Parallel-Operating Three-Phase Voltage Source Inverters – Circulating CurrentModeling, Analysis and Mitigation

The maximum realizable power throughput of power electronic converters may be limited or constrained by technical or economical considerations. One solution to this problemis to connect several power converter units in parallel. The parallel connection can be used to increase the current carrying capacity of the overall system beyond the ratings of individual power converter units. Thus, it is possible to use several lower-power converter units, produced in large quantities, as building blocks to construct high-power converters in a modular manner. High-power converters realized by using parallel connection are needed for example in multimegawatt wind power generation systems. Parallel connection of power converter units is also required in emerging applications such as photovoltaic and fuel cell power conversion. The parallel operation of power converter units is not, however, problem free. This is because parallel-operating units are subject to overcurrent stresses, which are caused by unequal load current sharing or currents that flow between the units. Commonly, the term ’circulatingcurrent’ is used to describe both the unequal load current sharing and the currents flowing between the units. Circulating currents, again, are caused by component tolerances and asynchronous operation of the parallel units. Parallel-operating units are also subject to stresses caused by unequal thermal stress distribution. Both of these problemscan, nevertheless, be handled with a proper circulating current control. To design an effective circulating current control system, we need information about circulating current dynamics. The dynamics of the circulating currents can be investigated by developing appropriate mathematical models. In this dissertation, circulating current models aredeveloped for two different types of parallel two-level three-phase inverter configurations. Themodels, which are developed for an arbitrary number of parallel units, provide a framework for analyzing circulating current generation mechanisms and developing circulating current control systems. In addition to developing circulating current models, modulation of parallel inverters is considered. It is illustrated that depending on the parallel inverter configuration and the modulation method applied, common-mode circulating currents may be excited as a consequence of the differential-mode circulating current control. To prevent the common-mode circulating currents that are caused by the modulation, a dual modulator method is introduced. The dual modulator basically consists of two independently operating modulators, the outputs of which eventually constitute the switching commands of the inverter. The two independently operating modulators are referred to as primary and secondary modulators. In its intended usage, the same voltage vector is fed to the primary modulators of each parallel unit, and the inputs of the secondary modulators are obtained from the circulating current controllers. To ensure that voltage commands obtained from the circulating current controllers are realizable, it must be guaranteed that the inverter is not driven into saturation by the primary modulator. The inverter saturation can be prevented by limiting the inputs of the primary and secondary modulators. Because of this, also a limitation algorithm is proposed. The operation of both the proposed dual modulator and the limitation algorithm is verified experimentally.

Financial and Environmental Impacts of a Dry Port to Facilitate Competitiveness of Two Major Transit Seaports of Finland

Environmental problems and issues have received more and more attention during the last decades. Reasons for this are different increased external costs such as congestion, CO2 emission, noise and accident costs. Transportation sector is the only sector with increasing external costs. The EU will increase its attention in decreasing the external costs of transport. Aim of this research was to find out if a dry port solution could decrease costs of transport, especially external costs. Dry port concept is an intermodal transport system, where inland transport between port and dry port is performed by rail transport instead of traditional road transport. In addition, dry ports offer similar services as ports. Research is conducted by performing a literature review about dry port concept and costs of transport, especially external costs of transport. Financial and environmental impacts of the dry port concept are studied by comparing costs of road and rail transport by cost accounting and with a simulation model. Location of dry port is researched with gravitational models. Results of the literature review are that rail transport is environmentally friendlier mode of transport than road transport. Cost model and simulation model show that if only costs of freight movement are considered, rail transport is more inexpensive transport mode than road transport in terms of internal and external costs. Because of that dry port concept could decrease costs of transport, especially external costs. Results of gravitational models are that city of Kouvola is in a good position to be a dry port. Russian transit traffic through Finland improves location of Kouvola to be a dry port.

Permanent Magnet Synchronous Machine for Parallel Hybrid Vehicle

The aim of this thesis is to describe hybrid drive design problems, the advantages and difficulties related to the drive. A review of possible hybrid constructions, benefits of parallel, series and series-parallel hybrids is done. In the thesis analytical and finite element calculations of permanent magnet synchronous machines with embedded magnets were done. The finite element calculations were done using Cedrat’s Flux 2D software. This machine is planned to be used as a motor-generator in a low power parallel hybrid vehicle. The boundary conditions for the design were found from Lucas-TVS Ltd., India. Design Requirements, briefly: • The system DC voltage level is 120 V, which implies Uphase = 49 V (RMS) in a three phase system. • The power output of 10 kW at base speed 1500 rpm (Torque of 65 Nm) is desired. • The maximum outer diameter should not be more than 250 mm, and the maximum core length should not exceed 40 mm. The main difficulties which the author met were the dimensional restrictions. After having designed and analyzed several possible constructions they were compared and the final design selected. Dimensioned and detailed design is performed. Effects of different parameters, such as the number of poles, number of turns and magnetic geometry are discussed. The best modification offers considerable reduction of volume.

E-PORT. Improving efficiency of Finnish port community by intelligent systems Final report of the Mobile Port project

The management of port-related supply chains is challenging due to the complex and heterogeneous operations of the ports with several actors and processes. That is why the importance of information sharing is emphasised in the ports. However, the information exchange between different port-related actors is often cumbersome and it still involves a lot of manual work and paper. Major ports and port-related actors usually have advanced information systems in daily use but these systems are seldom interoperable with each other, which prevents economies of scale to be reached. Smaller ports and companies might not be equipped with electronic data transmission at all. This is the final report of the Mobile port (MOPO) project, which has sought ways to improve the management and control of port-related sea and inland traffic with the aid of ICT technologies. The project has studied port community systems (PCS) used worldwide, evaluated the suitability of a PCS for the Finnish port operating environment and created a pilot solution of a Finnish PCS in the port of HaminaKotka. Further, the dry port concept and its influences on the transportation system have been explored. The Mobile Port project comprised of several literature reviews, interviews of over 50 port-related logistics and/or ICT professionals, two different kinds of simulation models as well as designing and implementing of the pilot solution of the Finnish PCS. The results of these multiple studies are summarised in this report. Furthermore, recommendations for future actions and the topics for further studies are addressed in the report. The study revealed that the information sharing in a typical Finnish port-related supply chain contains several bottlenecks that cause delays in shipments and waste resources. The study showed that many of these bottlenecks could be solved by building a port community system for the Finnish port community. Almost 30 different kinds of potential services or service entities of a Finnish PCS were found out during the study. The basic requirements, structure, interfaces and operation model of the Finnish PCS were also defined in the study. On the basis of the results of the study, a pilot solution of the Finnish PCS was implemented in the port of HaminaKotka. The pilot solution includes a Portconnect portal for the Finnish port community system (available at https://www.portconnect.fi) and two pilot applications, which are a service for handling the information flows concerning the movements of railway wagons and a service for handling the information flows between Finnish ports and Finland-Russian border. The study also showed that port community systems can be used to improve the environmental aspects of logistics in two different ways: 1) PCSs can bring direct environmental benefits and 2) PCSs can be used as an environmental tool in a port community. On the basis of the study, the development of the Finnish port community system should be continued by surveying other potential applications for the Finnish PCS. It is also important to study if there is need and resources to extend the Finnish PCS to operate in several ports or even on a national level. In the long run, it could be reasonable to clarify whether there would be possibilities to connect the Finnish PCS as a part of Baltic Sea wide, European-wide or even worldwide maritime and port-related network in order to get the best benefit from the system

Optimizing Customer Energy Invoice Calculation with Parallel Computation

Diplomityön tarkoituksena on optimoida asiakkaiden sähkölaskun laskeminen hajautetun laskennan avulla. Älykkäiden etäluettavien energiamittareiden tullessa jokaiseen kotitalouteen, energiayhtiöt velvoitetaan laskemaan asiakkaiden sähkölaskut tuntiperusteiseen mittaustietoon perustuen. Kasvava tiedonmäärä lisää myös tarvittavien laskutehtävien määrää. Työssä arvioidaan vaihtoehtoja hajautetun laskennan toteuttamiseksi ja luodaan tarkempi katsaus pilvilaskennan mahdollisuuksiin. Lisäksi ajettiin simulaatioita, joiden avulla arvioitiin rinnakkaislaskennan ja peräkkäislaskennan eroja. Sähkölaskujen oikeinlaskemisen tueksi kehitettiin mittauspuu-algoritmi.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

Inverse convection problem of simultaneous estimation of two boundary heat fluxes in parallel plate channels

This paper deals with the use of the conjugate gradient method of function estimation for the simultaneous identification of two unknown boundary heat fluxes in parallel plate channels. The fluid flow is assumed to be laminar and hydrodynamically developed. Temperature measurements taken inside the channel are used in the inverse analysis. The accuracy of the present solution approach is examined by using simulated measurements containing random errors, for strict cases involving functional forms with discontinuities and sharp-corners for the unknown functions. Three different types of inverse problems are addressed in the paper, involving the estimation of: (i) Spatially dependent heat fluxes; (ii) Time-dependent heat fluxes; and (iii) Time and spatially dependent heat fluxes.

Numerical Simulation of the Cavitation in the Hydrodynamic Lubrication of Journal Bearings: a Parallel Algorithm

In this paper we present an algorithm for the numerical simulation of the cavitation in the hydrodynamic lubrication of journal bearings. Despite the fact that this physical process is usually modelled as a free boundary problem, we adopted the equivalent variational inequality formulation. We propose a two-level iterative algorithm, where the outer iteration is associated to the penalty method, used to transform the variational inequality into a variational equation, and the inner iteration is associated to the conjugate gradient method, used to solve the linear system generated by applying the finite element method to the variational equation. This inner part was implemented using the element by element strategy, which is easily parallelized. We analyse the behavior of two physical parameters and discuss some numerical results. Also, we analyse some results related to the performance of a parallel implementation of the algorithm.

Seismic motion simulation based on Cassino Parallel Manipulator

In this paper we present a study of feasibility by using Cassino Parallel Manipulator (CaPaMan) as an earthquake simulator. We propose a suitable formulation to simulate the frequency, amplitude and acceleration magnitude of seismic motion by means of the movable platform motion by giving a suitable input motion. In this paper we have reported numerical simulations that simulate the three principal earthquake types for a seismic motion: one at the epicenter (having a vertical motion), another far from the epicenter (with the motion on a horizontal plane), and a combined general motion (with a vertical and horizontal motion).

The Environmental Status of the Port of HaminaKotka

This study is a part of the Ecologically Friendly Port Ust-Luga (EFP) project. The purpose of this study is to examine the environmental status of the Finnish ports and, more specifically, the Port of HaminaKotka. An analysis of the environmental status is performed mainly as a literature review, because the Finnish ports must comply with Finnish and EU legislation and with the binding international regulations and conventions created by different organizations. The International Maritime Organisation (IMO) has done groundbreaking work in the field of maritime safety and maritime environmental protection. The MARPOL convention has a great impact on decreasing pollution from international shipping and it applies to 99% of the world’s merchant tonnage. Pollution prevention covers: Oil pollution, Chemical pollution, Air pollution and GHG Emissions, Dumping of Wasted and Other Matters, Garbage, Sewage, Port Reception Facilities, Special Areas under MARPOL and Particularly Sensitive Sea Areas. There is also Pollution Prevention for other treaties like anti-fouling systems used on ships, the transfer of alien species by ships’ ballast water and the environmentally sound recycling of ships. There are more than twenty different EU and international regulations that influence ports and port operations in Finland. In addition, there is also national legislation that has an effect on Finnish ports. For the most part, the legislation for ports is common in the EU area, but the biggest and most important difference between the legislation in Finland and other EU countries is due to the Act on Environmental Impact Assessment Procedure. The Act states that the environmental impact assessment procedure shall be applied to projects that may have significant adverse environmental impacts, due to the special features of Finland`s nature and environment. In this Act, the term environmental impact refers to the direct and indirect effects inside and outside Finnish territory of a project or operations on human health, living conditions and amenity; soil, water, air, climate, organisms, interaction between them and biodiversity; community structure, buildings, landscape, townscape and cultural heritage; utilization of natural resources. In Finland, the Environmental Permit requires that ports collect all necessary information concerning environmental effects and make required reports to the Finnish authorities, stakeholders and the public. Commonly, environmental reporting is public and environmental achievements are emphasized in reporting and in media. At the moment, the problem in environmental reporting is that it’s difficult to compare data from different ports. There is enough data concerning the environmental effects and performance, but the manner of reporting and the quality of the data varies between ports. There are differences in the units and codes used, in some cases the information is not sufficient and it can even be rather unreliable. There are also differences regarding the subjects that are emphasized in reporting.

Energy-efficient control strategies for variable speed driven parallel pumping systems based on pump operation point monitoring with frequency converters

The pumping processes requiring wide range of flow are often equipped with parallelconnected centrifugal pumps. In parallel pumping systems, the use of variable speed control allows that the required output for the process can be delivered with a varying number of operated pump units and selected rotational speed references. However, the optimization of the parallel-connected rotational speed controlled pump units often requires adaptive modelling of both parallel pump characteristics and the surrounding system in varying operation conditions. The available information required for the system modelling in typical parallel pumping applications such as waste water treatment and various cooling and water delivery pumping tasks can be limited, and the lack of real-time operation point monitoring often sets limits for accurate energy efficiency optimization. Hence, alternatives for easily implementable control strategies which can be adopted with minimum system data are necessary. This doctoral thesis concentrates on the methods that allow the energy efficient use of variable speed controlled parallel pumps in system scenarios in which the parallel pump units consist of a centrifugal pump, an electric motor, and a frequency converter. Firstly, the suitable operation conditions for variable speed controlled parallel pumps are studied. Secondly, methods for determining the output of each parallel pump unit using characteristic curve-based operation point estimation with frequency converter are discussed. Thirdly, the implementation of the control strategy based on real-time pump operation point estimation and sub-optimization of each parallel pump unit is studied. The findings of the thesis support the idea that the energy efficiency of the pumping can be increased without the installation of new, more efficient components in the systems by simply adopting suitable control strategies. An easily implementable and adaptive control strategy for variable speed controlled parallel pumping systems can be created by utilizing the pump operation point estimation available in modern frequency converters. Hence, additional real-time flow metering, start-up measurements, and detailed system model are unnecessary, and the pumping task can be fulfilled by determining a speed reference for each parallel-pump unit which suggests the energy efficient operation of the pumping system.

The effect of environmentally differentiated port fees to shipping companies’ environmental investments

The pressure has grown to develop cost-effective emission reduction strategies in the Baltic Sea. The forthcoming stringent regulations of the International Maritime Organization for reducing harmful emissions of shipping in the Baltic Sea are causing increasing expenses for the operators. A market-based attitude towards pricing of economic incentives could be seen as a new approach for a successful application for the additional emission reduction of nitrogen oxides (NOx). In this study the aim is to understand the phenomenon of environmentally differentiated port fees and its effects on shipping companies’ emission reduction investments. The goal is to examine empirically the real-life effects of the possible environmental differentiated port fee system and the effect of environmentally differentiated port fees on NOx reduction investments in the Baltic Sea. The research approach of this study is nomothetical. In this study research questions are answered by analyzing the broad database of the Baltic Sea fleet. Also the framework of theory is confirmed and plays an important role in analyzing the research problem. Existing investment costs of NOx emission reduction technology to ship owners are estimated and compared to investment costs with granted discounts added to the cash flows. The statistical analysis in this study is descriptive. The major statistic examination of this study is the calculation of the net present values of investments with different port fee scenarios. This is done to investigate if the NOx technology investments could be economically reasonable. Based on calculations it is clear that the effect of environmentally differentiated port fees is not adequate to compensate the total investment costs for NOx reduction. If the investment decision is made only with profitability considerations, sources will prefer to emission abatement as long as incomes from the given subsidy exceeds their abatement costs. Despite of the results, evidence was found that shipping companies are nevertheless willing to invest on voluntary emission abatement technology. In that case, investment decision could be made with criteria of, for example, sustainable strategy or brand image. Combined fairway and port fee system or governmental regulations and recommendation could also function as additional incentives to compensate the investment costs. Also, the results imply that the use of NPV is not necessarily the best method to evaluate environmental investments. If the calculations would be done with more environmental methods the results would probably be different.

Plan de la ville et port de St. Petersbourg

Julkaisussa: Le petit atlas maritime : recueil de cartes et plans des quatre parties du monde en cinq volumes. Vol. IV

Gothebourg : ville forte port de mer sur l'océan de la province de Westro-Gotland au nord du destroit appellé l[a] Sond, située sur la rivière d[e] Trollhette

Kartta kuuluu A. E. Nordenskiöldin kokoelmaan