Sistema integrado de localização de contentores de correio

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Informática e de Computadores

Time-Reversal Massive Multipath Effect and Bandwidth Heterogeneity

The proliferation of new mobile communication devices, such as smartphones and tablets, has led to an exponential growth in network traffic. The demand for supporting the fast-growing consumer data rates urges the wireless service providers and researchers to seek a new efficient radio access technology, which is the so-called 5G technology, beyond what current 4G LTE can provide. On the other hand, ubiquitous RFID tags, sensors, actuators, mobile phones and etc. cut across many areas of modern-day living, which offers the ability to measure, infer and understand the environmental indicators. The proliferation of these devices creates the term of the Internet of Things (IoT). For the researchers and engineers in the field of wireless communication, the exploration of new effective techniques to support 5G communication and the IoT becomes an urgent task, which not only leads to fruitful research but also enhance the quality of our everyday life. Massive MIMO, which has shown the great potential in improving the achievable rate with a very large number of antennas, has become a popular candidate. However, the requirement of deploying a large number of antennas at the base station may not be feasible in indoor scenarios. Does there exist a good alternative that can achieve similar system performance to massive MIMO for indoor environment? In this dissertation, we address this question by proposing the time-reversal technique as a counterpart of massive MIMO in indoor scenario with the massive multipath effect. It is well known that radio signals will experience many multipaths due to the reflection from various scatters, especially in indoor environments. The traditional TR waveform is able to create a focusing effect at the intended receiver with very low transmitter complexity in a severe multipath channel. TR's focusing effect is in essence a spatial-temporal resonance effect that brings all the multipaths to arrive at a particular location at a specific moment. We show that by using time-reversal signal processing, with a sufficiently large bandwidth, one can harvest the massive multipaths naturally existing in a rich-scattering environment to form a large number of virtual antennas and achieve the desired massive multipath effect with a single antenna. Further, we explore the optimal bandwidth for TR system to achieve maximal spectral efficiency. Through evaluating the spectral efficiency, the optimal bandwidth for TR system is found determined by the system parameters, e.g., the number of users and backoff factor, instead of the waveform types. Moreover, we investigate the tradeoff between complexity and performance through establishing a generalized relationship between the system performance and waveform quantization in a practical communication system. It is shown that a 4-bit quantized waveforms can be used to achieve the similar bit-error-rate compared to the TR system with perfect precision waveforms. Besides 5G technology, Internet of Things (IoT) is another terminology that recently attracts more and more attention from both academia and industry. In the second part of this dissertation, the heterogeneity issue within the IoT is explored. One of the significant heterogeneity considering the massive amount of devices in the IoT is the device heterogeneity, i.e., the heterogeneous bandwidths and associated radio-frequency (RF) components. The traditional middleware techniques result in the fragmentation of the whole network, hampering the objects interoperability and slowing down the development of a unified reference model for the IoT. We propose a novel TR-based heterogeneous system, which can address the bandwidth heterogeneity and maintain the benefit of TR at the same time. The increase of complexity in the proposed system lies in the digital processing at the access point (AP), instead of at the devices' ends, which can be easily handled with more powerful digital signal processor (DSP). Meanwhile, the complexity of the terminal devices stays low and therefore satisfies the low-complexity and scalability requirement of the IoT. Since there is no middleware in the proposed scheme and the additional physical layer complexity concentrates on the AP side, the proposed heterogeneous TR system better satisfies the low-complexity and energy-efficiency requirement for the terminal devices (TDs) compared with the middleware approach.

Electrical characterization of electronic circuits produced by inkjet printing

Dissertação de Mestrado, Engenharia Electrónica e Telecomunicações, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2014

Colaboración fabricante-distribuidor en la cadena de suministro para la tecnología aplicada al punto de venta y la mejora de la experiencia de compra

A lo largo de este trabajo se lleva a cabo una investigación sobre la evolución de las relaciones comerciales entre fabricantes y distribuidores, con especial atención en la colaboración conjunta a la hora de comercializar los productos en el punto de venta. El empleo de nuevas herramientas tecnológicas en el establecimiento facilita el merchandising de presentación, ofreciendo ventajas competitivas para los agentes de la cadena de suministros y nuevas experiencias de compra para los consumidores. Una vez analizada la parte teórico-conceptual del trabajo se lleva a cabo el análisis de un caso práctico sobre los beneficios de la tecnología Radio Frequency Identification (RFID) implantada en la empresa Decathlon. Estos sistemas se han convertido en un aliado clave para la mejora de los procesos de negocio, mejorando la gestión de la compañía y la fidelización de los clientes.

Structural Health Monitoring Inside Concrete and Grout Using the Wireless Identification and Sensing Platform (WISP)

This research investigates the implementation of battery-less RFID sensing platforms inside lossy media, such as, concrete and grout. Both concrete and novel grouts can be used for nuclear plant decommissioning as part of the U.S. Department of Energy’s (DOE’s) cleanup projects. Our research examines the following: (1) material characterization, (2) analytical modeling of transmission and propagation losses inside lossy media, (3) maximum operational range of RFID wireless sensors embedded inside concrete and grout, and (4) best positioning of antennas for achieving longer communication range between RFID antennas and wireless sensors. Our research uses the battery-less Wireless Identification and Sensing Platform (WISP) which can be used to monitor temperature, and humidity inside complex materials. By using a commercial Agilent open-ended coaxial probe (HP8570B), the measurements of the dielectric permittivity of concrete and grout are performed. Subsequently, the measured complex permittivity is used to formulate analytical Debye models. Also, the transmission and propagation losses of a uniform plane wave inside grout are calculated. Our results show that wireless sensors will perform better in concrete than grout. In addition, the maximum axial and radial ranges for WISP are experimentally determined. Our work illustrates the feasibility of battery-less wireless sensors that are embedded inside concrete and grout. Also, our work provides information that can be used to optimize the power management, sampling rate, and antenna design of such sensors.

Identification technologies to support Alzheimer contexts

Alzheimer's disease makes great demands on care by assistants, due to the fact that they cannot distract their attention from patients while they are at the same time managing records. For that reason, technologies to complement this process need to be adapted. In this work we present a proposal to adapt identification technologies: Radiofrequency Identification (RFID) and Near Field Communications (NFC), focusing especially on the last one. We fuse both technologies and apply them to an Alzheimer's day center. Patients are tagged with two kinds of labels: 13.56Mhz.Mifare for NFC and UHF for RFID. With the first one we tag the context, which means patients, devices (displays, exercise books, etc) and places. With a simple interaction, which involves touching tags with mobile phones, it is possible to manage the information easily. Moreover, with RFID, we localize each patient by the simple act of their passing by an antenna placed in the doors.

Un approccio multiscala alle dinamiche fluviali di alvei montani

Questo lavoro di tesi è finalizzato allo studio delle morfodinamiche fluviali in ambiente montano, in risposta a forzanti antropiche e naturali. In particolare, si prendono in considerazione sistemi Appenninici (i.e., Fiume Santerno) e Alpini (i.e., Rii Grigno, Tolvà e Ussaia), integrando due approcci che si sviluppano su scale spazio-temporali differenti. Nel caso Appenninico vengono esaminati i cambiamenti planimetrici dell’alveo attivo del Fiume Santerno in risposta ad impatti antropici, quali l’estrazione di inerti in alveo, la costruzione di opere idrauliche e l’alterazione di uso del suolo a scala di bacino. Nei tre casi Alpini, che si differenziano in termini di forzante idro-meteorologica ed apporto di sedimento da monte, si è valutato il trasporto solido di fondo (bedload transport) mediante tecnologia RFID.

Smart tracking of composite parts: feasibility study and effect on mechanical behaviour

This research proposes a solution for integrating RFID - Radio Frequency Identification technology within a structure based on CFRPs - Carbon Fiber Reinforced Polymers. Therefore, the main objective is to use technology to monitor and track composite components during manufacturing and service life. The study can be divided into two macro-areas. The first portion of the research evaluates the impact of the composite materials used on transmitting the electromagnetic signal to and from the tag. RFID technology communicates through radio frequencies to to track and trace items associated with the tags. In the first instance, a feasibility study was carried out to assess using commercially available tags. Then, after evaluating different solutions, it was decided to incorporate the tags into coupons during production. The second portion of the research is focused on evaluating the impact on the composite material's resistance to tag embedding. It starts with designing tensile test specimens through the FEM model with different housing configurations. Subsequently, the best configuration was tested in the facilities of the In the Faculty of Aerospace Engineering at TU Delft, particularly in the Structure & Materials Laboratory, two tests were conducted: the first one based on ASTM D3039/D3039 - 14 - Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, the second one dividing the path to failure into failure intervals in a load-unload-reload. Both tests were accompanied by instruments such as DIC, AE, C-Scan and Optical Microscopes. The expected result of the inclusion of RFID tags in composite components is that it brings added value to the parts with which it is associated without affecting too much its mechanical properties. This comes first from the automatic identification of RFID during the production cycle and its useful life. As a result, improvements were made in the design of production facilities.

Applicazione degli strumenti di lean production alla logistica di magazzino: il caso Ima Tea&Herbs

L'elaborato valuta i benefici per un'azienda derivanti dall'introduzione di una flotta di AMR, di tray di movimentazione e di un sistema di tracciamento degli utensili tramite RFID

Digitalizzazione nelle aziende multiservizi

Al giorno d'oggi le aziende multiservizi non sono aggiornate per quanto riguarda la transizione digitale. Questo determina un aumento dei costi per l'azienda e un peggioramento del servizio offerto al cliente. Tale situazione, però, è destinata a cambiare. Infatti, sono state introdotte diverse forme di finanziamento per aiutare le aziende a compiere la transizione necessaria con specifici interventi finanziari che hanno lo scopo di sostenere gli innumerevoli progetti di digitalizzazione lanciati dalle aziende stesse. In futuro anche le aziende multiservizi saranno ottimamente digitalizzate, competitive ed efficienti.