Paste Residence Time in a Spouted Bed Dryer. IV: Effect of the Inert Particle Size Distribution

The residence time distribution and mean residence time of a 10% sodium bicarbonate solution that is dried in a conventional spouted bed with inert bodies were measured with the stimulus-response method. Methylene blue was used as a chemical tracer, and the effects of the paste feed mode, size distribution of the inert bodies, and mean particle size on the residence times and dried powder properties were investigated. The results showed that the residence time distributions could be best reproduced with the perfect mixing cell model or N = 1 for the continuous stirred tank reactor in a series model. The mean residence times ranged from 6.04 to 12.90 min and were significantly affected by the factors studied. Analysis of variance on the experimental data showed that mean residence times were affected by the mean diameter of the inert bodies at a significance level of 1% and by the size distribution at a level of 5%. Moreover, altering the paste feed from dripping to pneumatic atomization affected mean residence time at a 5% significance level. The dried powder characteristics proved to be adequate for further industrial manipulation, as demonstrated by the low moisture content, narrow range of particle size, and good flow properties. The results of this research are significant in the study of the drying of heat-sensitive materials because it shows that by simultaneously changing the size distribution and average size of the inert bodies, the mean residence times of a paste can be reduced by half, thus decreasing losses due to degradation.

Stability Testing of Spray- and Spouted Bed-Dried Extracts of Passiflora alata

The aim of this research was to perform a stability testing of spray- and spouted bed-dried extracts of Passiflora alata Dryander (Passion flower) under stress storage conditions. Spouted bed- and spray-dried extracts were characterized by determination of the average particle diameter (dP), apparent moisture content (XP), total flavonoid content (TF), and vitexin content. Smaller and more irregular particles were generated by the spouted bed system due to a higher attrition rate (surface erosion) inside the dryer. The SB dryer resulted in an end product with higher concentration of flavonoids (approximate to 10%) and lower moisture content (1.6%, dry basis) than the spray dryer, even with both dryers working at similar inlet drying air temperature and ratio between the extract feed flow rate to drying air flow rate (Ws/Wg). Samples of the spouted bed- and spray-dried extracts were stored at two different temperatures (34 and 45 degrees C) and two different relative humidities (52 and 63% RH for 34 degrees C; 52 and 60% RH for 45 degrees C) in order to perform the stability testing. The dried extracts were stored for 28 days and were analyzed every 4 days. The flavonoid vitexin served as the marker compound, which was assayed during the storage period. Results revealed shelf lives ranging from 9 to 184 days, depending on the drying process and storage conditions.

Rheological behavior, zeta potential, and accelerated stability tests of Buriti oil (Mauritia flexuosa) emulsions containing lyotropic liquid crystals

Background: It is well known that the Amazon region presents a huge biodiversity; therefore, countless natural resources are being employed in the production of phytocosmetics and phytomedicines. Objective: The purpose of this work was to obtain emulsions produced with Buriti oil and nonionic surfactants. Methods: Two surfactant systems were employed (Steareth-2 associated to Ceteareth-5 and to Ceteareth-20) to produce the emulsions using phase diagram method. Emulsions were obtained by echo-planar imaging method at 75 degrees C. Rheological behavior and zeta potential were evaluated, and accelerated stability tests were performed. Results: All emulsions analyzed presented pseudoplastic behavior. Zeta potential values were obtained between -14.2 and -53.3 mV. The formulations did not show changes in either physical stability, pH, or rheological behavior after accelerated stability tests. Significant differences were observed only after temperature cycling test. Conclusion: Based on these results, the emulsions obtained could be considered as promising delivery systems.

Adsorption characteristics of carbonized bark for phenol and pentachlorophenol

The potential of using carbonized slash pine bark as a substitute for activated carbon was examined in this study. The bark was carbonized by slow heating in nitrogen for 6.5 h to 672 degrees C. The BET-N-2 surface area, average micropore and mesopore diameter, and micropore volume were 332 m(2) g(-1) 21.7 Angstrom, and 0.125 cm(3) g(-1), respectively. The adsorption capacities for phenol and pentachlorophenol (PCP) at pH 2 and pH 8 were evaluated. The Langmuir equation provided a slightly better fit than the Freundlich equation to two sets of phenol data. The calculated Freundlich constants, K = 0.41 - 0.58 mmol/g/(mmol dm(-3))(1/n) and 1/n = 0.30 - 0.41, were lower and higher, respectively, than literature values for activated carbons. The adsorption capacity of the carbonized bark was much lower for PCP than for phenol. The protonated and anionic PCP isotherms were Type II or III, respectively, in the Brunauer classification. The BET equation provided the best fit to protonated PCP isotherm data. The anionic PCP data were fitted to both the BET model and an equation used in the literature to represent phosphate adsorption on activated carbons. Nonlinear regression of the data for both phenol and PCP adsorption with the Freundlich, Langmuir and BET equations generally gave more accurate parameters, compared with the use of linearized equations to obtain the parameters. (C) 1998 SCI.

Efficacy of zeta-cypermethrin as pour-on or spray formulations for the control of buffalo fly (Haematobia irritans exigua) in cattle

Objective To determine the efficacy of zeta-cypermethrin in controlling buffalo fly (Haematobia irritans exigua). Design Five field trials in northern and central Queensland. Procedure Zeta-cypermethrin pour-on at 2.5 mg/kg, spray at 62.5 ppm, deltamethrin pour-on and pour-on vehicle were applied to groups of 20 cattle. Buffalo fly counts were conducted three times before treatment and 3, 7, 14, 21, 28 and 35 days after treatment. Results In central Queensland where synthetic pyrethroid resistance in buffalo fly populations was rare, 2.5 mg/kg of zeta-cypermethrin pour-on gave good control of buffalo fly for 4 weeks and was better than a deltamethrin product. A zeta-cypermethrin spray used at 62.5 ppm gave 14 days control. In far-north Queensland where resistance to synthetic pyrethroids and heavy rain was common, the maximum period of efficacy of zeta-cypermethrin pour-on was reduced to 2 weeks. Conclusion In areas where there is low resistance to synthetic pyrethroids among buffalo flies, zeta-cypermethrin pour-on can be expected to give good control for 4 weeks.

Thermal diffusion in molecular dynamics simulations of thin film diamond deposition

Molecular dynamics simulations of carbon atom depositions are used to investigate energy diffusion from the impact zone. A modified Stillinger-Weber potential models the carbon interactions for both sp2 and sp3 bonding. Simulations were performed on 50 eV carbon atom depositions onto the (111) surface of a 3.8 x 3.4 x 1.0 nm diamond slab containing 2816 atoms in 11 layers of 256 atoms each. The bottom layer was thermostated to 300 K. At every 100th simulation time step (27 fs), the average local kinetic energy, and hence local temperature, is calculated. To do this the substrate is divided into a set of 15 concentric hemispherical zones, each of thickness one atomic diameter (0.14 nm) and centered on the impact point. A 50-eV incident atom heats the local impact zone above 10 000 K. After the initial large transient (200 fs) the impact zone has cooled below 3000 K, then near 1000 K by 1 ps. Thereafter the temperature profile decays approximately as described by diffusion theory, perturbed by atomic scale fluctuations. A continuum model of classical energy transfer is provided by the traditional thermal diffusion equation. The results show that continuum diffusion theory describes well energy diffusion in low energy atomic deposition processes, at distance and time scales larger than 1.5 nm and 1-2 ps, beyond which the energy decays essentially exponentially. (C) 1998 Published by Elsevier Science S.A. All rights reserved.

Therapeutic efficacy of zeta-cypermethrin pour-on for the treatment of biting and sucking lice in cattle under field conditions

Objective To assess the efficacy of zeta-cypermethrin pour-on to control cattle lice. Design Five field trials in south-eastern Australia. Procedure Zeta-cypermethrin pour-on, deltamethrin pour-on and pour-on vehicle were applied to groups of 10 cattle. Lice were counted before treatment and 14, 28, 42 and 56 days after treatment. Results Zeta-cypermethrin pour-on given at 2.5 mg/kg was equivalent to, or marginally more effective than a deltamethrin pour-on at 0.75 mg/kg. It eliminated B bovis and H eurysternus and gave good control of L vituli and S capillatus. Zeta-cypermethrin at 1 mg/kg gave good control of B bovis and H eurysternus but was not satisfactory against L vituli and S capillatus. Conclusion Zeta-cypermethrin pour-on, given at 2.5 mg/kg, is an effective treatment for cattle lice control. Zeta-cypermethrin, and other synthetic pyrethroid pour-ons, are the treatment of choice to control B bovis.

Effect of density on spatial distribution, pit formation and pit diameter of Myrmeleon acer Walker, (Neuroptera : Myrmeleontidae): patterns and processes

The effect of increasing population density on the formation of pits, their size and spatial distribution, and on levels of mortality was examined in the antlion Myrmeleon acer Walker. Antlions were kept at densities ranging from 0.4 to 12.8 individuals per 100 cm(2). The distribution of pits was regular or uniform across all densities, but antlions constructed proportionally fewer and smaller pits as density increased. Mortality through cannibalism was very low and only occurred at densities greater than five individuals per 100 cm(2). Antlions in artificially crowded situations frequently relocated their pits and when more space became available, individuals became more dispersed with time. Redistribution of this species results from active avoidance of other antlions and sand throwing associated with pit construction and maintenance, rather than any attempt to optimise prey capture per se.

Residues of zeta-cypermethrin in bovine tissues and milk following pour-on and spray application

The depletion of zeta-cypermethrin residues in bovine tissues and milk was studied. Beef cattle were treated three times at 3-week intervals with 1 ml 10 kg(-1) body weight of a 25 g litre(-1) or 50 g litre(-1) pour-on formulation (2.5 and 5.0 mg zeta-cypermethrin kg(-1) body weight) or 100 mg kg(-1) spray to simulate a likely worst-case treatment regime. Friesian and Jersey dairy cows were treated once with 2.5 mg zeta-cypermethrin kg(-1) in a pour-on formulation. Muscle, liver and kidney residue concentrations were generally less than the limit of detection (LOD = 0.01 mg kg(-1)). Residues in renal-fat and back-fat samples from animals treated with 2.5 mg kg(-1) all exceeded the limit of quantitation (LOQ = 0.05 mg kg(-1)), peaking at 10 days after treatment. Only two of five kidney fat samples were above the LOQ after 34 days, but none of the back-fat samples exceeded the LOQ at 28 days after treatment. Following spray treatments, fat residues were detectable in some animals but were below the LOQ at all sampling intervals. Zeta-cypermethrin was quantifiable (LOQ = 0.01 mg kg(-1)) in only one whole-milk sample from the Friesian cows (0.015 mg kg(-1), 2 days after treatment). In whole milk from Jersey cows, the mean concentration of zeta-cypermethrin peaked 1 day after treatment, at 0.015 mg kg(-1), and the highest individual sample concentration was 0.025 mg kg(-1) at 3 days after treatment. Residues in milk were not quantifiable beginning 4 days after treatment. The mean concentrations of zeta-cypermethrin in milk fat from Friesian and Jersey cows peaked two days after treatment at 0.197 mg kg(-1) and 0.377 mg kg(-1), respectively, and the highest individual sample concentrations were 2 days after treatment at 0.47 mg kg(-1) and 0.98 mg kg(-1), respectively. (C) 2001 Society of Chemical Industry.

Does the Mediterranean paradox extend to abdominal aortic aneurysm?

Background We sought to test, in men Undergoing ultrasound screening for abdominal aortic aneurysms (AAA) in Western Australia, clinical impressions that the prevalence of AAA is high in Dutch migrants and low in migrants from Mediterranean countries. Methods In a. population-based trial, men undergoing screening for AAA completed a questionnaire covering their place of birth, smoking habits and consumption of alcohol, meat, fish, salt and milk. We examined the variation by place of birth in the mean, median, 95th and 99th centiles of infrarenal aortic diameter and the prevalences of AAA defined by criteria of 30 mm, 50 mm and by the 95th and 99th centiles, in men born in Australia, of aortic diameter adjusted for height. Findings Overall, 12 203 (70.5%) of the 19 583 men took up the invitation to undergo ultrasound screening. The prevalence of AAA defined by absolute diameter was higher than average in men born in The Netherlands or Scotland (more of whom had ever smoked or smoked currently) and lower in men of Mediterranean origin (more of whom drank alcohol currently). There were no consistent relationships with simple dietary: data. Correction of aortic diameter for height eliminated the significant heterogeneity in prevalence of large AAA, although a threefold variation in prevalence of AAA exceeding the 95th centile of height-adjusted diameter in Australian men persisted. Interpretation In our cohort of men, which is subject to both 'healthy migrant' and 'survivor' effects, if it exists at all, any 'Mediterranean paradox' for AAA is more modest than that for coronary disease.

3D reconstruction and quantification of macropores using X-ray computed tomography and image analysis

Axial X-ray Computed tomography (CT) scanning provides a convenient means of recording the three-dimensional form of soil structure. The technique has been used for nearly two decades, but initial development has concentrated on qualitative description of images. More recently, increasing effort has been put into quantifying the geometry and topology of macropores likely to contribute to preferential now in soils. Here we describe a novel technique for tracing connected macropores in the CT scans. After object extraction, three-dimensional mathematical morphological filters are applied to quantify the reconstructed structure. These filters consist of sequences of so-called erosions and/or dilations of a 32-face structuring element to describe object distances and volumes of influence. The tracing and quantification methodologies were tested on a set of undisturbed soil cores collected in a Swiss pre-alpine meadow, where a new earthworm species (Aporrectodea nocturna) was accidentally introduced. Given the reduced number of samples analysed in this study, the results presented only illustrate the potential of the method to reconstruct and quantify macropores. Our results suggest that the introduction of the new species induced very limited chance to the soil structured for example, no difference in total macropore length or mean diameter was observed. However. in the zone colonised by, the new species. individual macropores tended to have a longer average length. be more vertical and be further apart at some depth. Overall, the approach proved well suited to the analysis of the three-dimensional architecture of macropores. It provides a framework for the analysis of complex structures, which are less satisfactorily observed and described using 2D imaging. (C) 2002 Elsevier Science B.V. All rights reserved.

Infiltration from surface and buried point sources: The average wetting water content

The assumption in analytical solutions for flow from surface and buried point sources of an average water content, (θ) over bar, behind the wetting front is examined. Some recent work has shown that this assumption fitted some field data well. Here we calculated (θ) over bar using a steady state solution based on the work by Raats [1971] and an exponential dependence of the diffusivity upon the water content. This is compared with a constant value of (θ) over bar calculated from an assumption of a hydraulic conductivity at the wetting front of 1 mm day(-1) and the water content at saturation. This comparison was made for a wide range of soils. The constant (θ) over bar generally underestimated (θ) over bar at small wetted radii and overestimated (θ) over bar at large radii. The crossover point between under and overestimation changed with both soil properties and flow rate. The largest variance occurred for coarser texture soils at low-flow rates. At high-flow rates in finer-textured soils the use of a constant (θ) over bar results in underestimation of the time for the wetting front to reach a particular radius. The value of (θ) over bar is related to the time at which the wetting front reaches a given radius. In coarse-textured soils the use of a constant value of (θ) over bar can result in an error of the time when the wetting front reaches a particular radius, as large as 80% at low-flow rates and large radii.

Infrarenal aortic diameter predicts all-cause mortality

Objective - To assess the relationship between infrarenal aortic diameter and subsequent all-cause mortality in men aged 65 years or older. Methods and Results - Aortic diameter was measured using ultrasound in 12 203 men aged 65 to 83 years as part of a trial of screening for abdominal aortic aneurysms. A range of cardiovascular risk factors was also documented. Mortality over the next 3 to 7 years was assessed using record linkage. Initial aortic diameter was categorized into 10 intervals, and the relationship between increasing diameter and subsequent mortality was explored using Cox proportional hazard models. Median diameter increased from 21.4 mm in the youngest men to 22.1 mm in the oldest men. The cumulative all-cause mortality increased in a graded fashion with increasing aortic diameter. Using the diameter interval 19 to 22 mm as the reference, the adjusted hazard ratio for all-cause mortality increased from 1.26 (95% CI: 1.09, 1.44; P = 0.001) for aortic diameters of 23 to 26 mm to 2.38 (95% CI: 1.22, 4.61; P = 0.011) for aortic diameters of 47 to 50 mm. Analysis of causes of death indicated that cardiovascular disease was an important contributor to this increase. Conclusion - Infrarenal aortic diameter is an independent marker of subsequent all-cause mortality.

In Vitro Antifungal Activity and Toxicity of Itraconazole in DMSA-PLGA Nanoparticles

Itraconazole (ITZ) is a drug used to treat various fungal infections and may cause side effects. The aim of this study was to develop and evaluate the in vitro activity of DMSA-PLGA nanoparticles loaded with ITZ against Paracoccidioides brasiliensis, as well as their cytotoxicity. Nanoparticles were prepared using the emulsification-evaporation technique and characterized by their encapsulation efficiency, morphology (TEM), size (Nanosight) and charge (zeta potential). Antifungal efficacy in P brasiliensis was determined by minimal inhibition concentration (MIC), and cytotoxicity using MU assay. ITZ was effectively incorporated in the PLGA-DMSA nanoparticles with a loading efficiency of 72.8 +/- 3.50%. The shape was round with a solid polymeric structure, and a size distribution of 174 +/- 86 nm (Average +/- SD). The particles were negatively charged. ITZ-NANO presented antifungal inhibition (MIC = 6.25 ug/mL) against P brasiliensis and showed lower in vitro cytotoxicity than free drug (ITZ).