Ionized-air-treated curaua fibers as reinforcement for phenolic matrices

Curaua fibers were treated with ionized air to improve the fiber/phenolic matrix adhesion.The treatment with ionized air did not change the thermal stability of the fibers. The impact strength increased with increase in the fiber treatment time. SEM micrographs of the fibers showed that the ionized air treatment led to separation of the fiber bundles. Treatment for 12 h also caused a partial degradation of the fibers, which prompted the matrix to transfer the load to a poorer reinforcing agent during impact, thereby decreasing the impact strength of the related composite. The composites reinforced with fibers treated with ionized air absorbed less water than those reinforced with untreated fibers.

Sisal chemically modified with lignins: Correlation between fibers and phenolic composites properties

Sisal fibers have been chemically modified by reaction with lignins, extracted from sugarcane bagasse and Pinus-type wood and then hydroxymethylated, to increase adhesion in resol-type phenolic thermoset matrices. Inverse gas chromatography (IGC) results showed that acidic sites predominate for unmodified/modified sisal fibers and for phenolic thermoset, indicating that the phenolic matrix has properties that favor the interaction with sisal fibers. The IGC results also showed that the phenolic thermoset has a dispersive component closer to those of the modified fibers suggesting that thermoset interactions with the less polar modified fibers are favored. Surface SEM images of the modified fibers showed that the fiber bundle deaggregation increased after the treatment, making the interfibrillar structure less dense in comparison with that of unmodified fibers, which increased the contact area and encouraged microbial biodegradation in simulated soil. Water diffusion was observed to be faster for composites reinforced with modified fibers, since the phenolic resin penetrated better into modified fibers, thereby blocking water passage through their channels. Overall, composites` properties showed that modified fibers promote a significant reduction in the hydrophilic character, and consequently of the reinforced composite without a major effect on impact strength and with increased storage modulus. (c) 2008 Elsevier Ltd. All rights reserved.

Biobased composites from tannin-phenolic polymers reinforced with coir fibers

Tannin-phenolic polymers prepared using tannin, a macromolecule obtained from natural sources, were used in the preparation of composites reinforced with coir fibers. The composites based on tannin-phenolic polymers (50% (w/w) of tannin as substitute of the phenol) were prepared using the coir fibers as reinforcement (30-70% (w/w), 3.0-6.0 cm, randomly distributed). The Izod impact strength of the composites showed an improvement in this property due to the incorporation of coir fibers in the tannin-phenolic matrices. The SEM images showed excellent adhesion at the fiber/matrix interface. The coir fiber had bundles regularly spaced, which enhanced the diffusion of the resin into the fiber. In addition, the high lignin content of this fiber results in a high concentration of aromatic rings, which increased the compatibility with the matrix. The values of the diffusion coefficient of water, determined using Fick`s laws, show that there was no correlation between the fiber percentage and the water diffusion. The DMTA curves showed that the storage moduli of the composites reinforced with coir fibers were considerably higher than that of the thermoset, and the increase in the proportion of fibers led to a proportional increase in the storage moduli of these materials. The biobased composites obtained have potential for non-structural applications, such as in the internal parts of automotives vehicles. To our knowledge, this is the first study on this kind of biobased composites. (C) 2010 Elsevier B.V. All rights reserved.

Valorization of an Industrial Organosolv-Sugarcane Bagasse Lignin: Characterization and Use as a Matrix in Biobased Composites Reinforced With Sisal Fibers

In the present study, the main focus was the characterization and application of the by-product lignin isolated through an industrial organosolv acid hydrolysis process from sugarcane bagasse, aiming at the production of bioethanol. The sugarcane lignin was characterized and used to prepare phenolic-type resins. The analysis confirmed that the industrial sugarcane lignin is of HGS type, with a high proportion of the less substituted aromatic ring p-hydroxyphenyl units, which favors further reaction with formaldehyde. The lignin-formaldehyde resins were used to produce biobased composites reinforced with different proportions of randomly distributed sisal fibers. The presence of lignin moieties in both the fiber and matrix increases their mutual affinity, as confirmed by SEM images, which showed good adhesion at the biocomposite fiber/matrix interface. This in turn allowed good load transference from the matrix to the fiber, leading to biobased composites with good impact strength (near 500 J m(-1) for a 40 wt% sisal fiber-reinforced composite). The study demonstrates that sugarcane bagasse lignin obtained from a bioethanol plant can be used without excessive purification in the preparation of lignocellulosic fiber-reinforced biobased composites displaying high mechanical properties. Biotechnol. Bioeng. 2010;107: 612-621. (C) 2010 Wiley Periodicals, Inc.

Biobased composites from glyoxal-phenolic resins and sisal fibers

Lignocellulosic materials can significantly contribute to the development of biobased composites. In this work, glyoxal-phenolic resins for composites were prepared using glyoxal, which is a dialdehyde obtained from several natural resources. The resins were characterized by (1)H, (13)C, (2)D, and (31)P NMR spectroscopies. Resorcinol (10%) was used as an accelerator for curing the glyoxal-phenol resins in order to obtain the thermosets. The impact-strength measurement showed that regardless of the cure cycle used, the reinforcement of thermosets by 30% (w/w) sisal fibers improved the impact strength by one order of magnitude. Curing with cycle 1 (150 degrees C) induced a high diffusion coefficient for water absorption in composites, due to less interaction between the sisal fibers and water. The composites cured with cycle 2 (180 degrees C) had less glyoxal resin coverage of the cellulosic fibers, as observed by images of the fractured interface observed by SEM. This study shows that biobased composites with good properties can be prepared using a high proportion of materials obtained from natural resources. (C) 2009 Elsevier Ltd. All rights reserved.

Sisal Fibers Treated with NaOH and Benzophenonetetracarboxylic Dianhydride as Reinforcement of Phenolic Matrix

In this work, composites based on a phenolic matrix and untreated- and treated sisal fibers were prepared. The treated sisal fibers used were those reacted with NaOH 2% solution and esterified using benzophenonetetracarboxylic dianhydride (BTDA). These treated fibers were modified with the objective of improving the adhesion of the fiber-matrix interface, which in turn influences the properties of the composites. BTDA was chosen as the esterifying agent to take advantage of the possibility of introducing; the polar and aromatic groups that are also present in the matrix structure into the surface of the fiber, which could then intensify the interactions occurring in the fiber-matrix interface. The fibers were then analyzed by SEM and FTIR to ascertain their chemical composition. The results showed that the fibers had been successfully modified. The composites (reinforced with 15%, w/w of 3.0 cm length sisal fiber randomly distributed) were characterized by SEM, impact strength, and water absorption capacity. In the tests conducted, the response of the composites was affected both by properties of the matrix and the fibers, besides the interfacial properties of the fiber-matrix. Overall, the results showed that the fiber treatment resulted in a composite that was less hygroscopic although with somewhat lower impact strength, when compared with the composite reinforced with untreated sisal fibers. (C) 2009 Wiley Periodicals, Inc. J Appl Polym Sci 115: 269-276, 2010

Pineapple Leaf Fibers for Composites and Cellulose

Pineapple leaf fiber (PALF) which is rich in cellulose, abundantly available, relatively inexpensive, low density, nonabrasive nature, high filling level possible, low energy consumption, high specific properties, biodegradability and has the potential for polymer reinforcement. The utilization of pineapple leaf fiber (PALF) as reinforcements in thermoplastic and thermosetting resins in micro and nano form for developing low cost and lightweight composites is an emerging field of research in polymer science and technology. In this paper we examines the industrial applicabiliy of PALF, mainly for production of composite materials and special papers, chemical feedstocks (bromelin enzyme) and fabrics.

Phenolic matrices and sisal fibers modified with hydroxy terminated polybutadiene rubber: Impact strength, water absorption, and morphological aspects of thermosets and composites

The aim of the present work was to investigate the toughening of phenolic thermoset and its composites reinforced with sisal fibers, using hydroxyl-terminated polybutadiene rubber (HTPB) as both impact modifier and coupling agent. Substantial increase in the impact strength of the thermoset was achieved by the addition 10% of HTPB. Scanning electron microscopy (SEM) images of the material with 15% HTPB content revealed the formation of some rubber aggregates that reduced the efficiency of the toughening mechanism. In composites, the toughening effect was observed only when 2.5% of HTPB was added. The rubber aggregates were found located mainly at the matrix-fiber interface suggesting that HTPB could be used as coupling agent between the sisal fibers and the phenolic matrix. A composite reinforced with sisal fibers pre-impregnated with HTPB was then prepared; its SEM images showed the formation of a thin coating of HTPB on the surface of the fibers. The ability of HTBP as coupling agent between sisal fibers and phenolic matrix was then investigated by preparing a composite reinforced with sisal fibers pre-treated with HTPB. As revealed by its SEM images, the HTPB pre-treatment of the fibers resulted on the formation of a thin coating of HTPB on the surface of the fibers, which provided better compatibility between the fibers and the matrix at their interface, resulting in a material with low water absorption capacity and no loss of impact strength. (C) 2009 Elsevier B.V. All rights reserved.

Thermoset matrix reinforced with sisal fibers: Effect of the cure cycle on the properties of the biobased composite

Thermoset phenolic composites reinforced with sisal fibers were prepared to optimize the cure step. In the present study, processing parameters such as pressure, temperature, and time interval were varied to control the vaporization of the water generated as a byproduct during the crosslinking reaction. These molecules can vaporize forming voids, which in turn affect the final material properties. The set of results on impact strength revealed that the application of higher pressure before the gel point of the phenolic matrix produced composites with better properties. The SEM images showed that the cure cycle corresponding to the application of higher values of molding pressure at the gel point of the phenolic resin led to the reduction of voids in the matrix. In addition, the increase in the molding pressure during the cure step increased the resin interdiffusion. Better filling of the fiber channels decreased the possibility of water molecules diffusing through the internal spaces of the fibers. These molecules then diffused mainly through the bulk of the thermoset matrix, which led to a decrease in the water diffusion coefficient (D) at all three temperatures (25, 55 and 70 degrees C) considered in the experiments. (C) 2009 Elsevier Ltd. All rights reserved.

Characterization of banana, sugarcane bagasse and sponge gourd fibers of Brazil

In recent times, increasing attention has been paid to the use of renewable resources particularly of plant origin keeping in view the ecological concerns, renewability and many governments passing laws for the use of such materials. On the other hand, despite abundant availability of lignocellulosic materials in Brazil, very few attempts have been made about their utilization, probably due to lack of sufficient structure/property data. Systematic studies to know their properties and morphology may bridge this gap while leading to value addition to these natural materials. Chemical composition, X-ray powder diffraction, and morphological studies and thermal behavior aspects in respect of banana, sugarcane bagasse sponge gourd fibers of Brazilian origin are presented. Chemical compositions of the three fibers are found to be different than those reported earlier. X-ray diffraction patterns of these three fibers exhibit mainly cellulose type I structure with the crystallinity indices of 39%, 48% and 50% respectively for these fibers. Morphological studies of the fibers revealed different sizes and arrangement of cells. Thermal stability of all the fibers is found to be around 200 degrees C. Decomposition of both cellulose and hemicelluloses in the fibers takes place at 300 degrees C and above, while the degradation of fibers takes place above 400 degrees C. These data may help finding new uses for these fibers. (C) 2009 Elsevier B.V. All rights reserved.

Sistemas de produção de carvão vegetal existentes no Brasil: uma análise de viabilidade econômica

O carvão vegetal tem um papel de destaque entre as biomassas consumidas no Brasil. Seu uso em larga escala na indústria siderúrgica para a produção de ferro gusa fez do país um dos maiores produtores e consumidores mundiais de carvão vegetal. A matéria-prima abundante, bem como a falta de preocupação com fatores ambientais e sociais, permitiu no passado que se atentasse apenas ao fator econômico; e a tecnologia de produção deste combustível/insumo se desenvolveu muito pouco ao longo de quase toda a sua história no Brasil até os anos mais recentes. Nas duas últimas décadas, quando se intensificou a preocupação social e ambiental e esses fatores ganharam relevância na análise da viabilidade de projetos tanto a serem implantados, quanto já existentes, a produção de carvão vegetal passou a ser identificada como extremamente rudimentar e impactante ao meio ambiente e sociedade onde se localiza. Neste trabalho buscou-se analisar a viabilidade econômica de quatro sistemas de produção de carvão existentes no Brasil. O sistema mais rudimentar, comumente chamado de “rabo quente”, um sistema ainda de alvenaria, com um pouco mais desenvolvimento tecnológico conhecido como forno retangular, e dois sistemas que utilizam fornos metálicos para buscar menor tempo do processo de carbonização (devido ao mais rápido resfriamento do sistema) e que têm, ambos, uma preocupação ambiental maior e buscam emitir menos poluentes e oferecer uma condição de trabalho mais adequada, refletindo também positivamente sob o aspecto sócio-ambiental. Percebe-se que em termos de implantação, obviamente, os sistemas que envolvem um pouco mais de tecnologia são bem mais dispendiosos em investimento inicial, porém, há resultados animadores do ponto de vista de retorno do investimento e possibilidades de agregação de valor que tendem a atrair o investimento especialmente dos grandes grupos siderúrgicos consumidores, que têm se preocupado cada vez mais em investir tanto na produção de matéria-prima, com grandes áreas de reflorestamento, quanto na produção sustentável do carvão vegetal.

Alternativas para a aplicação de coagulante vegetal à base de tanino no tratamento do efluente de uma lavanderia industrial

A lavagem de roupas é um importante serviço para a sociedade moderna. Os efluentes de lavanderias industriais, de maneira geral, contêm sujeiras removidas das roupas e substâncias adicionadas na lavagem que normalmente são tratados por processo físicoquímico de coagulação/floculação/sedimentação. Os sais de alumínio e os produtos convencionalmente empregados para a correção do pH são agentes inorgânicos não biodegradáveis que acrescentam elementos químicos à água ou ao lodo. Como principal dificuldade do processo destaca-se o lodo inorgânico gerado, de difícil manuseio por parte das empresas em função do volume gerado e do elevado teor de umidade. O objetivo geral da presente da pesquisa foi avaliar a aplicabilidade e a eficiência do uso de um coagulante vegetal, basicamente tanino modificado pela reação de Mannich, no tratamento do efluente de uma lavanderia industrial. Realizaram-se estudos de coagulação/floculação com reagentes tradicionais (sulfato de alumínio e poliacrilamida catiônica), coagulação/floculação com um coagulante alternativo (tanino catiônico e poliacrilamida aniônica) e adsorção/coagulação/floculação (carvão ativado em pó, tanino catiônico e poliacrilamida aniônica). A dosagem de reagentes foi otimizada através de “Teste de Jarros” e a eficiência de cada uma das alternativas foi avaliada em termos de remoção de sólidos sedimentáveis, sólidos suspensos, turbidez, DQO e surfactantes. Analisou-se a contribuição de cada um destes processos em termos de ânions cloretos e sulfatos residual bem como a toxicidade aguda para populações do microcrustáceo Daphnia similis e do peixe Pimephales promelas. A massa e o volume de lodo gerado em cada processo foi quantificado e o lodo caracterizado em termos de sua periculosidade conforme a NBR 10.004 e comportamento termogravimétrico Os resultados demonstram que, em termos da legislação vigente, o efluente bruto não atende aos padrões de carga orgânica (DQO) e surfactantes. Os ensaios ecotoxicológicos indicam que o efluente pode ser considerado extremamente tóxico para o microcrustáceo Daphnia similis, como para o peixe Pimephales promelas. O tratamento do efluente realizado por coagulação/floculação usando o tanino catiônico como agente coagulante remove os sólidos suspensos e uma fração considerável da carga orgânica e de surfactantes. Em termos da legislação vigente, o efluente somente não atende ao padrão referente ao lançamento de surfactantes. Os ensaios ecotoxicológicos indicam que efluente passa a ser considerado pouco tóxico para a Daphnia similis e ainda tóxico para o peixe Pimephales promelas. O tratamento do efluente por heteroagregação entre carvão ativado, tanino catiônico e polímero floculante permite remover os sólidos suspensos, e níveis mais significativos de carga orgânica e de surfactantes, atendendo a todos padrões de lançamento exigidos para este tipo de efluente. Os ensaios ecotoxicológicos indicam que efluente passa a ser considerado não tóxico para a Daphnia similis e para a Pimephales promelas. O lodo gerado com o uso do tanino catiônico como agente coagulante é classificado como um resíduo Não Inerte - Classe II conforme a NBR 10.004, unicamente devido ao fato de exceder a concentração de surfactantes no ensaio de solubilização conforme a NBR 10.006. O lodo apresenta ainda um alto teor de matéria orgânica, o que facilita a sua eliminação por tratamento térmico ou biológico Comparado ao agente coagulante tradicionalmente empregado para tal fim, o sulfato de alumínio, o tanino catiônico apresentou resultados em relação a qualidade do efluente tratado muito parecidos. Entretanto, pode-se citar algumas evidentes vantagens: menor custo, uso de uma matéria prima renovável, menor contribuição de ânions sulfatos ao efluente final, menor geração de massa de lodo, e obtenção de um lodo orgânico com maior facilidade de eliminação. Esses fatores todos permitem concluir que a substituição do sulfato de alumínio pelo tanino catiônico contribui para um processo de tratamento de efluentes mais limpo.

Gene delivery using dendrimer/pDNA complexes immobilized in electrospun fibers using the layer-by-layer technique

Tissue engineering is an important branch of regenerative medicine that uses cells, materials (scaffolds), and suitable biochemical and physicochemical factors to improve or replace specific biological functions. In particular, the control of cell behavior (namely, of cell adhesion, proliferation and differentiation) is a key aspect for the design of successful therapeutical approaches. In this study, poly(lactic-co-glycolic acid) (PLGA) fiber mats were prepared using the electrospinning technology (the fiber diameters were in the micrometer range). Furthermore, the electrospun fiber mats thus formed were functionalized using the layer-by- layer (LbL) technique with chitosan and alginate (natural and biodegradable polyelectrolytes having opposite charges) as a mean for the immobilization of pDNA/dendrimer complexes. The polyelectrolyte multilayer deposition was confirmed by fluorescence spectroscopy using fluorescent-labeled polyelectrolytes. The electrospun fiber mats coated with chitosan and alginate were successfully loaded with complexes of pDNA and poly(amidoamine) (PAMAM) dendrimers (generation 5) and were able of releasing them in a controlled manner along time. In addition, these mats supported the adhesion and proliferation of NIH 3T3 cells and of human mesenchymal stem cells (hMSCs) in their surface. Transfection experiments using a pDNA encoding for luciferase showed the ability of the electrospun fiber mats to efficiently serve as gene delivery systems. When a pDNA encoding for bone morphogenetic protein-2 (BMP-2) was used, the osteoblastic differentiation of hMSCs cultured on the surface of the mats was promoted. Taken together, the results revealed that merging the electrospinning technique with the LbL technique, can be a suitable methodology for the creation of biological active matrices for bone tissue engineering.

Adsorção de cobre e cromo utilizando fibra de sisal visando o tratamento da água produzida pela indústria petrolífera

Currently, the oil industry is the biggest cause of environmental pollution. The objective was to reduce the concentration of copper and chromium in the water produced by the oil industry. It was used as adsorbent natural sisal fiber Agave sp treated with nitric acid and sodium hydroxide. All vegetable fibers have physical and morphological properties that enablies the adsorption of pollutants. The basic composition of sisal is cellulose, hemicellulose and lignin. The features are typically found in the characterization of vegetable fibers, except the surface area that was practically zero. In the first stage of adsorption, it was evaluated the effect of temperature and time skeeking to optimize the execution of the factorial design. The results showed that the most feasible fiber was the one treated with acid in five hours (30°C). The second phase was a factorial design, using acid and five hours, this time was it determined in the first phase. The tests were conducted following the experimental design and the results were analyzed by statistical methods in order to optimize the main parameters that influence the process: pH, concentration (mol / L) and fiber mass/ metal solution volume. The volume / mass ratio factor showed significant interference in the adsorption process of chromium and copper. The results obtained after optimization showed that the highest percentages of extraction (98%) were obtained on the following operating conditions: pH: 5-6, Concentration: 100 ppm and mass/ volume: 1 gram of fiber/50mL solution. The results showed that the adsorption process was efficient to remove chromium and copper using sisal fibers, however, requiring further studies to optimize the process.