Mechanical properties of cold-formed steels at elevated temperatures

Mechanical properties have an important role in the fire safety design of cold-formed steel structures due to the rapid reduction in mechanical properties such as yield strength and elastic modulus under fire conditions and associated reduction to the load carrying capacities. Hence there is a need to fully understand the deterioration characteristics of yield strength and elastic modulus of cold-formed steels at elevated temperatures. Although past research has produced useful experimental data on the mechanical properties of cold-formed steels at elevated temperatures, such data do not yet cover different cold-formed steel grades and thicknesses. Therefore, an experimental study was undertaken to investigate the elevated temperature mechanical properties of two low and high strength steels with two thicknesses that are commonly used in Australia. Tensile coupon tests were undertaken using a steady state test method for temperatures in the range 20–700 °C. Test results were compared with the currently available reduction factors for yield strength and elastic modulus, and stress–strain curves, based on which further improvements were made. For this purpose, test results of many other cold-formed steels were also used based on other similar studies undertaken at the Queensland University of Technology. Improved equations were developed to predict the yield strength and elastic modulus reduction factors and stress–strain curves of a range of cold-formed steel grades and thicknesses used in Australia. This paper presents the results of this experimental study, comparisons with the results of past research and steel design standards, and the new predictive equations.

The 'nurdle to leg' and other ways of winning cricket matches

The emergence of Twenty20 cricket at the elite level has been marketed on the excitement of the big hitter, where it seems that winning is a result of the muscular batter hitting boundaries at will. This version of the game has captured the imagination of many young players who all want to score runs with “big hits”. However, in junior cricket, boundary hitting is often more difficult due to size limitations of children and games played on outfields where the ball does not travel quickly. As a result, winning is often achieved via a less spectacular route – by scoring more singles than your opponents. However, most standard coaching texts only describe how to play boundary scoring shots (e.g. the drives, pulls, cuts and sweeps) and defensive shots to protect the wicket. Learning to bat appears to have been reduced to extremes of force production, i.e. maximal force production to hit boundaries or minimal force production to stop the ball from hitting the wicket. Initially, this is not a problem because the typical innings of a young player (<12 years) would be based on the concept of “block” or “bash” – they “block” the good balls and “bash” the short balls. This approach works because there are many opportunities to hit boundaries off the numerous inaccurate deliveries of novice bowlers. Most runs are scored behind the wicket by using the pace of the bowler’s delivery to re-direct the ball, because the intrinsic dynamics (i.e. lack of strength) of most children means that they can only create sufficient power by playing shots where the whole body can contribute to force production. This method works well until the novice player comes up against more accurate bowling when they find they have no way of scoring runs. Once batters begin to face “good” bowlers, batters have to learn to score runs via singles. In cricket coaching manuals (e.g. ECB, n.d), running between the wickets is treated as a separate task to batting, and the “basics” of running, such as how to “back- up”, carry the bat, calling and turning and sliding the bat into the crease are “drilled” into players. This task decomposition strategy focussing on techniques is a common approach to skill acquisition in many highly traditional sports, typified in cricket by activities where players hit balls off tees and receive “throw-downs” from coaches. However, the relative usefulness of these approaches in the acquisition of sporting skills is increasingly being questioned (Pinder, Renshaw & Davids, 2009). We will discuss why this is the case in the next section.

Developing the atlas of cancer in Queensland : methodological issues

Background: Achieving health equity has been identified as a major challenge, both internationally and within Australia. Inequalities in cancer outcomes are well documented, and must be quantified before they can be addressed. One method of portraying geographical variation in data uses maps. Recently we have produced thematic maps showing the geographical variation in cancer incidence and survival across Queensland, Australia. This article documents the decisions and rationale used in producing these maps, with the aim to assist others in producing chronic disease atlases. Methods: Bayesian hierarchical models were used to produce the estimates. Justification for the cancers chosen, geographical areas used, modelling method, outcome measures mapped, production of the adjacency matrix, assessment of convergence, sensitivity analyses performed and determination of significant geographical variation is provided. Conclusions: Although careful consideration of many issues is required, chronic disease atlases are a useful tool for assessing and quantifying geographical inequalities. In addition they help focus research efforts to investigate why the observed inequalities exist, which in turn inform advocacy, policy, support and education programs designed to reduce these inequalities.

Scaling of free convection heat transfer in a triangular cavity for Pr>1

Unsteady natural convection inside a triangular cavity subject to a non-instantaneous heating on the inclined walls in the form of an imposed temperature which increases linearly up to a prescribed steady value over a prescribed time is reported. The development of the flow from start-up to a steady-state has been described based on scaling analyses and direct numerical simulations. The ramp temperature has been chosen in such a way that the boundary layer is reached a quasi-steady mode before the growth of the temperature is completed. In this mode the thermal boundary layer at first grows in thickness, then contracts with increasing time. However, if the imposed wall temperature growth period is sufficiently short, the boundary layer develops differently. It is seen that the shape of many houses are isosceles triangular cross-section. The heat transfer process through the roof of the attic-shaped space should be well understood. Because, in the building energy, one of the most important objectives for design and construction of houses is to provide thermal comfort for occupants. Moreover, in the present energy-conscious society it is also a requirement for houses to be energy efficient, i.e. the energy consumption for heating or air-conditioning houses must be minimized.

Evaluation of texture and geometry for dimensional facial expression recognition

Facial expression recognition (FER) algorithms mainly focus on classification into a small discrete set of emotions or representation of emotions using facial action units (AUs). Dimensional representation of emotions as continuous values in an arousal-valence space is relatively less investigated. It is not fully known whether fusion of geometric and texture features will result in better dimensional representation of spontaneous emotions. Moreover, the performance of many previously proposed approaches to dimensional representation has not been evaluated thoroughly on publicly available databases. To address these limitations, this paper presents an evaluation framework for dimensional representation of spontaneous facial expressions using texture and geometric features. SIFT, Gabor and LBP features are extracted around facial fiducial points and fused with FAP distance features. The CFS algorithm is adopted for discriminative texture feature selection. Experimental results evaluated on the publicly accessible NVIE database demonstrate that fusion of texture and geometry does not lead to a much better performance than using texture alone, but does result in a significant performance improvement over geometry alone. LBP features perform the best when fused with geometric features. Distributions of arousal and valence for different emotions obtained via the feature extraction process are compared with those obtained from subjective ground truth values assigned by viewers. Predicted valence is found to have a more similar distribution to ground truth than arousal in terms of covariance or Bhattacharya distance, but it shows a greater distance between the means.

Validating a model of cooperative procurement in the construction industry

Project management in the construction industry involves coordination of many tasks and individuals, affected by complexity and uncertainty, which increases the need for efficient cooperation. Procurement is crucial since it sets the basis for cooperation between clients and contractors. This is true whether the project is local, regional or global in scope. Traditionally, procurement procedures are competitive, resulting in conflicts, adversarial relationships and less desirable project results. The purpose of this paper is to propose and empirically test an alternative procurement model based on cooperative procurement procedures that facilitates cooperation between clients and contractors in construction projects. The model is based on four multi-item constructs – incentive-based compensation, limited bidding options, partner selection and cooperation. Based on a sample of 87 client organisations, the model was empirically tested and exhibited strong support, including content, nomological, convergent and discriminant validity, as well as reliability. Our findings indicate that partner selection based on task related attributes mediates the relationship between two important pre-selection processes (incentive-based compensation and limited bid invitation) and preferred outcome of cooperation. The contribution of the paper is identifying valid and reliable measurement constructs and confirming a unique sequential order for achieving cooperation. Moreover, the findings are applicable for many types of construction projects because of the similarities in the construction industry worldwide.

Action inquiry into the use of standardized evaluation tools for music therapy : a real life journey within a parent-child community program

Sing & Grow is an early intervention music therapy project that provides community group music therapy programs to families with young children who encounter risk factors that may impact on parenting and optimal child develop variety of evaluation tools were devised and used over the first 3 years of the project. Upon the subsequent funding and expansion of the project at the end of this period, it was necessary to find, test and devise more rigorous, valid and reliable measures to withstand the scrutiny of researchers, and to combat the concerns and criticisms associated with the previous methods of data collection. An action inquiry project was therefore undertaken with two groups of project participants to trial the use of the Parenting Stress Index and Depression, Anxiety and Stress Scales, both recommended by leading psychologists. Key findings that will be discussed include the friction between the deficit-focussed nature of many psychometric tools and the strengths-based approach taken in service delivery, the level of difficulty in terms of literacy and comprehension for vulnerable respondents, and the lack of one tool with the ability to comprehensively measure all aspects of a broad scoping program. Keywords: music therapy, evaluation, PSI, DASS, action inquiry.

An exploration of the technical, social and macro-societal pressures influencing the adoption of online social networking services by organisations

Measuring the business value that Internet technologies deliver for organisations has proven to be a difficult and elusive task, given their complexity and increased embeddedness within the value chain. Yet, despite the lack of empirical evidence that links the adoption of Information Technology (IT) with increased financial performance, many organisations continue to adopt new technologies at a rapid rate. This is evident in the widespread adoption of Web 2.0 online Social Networking Services (SNSs) such as Facebook, Twitter and YouTube. These new Internet based technologies, widely used for social purposes, are being employed by organisations to enhance their business communication processes. However, their use is yet to be correlated with an increase in business performance. Owing to the conflicting empirical evidence that links prior IT applications with increased business performance, IT, Information Systems (IS), and E-Business Model (EBM) research has increasingly looked to broader social and environmental factors as a means for examining and understanding the broader influences shaping IT, IS and E-Business (EB) adoption behaviour. Findings from these studies suggest that organisations adopt new technologies as a result of strong external pressures, rather than a clear measure of enhanced business value. In order to ascertain if this is the case with the adoption of SNSs, this study explores how organisations are creating value (and measuring that value) with the use of SNSs for business purposes, and the external pressures influencing their adoption. In doing so, it seeks to address two research questions: 1. What are the external pressures influencing organisations to adopt SNSs for business communication purposes? 2. Are SNSs providing increased business value for organisations, and if so, how is that value being captured and measured? Informed by the background literature fields of IT, IS, EBM, and Web 2.0, a three-tiered theoretical framework is developed that combines macro-societal, social and technological perspectives as possible causal mechanisms influencing the SNS adoption event. The macro societal view draws on the concept of Castells. (1996) network society and the behaviour of crowds, herds and swarms, to formulate a new explanatory concept of the network vortex. The social perspective draws on key components of institutional theory (DiMaggio & Powell, 1983, 1991), and the technical view draws from the organising vision concept developed by Swanson and Ramiller (1997). The study takes a critical realist approach, and conducts four stages of data collection and one stage of data coding and analysis. Stage 1 consisted of content analysis of websites and SNSs of many organisations, to identify the types of business purposes SNSs are being used for. Stage 2 also involved content analysis of organisational websites, in order to identify suitable sample organisations in which to conduct telephone interviews. Stage 3 consisted of conducting 18 in-depth, semi-structured telephone interviews within eight Australian organisations from the Media/Publishing and Galleries, Libraries, Archives and Museum (GLAM) industries. These sample organisations were considered leaders in the use of SNSs technologies. Stage 4 involved an SNS activity count of the organisations interviewed in Stage 3, in order to rate them as either Advanced Innovator (AI) organisations, or Learning Focussed (LF) organisations. A fifth stage of data coding and analysis of all four data collection stages was conducted, based on the theoretical framework developed for the study, and using QSR NVivo 8 software. The findings from this study reveal that SNSs have been adopted by organisations for the purpose of increasing business value, and as a result of strong social and macro-societal pressures. SNSs offer organisations a wide range of value enhancing opportunities that have broader benefits for customers and society. However, measuring the increased business value is difficult with traditional Return On Investment (ROI) mechanisms, ascertaining the need for new value capture and measurement rationales, to support the accountability of SNS adoption practices. The study also identified the presence of technical, social and macro-societal pressures, all of which influenced SNS adoption by organisations. These findings contribute important theoretical insight into the increased complexity of pressures influencing technology adoption rationales by organisations, and have important practical implications for practice, by reflecting the expanded global online networks in which organisations now operate. The limitations of the study include the small number of sample organisations in which interviews were conducted, its limited generalisability, and the small range of SNSs selected for the study. However, these were compensated in part by the expertise of the interviewees, and the global significance of the SNSs that were chosen. Future research could replicate the study to a larger sample from different industries, sectors and countries. It could also explore the life cycle of SNSs in a longitudinal study, and map how the technical, social and macro-societal pressures are emphasised through stages of the life cycle. The theoretical framework could also be applied to other social fad technology adoption studies.

Investigation of the effect of organics on the water uptake of marine aerosols

Water uptake refers to the ability of atmospheric particles to take up water vapour from the surrounding atmosphere. This is an important property that affects particle size and phase and therefore influences many characteristics of aerosols relevant to air quality and climate. However, the water uptake properties of many important atmospheric aerosol systems, including those related to the oceans, are still not fully understood. Therefore, the primary aim of this PhD research program was to investigate the water uptake properties of marine aerosols. In particular, the effect of organics on marine aerosol water uptake was investigated. Field campaigns were conducted at remote coastal sites on the east coast of Australia (Agnes Water; March-April 2007) and west coast of Ireland (Mace Head; June 2007), and laboratory measurements were performed on bubble-generated sea spray aerosols. A combined Volatility-Hygroscopicity-Tandem Differential Mobility Analyser (VH-TDMA) was employed in all experiments. This system probes the changes in the hygroscopic properties of nanoparticles as volatile organic components are progressively evaporated. It also allows particle composition to be inferred from combined volatility-hygroscopicity measurements. Frequent new particle formation and growth events were observed during the Agnes Water campaign. The VH-TDMA was used to investigate freshly nucleated particles (17-22.5 nm) and it was found that the condensation of sulphate and/or organic vapours was responsible for driving particle growth during the events. Aitken mode particles (~40 nm) were also measured with the VH-TDMA. In 3 out of 18 VH-TDMA scans evaporation of a volatile, organic component caused a very large increase in hygroscopicity that could only be explained by an increase in the absolute water uptake of the particle residuals, and not merely an increase in their relative hygroscopicity. This indicated the presence of organic components that were suppressing the hygroscopic growth of mixed particles on the timescale of humidification in the VH-TDMA (6.5 secs). It was suggested that the suppression of water uptake was caused by either a reduced rate of hygroscopic growth due to the presence of organic films, or organic-inorganic interactions in solution droplets that had a negative effect on hygroscopicity. Mixed organic-inorganic particles were rarely observed by the VH-TDMA during the summer campaign conducted at Mace Head. The majority of particles below 100 nm in clean, marine air appeared to be sulphates neutralised to varying degrees by ammonia. On one unique day, 26 June 2007, particularly large concentrations of sulphate aerosol were observed and identified as volcanic emissions from Iceland. The degree of neutralisation of the sulphate aerosol by ammonia was calculated by the VH-TDMA and found to compare well with the same quantity measured by an aerosol mass spectrometer. This was an important verification of the VH-TMDA‘s ability to identify ammoniated sulphate aerosols based on the simultaneous measurement of aerosol volatility and hygroscopicity. A series of measurements were also conducted on sea spray aerosols generated from Moreton Bay seawater samples in a laboratory-based bubble chamber. Accumulation mode sea spray particles (38-173 nm) were found to contain only a minor organic fraction (< 10%) that had little effect on particle hygroscopicity. These results are important because previous studies have observed that accumulation mode sea spray particles are predominantly organic (~80% organic mass fraction). The work presented here suggests that this is not always the case, and that there may be currently unknown factors that are controlling the transfer of organics to the aerosol phase during the bubble bursting process. Taken together, the results of this research program have significantly improved our understanding of organic-containing marine aerosols and the way they interact with water vapour in the atmosphere.

The influence of ambient temperature on birth outcomes in Brisbane, Australia

Lately, there has been increasing interest in the association between temperature and adverse birth outcomes including preterm birth (PTB) and stillbirth. PTB is a major predictor of many diseases later in life, and stillbirth is a devastating event for parents and families. The aim of this study was to assess the seasonal pattern of adverse birth outcomes, and to examine possible associations of maternal exposure to temperature with PTB and stillbirth. We also aimed to identify if there were any periods of the pregnancy where exposure to temperature was particularly harmful. A retrospective cohort study design was used and we retrieved individual birth records from the Queensland Health Perinatal Data Collection Unit for all singleton births (excluding twins and triplets) delivered in Brisbane between 1 July 2005 and 30 June 2009. We obtained weather data (including hourly relative humidity, minimum and maximum temperature) and air-pollution data (including PM10, SO2 and O3) from the Queensland Department of Environment and Resource Management. We used survival analyses with the time-dependent variables of temperature, humidity and air pollution, and the competing risks of stillbirth and live birth. To assess the monthly pattern of the birth outcomes, we fitted month of pregnancy as a time-dependent variable. We examined the seasonal pattern of the birth outcomes and the relationship between exposure to high or low temperatures and birth outcomes over the four lag weeks before birth. We further stratified by categorisation of PTB: extreme PTB (< 28 weeks of gestation), PTB (28–36 weeks of gestation), and term birth (≥ 37 weeks of gestation). Lastly, we examined the effect of temperature variation in each week of the pregnancy on birth outcomes. There was a bimodal seasonal pattern in gestation length. After adjusting for temperature, the seasonal pattern changed from bimodal, to only one peak in winter. The risk of stillbirth was statistically significant lower in March compared with January. After adjusting for temperature, the March trough was still statistically significant and there was a peak in risk (not statistically significant) in winter. There was an acute effect of temperature on gestational age and stillbirth with a shortened gestation for increasing temperature from 15 °C to 25 °C over the last four weeks before birth. For stillbirth, we found an increasing risk with increasing temperatures from 12 °C to approximately 20 °C, and no change in risk at temperatures above 20 °C. Certain periods of the pregnancy were more vulnerable to temperature variation. The risk of PTB (28–36 weeks of gestation) increased as temperatures increased above 21 °C. For stillbirth, the fetus was most vulnerable at less than 28 weeks of gestation, but there were also effects in 28–36 weeks of gestation. For fetuses of more than 37 weeks of gestation, increasing temperatures did not increase the risk of stillbirth. We did not find any adverse affects of cold temperature on birth outcomes in this cohort. My findings contribute to knowledge of the relationship between temperature and birth outcomes. In the context of climate change, this is particularly important. The results may have implications for public health policy and planning, as they indicate that pregnant women would decrease their risk of adverse birth outcomes by avoiding exposure to high temperatures and seeking cool environments during hot days.

Social Procurement: Promoting the sustainability of NPOs through the transformation of economic, social and cultural capital

Social procurement provides a key source of income for the Third Sector, and is vital for the sustainability of many nonprofit organisations. Social procurement involves the exchange of economic capital from one organisation, typically government (although for-profit and non-profit organisations can also purchase), with a nonprofit organisations in order to deliver other forms of. It is this transformation of economic capital into other forms of capital (cultural, human, social) in the social procurement process, which is the focus of this paper. Four case studies, which are representative of the four main types of social procurement, will be examined in order to trace how economic capital is transformed into other types of capital in each of these cases. In so doing, the paper will advance our understanding of social procurement theoretically, and lead to a wider discussion about the role of social procurement in ensuring the sustainability of nonprofit organisations, and the civil societies in which they operate.

The Use of Social Technology to Support Organisational Knowledge

In the current economy, knowledge has been recognized to be a valuable organisational asset, a crucial factor that aids organisations to succeed in highly competitive environments. Many organisations have begun projects and special initiatives aimed at fostering better knowledge sharing amongst their employees. Not surprisingly, information technology (IT) has been a central element of many of these projects and initiatives, as the potential of emerging information technologies such as Web 2.0 for enabling the process of managing organisational knowledge is recognised. This technology could be used as a collaborative system for knowledge management (KM) within enterprises. Enterprise 2.0 is the application of Web 2.0 in an organisational context. Enterprise 2.0 technologies are web-based social software that facilitate collaboration, communication and information flow in a bidirectional manner: an essential aspect of organisational knowledge management. This chapter explains how Enterprise 2.0 technologies (Web 2.0 technologies within organisations) can support knowledge management. The chapter also explores how such technologies support the codifying (technology-centred) and social network (people-centred) approaches of KM, towards bridging the current gap between these two approaches.

Impact of a data warehouse model for improved decision-making process in healthcare

The health system is one sector dealing with a deluge of complex data. Many healthcare organisations struggle to utilise these volumes of health data effectively and efficiently. Also, there are many healthcare organisations, which still have stand-alone systems, not integrated for management of information and decision-making. This shows, there is a need for an effective system to capture, collate and distribute this health data. Therefore, implementing the data warehouse concept in healthcare is potentially one of the solutions to integrate health data. Data warehousing has been used to support business intelligence and decision-making in many other sectors such as the engineering, defence and retail sectors. The research problem that is going to be addressed is, "how can data warehousing assist the decision-making process in healthcare". To address this problem the researcher has narrowed an investigation focusing on a cardiac surgery unit. This research used the cardiac surgery unit at the Prince Charles Hospital (TPCH) as the case study. The cardiac surgery unit at TPCH uses a stand-alone database of patient clinical data, which supports clinical audit, service management and research functions. However, much of the time, the interaction between the cardiac surgery unit information system with other units is minimal. There is a limited and basic two-way interaction with other clinical and administrative databases at TPCH which support decision-making processes. The aims of this research are to investigate what decision-making issues are faced by the healthcare professionals with the current information systems and how decision-making might be improved within this healthcare setting by implementing an aligned data warehouse model or models. As a part of the research the researcher will propose and develop a suitable data warehouse prototype based on the cardiac surgery unit needs and integrating the Intensive Care Unit database, Clinical Costing unit database (Transition II) and Quality and Safety unit database [electronic discharge summary (e-DS)]. The goal is to improve the current decision-making processes. The main objectives of this research are to improve access to integrated clinical and financial data, providing potentially better information for decision-making for both improved from the questionnaire and by referring to the literature, the results indicate a centralised data warehouse model for the cardiac surgery unit at this stage. A centralised data warehouse model addresses current needs and can also be upgraded to an enterprise wide warehouse model or federated data warehouse model as discussed in the many consulted publications. The data warehouse prototype was able to be developed using SAS enterprise data integration studio 4.2 and the data was analysed using SAS enterprise edition 4.3. In the final stage, the data warehouse prototype was evaluated by collecting feedback from the end users. This was achieved by using output created from the data warehouse prototype as examples of the data desired and possible in a data warehouse environment. According to the feedback collected from the end users, implementation of a data warehouse was seen to be a useful tool to inform management options, provide a more complete representation of factors related to a decision scenario and potentially reduce information product development time. However, there are many constraints exist in this research. For example the technical issues such as data incompatibilities, integration of the cardiac surgery database and e-DS database servers and also, Queensland Health information restrictions (Queensland Health information related policies, patient data confidentiality and ethics requirements), limited availability of support from IT technical staff and time restrictions. These factors have influenced the process for the warehouse model development, necessitating an incremental approach. This highlights the presence of many practical barriers to data warehousing and integration at the clinical service level. Limitations included the use of a small convenience sample of survey respondents, and a single site case report study design. As mentioned previously, the proposed data warehouse is a prototype and was developed using only four database repositories. Despite this constraint, the research demonstrates that by implementing a data warehouse at the service level, decision-making is supported and data quality issues related to access and availability can be reduced, providing many benefits. Output reports produced from the data warehouse prototype demonstrated usefulness for the improvement of decision-making in the management of clinical services, and quality and safety monitoring for better clinical care. However, in the future, the centralised model selected can be upgraded to an enterprise wide architecture by integrating with additional hospital units’ databases.

Abduction : the writing of a historical novel

This is a practice-led project consisting of a historical novel Abduction and related exegesis. The novel is a third person intimate narrative set in the mid-nineteenth century and is based on actual events and persons caught up in, or furthering, the mass dispossession of small farmers in Scotland known as the ‘Clearances’. The narrative focuses on the situation in the Outer Hebrides and northern Scotland. It is based on documented facts leading up to a controversial trial in 1850 that arose because a twenty year old woman of the period (the central protagonist, Jess Mackenzie) eloped with a young farmer to escape her parent’s pressure to marry a rival suitor, himself a powerful lawyer and ‘factor’ at the centre of many of the Clearances. The young woman’s independent ideas were ahead of her time, and the decisions she made under great pressure were crucial in some dramatic events that unfolded in Scotland and later in the colony of Victoria, to which she and her new husband emigrated soon after the trial. The exegesis is composed of two unequal parts. It briefly considers the development of the literary historical fiction genre in the nineteenth century with Walter Scott in particular, a genre found useful in representing women’s issues of the Victorian era by Victorian and contemporary authors. The exegesis also briefly considers the appropriateness of the fiction genre (as opposed to creative nonfiction) in creating the lived experience in a fact-based work. The major part of the exegesis is a detailed, reflective analysis of the problem-solving process involved in writing the novel, structured by reference to Kate Grenville’s Searching for the Secret River – a work of metawriting that explains her creative process in researching and writing historical fiction based on fact.

Connecting Diversity : Paradoxes of Multicultural Australia

Commissioned by SBS, and published in March 2006, Connecting Diversity: Paradoxes of Multicultural Australia is a follow-up study to SBS’s 2002 report, Living Diversity: Australia’s Multicultural Future. The attitudes of many younger Australians from culturally diverse backgrounds reveal paradoxes about Australian multiculturalism today. This report sheds light on their views, experiences and expectations and the role of media in their lives. Younger, culturally and linguistically diverse Australians are often the subject of mediafanned controversy about disaffection, ‘ethnic gangs’ and cultural isolation. While these controversies tend to be localised – Cronulla, Inala or Bankstown – Connecting Diversity tells a national and quite different story. This research builds upon the findings of the 2002 report, Living Diversity: Australia’s Multicultural Future, which challenged common assumptions about contemporary multicultural Australia. In an era of fragmenting media and assumed political apathy, Connecting Diversity further examines many of the findings of the earlier study, with a new focus on younger people, cultural identity and media use. Connecting Diversity reveals individual experiences and often contradictory ideas about media and diversity in Australia. Disjunctions appear to exist between an individual’s experience and their thoughts about Australia’s national identity. Multiculturalism is valued for broadening the appreciation of difference, yet this support can coexist with concerns about perceived segregation, usually ‘elsewhere’ in Australia. Younger people tend to be more comfortable with cultural difference than previous generations and cite their own diverse network of friends as one of the reasons for this. Even so, some describe experiences of racism that engender a feeling of exclusion from ‘mainstream’ society. In their everyday lives, social relationships are navigated through regular and familiar connections on the one hand, and experiences and expressions of disconnection on the other. Racism and tolerance may be expressed almost simultaneously. These disconnections are often managed through ‘practical tolerance',allowing them to negotiate these apparent contradictions. The connections can be based simultaneously on such things as work, family,religion, friendships or location. The result is a multilayered sense of personal belonging and community connection. A large number of respondents in these focus groups expressed frustration at the failings of media, especially news and current affairs coverage, yet spoke enthusiastically about the accessibility and range of media compared to what was available to previous generations. In their many forms, media remain a key ingredient of self-identification among younger Australians of culturally diverse backgrounds who are especially cynical about media and disillusioned by their perceived inability to influence issues that are important to them. These findings reveal that although they may be cynical about media messages, these younger Australians are looking for connection through media and are seeking ways to participate in meaningful ways. This raises questions about the possibilities for media to empower younger people to play a part in genuine cultural democracy. By capturing the attitudes of Australians of culturally diverse backgrounds under the age of 40, Connecting Diversity: Paradoxes of Multicultural Australia provides an insight into social trends and the generational and cultural changes that are now shaping Australia.