Hillslope scale surface runoff, sediment, and nutrient losses associated with tramline wheelings

Research on arable sandy loam and silty clay loam soils on 4° slopes in England has shown that tramlines (i.e. the unseeded wheeling areas used to facilitate spraying operations in cereal crops) can represent the most important pathway for phosphorus and sediment loss from moderately sloping fields. Detailed monitoring over the October–March period in winters 2005–2006 and 2006–2007 included event-based sampling of surface runoff, suspended and particulate sediment, and dissolved and particulate phosphorus from hillslope segments (each ∼300–800 m2) established in a randomized block design with four replicates of each treatment at each of two sites on lighter and heavier soils. Experimental treatments assessed losses from the cropped area without tramlines, and from the uncropped tramline area, and were compared to losses from tramlines which had been disrupted once in the autumn with a shallow tine. On the lighter soil, the effects of removal or shallow incorporation of straw residues was also determined. Research on both sandy and silty clay loam soils across two winters showed that tramline wheelings represented the dominant pathway for surface runoff and transport of sediment, phosphorus and nitrogen from cereal crops on moderate slopes. Results indicated 5·5–15·8% of rainfall lost as runoff, and losses of 0·8–2·9 kg TP ha−1 and 0·3–4·8 t ha−1 sediment in tramline treatments, compared to only 0·2–1·7% rainfall lost as runoff, and losses of 0·0–0·2 kg TP ha−1 and 0·003–0·3 t ha−1 sediment from treatments without tramlines or those where tramlines had been disrupted. The novel shallow disruption of tramline wheelings using a tine once following the autumn spray operation consistently and dramatically reduced (p < 0·001) surface runoff and loads of sediment, total nitrogen and total phosphorus to levels similar to those measured in cropped areas between tramlines. Results suggest that options for managing tramline wheelings warrant further refinement and evaluation with a view to incorporating them into spatially-targeted farm-level management planning using national or catchment-based agri-environment policy instruments aimed at reducing diffuse pollution from land to surface water systems. Copyright © 2010 John Wiley & Sons, Ltd.

Structural and magnetic studies of Schiff base complexes of nickel(ii) nitrite: change in crystalline state, ligand rearrangement and a very rare μ-nitrito-1κO:2κN:3κO′ bridging mode

Four new nickel(II) complexes, [Ni2L2(NO2)2]·CH2Cl2·C2H5OH, 2H2O (1), [Ni2L2(DMF)2(m-NO2)]ClO4·DMF (2a), [Ni2L2(DMF)2(m-NO2)]ClO4 (2b) and [Ni3L¢2(m3-NO2)2(CH2Cl2)]n·1.5H2O (3) where HL = 2-[(3-amino-propylimino)-methyl]-phenol, H2L¢ = 2-({3-[(2-hydroxy-benzylidene)-amino]-propylimino}-methyl)-phenol and DMF = N,N-dimethylformamide, have been synthesized starting with the precursor complex [NiL2]·2H2O, nickel(II) perchlorate and sodium nitrite and characterized structurally and magnetically. The structural analyses reveal that in all the complexes, NiII ions possess a distorted octahedral geometry. Complex 1 is a dinuclear di-m2-phenoxo bridged species in which nitrite ion acts as chelating co-ligand. Complexes 2a and 2b also consist of dinuclear entities, but in these two compounds a cis-(m-nitrito-1kO:2kN) bridge is present in addition to the di-m2-phenoxo bridge. The molecular structures of 2a and 2b are equivalent; they differ only in that 2a contains an additional solvated DMF molecule. Complex 3 is formed by ligand rearrangement and is a one-dimensional polymer in which double phenoxo as well as m-nitrito-1kO:2kN bridged trinuclear units are linked through a very rare m3-nitrito-1kO:2kN:3kO¢ bridge. Analysis of variable-temperature magnetic susceptibility data indicates that there is a global weak antiferromagnetic interaction between the nickel(II) ions in four complexes, with exchange parameters J of -5.26, -11.45, -10.66 and -5.99 cm-1 for 1, 2a, 2b and 3, respectively

Estimation of optimal gravity wave parameters for climate models using data assimilation

There is a current need to constrain the parameters of gravity wave drag (GWD) schemes in climate models using observational information instead of tuning them subjectively. In this work, an inverse technique is developed using data assimilation principles to estimate gravity wave parameters. Because mostGWDschemes assume instantaneous vertical propagation of gravity waves within a column, observations in a single column can be used to formulate a one-dimensional assimilation problem to estimate the unknown parameters. We define a cost function that measures the differences between the unresolved drag inferred from observations (referred to here as the ‘observed’ GWD) and the GWD calculated with a parametrisation scheme. The geometry of the cost function presents some difficulties, including multiple minima and ill-conditioning because of the non-independence of the gravity wave parameters. To overcome these difficulties we propose a genetic algorithm to minimize the cost function, which provides a robust parameter estimation over a broad range of prescribed ‘true’ parameters. When real experiments using an independent estimate of the ‘observed’ GWD are performed, physically unrealistic values of the parameters can result due to the non-independence of the parameters. However, by constraining one of the parameters to lie within a physically realistic range, this degeneracy is broken and the other parameters are also found to lie within physically realistic ranges. This argues for the essential physical self-consistency of the gravity wave scheme. A much better fit to the observed GWD at high latitudes is obtained when the parameters are allowed to vary with latitude. However, a close fit can be obtained either in the upper or the lower part of the profiles, but not in both at the same time. This result is a consequence of assuming an isotropic launch spectrum. The changes of sign in theGWDfound in the tropical lower stratosphere, which are associated with part of the quasi-biennial oscillation forcing, cannot be captured by the parametrisation with optimal parameters.

Single-carrier frequency domain equalisation for hammerstein communication systems using complex-valued neural networks

Single-carrier (SC) block transmission with frequency-domain equalisation (FDE) offers a viable transmission technology for combating the adverse effects of long dispersive channels encountered in high-rate broadband wireless communication systems. However, for high bandwidthefficiency and high power-efficiency systems, the channel can generally be modelled by the Hammerstein system that includes the nonlinear distortion effects of the high power amplifier (HPA) at transmitter. For such nonlinear Hammerstein channels, the standard SC-FDE scheme no longer works. This paper advocates a complex-valued (CV) B-spline neural network based nonlinear SC-FDE scheme for Hammerstein channels. Specifically, We model the nonlinear HPA, which represents the CV static nonlinearity of the Hammerstein channel, by a CV B-spline neural network, and we develop two efficient alternating least squares schemes for estimating the parameters of the Hammerstein channel, including both the channel impulse response coefficients and the parameters of the CV B-spline model. We also use another CV B-spline neural network to model the inversion of the nonlinear HPA, and the parameters of this inverting B-spline model can easily be estimated using the standard least squares algorithm based on the pseudo training data obtained as a natural byproduct of the Hammerstein channel identification. Equalisation of the SC Hammerstein channel can then be accomplished by the usual one-tap linear equalisation in frequency domain as well as the inverse B-spline neural network model obtained in time domain. Extensive simulation results are included to demonstrate the effectiveness of our nonlinear SC-FDE scheme for Hammerstein channels.

B-spline neural network based single-carrier frequency domain equalisation for Hammerstein channels

A practical single-carrier (SC) block transmission with frequency domain equalisation (FDE) system can generally be modelled by the Hammerstein system that includes the nonlinear distortion effects of the high power amplifier (HPA) at transmitter. For such Hammerstein channels, the standard SC-FDE scheme no longer works. We propose a novel Bspline neural network based nonlinear SC-FDE scheme for Hammerstein channels. In particular, we model the nonlinear HPA, which represents the complex-valued static nonlinearity of the Hammerstein channel, by two real-valued B-spline neural networks, one for modelling the nonlinear amplitude response of the HPA and the other for the nonlinear phase response of the HPA. We then develop an efficient alternating least squares algorithm for estimating the parameters of the Hammerstein channel, including the channel impulse response coefficients and the parameters of the two B-spline models. Moreover, we also use another real-valued B-spline neural network to model the inversion of the HPA’s nonlinear amplitude response, and the parameters of this inverting B-spline model can be estimated using the standard least squares algorithm based on the pseudo training data obtained as a byproduct of the Hammerstein channel identification. Equalisation of the SC Hammerstein channel can then be accomplished by the usual one-tap linear equalisation in frequency domain as well as the inverse Bspline neural network model obtained in time domain. The effectiveness of our nonlinear SC-FDE scheme for Hammerstein channels is demonstrated in a simulation study.

Infrared and millimetre-wave scintillometry in the suburban environment – Part 1: Structure parameters

Scintillometry, a form of ground-based remote sensing, provides the capability to estimate surface heat fluxes over scales of a few hundred metres to kilometres. Measurements are spatial averages, making this technique particularly valuable over areas with moderate heterogeneity such as mixed agricultural or urban environments. In this study, we present the structure parameters of temperature and humidity, which can be related to the sensible and latent heat fluxes through similarity theory, for a suburban area in the UK. The fluxes are provided in the second paper of this two-part series. A millimetre-wave scintillometer was combined with an infrared scintillometer along a 5.5 km path over northern Swindon. The pairing of these two wavelengths offers sensitivity to both temperature and humidity fluctuations, and the correlation between wavelengths is also used to retrieve the path-averaged temperature–humidity correlation. Comparison is made with structure parameters calculated from an eddy covariance station located close to the centre of the scintillometer path. The performance of the measurement techniques under different conditions is discussed. Similar behaviour is seen between the two data sets at sub-daily timescales. For the two summer-to-winter periods presented here, similar evolution is displayed across the seasons. A higher vegetation fraction within the scintillometer source area is consistent with the lower Bowen ratio observed (midday Bowen ratio < 1) compared with more built-up areas around the eddy covariance station. The energy partitioning is further explored in the companion paper.

Optimization of a sponge cake formulation with inulin as fat replacer: structure, physicochemical, and sensory properties

The effects of several fat replacement levels (0%, 35%, 50%, 70%, and 100%) by inulin in sponge cake microstructure and physicochemical properties were studied. Oil substitution for inulin decreased significantly (P < 0.05) batter viscosity, giving heterogeneous bubbles size distributions as it was observed by light microscopy. Using confocal laser scanning microscopy the fat was observed to be located at the bubbles’ interface, enabling an optimum crumb cake structure development during baking. Cryo-SEM micrographs of cake crumbs showed a continuous matrix with embedded starch granules and coated with oil; when fat replacement levels increased, starch granules appeared as detached structures. Cakes with fat replacement up to 70% had a high crumb air cell values; they were softer and rated as acceptable by an untrained sensory panel (n = 51). So, the reformulation of a standard sponge cake recipe to obtain a new product with additional health benefits and accepted by consumers is achieved.

Mathematical relationships between scoring parameters in capped tendering

Mathematical relationships between Scoring Parameters can be used in Economic Scoring Formulas (ESF) in tendering to distribute the score among bidders in the economic part of a proposal. Each contracting authority must set an ESF when publishing tender specifications and the strategy of each bidder will differ depending on the ESF selected and the weight of the overall proposal scoring. This paper introduces the various mathematical relationships and density distributions that describe and inter-relate not only the main Scoring Parameters but the main Forecasting Parameters in any capped tender (those whose price is upper-limited). Forecasting Parameters, as variables that can be known in advance before the deadline of a tender is reached, together with Scoring Parameters constitute the basis of a future Bid Tender Forecasting Model.

An analysis of teaching methods for children who are deaf with multiple disabilities

This study analyzes the placement, services, and teaching methods of students who are deaf with additional disabilities. Through this analysis, these students are compared to students with multiple disabilities, not including deafness.

Analysis of experimental interlocking blocks of concrete with addition of residues of process the tires retreading production

Analysis of experimental interlocking blocks of concrete with addition of residues of process the tires retreading production. With the population growth in recent years, industry in general has adjusted itself to resulting demand. the industry of tire retreading generates residues that have been discarded without any control. this adds to environmental pollution and promotes the proliferation of vectors harmful to health, aiming to find an application for this type of residues, this study presents experimental results to interlocking concrete block pavements, with addition of residues tires, interlocking blocks were built up and we determined, through laboratory tests, the need to set the mark that provide greater return regarding analyzed characteristics, there are four types of dosage of concrete with residues tires. We accomplished tests of compression strength, water absorption and resistance to impact. Through the preliminary results, we verified that are satisfactory, confirming the possibility of applying this type of interlocking block in environments with low demand, which would bring the economy of natural sources of aggregates, beyond ecological benefits through the reuse of residues from retreading of tires.

Effects of low-level laser therapy and eccentric exercises in the treatment of recreational athletes with chronic achilles tendinopathy

Background: Eccentric exercises (EEs) are recommended for the treatment of Achilles tendinopathy, but the clinical effect from EE has a slow onset. Hypothesis: The addition of low-level laser therapy (LLLT) to EE may cause more rapid clinical improvement. Study Design: Randomized controlled trial; Level of evidence, 1. Methods: A total of 52 recreational athletes with chronic Achilles tendinopathy symptoms were randomized to groups receiving either EE + LLLT or EE + placebo LLLT over 8 weeks in a blinded manner. Low-level laser therapy (lambda = 820 nm) was administered in 12 sessions by irradiating 6 points along the Achilles tendon with a power density of 60 mW/cm(2) and a total dose of 5.4 J per session. Results: The results of the intention-to-treat analysis for the primary outcome, pain intensity during physical activity on the 100-mm visual analog scale, were significantly lower in the LLLT group than in the placebo LLLT group, with 53.6 mm versus 71.5 mm (P = .0003) at 4 weeks, 37.3 mm versus 62.8 mm (P = .0002) at 8 weeks, and 33.0 mm versus 53.0 mm (P =.007) at 12 weeks after randomization. Secondary outcomes of morning stiffness, active dorsiflexion, palpation tenderness, and crepitation showed the same pattern in favor of the LLLT group. Conclusion: Low-level laser therapy, with the parameters used in this study, accelerates clinical recovery from chronic Achilles tendinopathy when added to an EE regimen. For the LLLT group, the results at 4 weeks were similar to the placebo LLLT group results after 12 weeks.

Permanence of stability for a class of system of differential equations with two delays

The paper studies a class of a system of linear retarded differential difference equations with several parameters. It presents some sufficient conditions under which no stability changes for an equilibrium point occurs. Application of these results is given. (c) 2007 Elsevier Ltd. All rights reserved.

Plastificação de um solo cimentado curado sob tensão

A fim de avaliar a contribuição das ligações cimentantes no comportamento tensão-deformação dos solos cimentados, bem como quantificar a variação das tensões de início de plastificação e incremento de tensão de plastificação em função do índice de vazios de cura, foram realizados dezoito ensaios de compressão isotrópica em amostras artificialmente cimentadas curadas com diferentes tensões confinantes, índices de vazios e teores de cimento. As amostras foram inicialmente adensadas a várias tensões confinantes ao longo da linha de compressão normal do solo sem cimentação, simulando a formação de elementos de solos em diferentes profundidades de um depósito sedimentar cimentado. Após o adensamento, as amostras eram curadas para posterior aplicação de incrementos de tensão isotrópica. Complementarmente, dezenove ensaios triaxiais drenados foram realizados em amostras artificialmente cimentadas curadas sob diferentes tensões confinantes e índices de vazios de forma a analisar as modificações dos parâmetros de resistência, deformabilidade e plastificação em função do índice de vazios e tensão de cura. Por final, um novo modelo matemático foi proposto para simular os ensaios isotrópicos das amostras curadas com diferentes índices de vazios e teores de cura, descrevendo o comportamento teórico dos elementos de solo situados nas diferentes profundidades do depósito fictício de solo cimentado. A capacidade do modelo de simular os resultados dos ensaios isotrópicos para uma gama ampla de índice de vazios de cura e teores de cimento também foi apresentada. Comentários acerca das respostas obtidas com simulações de amostras curadas a altos e baixos índices de vazios, e solicitadas a elevadas tensões isotrópicas, também são apresentadas juntamente com uma análise dos três parâmetros adicionais requeridos pelo modelo em relação ao modelo Cam Clay: um parâmetro de medida de nível de cimentação, um parâmetro definidor do tipo de comportamento da estrutura cimentante (rígido, rígido-plástico, linear, etc.), e um parâmetro que relaciona a magnitude das tensões da estrutura cimentante com o nível de cimentação da amostra.

Custos e rentabilidade da produção de juvenis de tilápia-do-nilo em tanques-rede utilizando-se diferentes densidades de estocagem

Neste trabalho foi realizada a análise econômica da produção de juvenis de tilápia-do-nilo em tanques-rede utilizando-se diferentes densidades de estocagem. O experimento foi desenvolvido em área aquícola, em delineamento de blocos casualizados, com quatro densidades de estocagem (100, 200, 300 e 400 peixes m-3), avaliadas com seis repetições, em dois períodos de criação: de março a abril de 2005 (52 dias - peso inicial de 43,08 ± 2,98 g e peso final de 262,14 ± 47,86 g) e de março a abril de 2006 (58 dias - peso inicial de 43,16 ± 5,34 g e peso final 314,24 ± 73,30 g). Foram avaliadas as seguintes variáveis econômicas: custo da ração mais custo do juvenil dividido pela biomassa, em R$ kg-1; porcentagem do custo da ração por quilo de peixe produzido sobre o preço de venda; porcentagem do custo do juvenil por quilo de peixe produzido sobre o preço de venda e; porcentagem dos custos da ração mais do juvenil por quilo de peixe produzido sobre o preço de venda. da menor densidade de estocagem (100) para a maior (400), ocorreu diminuição no ganho de peso diário e elevação do índice de conversão alimentar aparente, mas essa redução não comprometeu a taxa de sobrevivência. Entretanto, o ganho de biomassa aumentou com o adensamento de peixes. As maiores receitas líquidas foram obtidas nas densidades de estocagem de 100 e 200 peixes m-3. Os preços não remuneraram os custos operacionais (efetivo e total) em maiores densidades (300 e 400 peixes m-3). Os melhores resultados para a produção de juvenis de tilápia-do-nilo foram obtidos com densidades de até 200 peixes m-3.

Effects of plant density and proportion on the interaction between wheat with alexandergrass plants

A determinação das relações competitivas entre espécies de plantas requer delineamentos experimentais e métodos de análise apropriados. A hipótese da pesquisa foi que duas espécies crescendo em convivência têm comportamento de crescimento e desenvolvimento distintos em função da sua competitividade relativa. O objetivo desta pesquisa foi quantificar a competitividade relativa da cultura do trigo com o capim-marmelada através da medida dos efeitos da densidade e da proporção de plantas, usando experimentos em série substitutiva. Monoculturas foram cultivadas em densidades de 1, 3, 5, 10 e 15 plantas por caixa e analisadas por regressão dos dados de massa seca, em 2006. Experimento em mistura foi cultivado nas proporções trigo:capim-marmelada de 0:6, 1:5, 2:4, 3:3, 4:2, 5:1 e 6:0 plantas por caixa e analisado através de interpretação gráfica de características de crescimento e produção, em 2007. Ambos os experimentos foram realizados em delineamento completamente casualizado com quatro repetições. Capim-marmelada foi mais sensível que trigo à competição intraespecífica. Capim-marmelada foi levemente mais competitivo que trigo. Número e massa de espigas e número de afilhos foram as características do trigo mais afetadas pela interferência do capim-marmelada.