SURFACTANT-OIL INTERACTIONS: FOAMING & TOXICITY

Surfactants find large applications in detergents, paints, coatings, food and pharmaceutical industries. Other than that, much focused work has been carried out in oil recovery in petroleum industries and raw material extraction in mining industries. This is because of their unique structure and ability to simultaneously adhere to materials which are both structurally and physically different. The current thesis focuses on interactions of oil with different commercially available and laboratory synthesized surfactants in terms of characteristics such as foaming, ultrasound exposure and toxicity. Foaming is one important characteristic of surfactants that is widely utilized for oil recovery purposes. Researchers utilize surfactants' special ability to provide foam stability to for more efficient oil herding capability. The foam stability and foam volumes are calculated using static foam height tests. Further dispersion or oil in water emulsion formation is observed using ultrasound sources. As described earlier surfactants are not only used as foams for oil displacement, but they are also used for dispersion purposes where they are key components of dispersant formulations. During such operations, especially in sea conditions where adverse effects on aquatic life are a concern, toxicity of chemicals used becomes an important factor. Our toxicity testing experiments involves different surfactants, solvents and crude oil combinations through exposure to special light luminescent bacteria. The decrease in light intensity of the exposed bacteria is related to toxic effects of the samples.

Reduction of cement leakage by sequential PMMA application in a vertebroplasty model

PURPOSE Leakage is the most common complication of percutaneous cement augmentation of the spine. The viscosity of the polymethylmethacrylate (PMMA) cement is strongly correlated with the likelihood of cement leakage. We hypothesized that cement leakage can be reduced by sequential cement injection in a vertebroplasty model. METHODS A standardized vertebral body substitute model, consisting of aluminum oxide foams coated by acrylic cement with a preformed leakage path, simulating a ventral vein, was developed. Three injection techniques of 6 ml PMMA were assessed: injection in one single step (all-in-one), injection of 1 ml at the first and 5 ml at the second step with 1 min latency in-between (two-step), and sequential injection of 0.5 ml with 1-min latency between the sequences (sequential). Standard PMMA vertebroplasty cement was used; each injection type was tested on ten vertebral body substitute models with two possible leakage paths per model. Leakage was assessed by radiographs using a zonal graduation: intraspongious = no leakage and extracortical = leakage. RESULTS The leakage rate was significantly lower in the "sequential" technique (2/20 leakages) followed by "two-step" (15/20) and "all-in-one" (20/20) techniques (p < 0.001). The RR for a cement leakage was 10.0 times higher in the "all-in-one" compared to the "sequential" group (95 % confidence intervals 2.7-37.2; p < 0.001). CONCLUSIONS The sequential cement injection is a simple approach to minimize the risk for leakage. Taking advantage of the temperature gradient between body and room temperature, it is possible to increase the cement viscosity inside the vertebra while keeping it low in the syringe. Using sequential injection of small cement volumes, further leakage paths are blocked before further injection of the low-viscosity cement.

Desarrollo, análisis y caracterización de procesos de soldeo térmico de espumas de aluminio

Uno de los retos actuales aún pendiente de lograr trabajando con espumas de aluminio, es el desarrollo de métodos de unión fácilmente reproducibles a nivel industrial que permitan la unión de espumas de aluminio entre sí o con otros componentes tipo pletinas, para así poder fabricar piezas de mayor tamaño o con formas complejas, a la vez que se conserven las propiedades y características principales de las espumas de aluminio, tanto en la zona principal de unión o cordón, como en la interfase y zona afectada térmicamente, que se encuentran anexa. Los actuales procesos de unión más utilizados con espumas de aluminio, se basan principalmente en adhesivos y uniones mecánicas. Estas soluciones a priori válidas, añaden problemas técnicos a determinadas aplicaciones de las espumas que frenan la completa integración de estos materiales en un entorno de fabricación flexible y global. Por esta razón, los actuales procesos de producción de las espumas de aluminio se restringen a determinadas ofertas hechas a la medida del cliente, no pudiendo atender por falta de soluciones, a una gran parte del potencial mercado de estos materiales. En el presente trabajo de investigación se han desarrollado y caracterizado diferentes métodos de unión de espumas de aluminio, en configuración a tope y de espumas de aluminio con pletinas en configuración a solape, basados en procesos por soldeo térmico. One of the current challenges even pending of being achieved working with aluminium foams, is the development of easily reproducible methods at industrial level that allow the joint of aluminium foams between them or with other elements as for example aluminium plates for making bigger pieces or with more complex forms, remaining simultaneously in the weld bead the properties and main characteristics of aluminium foam, so much in the joint area or interface, since in the affected closer thermal zone. Currently, the most used joint processes for applying to aluminium foams are based mainly on adhesives and mechanical joins. These solutions initially valid, add technical problems to certain aluminium foams applications, which stop the complete integration of these materials in a more flexible and global manufacture environment. For this reason, current aluminium foam manufacturing processes are restricted to certain offers done to a specific customer requirement, not being able to attend for lack of available solutions, to a great potential market of these materials. In the present work, different joint methods between aluminium foams and between aluminium foams and plates for butt and lap configurations have been developed and characterized based on thermal welding processes.

Estudio del comportamiento mecánico de las espumas pulvimetalúrgicas de aluminio

Con este trabajo se pretende determinar la relación entre las características físicas y mecánicas y la estructura para espumas de aluminio de Al12Si y AA6061 obtenidas por pulvimetalurgia utilizando probetas prismáticas de dimensiones diecisiete por diecisiete por sesenta milímetros. De su estudio mecánico y de análisis de imagen se concluye que las probetas cuyas propiedades físicas y mecánicas están moderadamente por encima de la media poseen mayor número de poros medianos y paredes de poro más gruesas. Por el contrario, las propiedades resultan inferiores cuando se presentan estructuras con un mayor número de poros medianos. Aquellas espumas con estructuras obtenidas por una espumación incompleta presentan una menor porosidad y por ello mayores densidades. En aquellos casos donde la estructura presenta una elevada presencia de poros grandes, sus propiedades mecánicas disminuyen. ABSTRACT With this work we are trying to determine the relation between physical and mechanical characteristics and its structure, for Al12Si and AA6061 aluminium foams, obtained by podwer metallurgy. Aluminium foam samples with dimensions of seventeen per seventeen per sixty millimeters were used. After its mechanical and image analysis study, we conclude that samples whose physical and mechanical properties are moderately over the average, they have a major proportion of medium pores and thicker pore walls. Otherwise, properties result to be inferior when a major number of medium pores structures are presented. Those foam structures obtained with an incomplete foaming process show a lower porosity, and so higher densities. Also, properties decrease in those cases in which the structure presents a high presence of big pores.

Absorción acústica a incidencia normal de espumas de aluminio

En este artículo se presentan los primeros resultados de absorción acústica a incidencia normal de espumas de aluminio fabricadas mediante una técnica pulvimetalúrgica. El interés de estas espumas radica en que en ellas se combinan interesantes propiedades acústicas y mecánicas. Se estudian espumas de aluminio de distinta morfología superficial conseguida variando el tipo de precursor y usando materiales de relleno durante el proceso de espumación. Se muestra un estudio comparativo de las espumas fabricadas mediante esta técnica con las espumas comerciales ALPORAS. Las espumas de menor densidad presentan una absorción acústica comparable a la de las comerciales ALPORAS. ABSTRACT. In this paper, the first experimental data of acoustic absorption at normal incidence in aluminum foams generated by a metallurgic technique are presented. The interest of this kind of structures is due to the combination of mechanical and acoustic properties. By changing the precursor type or using filling materials during the foaming process, we have obtained aluminum foams with different surface morphologies. A comparative study between foams fabricated using this technique and ALPORAS commercial aluminum foams is shown. The foams which present the lower density show an acoustic absorption comparable to the ALPORAS commercial ones.

MRI and Bidimensional relaxometry sequences for macro and microstructure assessment in food models.

Physico-chemical and organoleptic characteristics of food depend largely on the microscopic level distribution of gases and water, and connectivity and mobility through the pores. Microstructural characterization of food can be accomplished by Magnetic Resonance Imaging (MRI) and Nuclear Magnetic Spectroscopy (NMR) combined with the application of methods of dissemination and multidimensional relaxometry. In this work, funded by the EC Project InsideFood, several artificial food models, based on foams and gels were studied using MRI and 2D relaxometry. Two different kinds of foams were used: a sugarless and a sugar foam. Then, a half of a syringe was filled with the sugarless foam and the other half with the sugar foam. Then, MRI and NMR experiments were performed and the sample evolution was observed along 3 days in order to quantify macrostructural changes through proton density images and microstructural ones using T1T2 maps, using an inversion CPMG sequence. On the proton density images it may be seen that after 16 hours it was possible to differentiate the macrostructural changes, as the apparition of free water due to a syneresis phenomenon. On the interface it can be seen a brighter area after 16 hours, due to the occurrence of free water. Moreover, thanks to the bidimensional relaxometry (T1-T2) it was possible to differentiate among microscopic changes. Differences between the pores size can be observed as well as the microstructure evolution after 30.5 hours, as a consequence differences are shown on free water redistribution through larger pores and capillarity phenomena between both foams.

Desarrollo y caracterización de un material celular de alta porosidad con base cementicia activada mediante agentes inorgánicos

Esta tesis ha estudiado los morteros celulares, centrándose en la experimentación con pastas de cemento aireadas (PCA) con polvo de aluminio como agente expansor. El objetivo es el desarrollo de un material cementicio con una baja conductividad térmica que sirva como aislamiento térmico. La naturaleza inorgánica del material lo hace incombustible, en contraste con las espumas poliméricas existentes en el mercado, cuya aplicación en cámaras ventiladas ha sido prohibida por normativas de construcción tanto a nivel nacional como internacional. Las posibles aplicaciones son con proyección neumática o en paneles prefabricados. Se han ensayado dos series de pastas de cemento con polvo de aluminio: - Serie WPC/CAC/CH. Mezcla de referencia con cemento blanco (WPC), cemento de aluminato cálcico (CAC) y cal aérea (CH) en proporción 5:1:4. - Serie OPC/CH. Mezcla de referencia con cemento portland con cenizas volantes (OPC) y cal aérea (CH) en proporción OPC/CH de 4:1 A las mezclas de referencia se le han añadido adiciones de metacaolín (MK) (10 y 20%) o sepiolita (SP) (1 y 2%) para observar el efecto que producen tanto en el mortero fresco como en el mortero endurecido. Se ha estudiado la reología de las pastas en estado fresco, analizando el proceso de expansión de las pastas, registrando los valores de tensión de fluencia, aire ocluido y temperatura durante la expansión. Con los valores obtenidos se ha discutido la influencia de las adiciones utilizadas en la cinética de corrosión del polvo de aluminio que genera la expansión, concluyendo que las adiciones puzolánicas (CV y MK) y la SP reducen mucho el periodo de inducción, lo que provoca poros más grandes y mayor cantidad de aire ocluido. Asimismo se ha analizado la relación entre la tensión de fluencia y el contenido de aire ocluido, deduciendo que a mayor tensión de fluencia en el momento de iniciarse la expansión, menor tamaño de poros y contenido de aire ocluido. Finalmente, se han obtenido las densidades y capacidades de retención de agua de los morteros frescos. Para caracterizar la red porosa de las pastas aireadas endurecidas, se obtuvieron tanto las densidades reales, netas, aparentes y relativas como las porosidades abiertas, cerradas y totales con ensayos hídricos. Finalmente se obtuvieron imágenes de los poros con tomografía axial computerizada para obtener las porosimetrías de las muestras. La caracterización de la red porosa ha servido para terminar de analizar lo observado en la evolución de la expansión del mortero fresco. Se ha analizado la influencia de la red porosa en la conductividad térmica, obtenida con caja caliente, comparándola con la existente en la literatura existente tanto de morteros celulares como de espumas poliméricas. Se concluye que los valores de conductividad térmica conseguida están en el mínimo posible para un material celular de base cementicia. La microestructura se ha estudiado con microscopía electrónica de barrido, difracción de rayos X y ensayos térmicos TG/ATD, observando que los productos de hidratación encontrados coinciden con los que se producen en morteros sin airear. Las imágenes SEM y los resultados de ultrasonidos han servido para analizar la presencia de microfisuras de retracción en las pastas aireadas, observando que en las muestras con adiciones de MK y SP, se reduce la presencia de microfisuras. ABSTRACT This thesis has studied cellular mortars, focusing in testing aerated cement pastes with aluminum powder as expansive agent. The purpose is the development of a cementitious material with low thermal conductivity that can be used as thermal isolation. Inorganic nature of this material makes it non-combustible, in contrast with polymeric foams in market, whose application in ventilated double skin façade systems has been banned by building standards, both domestically and internationally. Possible uses for this material are pneumatically sprayed applications and precast panels. Two series of batches with aluminum powder have been tested: - WPC/CAC/CH series. Reference paste with white portland cement (WPC), calcium aluminate cement (CAC) and lime (CH) with 5:1:4 ratio. - OPC/CH series. Reference paste with portland cement with fly ash (OPC) and lime (CH) with 4:1 ratio. Metakaolin (MK) (10 and 20%) or sepiolite (SP) (1 and 2%) additions were used in reference pastes to characterize the effect in fresh and hardened mortar. Rheology in fresh pastes was studied, expansion process of pastes was analyzed, recording yield stress, entrained air and temperature values during expansion. Recorded values were used to discuss influence of additions on reaction kinetics of aluminum powder corrosion, that produces expansion.. Conclusion is that pozzolanic additions (FA and MK) and SP greatly reduce induction period, producing bigger pores and more entrained air. Relation between yield stress and entrained air has been also analyzed, observing that the bigger yield stress at beginning of expansion, the smaller pores size and the lower entrained air values. Finally density and water retention of fresh mortars were obtained. Pore network in hardened aerated cement pastes was characterized by imbibition methods providing true, bulk and relative density, and providing also open, closed and total porosity. Finally, pore system imaging were obtained with computerized axial tomography to study porosimetry of specimens. Pore network characterization was useful to complete facts analysis observed in expansion of fresh mortars. Influence of pore network in thermal conductivity, checked in hot box, was analyzed comparing with those existing values in cellular mortar and polymeric foams researches. It was concluded that thermal conductivity values achieved are close to minimum possible in a cementitious cellular material. Microstructure was studied with Scanning Electron Microscopy, X-Ray Diffractometry and TG-DTA analysis, observing that hydration phases found, are those produced in non aerated mortar. SEM imaging and ultrasound results were useful to analyze shrinkage microcracks in aerated cement pastes, concluding that microcrack presence in specimens with MK and SP additions were reduced.

Long wave theory for experimental devices with compressed/expanded surfactant monolayers

Surfactant monolayers are of interest in a variety of phenomena, including thin film dynamics and the formation and dynamics of foams. Measurement of surface properties has received a continuous attention and requires good theoretical models to extract the relevant physico- chemical information from experimental data. A common experimental set up consists in a shallow liquid layer whose free surface is slowly com- pressed/expanded in periodic fashion by moving two slightly immersed solid barriers, which varies the free surface area and thus the surfactant concentration. The simplest theory ignores the fluid dynamics in the bulk fluid, assuming spatially uniform surfactant concentration, which requires quite small forcing frequencies and provides reversible dynamics in the compression/expansion cycles. Sometimes, it is not clear whether depar- ture from reversibility is due to non-equilibrium effects or to the ignored fluid dynamics. Here we present a long wave theory that takes the fluid dynamics and the symmetries of the problem into account. In particular, the validity of the spatially-uniform-surfactant-concentration assumption is established and a nonlinear diffusion equation is derived. This allows for calculating spatially nonuniform monolayer dynamics and uncovering the physical mechanisms involved in the surfactant behavior. Also, this analysis can be considered a good means for extracting more relevant information from each experimental run.

An eco-friendly way to fire retardant flexible polyurethane foam: layer-by-layer assembly of fully bio-based substances

The objective of the present study is to develop fully renewable and environmentally benign techniques for improving the fire safety of flexible polyurethane foams (PUFs). A multilayered coating made from cationic chitosan (CS) and anionic alginate (AL) was deposited on PUFs through layer-by-layer assembly. This coating system exhibits a slight influence on the thermal stability of PUF, but significantly improves the char formation during combustion. Cone calorimetry reveals that 10 CS-AL bilayers (only 5.7% of the foams weight) lead to a 66% and 11% reduction in peak heat release rate and total heat release, respectively, compared with those of the uncoated control. The notable decreased fire hazards of PUF are attributed to the CS-AL coatings being beneficial to form an insulating protective layer on the surface of burning materials that inhibits the oxygen and heat permeation and slows down the flammable gases in the vapor phase, and thereby improves the flame resistance. This water-based, environmentally benign natural coating will stimulate further efforts in improving fire safety for a variety of polymer substrates.

Evaluación teórico experimental de la influencia de espumas de relleno metálicas como elementos de absorción de energía en perfiles tubulares de pequeño espesor. Su aplicación a vehículos para el transporte colectivo de personas

Los accidentes con implicación de autocares en los que se producen vuelcos ponen de manifiesto la especial agresividad de los mismos, como lo confirman las estadísticas. Como medida para mejorar la seguridad de los Vehículos de Grandes Dimensiones para el Transporte de Pasajeros (V.G.D.T.P.) frente a vuelco fue aprobado por las Naciones Unidas el Reglamento Nº 66 de Ginebra. Este reglamento establece los requisitos mínimos que las estructuras de los vehículos de grandes dimensiones deben cumplir con respecto a vuelco. El reglamento 66 ha supuesto un paso adelante muy importante en relación con la seguridad de los autocares, puesto que especifica por primera vez requerimientos estructurales a este tipo de vehículos, y en general ha supuesto una mejora del vehículo . Por otro lado, a consecuencia de la obligatoriedad de instalación de cinturones de seguridad, existe una unión entre pasajeros y vehículo, pero como no se trata de una unión rígida, hay que contemplar el porcentaje de la masa de los ocupantes que influye en la absorción de energía de la estructura. Además la retención de los ocupantes con cinturones de seguridad influye en la energía a absorber por la estructura del vehículo en dos aspectos, por un lado aumenta la masa del vehículo y en el otro se incrementa la altura el centro de gravedad. Esta situación a conducido a elaborar por parte de las Naciones Unidas la revisión 01 del Reglamento 66, en el que se considera que el 50 % de la masa total de los pasajeros posee una unión rígida con la estructura del vehículo, y por lo tanto debe ser tenida en cuenta si el vehículo posee sistemas de retención. En la situación actual, con limitaciones de peso del vehículo y peso por eje, los elementos de confort, seguridad y espacio para maleteros contribuyen a aumentar el peso del vehículo. Esto unido a la dificultad de introducción de cambios radicales en la concepción actual de fabricación de este tipo de vehículos por suponer unas pérdidas importantes para los fabricantes existentes, tanto en su conocimiento del producto como en su metodología de proceso, conlleva la necesidad cada vez más agobiante de analizar y evaluar otras alternativas estructurales que sin suponer grandes revoluciones a los productos actualmente en fabricación los complementen permitiendo adaptarse a los nuevos requerimientos en seguridad. Recientes desarrollos en la relación costo-beneficio de los procesos para la producción de materiales celulares metálicos de baja densidad, tales como las espumas metálicas, los posiciona como una alternativa de especial interés para la aplicación como elementos de absorción de energía para reforzar estructuras. El relleno con espumas metálicas puede ser más eficiente en términos de optimización de peso comparado con el aumento de espesor de los perfiles estructurales, dado que la absorción de energía se produce en una fracción relativamente pequeña de los perfiles, en las denominadas rótulas plásticas. La aplicación de espumas de relleno metálicas en estructuras de vehículos se está empezando a emplear en determinadas zonas de los vehículos de turismo, siendo totalmente novedosa cualquier intento de aplicación en estructuras de autobuses y autocares. Conforme a lo expuesto, y con el objeto de resolver estos problemas, se ha elaborado el presente trabajo de tesis doctoral, cuyos objetivos son: -Desarrollar un modelo matemático, que permita simular el ensayo de vuelco, considerando la influencia de los ocupantes retenidos con cinturones de seguridad para evaluar su influencia en la absorción de energía de la estructura. -Validar el modelo matemático de vuelco de la estructura mediante ensayos de secciones representativas de la estructura del vehículo y mediante el ensayo de un vehículo completo. -Realizar un estudio de las propiedades de las espumas metálicas que permitan incorporarlas como elemento de absorción de energía en el relleno de componentes de la superestructura de autobuses y autocares. -Desarrollar un modelo matemático para evaluar el aporte del relleno de espuma metálica en la absorción de energía ante solicitaciones por flexión estática y dinámica en componentes de la superestructura de autobuses o autocares. -Realizar un programa de ensayos a flexión estáticos y dinámicos para validar el modelo matemático del aporte del relleno de espuma metálica sobre componentes de la superestructura de autobuses y autocares. . -Incorporar al modelo matemático de vuelco de la estructura, los resultados obtenidos sobre componentes con relleno de espuma metálica, para evaluar el aporte en la absorción de energía. -Validar el modelo de vuelco de la estructura del autobús o autocar con relleno de espuma metálica, mediante ensayos de secciones de carrocería. ABSTRACT Accidents involving buses in which rollovers occur reveal the special aggressiveness thereof, as the statistics prove. As a measure to improve the safety of large vehicles for the transport of passengers to rollover, Regulation 66 of Geneva was approved by the United Nations. This regulation establishes the minimum requirements that structures of large vehicles must comply with respect to rollovers. The regulation 66 has been a major step forward in relation to the safety of coaches, since it specifies structural requirements to such vehicles and has been an improvement for the vehicle. In turn, as a result of compulsory installation of safety belts, there is contact between passengers and vehicle, but as it is not a rigid connection we must contemplate the percentage of the mass of the occupants that impacts on the energy absorption of the structure. Thus, the passengers’ restraining modifies the energy to absorb by the vehicle in two different aspects: On the one hand, it increases the vehicle weight and on the other the height of the center of gravity. This circumstance has taken the United Nations to elaborate Revision 01 of Regulation 66, in which it is considered that the 50 percent of passengers’ mass has a rigid joint together with the vehicle structure and, therefore, the passengers’ mass mentioned above should be highly considered if the vehicle has seat belts. In the present situation, in which limitations in vehicle weight and weight in axles are stricter, elements of comfort, safety and space for baggage are contributing to increase the weight of the vehicle. This coupled with the difficulty of introducing radical changes in the current conception of manufacturing such vehicles pose significant losses for existing manufacturers, both in product knowledge and process methodology, entails the overwhelming need to analyze and evaluate other structural alternatives without assuming relevant modifications on the products manufactured currently allowing them to adapt to the new safety requirements. Recent developments in cost-benefit processes for the production of metallic foams of low density, such as metal foams, place them as an alternative of special interest to be used as energy absorbers to strengthen structures. The filling with metal foams can be more efficient in terms of weight optimization compared with increasing thickness of the structural beams, since the energy absorption occurs in a relatively small fraction of the beams, called plastic hinges. The application of metal filling foams in vehicle structures is beginning to be used in certain areas of passenger cars, being an innovative opportunity in structures for application in buses and coaches. According to the mentioned before, and in order to come forward with a solution, this doctoral thesis has been prepared and its objectives are: - Develop a mathematical model to simulate the rollover test, considering the influence of the occupants held with seat belts to assess their influence on energy absorption structure. - Validate the mathematical model of the structure rollover by testing representative sections of the vehicle structure and by testing a complete vehicle. - Conduct a study of the properties of metal foams as possible incorporation of energy absorbing element in the filler component of the superstructure of buses and coaches. - Elaborate a mathematical model to assess the contribution of the metal foam filling in absorbing energy for static and dynamic bending loads on the components of buses or coaches superstructure. - Conduct a static and dynamic bending test program to validate the mathematical model of contribution of metal foam filling on components of the superstructure of buses and coaches bending. - To incorporate into the mathematical model of structure rollover, the results obtained on components filled with metal foam, to evaluate the contribution to the energy absorption. - Validate the rollover model structure of the bus or coach filled with metal foam through tests of bay sections. The objectives in this thesis have been achieved successfully. The contribution calculation model with metal foam filling in the vehicle structure has revealed that the filling with metal foam is more efficient than increasing thickness of the beams, as demonstrated in the experimental validation of bay sections.

Reator anaeróbio em batelada seqüencial contendo biomassa imobilizada submetido a aumento de carga orgânica tratando água residuária sintética

Nesse estudo, procurou-se investigar a influência do aumento de carga orgânica em um ASBR operado a 30ºC, agitado mecanicamente e contendo microrganismos imobilizados em suporte inerte. Para tal, foi aplicado um carregamento orgânico volumétrico variando de 1,5 a 6,0 g DQO/L.dia, alimentando-se um reator construído em acrílico (5,4 L) com 2 L de água residuária sintética com concentrações de 500 a 2000 mg DQO/L com fontes de carboidrato/proteína/lipídio, em bateladas de 8 a 12 h. O sistema apresentou eficiências de remoção de material orgânico entre 73% e 88% para as condições estudadas. Entretanto, quando o reator foi alimentado com uma concentração de 2000 mg DQO/L em bateladas de 8 h, verificou-se o acúmulo de ácidos voláteis totais, refletindo na redução da eficiência de remoção de material orgânico para 55%, para amostras filtradas. Os perfis dinâmicos ao longo da batelada permitiram concluir que, para a condição com o mesmo carregamento orgânico, porém com concentrações afluentes e tempos de ciclo diferentes, a produção inicial de ácidos voláteis totais foi mais acentuada para o caso de alimentação com maior concentração. Para condições com concentrações afluentes iguais, o tempo a mais para o ciclo foi fundamental para obter-se efluente de melhor qualidade em termos de remoção de matéria orgânica.

Evaluation of Two Alternative Procedures for Measuring Airflow Resistance of Sound Absorbing Materials

It is well known that sound absorption and sound transmission properties of open porous materials are highly dependent on their airflow resistance values. Low values of airflow resistance indicate little resistance for air streaming through the porous material and high values are a sign that most of the pores inside the material are closed. The laboratory procedures for measuring airflow resistance have been stan- dardized by several organizations, including ISO and ASTM for both alternate flow and continuous flow. However, practical implementation of these standardized methods could be both complex and expensive. In this work, two indirect alternative measurement procedures were compared against the alternate flow standardized technique. The techniques were tested using three families of eco-friendly sound absorbent materials: recycled polyurethane foams, coconut natural fibres, and recycled polyester fibres. It is found that the values of airflow resistance measured using both alternative methods are very similar. There is also a good correlation between the values obtained through alternative and standardized methods.

Influence of drill speed and feed rate on bone damage

Implant failures and postoperative complications are often associated to the bone drilling. Estimation and control of drilling parameters are critical to prevent mechanical damage to the bone tissues. For better performance of the drilling procedures, it is essential to understand the mechanical behaviour of bones that leads to their failures and consequently to improve the cutting conditions. This paper investigates the effect of drill speed and feed-rate on mechanical damage during drilling of solid rigid foam materials, with similar mechanical properties to the human bone. Experimental tests were conducted on biomechanical blocks instrumented with strain gauges to assess the drill speed and feed-rate influence. A three-dimensional dynamic finite element model to predict the bone stresses, as a function of drilling conditions, drill geometry and bone model, was developed. These simulations incorporate the dynamic characteristics involved in the drilling process. The element removal scheme is taken into account and allows advanced simulations of tool penetration and material removal. Experimental and numerical results show that generated stresses in the material tend to increase with tool penetration. Higher drill speed leads to an increase of von-Mises stresses and strains in the solid rigid foams. However, when the feed-rate is higher, the stresses and strains are lower. The numerical normal stresses and strains are found to be in good agreement with experimental results. The models could be an accurate analysis tool to simulate the stresses distribution in the bone during the drilling process.

Performance evaluation of test dummies with flesh parts produced with substitute foaming compounds. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Side impact crashworthiness of full-size hardtop automobiles. Final report. Phase II.

National Highway Traffic Safety Administration, Washington, D.C.