the coarse sand fractions are constituted mainly by quartz. Therefore, a mineralogical quantification of the finer fraction (clay and silt) by the Rietveld Method was successful.

Mineralogia de um latossolo vermelho distrófico submetido a diferentes manejos por 24 anos

Atualmente, procuram-se sistemas de manejo que preservem ou melhorem as qualidades do solo, tanto mineralógicas como orgânicas, priorizando maior produtividade. Este trabalho teve como objetivo verificar qualitativamente, por meio das técnicas de fluorescência de raios X, difração de raios X e infravermelho com transformada de Fourier, os efeitos provocados pela utilização dos manejos: plantio convencional, preparo mínimo e plantio direto, por 24 anos, na mineralogia de um Latossolo Vermelho distrófico de Ponta Grossa, PR. Não foram observadas mudanças significativas na mineralogia do Latossolo estudado, por meio das técnicas utilizadas, quanto aos diferentes manejos durante os anos de sua aplicação. Pôde-se verificar, qualitativamente, a presença dos minerais gibbsita, caulinita, haloisita, montmorilonita, hematita, rutilo, anatásio, goethita e quartzo.

A medição da grandeza practical peak voltage na prática radiológica

OBJETIVO: O objetivo deste trabalho foi estudar a grandeza practical peak voltage (PPV), determinada a partir da forma de onda de tensão aplicada a tubos radiológicos, e compará-la com algumas definições de kVp para diferentes tipos de geradores: monofásico (onda completa, clínico), trifásico (seis pulsos, clínico) e potencial constante (industrial). MATERIAIS E MÉTODOS: O trabalho envolveu a comparação do PPV medido invasivamente (utilizando um divisor de tensão) com a resposta de dois medidores comerciais não invasivos, além dos valores de outras grandezas usadas para medição da tensão de pico aplicada ao tubo de raios X, e a análise da variação do PPV com a ondulação percentual da tensão (ripple). RESULTADOS: Verificou-se que a diferença entre o PPV e as definições mais comuns de tensão de pico aumenta com o ripple. Os valores de PPV variaram em até 3% e 5%, respectivamente, na comparação entre medições invasivas e não invasivas feitas com os equipamentos trifásico e monofásico. CONCLUSÃO: Os resultados demonstraram que a principal grandeza de influência que afeta o PPV é o ripple da tensão. Adicionalmente, valores de PPV obtidos com medidores não invasivos devem ser avaliados considerando que eles dependem da taxa de aquisição e da forma de onda adquirida pelo instrumento.

Study of mural paintings by Fulvio Pennacchi in São Paulo City by mineralogical techniques

The present research deals with two mural paintings made in 1947 with the fresco technique by Fulvio Pennacchi in the Catholic Chapel of the Hospital das Clínicas (São Paulo City, Brazil), namely the Virgin Annunciation and the Supper at Emmaus. This study regards the materials and painting techniques used by the artist, based on historical research,on in situ observations and laboratory analytical techniques (stereomicroscopy,scanning electron microscopy with an energy dispersive spectrometer, X-ray diffractometry, electron microprobe, images obtained with UV-light), aiming to improve the methods of characterization of objects of our cultural heritage, and to enhance its preservation accordingly. The results lead to the identification of the plaster components and of distinct layers in the frescoes, besides further information on grain size, impurities and textures, composition of pigments, and features of deterioration, such as efflorescences. The degree of degradation of the murals painting was assessed by this way. Our data suggest that a single layer of plaster was used by Pennacchi, as a common mortar with fine- and medium-grained aggregates. Differences in texture were obtained by adding gypsum to the plaster.

Synthesis of Fe/Ti oxides from a single source alkoxide precursor under inert atmosphere

The heterometal alkoxide [FeCl{Ti2(OPr i)9}] (1) was employed as a single source precursor for the preparation of Fe/Ti oxides under inert atmosphere. Three different synthetic procedures were adopted in the processing of 1, either employing aqueous HNO3 or HCl solutions, or in the absence of mineral acids. Products were characterised by powder X-ray diffractometry, scanning electron microscopy combined with energy dispersive X-ray spectroscopy (SEM/EDS) and Raman, electron paramagnetic resonance (EPR) and Mössbauer spectroscopies. Oxide products contained titanium(IV) and either iron(III) or iron(II), depending on reaction conditions and thermal treatment temperatures. An interesting iron(III)→iron(II) reduction was observed at 1000 ºC in the HNO3-containing system, leading to the detection of ilmenite (FeTiO3). SEM/EDS studies revealed a highly heterogeneous metal distribution in all products, possibly related to the presence of a significant content of carbon and of structural defects (oxygen vacancies) in the solids.

Low temperature synthesis of CdSiO3 nanostructures

We report the synthesis of single-phase, crystalline CdSiO3 nanostructures at 580ºC; to the best of our knowledge, this is the lowest temperature at which this material is reported to form. The desired phase does not form below 580ºC, since the diffraction peaks are shifted to lower angles in the material treated at 570ºC when compared to JDPDS Card No. 85-0310. The source of silicon has strong influence on the product morphology: Na2SiO3 yields single-phase CdSiO3 in needle-shaped nanostructures, while high surface area mesostructured SiO2 yields coralloid-shaped particles. Low angle X-ray diffractometry reveals that the mesostructured nature of the silica precursor is not maintained in the resulting CdSiO3. Scanning electron microscopy suggests that in this case a transition occurs between the spherical morphology of the precursor and the needle-shape morphology of the material prepared from Na2SiO3. The surface area of the silica precursor has a strong influence in the reaction, since the use of commercial silica with a lower surface area does not yield the desired product.

Caracterização de cálculos renais por análise térmica

Dez amostras de cálculos renais foram estudadas por Análise Elementar de CHN (EA), Espectroscopia de Absorção no Infravermelho (IV) e Difração de raios X pelo método de Pó (XRD). O comportamento térmico das amostras foi estudado por Termogravimetria/Termogravimetria Derivada (TG/DTG) e por Calorimetria Exploratória Diferencial (DSC). Os resultados de EA, Espectroscopia de Absorção IV e XRD mostraram a presença de estruvita [NH4Mg(PO4).6H2O], apatita, oxalato de cálcio monohidratado e oxalato de cálcio dihidratado. As curvas TG e DSC permitiram classificar as amostras em dois grupos diferentes: Grupo I mostrando comportamento térmico típico de estruvita e Grupo II apresentando um perfil termoanalítico característico de mistura de oxalatos.

Association between osteoporosis and rheumatoid arthritis in women: a cross-sectional study

CONTEXT AND OBJECTIVES: Osteoporosis has frequently been observed in patients with rheumatoid arthritis. The present study was undertaken in order to evaluate factors associated with osteoporosis among women with rheumatoid arthritis. DESIGN AND SETTING: Cross-sectional study, carried out in a public hospital in São Paulo. METHODS: The participants were 83 women with rheumatoid arthritis (53.7 ± 10.0 years old). Bone mineral density (BMD) and body composition were measured by dual energy X-ray absorptiometry. The patients were divided into three groups according to BMD: group 1, normal BMD (n = 24); group 2, osteopenia (n = 38); and group 3, osteoporosis (n = 21). Tests were performed to compare differences in means and correlations, with adjustments for age, duration of disease and cumulative corticosteroid. The relationships between clinical factors, physical activity score, dietary intake, body composition and biochemical parameters were analyzed using linear regression models. RESULTS: Mean calcium, vitamin D and omega-6 intakes were lower than the recommendations. Associations were found between BMD and age, disease duration, parathyroid hormone concentration and fat intake. The linear regression model showed that being older, with more years of disease and lower weight were negatively correlated with BMD [Total femur = 0.552 + 0.06 (weight) + 0.019 (total physical activity) - 0.05 (age) - 0.003 (disease duration); R² = 48.1; P < 0.001]. CONCLUSION: The present study indicates that nutritional factors and body composition are associated with bone mass in women with rheumatoid arthritis.

Notificação imprecisa da ingestão energética na dieta de adolescentes

Objetivos: Examinar a prevalência da sub e supernotificação da ingestão energética em adolescentes e seus fatores associados. Métodos: Estudo transversal com 96 adolescentes na pós-puberdade (47 com peso normal e 49 obesos), com idade média de 16,6±1,3 anos. Peso e altura foram medidos e o índice de massa corporal foi calculado. A composição corporal foi avaliada através de absorciometria por raios X de dupla energia. A ingestão de alimentos foi avaliada por meio de um registro alimentar de 3 dias. Realizou-se uma avaliação bioquímica (níveis séricos de colesterol total, LDL, HDL, glicose plasmática e insulina). Os subnotificadores relataram uma ingestão energética < 1,35 x taxa metabólica basal (TMB), enquanto os supernotificadores relataram uma ingestão energética > 2,4 x TMB. Resultados: Notificação imprecisa (sub ou supernotificação) da ingestão energética foi identificada em 65,6 por cento dos adolescentes (64,6 e 1 por cento de sub e supernotificação, respectivamente). Os adolescentes obesos apresentaram 5.0 vezes mais chances de subnotificar a ingestão energética (IC95 por cento 2,0-12,7) do que os participantes com peso normal. Os subnotificadores apresentaram taxas mais altas de ingestão insuficiente de carboidratos (19,3 versus 12,1 por cento, p = 0,046) e de lipídios (11,3 versus 0 por cento, p < 0,001) do que os notificadores plausíveis. A ingestão de colesterol também foi mais baixa entre os subnotificadores (p = 0,017). Não houve diferenças significativas na composição corporal e nos parâmetros bioquímicos em relação à notificação imprecisa. Conclusões: Os resultados obtidos demonstraram alta porcentagem de notificação imprecisa da ingestão energética entre adolescentes, principalmente entre os obesos, o que sugere que os valores de consumo de nutrientes ajustado para o consumo de energia deveriam ser empregados na análise de risco da relação dieta-doença a fim de contribuir para a redução de erros associados à notificação imprecisa