Structural refinement, optical and microwave dielectric properties of BaZrO3

In this work, barium zirconate (BaZrO3) ceramics synthesized by solid state reaction method and sintered at 1670 degrees C for 4 h were characterized by X-ray diffraction (XRD), Rietveld refinement, and Fourier transform infrared (FT-IR) spectroscopy. XRD patterns, Rietveld refinement data and FT-IR spectra which confirmed that BaZrO3 ceramics have a perovskite-type cubic structure. Optical properties were investigated by ultraviolet-visible (UV-vis) absorption and photoluminescence (PL) measurements. UV-vis absorption spectra suggested an indirect allowed transition with the existence of intermediary energy levels within the band gap. Intense visible green PL emission was observed in BaZrO3 ceramics upon excitation with a 350 nm wavelength. This behavior is due to a majority of deep defects within the band gap caused by symmetry breaking in octahedral [ZrO6] clusters in the lattice. The microwave dielectric constant and quality factor were measured using the method proposed by Hakki-Coleman. The dielectric resonator antenna (DRA) was investigated experimentally and numerically using a monopole antenna through an infinite ground plane and Ansoft's high frequency structure simulator software, respectively. The required resonance frequency and bandwidth of DRA were investigated by adjusting the dimension of the same material. (C) 2011 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Synthesis Methodology Applied to a Tunable Patch Filter With Independent Frequency and Bandwidth Control

A new methodology for the synthesis of tunable patch filters is presented. The methodology helps the designer to perform a theoretical analysis of the filter through a coupling matrix that includes the effect of the tuning elements used to tune the filter. This general methodology accounts for any tuning parameter desired and was applied to the design of a tunable dual-mode patch filter with independent control of center frequency and bandwidth (BW). The bandpass filter uses a single triangular resonator with two etched slots that split the fundamental degenerate modes and form the filter passband. Varactor diodes assembled across the slots are used to vary the frequency of each degenerate fundamental mode independently, which is feasible due to the nature of the coupling scheme of the filter. The varactor diode model used in simulations, their assembling, the dc bias configuration, and measured results are presented. The theory results are compared to the simulations and to measurements showing a very good agreement and validating the proposed methodology. The fabricated filter presents an elliptic response with 20% of center frequency tuning range around 3.2 GHz and a fractional BW variation from 4% to 12% with low insertion loss and high power handling with a 1-dB compression point higher than +14.5 dB.

Parametric study of retangular patch antenna using denim textile material

—This paper presents a textile patch antenna designed for WBAN applications at 2.45 GHz ISM band. The antenna uses denim as substrate and conductive fabric for the ground plane and radiator layers. The main purpose of this paper is to analyze the influence of typical deviation of denim properties and patch radiator dimensions on the performance of the antenna. The parameters considered in the analysis are the relative permittivity and thickness of denim and the width and length of the rectangular patch radiator. The dependence of the central operation frequency of the antenna on those parameters was studied using the antenna reflection coefficient obtained from EM simulations. Rules of thumb for one-shot design were derived and applied to design a rectangular patch antenna. An antenna prototype was fabricated and measured, demonstrating a 10 dB impedance band of 4.8 % centered at 2.45 GHz, in good agreement with simulated results

A complete CMOS UWB timed-array transmitter with a 3D Vivaldi antenna array for electronic high-resolution beam spatial scanning

We present a new Ultra Wide Band (UWB) Timed- Array Transmitter System with Beamforming capability for high-resolution remote acquisition of vital signals. The system consists of four identical channels, where each is formed of a serial topology with three modules: programmable delay circuit (PDC or τ), a novel UWB 5th Gaussian Derivative order pulse generator circuit (PG), and a planar Vivaldi antenna. The circuit was designed using 0.18μm CMOS standard process and the planar antenna array was designed with filmconductor on Rogers RO3206 substrate. Spice simulations results showed the pulse generation with 104 mVpp amplitude and 500 ps width. The power consumption is 543 μW, and energy consumption 0.27 pJ per pulse using a 2V power supply at a pulse repetition rate (PRR) of 100 MHz. Electromagnetic simulations results, using CST Microwave (MW) Studio 2011, showed the main lobe radiation with a gain maximum of 13.2 dB, 35.5º x 36.7º angular width, and a beam steering between 17º and -11º for azimuthal (θ) angles and 17º and -18º for elevation (φ) angles at the center frequency of 6 GHz

Fiber-Optic Technologies for Wireline and Wireless In-building Networks

This doctoral dissertation aims to establish fiber-optic technologies overcoming the limiting issues of data communications in indoor environments. Specific applications are broadband mobile distribution in different in-building scenarios and high-speed digital transmission over short-range wired optical systems. Two key enabling technologies are considered: Radio over Fiber (RoF) techniques over standard silica fibers for distributed antenna systems (DAS) and plastic optical fibers (POFs) for short-range communications. Hence, the objectives and achievements of this thesis are related to the application of RoF and POF technologies in different in-building scenarios. On one hand, a theoretical and experimental analysis combined with demonstration activities has been performed on cost-effective RoF systems. An extensive modeling on modal noise impact both on linear and non-linear characteristics of RoF link over silica multimode fiber has been performed to achieve link design rules for an optimum choice of the transmitter, receiver and launching technique. A successful transmission of Long Term Evolution (LTE) mobile signals on the resulting optimized RoF system over silica multimode fiber employing a Fabry-Perot LD, central launch technique and a photodiode with a built-in ball lens was demonstrated up to 525m with performances well compliant with standard requirements. On the other hand, digital signal processing techniques to overcome the bandwidth limitation of POF have been investigated. An uncoded net bit-rate of 5.15Gbit/s was obtained on a 50m long POF link employing an eye-safe transmitter, a silicon photodiode, and DMT modulation with bit and power loading algorithm. With the insertion of 3x2N quadrature amplitude modulation constellation formats, an uncoded net-bit-rate of 5.4Gbit/s was obtained on a 50 m long POF link employing an eye-safe transmitter and a silicon avalanche photodiode. Moreover, simultaneous transmission of baseband 2Gbit/s with DMT and 200Mbit/s with an ultra-wideband radio signal has been validated over a 50m long POF link.

Sea level measurement using single GNSS antenna SNR signals

This thesis presents a possible method to calculate sea level variation using geodetic-quality Global Navigate Satellite System (GNSS) receivers. Three antennas are used: two small antennas and a choke ring one, analyzing only Global Positioning System signals. The main goal of the thesis is to test a modified configuration for antenna set up. In particular, measurements obtained tilting one antenna to face the horizon are compared to measurements obtained from antennas looking upward. The location of the experiment is a coastal environment nearby the Onsala Space Observatory in Sweden. Sea level variations are obtained using periodogram analysis of the SNR signal and compared to synthetic gauge generated from two independent tide gauges. The choke ring antenna provides poor result, with an RMS around 6 cm and a correlation coefficients of 0.89. The smaller antennas provide correlation coefficients around 0.93. The antenna pointing upward present an RMS of 4.3 cm and the one pointing the horizon an RMS of 6.7 cm. Notable variation in the statistical parameters is found when modifying the length of the interval analyzed. In particular, doubts are risen on the reliability of certain scattered data. No relation is found between the accuracy of the method and weather conditions. Possible methods to enhance the available data are investigated, and correlation coefficient above 0.97 can be obtained with small antennas when sacrificing data points. Hence, the results provide evidence of the suitability of SNR signal analysis for sea level variation in coastal environment even in the case of adverse weather conditions. In particular, tilted configurations provides comparable result with upward looking geodetic antennas. A SNR signal simulator is also tested to investigate its performance and usability. Various configuration are analyzed in combination with the periodogram procedure used to calculate the height of reflectors. Consistency between the data calculated and those received is found, and the overall accuracy of the height calculation program is found to be around 5 mm for input height below 5 m. The procedure is thus found to be suitable to analyze the data provided by the GNSS antennas at Onsala.

Statistical mapping of real environments with uwb radars

In this master thesis I evaluated the performance of a Ultra-Wide Bandwidth (UWB) radar system for indoor environments mapping. In particular, I used a statistical Bayesian approach which is able to combine all the measurements collected by the radar, including system non-idealities such as the error on the estimated antenna pointing direction or on the estimated radar position. First I verified through simulations that the system was able to provide a sufficiently accurate reconstruction of the surrounding environment despite the limitations imposed by the UWB technology. In fact, the emission of UWB pulses is limited in terms of transmitted power by international regulations. Motivated by the promising results obtained through simulations, I successively carried out a measurement campaign in a real indoor environment using a UWB commercial device. The obtained results showed that the UWB radar system is capable of providing an accurate reconstruction of indoor environments also adopting not directional antennas.

Approccio teorico e numerico per la selezione di topologie d'antenna miniaturizzate su substrati magneto-dielettrici

Lo sviluppo di soluzioni sempre più pervasive, nell’ambito delle telecomunicazioni, ha determinato una necessità crescente di avere sistemi wireless con dimensioni estremamente ridotte. Tale obiettivo deve essere raggiunto evitando di incorrere nelle problematiche in termini di prestazioni di radiazione che si presentano utilizzando antenne dalle dimensioni molto ridotte rispetto la lunghezza d'onda. Tali inefficienze finiscono poi per ripercuotersi sulle funzionalità, ma sopratutto sul consumo energetico e quindi sulla sua autonomia. Nell’ambito di questa tesi, ci si è focalizzati sui materiali e in particolare su come possono essere selezionati in base alle caratteristiche delle varie topologie di antenne, con lo scopo di massimizzare le caratteristiche prestazionali dell'elemento radiante. Sarà inoltre presentata una definizione innovativa e dedicata ai materiali magneto-dielettrici del volume di campo vicino. Si concluderà infine che, nel caso di antenne rappresentate da sorgenti equivalenti magnetiche è conveniente usare materiali magnetici, mentre con sorgenti equivalenti elettriche il solo dielettrico risulta più indicato.

RFID tag localization with virtual multi-antenna systems

In questa tesi si sono valutate le prestazioni di un sistema di localizzazione multi-antenna di tag radio frequency identification (RFID) passivi in ambiente indoor. Il sistema, composto da un reader in movimento che percorre una traiettoria nota, ha come obiettivo localizzare il tag attraverso misure di fase; più precisamente la differenza di fase tra il segnale di interrogazione, emesso dal reader, e il segnale ricevuto riflesso dal tag che è correlato alla distanza tra di essi. Dopo avere eseguito una ricerca sullo stato dell’arte di queste tecniche e aver derivato il criterio maximum likelihood (ML) del sistema si è proceduto a valutarne le prestazioni e come eventuali fattori agissero sul risultato di localizzazione attraverso simulazioni Matlab. Come ultimo passo si è proceduto a effettuare una campagna di misure, testando il sistema in un ambiente reale. Si sono confrontati i risultati di localizzazione di tutti gli algoritmi proposti quando il reader si muove su una traiettoria rettilinea e su una traiettoria angolare, cercando di capire come migliorare i risultati.

Localizzazione e tracking tramite filtri statistici in sistemi multi antenna

Uno dei temi più recenti nel campo delle telecomunicazioni è l'IoT. Tale termine viene utilizzato per rappresentare uno scenario nel quale non solo le persone, con i propri dispositivi personali, ma anche gli oggetti che le circondano saranno connessi alla rete con lo scopo di scambiarsi informazioni di diversa natura. Il numero sempre più crescente di dispositivi connessi in rete, porterà ad una richiesta maggiore in termini di capacità di canale e velocità di trasmissione. La risposta tecnologica a tali esigenze sarà data dall’avvento del 5G, le cui tecnologie chiave saranno: massive MIMO, small cells e l'utilizzo di onde millimetriche. Nel corso del tempo la crescita delle vendite di smartphone e di dispositivi mobili in grado di sfruttare la localizzazione per ottenere servizi, ha fatto sì che la ricerca in questo campo aumentasse esponenzialmente. L'informazione sulla posizione viene utilizzata infatti in differenti ambiti, si passa dalla tradizionale navigazione verso la meta desiderata al geomarketing, dai servizi legati alle chiamate di emergenza a quelli di logistica indoor per industrie. Data quindi l'importanza del processo di positioning, l'obiettivo di questa tesi è quello di ottenere la stima sulla posizione e sulla traiettoria percorsa da un utente che si muove in un ambiente indoor, sfruttando l'infrastruttura dedicata alla comunicazione che verrà a crearsi con l'avvento del 5G, permettendo quindi un abbattimento dei costi. Per fare ciò è stato implementato un algoritmo basato sui filtri EKF, nel quale il sistema analizzato presenta in ricezione un array di antenne, mentre in trasmissione è stato effettuato un confronto tra due casi: singola antenna ed array. Lo studio di entrambe le situazioni permette di evidenziare, quindi, i vantaggi ottenuti dall’utilizzo di sistemi multi antenna. Inoltre sono stati analizzati altri elementi chiave che determinano la precisione, quali geometria del sistema, posizionamento del ricevitore e frequenza operativa.