Numerical investigation of the effects of drill geometry on drilling induced delamination of carbon fiber reinforced composites

Drilling is a major process in the manufacturing of holes required for the assemblies of composite laminates in aerospace industry. Simulation of drilling process is an effective method in optimizing the drill geometry and process parameters in order to improve hole quality and to reduce the drill wear. In this research we have developed three-dimensional (3D) FE model for drilling CFRP. A 3D progressive intra-laminar failure model based on the Hashin's theory is considered. Also an inter-laminar delamination model which includes the onset and growth of delamination by using cohesive contact zone is developed. The developed model with inclusion of the improved delamination model and real drill geometry is used to make comparison between the step drill of different stage ratio and twist drill. Thrust force, torque and work piece stress distributions are estimated to decrease by the use of step drill with high stage ratio. The model indicates that delamination and other workpiece defects could be controlled by selection of suitable step drill geometry. Hence the 3D model could be used as a design tool for drill geometry for minimization of delamination in CFRP drilling. © 2013 Elsevier Ltd.

Delamination and wear in drilling of carbon-fiber reinforced plastic composites using multilayer TiAlN/TiN PVD-coated tungsten carbide tools

This study aims to investigate drilling process in carbon-fiber reinforced plastic (CFRP) composites with multilayer TiAlN/TiN PVD-coated tungsten carbide drill. The effect of process parameters have been investigated in drilling of Hexcel M21-T700GC. Thrust force and torque were measured online throughout the drilling experiments. Delamination were observed using optical microscope and analyzed via a developed algorithm based on digital image processing technique. Surface roughness of each hole was measured using a surface profilometer. In addition, the progression of tool wear in various surfaces of drill was observed using tool microscope and measured using image software. Our results indicate that the thrust force and torque increased with the increasing cutting speed and feed rate. Delamination and average surface roughness that rose with the increase in feed rate, however, decreased with the increasing cutting speed. The average surface roughness tended to increase with the increase in feed rate and decrease with the increasing cutting speed in drilling of carbon-fiber reinforced plastic (CFRP). Feed rate was found as the predominant factor on the drilling outputs. Abrasive wear was observed on both flank and relief surfaces, which created edge wear on cutting edges. No sign of chipping or plastic deformation has been observed on the surfaces of drills. © 2012 The Author(s).

Failed filament eruption inside a coronal mass ejection in active region 11121

Aims. We study the formation and evolution of a failed filament eruption observed in NOAA active region 11121 near the southeast
limb on November 6, 2010.
Methods. We used a time series of SDO/AIA 304, 171, 131, 193, 335, and 94 Å images, SDO/HMI magnetograms, as well as ROSA
and ISOON Hα images to study the erupting active region.
Results. We identify coronal loop arcades associated with a quadrupolar magnetic configuration, and show that the expansion and
cancellation of the central loop arcade system over the filament is followed by the eruption of the filament. The erupting filament
reveals a clear helical twist and develops the same sign of writhe in the form of inverse γ-shape.
Conclusions. The observations support the “magnetic breakout” process in which the eruption is triggered by quadrupolar reconnection
in the corona. We propose that the formation mechanism of the inverse γ-shape flux rope is the magnetohydrodynamic helical
kink instability. The eruption has failed because of the large-scale, closed, overlying magnetic loop arcade that encloses the active
region

Creating an Inclusive Society… How Close are We in Relation to Autism Spectrum Disorder? A General Population Survey

BackgroundChildren with autism spectrum disorder are increasingly educated in mainstream classrooms in the United Kingdom (Wilkinson & Twist, Autism and Educational Assessment: UK Policy and Practice. NFER, Slough, 2010), and some employers are now specifically seeking out staff on the autism spectrum. Does that mean that we are living in an inclusive society' [United Nations Department of Economic and Social Affairs (UNDESA), Creating an Inclusive Society: Practical Strategies to Promote Social Integration 2008], in the sense that inequalities are reduced and full economic, social and cultural participation is advanced for individuals with autism?

MethodsA general population survey was conducted to assess how close we, as a society, are to an inclusive society for individuals with autism in Northern Ireland. Public attitudes were examined to (i) visibility and social interaction, (ii) aetiology, needs and interventions, and (iii) rights and resources.

ResultsA stratified, representative sample of 1204 adults took part in the survey; of these, 989 were aware of autism and their attitudes and behavioural projections reflected a mix of acceptance and denunciation. The level of confusion with regard to interventions reflected the general uncertainty within UK policy regarding meeting the needs of individuals on the autism spectrum (International Journal of Disability, Development and Education 61, 134, 2014a).

ConclusionTherefore, it seems that inclusion is working to an extent, but more clarity is needed with regard to adequate education, intervention and support for individuals with autism.

Formação cívica e formação de professores: limites e potencialidades

A reorganização curricular do Ensino Básico de 2001 representou uma mudança de paradigma: uma aposta na flexibilidade, na integração e na autonomia. Uma das principais inovações desta reforma foi a criação de áreas curriculares não disciplinares, entre elas a Formação Cívica. Uma década volvida qual o impacto desta decisão? Estudos anteriores revelaram o uso administrativo e burocrático da Formação Cívica, ao serviço do Diretor de Turma e das suas responsabilidades de gestão da turma e resolução de conflitos. Num cenário de defraudamento das expetativas iniciais depositadas neste domínio não disciplinar e convencidos que estávamos da importância de potenciar espaços reais de promoção da Cidadania nas escolas desencadeámos um estudo de modelização dupla investigação-formação que nos permitisse compreender qual o papel da formação de professores neste domínio e os respetivos limites e potencialidades da Formação Cívica. Com base no pressuposto de que a ação de qualquer professor em contexto de sala de aula depende do conhecimento profissional que possui acerca de um determinado domínio curricular e reconhecendo a ausência de mecanismos de formação específica para a concretização dos tempos letivos de Formação Cívica, estruturámos o nosso trabalho com o intuito de contribuir para a construção de conhecimento sobre a natureza da formação de professores em Formação Cívica. Realizado no contexto da formação contínua de professores, o presente estudo desenvolveu-se em duas etapas fundamentais que se foram interligando entre momentos de investigação, reflexão, formação, recolha e análise de dados. A abordagem metodológica que se delineou para todas as fases assumiu um cariz qualitativo e crítico-interpretativo. Numa primeira fase, realizámos um estudo exploratório que nos permitiu identificar conceções, práticas e contextos no domínio da Formação Cívica. Selecionámos uma escola no distrito de Aveiro e entrevistámos 10 professores do 3.º CEB, coordenação e direção da escola, analisámos documentos oficiais e observámos aulas. Concluímos que a operacionalização da Formação Cívica está refém de um conjunto de condicionalismos, entre eles: a ausência de orientações curriculares; a sobreposição de funções do Diretor de Turma; o não reconhecimento das funções pedagógicas de uma área não disciplinar; a ausência de preparação científica e pedagógica dos professores responsáveis por este tempo letivo. A segunda fase do estudo contemplou a conceção, desenvolvimento, implementação e avaliação de um percurso formativo projetado com base nos resultados do estudo exploratório e da revisão da literatura realizada para o efeito. O percurso formativo, desenvolvido na modalidade de Oficina de Formação (OF), envolveu e alicerçou-se no potencial das tecnologias (participação numa comunidade online; criação de blogues; desenvolvimento de recursos digitais) e envolveu sete professores. Dos professores participantes na OF, foram analisados em detalhe o percurso formativo de três professoras de diferentes escolas do ensino básico e com diferentes níveis de experiência letiva em Formação Cívica. A realização deste percurso formativo permitiu-nos: i) identificar processos de reconstrução do conceito de cidadania e do lugar da Formação Cívica; ii) identificar uma visão mais alargada e transformadora da Formação Cívica ao invés de abordagens restritas de cariz administrativo; ii) analisar a importância da partilha de experiências, do feedback, do suporte e da reflexão no processo formativo para o desenvolvimento das práticas pedagógico-didáticas; iv) conceptualizar o conhecimento profissional docente associado à Formação Cívica. Consideramos que este estudo contribui para a necessária reflexão sobre o espaço e o papel da Educação para a Cidadania no sistema educativo Português, assim como para o debate da afirmação da Formação Cívica (com esta ou outra designação mas necessariamente com novos contornos), em particular no currículo do ensino básico. Sustentamos ainda a importância fundamental da formação contínua (de carácter ativo e reflexivo) e da construção partilhada do conhecimento para o desenvolvimento profissional dos professores de Formação Cívica, necessário para dar resposta aos desafios da Educação para a Cidadania.

Joaquim Rodrigo:a contínua reinvenção da pintura

Tese de doutoramento, História (História da Arte), Universidade de Lisboa, Faculdade de Letras, 2014

Efeito da ligadura funcional na prevenção da recorrência da entorse do tornozelo numa equipa de basquetebol feminino

Introdução: O basquetebol é considerado um desporto de alto risco para a ocorrência de lesões, nomeadamente das entorses do tornozelo. Como a história de lesão anterior é um fator de risco para a ocorrência de entroses têm-se desenvolvido estratégias de prevenção para evitar as recidivas, um dos métodos possíveis é o recurso a ligaduras funcionais em “tape”. Objetivo: Neste trabalho vai-se verificar se as ligaduras funcionais em “tape” previnem a recorrência de entorse do tornozelo, numa equipa feminina de basquetebol sub-16. Métodos: A amostra é composta por 9 atletas de basquetebol sub-16 com história de entorse no tornozelo na época precedente, vão-se utilizar ligaduras funcionais no tornozelo. Resultados: A entorse teve 9 registos na época anterior. Não houve registo de qualquer lesão da tibiotársica nos treinos ou jogos, durante a aplicação das ligaduras. Conclusão: A utilização das ligaduras funcionais no grupo estudado, como método de prevenção foi eficaz, não se registando qualquer entorse no decorrer das atividades desportivas (treinos/jogos).

Tool effects on hybrid laminates drilling

Fiber reinforced plastics are increasing their importance as one of the most interesting groups of material on account of their low weight, high strength, and stiffness. To obtain good quality holes, it is important to identify the type of material, ply stacking sequence, and fiber orientation. In this article, the drilling of quasi-isotropic hybrid carbon +glass/epoxy plates is analyzed. Two commercial drills and a special step drill are compared considering the thrust force and delamination extension. Results suggest that the proposed step drill can be a suitable option in laminate drilling.

Delamination analysis of carbon fibre reinforced laminates: evaluation of a special step drill

Drilling of carbon fibre/epoxy laminates is usually carried out using standard drills. However, it is necessary to adapt the processes and/or tooling as the risk of delamination, or other damages, is high. These problems can affect mechanical properties of produced parts, therefore, lower reliability. In this paper, four different drills – three commercial and a special step (prototype) – are compared in terms of thrust force during drilling and delamination. In order to evaluate damage, enhanced radiography is applied. The resulting images were then computational processed using a previously developed image processing and analysis platform. Results show that the prototype drill had encouraging results in terms of maximum thrust force and delamination reduction. Furthermore, it is possible to state that a correct choice of drill geometry, particularly the use of a pilot hole, a conservative cutting speed – 53 m/min – and a low feed rate – 0.025 mm/rev – can help to prevent delamination.

Microbiota abnormalities in inflammatory airway diseases - Potential for therapy.

Increasingly the development of novel therapeutic strategies is taking into consideration the contribution of the intestinal microbiota to health and disease. Dysbiosis of the microbial communities colonizing the human intestinal tract has been described for a variety of chronic diseases, such as inflammatory bowel disease, obesity and asthma. In particular, reduction of several so-called probiotic species including Lactobacilli and Bifidobacteria that are generally considered to be beneficial, as well as an outgrowth of potentially pathogenic bacteria is often reported. Thus a tempting therapeutic approach is to shape the constituents of the microbiota in an attempt to restore the microbial balance towards the growth of 'health-promoting' bacterial species. A twist to this scenario is the recent discovery that the respiratory tract also harbors a microbiota under steady-state conditions. Investigators have shown that the microbial composition of the airway flora is different between healthy lungs and those with chronic lung diseases, such as asthma, chronic obstructive pulmonary disease as well as cystic fibrosis. This is an emerging field, and thus far there is very limited data showing a direct contribution of the airway microbiota to the onset and progression of disease. However, should future studies provide such evidence, the airway microbiota might soon join the intestinal microbiota as a target for therapeutic intervention. In this review, we highlight the major advances that have been made describing the microbiota in chronic lung disease and discuss current and future approaches concerning manipulation of the microbiota for the treatment and prevention of disease.

The contribution of skate blade properties to skating speed

The purpose of the study was to investigate the relative contribution of skate blade properties to on-ice skating speed. Thirty-two male ice hockey players (mean age = 19±2.65 yrs.) representing the Ontario Minor Hockey Association (OMHA; Midget AAA and Junior), Canadian Inter University Sport (CIS: Varsity), Ontario hockey league (OHL) and East Coast Hockey League (ECHL), and the playing positions of forwards (n=18) and defense (n=14) were recruited to participate. Skate related equipment worn by the players for the purpose of the research was documented and revealed that 80% of the players wore Bauer skates, Tuuk blade holders and LS2 skate blades. Subjects completed a battery of eight on-ice skating drills used to measure and compare two aspects of skating speed; acceleration [T1(s)] and total time to complete each drill [TT(s)] while skating on three skate blade conditions. The drills represented skills used in the game of hockey, both in isolation (e.g., forward skating, backward skating, stops and starts, and cornering) and in sequence to simulate the combination of skills used in a shift of game play. The three blade conditions consisted of (i) baseline, represented by the blades worn by the player throughout their current season of play; (ii) experimental blades (EB), represented by brand name experimental blades with manufacturers radius of contour and a standardized radius of hollow; and (iii) customized experimental blades (CEB), represented by the same brand name experimental blades sharpened to the players’ preference as identified in the baseline condition. No significant differences were found in acceleration time [T1(s)] or total time to complete [TT(s)] the isolated drills across blade conditions; however significant differences were revealed in both T1(s) and TT(s) measured during the execution of the sequenced drill across blade conditions. A iii Bonferroni post hoc test revealed that players skated significantly faster when skating on the CEB condition compared to the baseline condition (p≤.05). A questionnaire assessing subjects perceived comfort, confidence and effort expended while skating on the experimental blades revealed that players were significantly more comfortable when skating on the CEB versus the EB condition (p≤.05). Outcomes of the study provide evidence to suggest that the experimental skate blades customized with the players preferred blade sharpening characteristics results in faster skating speed in a combination drill representing skills performed in gameplay.

Synthesis of new zirconium complexes

L'étude suivante décrit la synthèse des ligands nacnacxylH, nacnacBnH, nacnacR,RH et nacnacCyH en utilisant une méthode générale qui implique des rendements élevés et des coûts raisonnables, la complexation de ces ligands au Zr, la caractérisation de ces complexes et l’investigation de leurs réactivités. Les complexes de zirconium ont été obtenus en utilisant deux méthodes synthétiques principales : la première consiste en traitement du sel de lithium du ligand avec le ZrCl4. La seconde est la réaction du ligand neutre avec les complexes d’alkyl-zirconium(IV) par protonation de l'alkyle coordonné. Le ligand adopte deux modes de coordination avec le Zr. Une coordination 2 est observée dans les complexes octaèdriques contenant un ou deux ligands nacnac. En présence d'un autre ligand ayant une coordonnation 5, par exemple Cp ou Ind, le ligand nacnac se trouve en coordination x avec le centre métallique de zirconium. En solution, les complexes obtenus de (nacnac)2ZrX2 montrent un comportement dynamique via un « Bailar-twist » et les paramètres d'activation de cette isomérisation ont été obtenus. Le complexe octaèdrique (nacnacBn)2ZrCl2, 2c, n'a pas montré de réactivité dans la carbozirconation et son alkylation n'était pas possible par l’échange des chlorures avec les alkyles. L’analogue dimethylé (nacnacBn)2ZrMe2, 2d, peut être préparé par alkylation du ZrCl4 avant la complexation du ligand. Ce dernier a été prouvé aussi de ne pas être réactif dans la carbozirconation.

RNA recurrent motifs : identification and characterization

La détermination de la structure tertiaire du ribosome fut une étape importante dans la compréhension du mécanisme de la synthèse des protéines. Par contre, l’élucidation de la structure du ribosome comme tel ne permet pas une compréhension de sa fonction. Pour mieux comprendre la nature des relations entre la structure et la fonction du ribosome, sa structure doit être étudiée de manière systématique. Au cours des dernières années, nous avons entrepris une démarche systématique afin d’identifier et de caractériser de nouveaux motifs structuraux qui existent dans la structure du ribosome et d’autres molécules contenant de l’ARN. L’analyse de plusieurs exemples d’empaquetage de deux hélices d’ARN dans la structure du ribosome nous a permis d’identifier un nouveau motif structural, nommé « G-ribo ». Dans ce motif, l’interaction d’une guanosine dans une hélice avec le ribose d’un nucléotide d’une autre hélice donne naissance à un réseau d’interactions complexes entre les nucléotides voisins. Le motif G-ribo est retrouvé à 8 endroits dans la structure du ribosome. La structure du G-ribo possède certaines particularités qui lui permettent de favoriser la formation d’un certain type de pseudo-nœuds dans le ribosome. L’analyse systématique de la structure du ribosome et de la ARNase P a permis d’identifier un autre motif structural, nommé « DTJ » ou « Double-Twist Joint motif ». Ce motif est formé de trois courtes hélices qui s’empilent l’une sur l’autre. Dans la zone de contact entre chaque paire d’hélices, deux paires de bases consécutives sont surenroulées par rapport à deux paires de bases consécutives retrouvées dans l’ARN de forme A. Un nucléotide d’une paire de bases est toujours connecté directement à un nucléotide de la paire de bases surenroulée, tandis que les nucléotides opposés sont connectés par un ou plusieurs nucléotides non appariés. L’introduction d’un surenroulement entre deux paires de bases consécutives brise l’empilement entre les nucléotides et déstabilise l’hélice d’ARN. Dans le motif DTJ, les nucléotides non appariés qui lient les deux paires de bases surenroulées interagissent avec une des trois hélices qui forment le motif, offrant ainsi une stratégie élégante de stabilisation de l’arrangement. Pour déterminer les contraintes de séquences imposées sur la structure tertiaire d’un motif récurrent dans le ribosome, nous avons développé une nouvelle approche expérimentale. Nous avons introduit des librairies combinatoires de certains nucléotides retrouvés dans des motifs particuliers du ribosome. Suite à l’analyse des séquences alternatives sélectionnées in vivo pour différents représentants d’un motif, nous avons été en mesure d’identifier les contraintes responsables de l’intégrité d’un motif et celles responsables d’interactions avec les éléments qui forment le contexte structural du motif. Les résultats présentés dans cette thèse élargissent considérablement notre compréhension des principes de formation de la structure d’ARN et apportent une nouvelle façon d’identifier et de caractériser de nouveaux motifs structuraux d’ARN.

Quelques propriétés des sous-variétés lagrangiennes monotones : Rayon de Gromov et morphisme de Seidel

Cette thèse présente quelques propriétés des sous-variétés lagrangiennes monotones. On résoud d'abord une conjecture de Barraud et Cornea dans le cadre monotone en montrant que le rayon de Gromov relatif à deux lagrangiennes dans la même classe d'isotopie hamiltonienne donne une borne inférieure à la distance de Hofer entre ces deux mêmes lagrangiennes. Le cas non-monotone de cette conjecture reste ouvert encore. On définit toutes les structures nécessaires à l'énoncé et à la preuve de cette conjecture. Deuxièmement, on définit une nouvelle version d'un morphisme de Seidel relatif à l'aide des cobordismes lagrangiens de Biran et Cornea. On montre que cette version est chaîne-homotope aux différentes autres versions apparaissant dans la littérature. Que toutes ces définitions sont équivalentes fait partie du folklore mais n'apparaît pas dans la littérature. On conclut par une conjecture qui identifie un triangle exact obtenu par chirurgie lagrangienne et un autre dû à Seidel et faisant intervenir le twist de Dehn symplectique.

Développement et validation d'un modèle de simulation numérique personnalisé à une athlète de plongeon

Les entraîneurs en sports acrobatiques disposent de peu d’outils permettant d’améliorer leur compréhension des saltos vrillés et la performance des athlètes. L’objectif de ce mémoire était de développer un environnement graphique de simulation numérique réaliste et utile des acrobaties aériennes. Un modèle composé de 17 segments et de 42 degrés de liberté a été développé et personnalisé à une athlète de plongeon. Un système optoélectronique échantillonné à 300 Hz a permis l’acquisition de huit plongeons en situation réelle d’entraînement. La cinématique articulaire reconstruite avec un filtre de Kalman étendu a été utilisée comme entrée du modèle. Des erreurs quadratiques moyennes de 20° (salto) et de 9° (vrille) entre les performances simulées et réelles ont permis de valider le modèle. Enfin, une formation basée sur le simulateur a été offerte à 14 entraîneurs en sports acrobatiques. Une augmentation moyenne de 11 % des résultats aux questionnaires post-test a permis de constater le potentiel pédagogique de l’outil pour la formation.