Appropriateness of reporting statistical results in orthodontics: the dominance of P values over confidence intervals

The purpose of this study was to search the orthodontic literature and determine the frequency of reporting of confidence intervals (CIs) in orthodontic journals with an impact factor. The six latest issues of the American Journal of Orthodontics and Dentofacial Orthopedics, the European Journal of Orthodontics, and the Angle Orthodontist were hand searched and the reporting of CIs, P values, and implementation of univariate or multivariate statistical analyses were recorded. Additionally, studies were classified according to the type/design as cross-sectional, case-control, cohort, and clinical trials, and according to the subject of the study as growth/genetics, behaviour/psychology, diagnosis/treatment, and biomaterials/biomechanics. The data were analyzed using descriptive statistics followed by univariate examination of statistical associations, logistic regression, and multivariate modelling. CI reporting was very limited and was recorded in only 6 per cent of the included published studies. CI reporting was independent of journal, study area, and design. Studies that used multivariate statistical analyses had a higher probability of reporting CIs compared with those using univariate statistical analyses. Misunderstanding of the use of P values and CIs may have important implications in implementation of research findings in clinical practice.

Microwave-assisted wet chemical (MAWC) synthesis of lithium iron phosphate

LiFePO4 is a Co-free battery material. Its advantages of low cost, non-toxic and flat discharge plateau show promising for vehicle propulsion applications. A major problem associated with this material is its low electrical conductivity. Use of nanosized LiFePO4 coated with carbon is considered a solution because the nanosized particles have much shorter path for L+ ions to travel from the LiFePO4 crystal lattice to electrolytes. As other nano material powders, however, nano LiFePO4 could have processing and health issues. In order to achieve high electrical conductivity while maintaining a satisfactory manufacturability, the particles should possess both of the nano- and the microcharacteristics correspondingly. These two contradictory requirements could only be fulfilled if the LiFePO4 powders have a hierarchical structure: micron-sized parent particles assembled by nanosized crystallites with appropriate electrolyte communication channels. This study addressed the issue by study of the formation and development mechanisms of the LiFePO4 crystallites and their microstructures. Microwaveassisted wet chemical (MAWC) synthesis approach was employed in order to facilitate the evolvement of the nanostructures. The results reveal that the LiFePO4 crystallites were directly nucleated from amorphous precursors by competition against other low temperature phases, Li3PO4 and Fe3(PO4)2•8H2O. Growth of the crystalline LiFePO4 particles went through oriented attachment first, followed by revised Ostwald ripening and then recrystallization. While recrystallization played the role in growth of well crystallized particles, oriented attachment and revised Ostwald ripening were responsible for formation of the straight edge and plate-like shaped LiFePO4 particles comprised of nanoscale substructure. Oriented attachment and revised Ostwald ripening seemed to be also responsible for clustering the plate-like LiFePO4 particles into a high-level aggregated structure. The finding from this study indicates a hope for obtaining the hierarchical structure of LiFePO4 particles that could exhibit the both micro- and nano- scale characteristics. Future study is proposed to further advance the understanding of the structural development mechanisms, so that they can be manipulated for new LiFePO4 structures ideal for battery application.

Lograr estética y función en el sector posterior con resinas compuestas

La operatoria dental actual cuenta con un conocimiento más profundo de las diferentes estructuras dentarias que sumado al gran adelanto tecnológico y científico en la ciencia de los biomateriales; fruto de innumerables investigaciones, nos permiten contar hoy, con una nueva generación de materiales restauradores, lo que hace más crítico y exigente el conocimiento y análisis por parte del profesional, de las técnicas a efectuar, la realización depurada de procedimientos y los biomateriales a utilizar, con el fin de realizar tratamientos que sean biocompatibles, eficientes y de importante longevidad.

Halocarbons in surface water from SWEDARP97/98

A number of parameters of biogeochemical interest were monitored along a north-southerly transect (S 43-S 63°) in the Atlantic Sector of the Southern Ocean from the 8th to the 20th of December 1997. Changes in total dissolved inorganic carbon (CT) and total alkalinity (AT) were mostly dependent on temperature and salinity until the ice edge was reached. After this point only a weak correlation was seen between these. Highest mean values of CT and AT were observed in the Winter Ice Edge (WIE) (2195 and 2319 µmol/kg, respectively). Lowest mean AT (2277 µmol/kg) was observed in the Sub-Antarctic Front (SAF), whereas lowest mean CT concentration (2068 µmol/kg) was associated with the Sub-Tropical Front (STF). The pH in situ varied between 8.060 and 8.156 where the highest values were observed in the southern part of the Antarctic Polar Front (APF) and in the Summer Ice Edge (SIE) Region . These peaks were associated with areas of high chlorophyll a (chl a) and tribromomethane values. In the other areas the pH in situ was mainly dependent on hydrography. Bacterial abundance decreased more than one order of magnitude when going from north to south. The decrease appeared to be strongly related to water temperature and there were no elevated abundances at frontal zones. Microphytoplankton dominated in the SAF and APF, whereas the nano- and picoplankton dominated outside these regions. Volatile halogenated compounds were found to vary both with regions, and with daylight. For the iodinated compounds, the highest concentrations were found north of the STF. Brominated hydrocarbons had high concentrations in the STF, but elevated concentrations were also found in the APF and SIE regions. No obvious correlation could be found between the occurrence of individual halocarbons and chl a. On some occasions trichloroethene and tribromomethane related to the presence of nano- and microplankton, respectively.

Biogeochemical measurements at the Antarctic Peninsula

Size-fractionated chlorophyll a and photosynthetic carbon incorporation, microbial oxygen production and respiration and particulate vertical flux were measured in January 1996 at three regions, characterized by distinct hydrographic fields and planktonic communities, of the Antarctic Peninsula: (1) a diatom-Phaeocystis sp., dominated community associated with the relatively stratified waters of the Gerlache Strait, (2) a nanoplankton-Cryptomonas sp. dominated assemblage at the Gerlache-Bransfield confluence; and (3) a nano- and picoplankton community in mixed waters of the Bransfield Strait. Despite the marked differences in both community structure and total phytoplankton biomass and primary production, and against predictions from models about trophic control of C export, the lowest respiration rates were measured at Bransfield (pico- and nanoplankton), and no difference was observed between the Gerlache (large diatoms) and Bransfield stations in relative vertical particle flux (6.4 vs. 5.1 % of suspended C; 14.9 vs. 10.4 % of net community production, respectively). Growth and loss rates of the phytoplankton population studied for each community indicate that microbial populations can be explained by in situ growth, but spatial (diatom-Phaeocystis sp., bloom) and temporal (diatom-Phaeocystis sp. bloom and nanoplankton communities) scales of study were shown to be insufficient for addressing the coupling between primary production and biogenic carbon export, especially after the appreciation of the accumulation of dissolved organic carbon in the water column. This would explain the unexpected results and highlights the necessity of including the mechanisms controlling accumulation and consumption of dissolved organic matter into conceptual models about the trophic control of C export.

Carbon cycling in the northern Humboldt Current off Chile

The structure of the zooplankton foodweb and their dominant carbon fluxes were studied in the upwelling system off northern Chile (Mejillones Bay; 23°S) between October 2000 and December 2002. High primary production (PP) rates (18 gC/m**2 d) were mostly due to the net-phytoplankton size fraction (>23 µm). High PP has been traditionally associated with the wind-driven upwelling fertilizing effect of equatorial subsurface waters, which favour development of a short food chain dominated by a few small clupeiform fish species. The objective of the present work was to study the trophic carbon flow through the first step of this 'classical chain' (from phytoplankton to primary consumers such as copepods and euphausiids) and the carbon flow towards the gelatinous web composed of both filter-feeding and carnivorous zooplankton. To accomplish this objective, feeding experiments with copepods, appendicularians, ctenophores, and chaetognaths were conducted using naturally occurring plankton prey assemblages. Throughout the study, the total carbon ingestion rates showed that the dominant appendicularian species and small copepods consumed an average of 7 and 5 µgC/ind d, respectively. In addition, copepods ingested particles mainly in the size range of nano- and microplankton, whereas appendicularians ingested in the range of pico- and nanoplankton. Small copepods and appendicularians removed a small fraction of total daily PP (range 6-11%). However, when the pico- + nanoplankton fractions were the major contributors to total PP (oligotrophic conditions), grazing by small copepods increased markedly to 86% of total PP. Under these more oligotrophic conditions, the euphausiids grazing increased as well, but only reached values lower than 5% of total PP. During this study, chaetognaths and ctenophores ingested an average of 1 and 14 copepods/ind d, respectively. In terms of biomass consumed, the potential impact of carnivorous gelatinous zooplankton on the small-size copepod community (preferred prey) was important (2-12% of biomass removed daily). However, their impact produced more significant results on copepod abundance (up to 33%), which suggests that carnivorous gelatinous zooplankton may even modulate (control) the abundance of some species as well as the size structure of the copepod community.

Integrated luminescent chemical microsensors based on GaN LEDs for security applications using smartphones

Development of PCB-integrateable microsensors for monitoring chemical species is a goal in areas such as lab-on-a-chip analytical devices, diagnostics medicine and electronics for hand-held instruments where the device size is a major issue. Cellular phones have pervaded the world inhabitants and their usefulness has dramatically increased with the introduction of smartphones due to a combination of amazing processing power in a confined space, geolocalization and manifold telecommunication features. Therefore, a number of physical and chemical sensors that add value to the terminal for health monitoring, personal safety (at home, at work) and, eventually, national security have started to be developed, capitalizing also on the huge number of circulating cell phones. The chemical sensor-enabled “super” smartphone provides a unique (bio)sensing platform for monitoring airborne or waterborne hazardous chemicals or microorganisms for both single user and crowdsourcing security applications. Some of the latest ones are illustrated by a few examples. Moreover, we have recently achieved for the first time (covalent) functionalization of p- and n-GaN semiconductor surfaces with tuneable luminescent indicator dyes of the Ru-polypyridyl family, as a key step in the development of innovative microsensors for smartphone applications. Chemical “sensoring” of GaN-based blue LED chips with those indicators has also been achieved by plasma treatment of their surface, and the micrometer-sized devices have been tested to monitor O2 in the gas phase to show their full functionality. Novel strategies to enhance the sensor sensitivity such as changing the length and nature of the siloxane buffer layer are discussed in this paper.

Calculation of the spatial distribution of photovoltaic field by arbitrary 2D ilumination patterns en LiNbO3; application to photovoltaic particle trapping.

Patterns of evanescent photovoltaic field induced by illumination on a surface of lithium niobate (LN) have been calculated and compared with the experimental patterns of nano- and microparticles trapped by dielectrophoretic forces. A tool for this calculation has been developed. Calculo de distribución espacial de campo por efecto fotovoltaico con patrones arbitrarios de iluminación, en LiNbO3

The role of the secondary cell wall in plant resistance to pathogens

Plant resistance to pathogens relies on a complex network of constitutive and inducible defensive barriers. The plant cell wall is one of the barriers that pathogens need to overcome to successfully colonize plant tissues. The traditional view of the plant cell wall as a passive barrier has evolved to a concept that considers the wall as a dynamic structure that regulates both constitutive and inducible defense mechanisms, and as a source of signaling molecules that trigger immune responses. The secondary cell walls of plants also represent a carbon-neutral feedstock (lignocellulosic biomass) for the production of biofuels and biomaterials. Therefore, engineering plants with improved secondary cell wall characteristics is an interesting strategy to ease the processing of lignocellulosic biomass in the biorefinery. However, modification of the integrity of the cell wall by impairment of proteins required for its biosynthesis or remodeling may impact the plants resistance to pathogens. This review summarizes our understanding of the role of the plant cell wall in pathogen resistance with a focus on the contribution of lignin to this biological process.

Influencia de la adición de nanosílice y microsílice en el comportamiento mecánico, microestructural y durable de un hormigón autocompactante

Desde mediados de la década de los 80 se está investigando sobre el hormigón autocompactante. Cada día, su uso en el mundo de la construcción es más común debido a sus numerosas ventajas como su excelente fluidez ya que puede fluir bajo su propio peso y llenar encofrados con formas complicadas y muy armados sin necesidad de compactaciones internas o externas. Por otra parte, la búsqueda de materiales más resistentes y duraderos, ha dado lugar a la incorporación de adiciones en materiales a base de cemento. En las últimas dos décadas, los ensayos con los nanomateriales, ha experimentado un gran aumento. Los resultados hasta ahora obtenidos pueden asumir no sólo un aumento en la resistencia de estos materiales, pero un cambio es su funcionalidad. Estas nanopartículas, concretamente la nanosílice, no sólo mejoran sus propiedades mecánicas y especialmente sus propiedades durables, sino que pueden implicar un cambio sustancial en las condiciones de uso y en su ciclo de vida. Este trabajo tiene como principal objetivo el estudio de las propiedades mecánicas, características microestructurales y durables de un hormigón autocompactante cuando se le agrega como adición nanosílice, microsílice y mezcla binarias de ambas, como adición al cemento. Para ello se han realizado 10 mezclas de hormigón. Se utilizó como referencia un hormigón autocompactante obtenido con cemento, caliza, árido, aditivo modificador de viscosidad Se han fabricado tres hormigones con la misma dosificación pero con diferentes contenidos de nanosílice. 2,5%, 5% y 7,5% Tres dosificaciones con adición de microsílice 2,5%, 5% y 7,5% y las tres restantes con mezclas binarias de nanosílice y microsílice con respectivamente2,5%-2,5%, 5%-2,5% y 2,5%-5%, sobre el peso del cemento. El contenido de superplastificante se modificó para conseguir las características de autocompactabilidad. Para observar los efectos de las adiciones añadidas al hormigón, se realiza una extensa campaña experimental. En ella se evaluaron en primer lugar, las características de autocompactabilidad del material en estado fresco, mediante los ensayos prescritos en la Instrucción Española del hormigón estructural EHE 08. Las propiedades mecánicas fueron evaluadas con ensayos de resistencia a compresión, resistencia a tracción indirecta y módulo de elasticidad. Las características microestructurales fueron analizadas mediante porosimetría por intrusión de mercurio, el análisis termogravimétrico y la microscopía electrónica de barrido. Para el estudio de la capacidad durable de las mezclas se realizaron ensayos de resistividad eléctrica, migración de cloruros, difusión de cloruros, carbonatación acelerada, absorción capilar y resistencia al hielo-deshielo. Los resultados ponen de manifiesto que la acción de las adiciones genera mejoras en las propiedades resistentes del material. Así, la adición de nanosílice proporciona mayores resistencias a compresión que la microsílice, sin embargo las mezclas binarias con bajas proporciones de adición producen mayores resistencias. Por otra parte, se observó mediante la determinación de las relaciones de gel/portlandita, que las mezclas que contienen nanosílice tienen una mayor actividad puzolánica que las que contienen microsílice. En las mezclas binarias se obtuvo como resultado que mientras mayor es el contenido de nanosílice en la mezcla mayor es la actividad puzolánica. Unido a lo anteriormente expuesto, el estudio de la porosidad da como resultado que la adición de nanosílice genera un refinamiento del tamaño de los poros mientras que la adición de microsílice disminuye la cantidad de los mismos sin variar el tamaño de poro medio. Por su parte, en las micrografías, se visualizó la formación de cristales procedentes de la hidratación del cemento. En ellas, se pudo observar, que al adicionar nanosílice, la velocidad de hidratación aumenta al aumentar la formación de monosulfoaluminatos con escasa presencia de etringita. Mientras que en las mezclas con adición de microsílice se observan mayor cantidad de cristales de etringita, lo que confirma que la velocidad de hidratación en estos últimos fue menor. Mediante el estudio de los resultados de las pruebas de durabilidad, se observó que no hay diferencias significativas entre el coeficiente de migración de cloruros y el coeficiente de difusión de cloruros en hormigones con adición de nano o microsílice. Aunque este coeficiente es ligeramente menor en mezclas con adición de microsílice. Sin embargo, en las mezclas binarias de ambas adiciones se obtuvo valores de los coeficientes de difusión o migración de cloruros inferiores a los obtenidos en mezclas con una única adición. Esto se evidencia en los resultados de las pruebas de resistividad eléctrica, de difusión de cloruros y de migración de cloruros. Esto puede ser debido a la suma de los efectos que producen el nano y micro adiciones en la porosidad. El resultado mostró que nanosílice tiene un papel importante en la reducción de los poros y la microsílice disminuye el volumen total de ellos. Esto permite definir la vida útil de estos hormigones a valores muy superiores a los exigidos por la EHE-08, por lo que es posible reducir, de forma notable, el recubrimiento exigido en ambiente de alta agresividad asegurando un buen comportamiento en servicio. Por otra parte, la pérdida de masa debido a los ciclos de congelación-descongelación es significativamente menor en los hormigones que contienen nanosílice que los que contienen microsílice. Este resultado está de acuerdo con el ensayo de absorción capilar. De manera general, se puede concluir que son las mezclas binarias y más concretamente la mezcla con un 5% de nanosílice y 2,5% de microsílice la que presenta los mejores resultados tanto en su comportamiento resistente con en su comportamiento durable. Esto puede ser debido a que en estas mezclas la nanosílice se comporta como un núcleo de activación de las reacciones puzolánicas rodeado de partículas de mayor tamaño. Además, el extraordinario comportamiento durable puede deberse también a la continuidad en la curva granulométrica por la existencia de la microsílice, el filler calizo, el cemento, la arena y la gravilla con tamaños de partículas que garantice mezclas muy compactas que presentan elevadas prestaciones. Since the middle of the decade of the 80 is being investigated about self-consolidating concrete. Every day, its use in the world of construction is more common due to their numerous advantages as its excellent fluidity such that it can flow under its own weight and fill formworks with complicated shapes and congested reinforcement without need for internal or external compactions. Moreover, the search for more resistant and durable materials, has led to the incorporation of additions to cement-based materials. In the last two decades, trials with nanomaterials, has experienced a large increase. The results so far obtained can assume not only an increase in the resistance of these materials but a change is its functionality. These nano particles, particularly the nano silica, not only improve their mechanical properties and especially its durable properties, but that may imply a substantial change in the conditions of use and in their life cycle. This work has as its main objective the study of the mechanical properties, the microstructural characteristics and durability capacity in one self-compacting concrete, when added as addition to cement: nano silica, micro silica o binary mixtures of both. To this effect, 10 concrete mixes have been made. As reference one with a certain amount of cement, limestone filler, viscosity modifying additive and water/binder relation. Furthermore they were manufactured with the same dosage three mix with addition of 2.5%, 5% and 7.5% of nano silica by weight of cement. Other three with 2.5%, 5% and 7.5% of micro silica and the remaining three with binary mixtures of 2.5%-2.5%, 5%-2.5% and 2.5%-5% of silica nano-micro silica respectively, b weight of cement, varying only the amount of superplasticizer to obtain concrete with characteristics of self-compactability. To observe the effects of the additions added to the concrete, an extensive experimental campaign was performed. It assessed, first, the characteristics of self-compactability of fresh material through the tests prescribed in the Spanish Structural Instruction Concrete EHE 08. The mechanical properties were evaluated by compression strength tests, indirect tensile strength and modulus of elasticity. The microstructural properties were analyzed by mercury intrusion porosimetry, thermogravimetric analysis and scanning electron microscopy. To study the durability, were performed electrical resistivity tests, migration and diffusion of chlorides, accelerated carbonation, capillary suction and resistance to freeze-thaw cycles. The results show that the action of the additions generates improvements in the strength properties of the material. Specifically, the addition of nano silica provides greater resistance to compression that the mix with micro silica, however binary mixtures with low addition rates generate higher strengths. Moreover, it was observed by determining relationships gel/portlandite, that the pozzolanic activity in the mixtures with nano silica was higher than in the mixtures with micro silica. In binary mixtures it was found that the highest content of nano silica in the mix is the one with the highest pozzolanic activity. Together with the foregoing, the study of the porosity results in the mixture with addition of nano silica generates a refinement of pore size while adding micro silica decreases the amount thereof without changing the average pore size. On the other hand, in the micrographs, the formation of crystals of cement hydration was visualized. In them, it was observed that by adding nano silica, the speed of hydration increases with increasing formation monosulfoaluminatos with scarce presence of ettringite. While in mixtures with addition of micro silica, ettringite crystals are observed, confirming that the hydration speed was lower in these mixtures. By studying the results of durability testing, it observed that no significant differences between the coefficient of migration of chlorides and coefficient of diffusion of chlorides in concretes with addition of nano or micro silica. Although this coefficient is slightly lower in mixtures with addition of micro silica. However, in binary mixtures of both additions was obtained values of coefficients of difusion o migration of chlorides lower than those obtained in mixtures with one of the additions. This is evidenced by the results of the tests electrical resistivity, diffusion of chlorides and migration of chlorides. This may be due to the sum of the effects that produced the nano and micro additions in the porosity. The result showed that nano silica has an important role in the pores refining and the micro silica decreases the total volume of them. This allows defining the life of these concretes in values to far exceed those required by the EHE-08, making it possible to reduce, significantly, the coating required in highly aggressive environment and to guarantee good behavior in service. Moreover, the mass loss due to freeze-thaw cycles is significantly lower in concretes containing nano silica than those containing micro silica. This result agrees with the capillary absorption test. In general, one can conclude that the binary mixture and more specifically the mixture with 5% of nano silica and 2.5% silica fume is which presents the best results in its durable behavior. This may be because in these mixtures, the nano silica behaves as cores activation of pozzolanic reactions. In addition, the durable extraordinary behavior may also be due to the continuity of the grading curve due to existence of micro silica, limestone filler, cement, sand and gravel with particle sizes that guarantees very compact mixtures which have high performance.

Produção e caracterização de biomateriais acelulares bioativos obtidos a partir da decelularização de placentas

A bioengenharia de tecidos baseia-se no uso de moléculas bioativas, células-tronco e biomateriais para reparação de tecidos e/ou órgãos. Biomateriais podem ser classificados de acordo com sua origem em sintéticos ou biológicos. Biomateriais biológicos podem ser produzidos por decelularização, que visa a remoção de células da matriz extracelular (MEC), a qual deve manter sua integridade química e física. Placentas são órgãos de grande interesse na bioengenharia de tecidos visto que são descartadas após o parto e possuem grande volume de matriz extracelular. Métodos de decelularização podem ser classificados em químicos, físicos e enzimáticos. Todos conhecidamente causam alterações na MEC, sendo que a associação deles é comumente utilizada. Este trabalho comparou diferentes protocolos e estabeleceu um método mais favorável para a decelularização de placentas caninas, visando a produção de um biomaterial para futuras aplicações clínicas. Inicialmente ambas as porções - materna e fetal - das placentas foram submetidas à 10 protocolos, que avaliaram variáveis como concentração e tempo de incubação em detergentes, diferentes gradientes de temperatura e a influência da perfusão versus imersão das soluções, na MEC remanescente. Com base na transparência do tecido e na ausência de núcleo celular em cortes histológicos, dois protocolos foram selecionados (I e II). Além dos critérios já mencionados, ambos os protocolos foram comparados quanto à quantidade de DNA remanescente na MEC decelularizada e à permanência e distribuição de algumas das proteínas da matriz. O detergente SDS foi o mais eficaz na remoção de células, embora não tenha sido suficiente para promover uma decelularização tecidual completa. O congelamento prévio das placentas requereu um maior tempo de incubação posterior das amostras nos distintos detergentes. Ambos métodos de perfusão e imersão foram eficazes na remoção das células, embora grande concentração de proteínas do citoesqueleto tenham permanecido retidas na matriz. As amostras processadas pelo protocolo I (SDS 1%, 5mM EDTA + 50mM TRIS + 0,5% antibiótico, e Triton X-100 1%) apresentaram maior preservação da organização estrutural da MEC quando comparadas àquelas processadas de acordo com o protocolo II (que diferiu do anterior pela utilização de solução contendo 0,05% tripsina ao invés de 50mM TRIS), esse último método entretanto foi o que melhor removeu as células das placentas, conforme observado em lâminas histológicas e demonstrado pela menor concentração de DNA. Tanto as porções materna quanto fetal submetidas à ambos protocolos, mantiveram as proteínas laminina, fibronectina e colágeno tipo I. O colágeno tipo III foi observado somente na porção fetal. Conclui-se que o protocolo II foi o mais eficaz no processo de decelularização de placentas caninas tendo promovido a remoção do conteúdo celular e diminuição da concentração de DNA na MEC remanescente. No entanto é necessário otimizar o tempo de incubação das placentas em soluções enzimáticas visando maior conservação do arranjo da matriz decelularizada. A análise da capacidade da MEC decelularizada por tal método para ser utilizada em bioengenharia de tecidos ainda deve ser avaliada in vitro e in vivo

Administration routes affect the quality of immune responses:a cross-sectional evaluation of particulate antigen-delivery systems

Particulate delivery systems such as liposomes and polymeric nano- and microparticles are attracting great interest for developing new vaccines. Materials and formulation properties essential for this purpose have been extensively studied, but relatively little is known about the influence of the administration route of such delivery systems on the type and strength of immune response elicited. Thus, the present study aimed at elucidating the influence on the immune response when of immunising mice by different routes, such as the subcutaneous, intradermal, intramuscular, and intralymphatic routes with ovalbumin-loaded liposomes, N-trimethyl chitosan (TMC) nanoparticles, and poly(lactide-co-glycolide) (PLGA) microparticles, all with and without specifically selected immune-response modifiers. The results showed that the route of administration caused only minor differences in inducing an antibody response of the IgG1 subclass, and any such differences were abolished upon booster immunisation with the various adjuvanted and non-adjuvanted delivery systems. In contrast, the administration route strongly affected both the kinetics and magnitude of the IgG2a response. A single intralymphatic administration of all evaluated delivery systems induced a robust IgG2a response, whereas subcutaneous administration failed to elicit a substantial IgG2a response even after boosting, except with the adjuvanted nanoparticles. The intradermal and intramuscular routes generated intermediate IgG2a titers. The benefit of the intralymphatic administration route for eliciting a Th1-type response was confirmed in terms of IFN-gamma production of isolated and re-stimulated splenocytes from animals previously immunised with adjuvanted and non-adjuvanted liposomes as well as with adjuvanted microparticles. Altogether the results show that the IgG2a associated with Th1-type immune responses are sensitive to the route of administration, whereas IgG1 response associated with Th2-type immune responses were relatively insensitive to the administration route of the particulate delivery systems. The route of administration should therefore be considered when planning and interpreting pre-clinical research or development on vaccine delivery systems.

Analytical model for active metamaterials with quantum ingredients

We present an analytical model for describing complex dynamics of a hybrid system consisting of resonantly coupled classical resonator and quantum structures. Classical resonators in our model correspond to plasmonic metamaterials of various geometries, as well as other types of nano- and microstructure, the optical responses of which can be described classically. Quantum resonators are represented by atoms or molecules, or their aggregates (for example, quantum dots, carbon nanotubes, dye molecules, polymer or bio-molecules etc), which can be accurately modelled only with the use of the quantum mechanical approach. Our model is based on the set of equations that combines well established density matrix formalism appropriate for quantum systems, coupled with harmonic-oscillator equations ideal for modelling sub-wavelength plasmonic and optical resonators. As a particular example of application of our model, we show that the saturation nonlinearity of carbon nanotubes increases multifold in the resonantly enhanced near field of a metamaterial. In the framework of our model, we discuss the effect of inhomogeneity of the carbon-nanotube layer (bandgap value distribution) on the nonlinearity enhancement. © 2012 IOP Publishing Ltd.