Fate and transport of nursery-box-applied tricyclazole and imidacloprid in paddy fields

The fate and transport of tricyclazole and imidacloprid in paddy plots after nursery-box application was monitored. Water and surface soil samples were collected over a period of 35 days. Rates of dissipation from paddy waters and soils were also measured. Dissipation of the two pesticides from paddy water can be described by first-order kinetics. In the soil, only the dissipation of imidacloprid fitted to the simple first-order kinetics, whereas tricyclazole concentrations fluctuated until the end of the monitoring period. Mean half-life (DT₅₀) values for tricyclazole were 11.8 and 305 days, respectively, in paddy water and surface soil. The corresponding values of imidacloprid were 2.0 and 12.5 days, respectively, in water and in surface soil. Less than 0.9% of tricyclazole and 0.1% of imidacloprid were lost through runoff during the monitoring period even under 6.3 cm of rainfall. The pesticide formulation seemed to affect the environmental fate of these pesticides when these results were compared to those of other studies.

Piggery pond sludge as a nitrogen source for crops. 1. Mineral N supply estimated from laboratory incubations and field application of stockpiled and wet sludge

Piggery pond sludge (PPS) was applied, as-collected (Wet PPS) and following stockpiling for 12 months (Stockpiled PPS), to a sandy Sodosol and clay Vertosol at sites on the Darling Downs of Queensland. Laboratory measures of N availability were carried out on unamended and PPS-amended soils to investigate their value in estimating supplementary N needs of crops in Australia's northern grains region. Cumulative net N mineralised from the long-term (30 weeks) leached aerobic incubation was described by a first-order single exponential model. The mineralisation rate constant (0.057/week) was not significantly different between Control and PPS treatments or across soil types, when the amounts of initial mineral N applied in PPS treatments were excluded. Potentially mineralisable N (No) was significantly increased by the application of Wet PPS, and increased with increasing rate of application. Application of Wet PPS significantly increased the total amount of inorganic N leached compared with the Control treatments. Mineral N applied in Wet PPS contributed as much to the total mineral N status of the soil as did that which mineralised over time from organic N. Rates of C02 evolution during 30 weeks of aerobic leached incubation indicated that the Stockpiled PPS was more stabilised (19-28% of applied organic C mineralised) than the WetPPS (35-58% of applied organic C mineralised), due to higher lignin content in the former. Net nitrate-N produced following 12 weeks of aerobic non-leached incubation was highly correlated with net nitrate-N leached during 12 weeks of aerobic incubation (R^2 = 0.96), although it was <60% of the latter in both sandy and clayey soils. Anaerobically mineralisable N determined by waterlogged incubation of laboratory PPS-amended soil samples increased with increasing application rate of Wet PPS. Anaerobically minemlisable N from field-moist soil was well correlated with net N mineralised during 30 weeks of aerobic leached incubation (R^2 =0.90 sandy soil; R^2=0.93 clay soil). In the clay soil, the amount of mineral N produced from all the laboratory incubations was significantly correlated with field-measured nitrate-N in the soil profile (0-1.5 m depth) after 9 months of weed-free fallow following PPS application. In contrast, only anaerobic mineralisable N was significantly correlated with field nitrate-N in the sandy soil. Anaerobic incubation would, therefore, be suitable as a rapid practical test to estimate potentially mineralisable N following applications of different PPS materials in the field.

Development of a stable isotope index to assess decadal-scale vegetation change and application to woodlands of the Burdekin catchment, Australia

Forty-four study sites were established in remnant woodland in the Burdekin River catchment in tropical north-east Queensland, Australia, to assess recent (decadal) vegetation change. The aim of this study was further to evaluate whether wide-scale vegetation 'thickening' (proliferation of woody plants in formerly more open woodlands) had occurred during the last century, coinciding with significant changes in land management. Soil samples from several depth intervals were size separated into different soil organic carbon (SOC) fractions, which differed from one another by chemical composition and turnover times. Tropical (C4) grasses dominate in the Burdekin catchment, and thus δ13C analyses of SOC fractions with different turnover times can be used to assess whether the relative proportion of trees (C3) and grasses (C4) had changed over time. However, a method was required to permit standardized assessment of the δ13C data for the individual sites within the 13 Mha catchment, which varied in soil and vegetation characteristics. Thus, an index was developed using data from three detailed study sites and global literature to standardize individual isotopic data from different soil depths and SOC fractions to reflect only the changed proportion of trees (C3) to grasses (C3) over decadal timescales. When applied to the 44 individual sites distributed throughout the Burdekin catchment, 64% of the sites were shown to have experienced decadal vegetation thickening, while 29% had remained stable and the remaining 7% had thinned. Thus, the development of this index enabled regional scale assessment and comparison of decadal vegetation patterns without having to rely on prior knowledge of vegetation changes or aerial photography.

First record of stubby-root nematode (Paratrichodorus porosus) associated with barley in Australia

High populations (5000 to 20 000/kg soil) of the stubby-root nematode Paratrichodorus porosus were identified morphologically from soil samples taken under patches of poorly growing barley in a field between Yuleba and Surat in western Queensland, Australia. Lower populations (<4000/kg soil) were recovered from soil samples taken from asymptomatic barley. This is the first record of this nematode species on barley in Australia.

Fungal community structure in disease suppressive soils assessed by 28S LSU gene sequencing

Natural biological suppression of soil-borne diseases is a function of the activity and composition of soil microbial communities. Soil microbe and phytopathogen interactions can occur prior to crop sowing and/or in the rhizosphere, subsequently influencing both plant growth and productivity. Research on suppressive microbial communities has concentrated on bacteria although fungi can also influence soil-borne disease. Fungi were analyzed in co-located soils 'suppressive' or 'non-suppressive' for disease caused by Rhizoctonia solani AG 8 at two sites in South Australia using 454 pyrosequencing targeting the fungal 28S LSU rRNA gene. DNA was extracted from a minimum of 125 g of soil per replicate to reduce the micro-scale community variability, and from soil samples taken at sowing and from the rhizosphere at 7 weeks to cover the peak Rhizoctonia infection period. A total of ∼994,000 reads were classified into 917 genera covering 54% of the RDP Fungal Classifier database, a high diversity for an alkaline, low organic matter soil. Statistical analyses and community ordinations revealed significant differences in fungal community composition between suppressive and non-suppressive soil and between soil type/location. The majority of differences associated with suppressive soils were attributed to less than 40 genera including a number of endophytic species with plant pathogen suppression potentials and mycoparasites such as Xylaria spp. Non-suppressive soils were dominated by Alternaria , Gibberella and Penicillum. Pyrosequencing generated a detailed description of fungal community structure and identified candidate taxa that may influence pathogen-plant interactions in stable disease suppression. © 2014 Penton et al.

Potential Animal and Environmental Sources of Q Fever Infection for Humans in Queensland

Q fever is a vaccine-preventable disease; despite this, high annual notification numbers are still recorded in Australia. We have previously shown seroprevalence in Queensland metropolitan regions is approaching that of rural areas. This study investigated the presence of nucleic acid from Coxiella burnetii, the agent responsible for Q fever, in a number of animal and environmental samples collected throughout Queensland, to identify potential sources of human infection. Samples were collected from 129 geographical locations and included urine, faeces and whole blood from 22 different animal species; 45 ticks were removed from two species, canines and possums; 151 soil samples; 72 atmospheric dust samples collected from two locations and 50 dust swabs collected from domestic vacuum cleaners. PCR testing was performed targeting the IS1111 and COM1 genes for the specific detection of C.burnetii DNA. There were 85 detections from 1318 animal samples, giving a detection rate for each sample type ranging from 2.1 to 6.8%. Equine samples produced a detection rate of 11.9%, whilst feline and canine samples showed detection rates of 7.8% and 5.2%, respectively. Native animals had varying detection rates: pooled urines from flying foxes had 7.8%, whilst koalas had 5.1%, and 6.7% of ticks screened were positive. The soil and dust samples showed the presence of C.burnetii DNA ranging from 2.0 to 6.9%, respectively. These data show that specimens from a variety of animal species and the general environment provide a number of potential sources for C.burnetii infections of humans living in Queensland. These previously unrecognized sources may account for the high seroprevalence rates seen in putative low-risk communities, including Q fever patients with no direct animal contact and those subjects living in a low-risk urban environment.

Development of analytical techniques for studies on dispersion of actinides in the environment and characterization of environmental radioactive particles

Radioactive particles from three locations were investigated for elemental composition, oxidation states of matrix elements, and origin. Instrumental techniques applied to the task were scanning electron microscopy, X-ray and gamma-ray spectrometry, secondary ion mass spectrometry, and synchrotron radiation based microanalytical techniques comprising X-ray fluorescence spectrometry, X-ray fluorescence tomography, and X-ray absorption near-edge structure spectroscopy. Uranium-containing low activity particles collected from Irish Sea sediments were characterized in terms of composition and distribution of matrix elements and the oxidation states of uranium. Indications of the origin were obtained from the intensity ratios and the presence of thorium, uranium, and plutonium. Uranium in the particles was found to exist mostly as U(IV). Studies on plutonium particles from Runit Island (Marshall Islands) soil indicated that the samples were weapon fuel fragments originating from two separate detonations: a safety test and a low-yield test. The plutonium in the particles was found to be of similar age. The distribution and oxidation states of uranium and plutonium in the matrix of weapon fuel particles from Thule (Greenland) sediments were investigated. The variations in intensity ratios observed with different techniques indicated more than one origin. Uranium in particle matrixes was mostly U(IV), but plutonium existed in some particles mainly as Pu(IV), and in others mainly as oxidized Pu(VI). The results demonstrated that the various techniques were effectively applied in the characterization of environmental radioactive particles. An on-line method was developed for separating americium from environmental samples. The procedure utilizes extraction chromatography to separate americium from light lanthanides, and cation exchange to concentrate americium before the final separation in an ion chromatography column. The separated radiochemically pure americium fraction is measured by alpha spectrometry. The method was tested with certified sediment and soil samples and found to be applicable for the analysis of environmental samples containing a wide range of Am-241 activity. Proceeding from the on-line method developed for americium, a method was also developed for separating plutonium and americium. Plutonium is reduced to Pu(III), and separated together with Am(III) throughout the procedure. Pu(III) and Am(III) are eluted from the ion chromatography column as anionic dipicolinate and oxalate complexes, respectively, and measured by alpha spectrometry.

A method for the preferential isolation of actinomycetes from soils

A successful plate-method for the preferential isolation of actinomycetes from soils is described. The principles underlying it are: (1) the inhibition of growth of non-sporulating bacteria by pre-incubation at a high temperature (110 C) for 10 min, and (2) limiting the spreading growth of sporeforming bacteria and fungi by the use of dried plates. The majority of the 191 species isolated by this method from 82 soil samples were shown to be pectinolytic.

Relationship between Low Strain Shear Modulus and Standard Penetration Test N Values

A low strain shear modulus plays a fundamental role in the estimation of site response parameters In this study an attempt has been made to develop the relationships between standard penetration test (SPT) N values with the low strain shear modulus (G(max)) For this purpose, field experiments SPT and multichannel analysis of surface wave data from 38 locations in Bangalore, India, have been used, which were also used for seismic microzonation project The in situ density of soil layer was evaluated using undisturbed soil samples from the boreholes Shear wave velocity (V-s) profiles with depth were obtained for the same locations or close to the boreholes The values for low strain shear modulus have been calculated using measured V-s and soil density About 215 pairs of SPT N and G(max) values are used for regression analysis The differences between fitted regression relations using measured and corrected values were analyzed It is found that an uncorrected value of N and modulus gives the best fit with a high regression coefficient when compared to corrected N and corrected modulus values This study shows better correlation between measured values of N and G(max) when compared to overburden stress corrected values of N and G(max)

Microbiological characterisation of soils : Evaluation of some critical steps in data collection and experimental design

The study of soil microbiota and their activities is central to the understanding of many ecosystem processes such as decomposition and nutrient cycling. The collection of microbiological data from soils generally involves several sequential steps of sampling, pretreatment and laboratory measurements. The reliability of results is dependent on reliable methods in every step. The aim of this thesis was to critically evaluate some central methods and procedures used in soil microbiological studies in order to increase our understanding of the factors that affect the measurement results and to provide guidance and new approaches for the design of experiments. The thesis focuses on four major themes: 1) soil microbiological heterogeneity and sampling, 2) storage of soil samples, 3) DNA extraction from soil, and 4) quantification of specific microbial groups by the most-probable-number (MPN) procedure. Soil heterogeneity and sampling are discussed as a single theme because knowledge on spatial (horizontal and vertical) and temporal variation is crucial when designing sampling procedures. Comparison of adjacent forest, meadow and cropped field plots showed that land use has a strong impact on the degree of horizontal variation of soil enzyme activities and bacterial community structure. However, regardless of the land use, the variation of microbiological characteristics appeared not to have predictable spatial structure at 0.5-10 m. Temporal and soil depth-related patterns were studied in relation to plant growth in cropped soil. The results showed that most enzyme activities and microbial biomass have a clear decreasing trend in the top 40 cm soil profile and a temporal pattern during the growing season. A new procedure for sampling of soil microbiological characteristics based on stratified sampling and pre-characterisation of samples was developed. A practical example demonstrated the potential of the new procedure to reduce the analysis efforts involved in laborious microbiological measurements without loss of precision. The investigation of storage of soil samples revealed that freezing (-20 °C) of small sample aliquots retains the activity of hydrolytic enzymes and the structure of the bacterial community in different soil matrices relatively well whereas air-drying cannot be recommended as a storage method for soil microbiological properties due to large reductions in activity. Freezing below -70 °C was the preferred method of storage for samples with high organic matter content. Comparison of different direct DNA extraction methods showed that the cell lysis treatment has a strong impact on the molecular size of DNA obtained and on the bacterial community structure detected. An improved MPN method for the enumeration of soil naphthalene degraders was introduced as an alternative to more complex MPN protocols or the DNA-based quantification approach. The main advantage of the new method is the simple protocol and the possibility to analyse a large number of samples and replicates simultaneously.

Identification of source of heavy metal contamination in a site - a case study

Accidental spills and improper disposal of industrial effluent/sludge containing heavy metals onto the open land or into subsurface result in soil and water contamination. Detailed investigations are carried out to identify the source of contamination of heavy metals in an industrial suburb near Bangalore in India. Detailed investigation of ground water and subsurface soil analysis for various heavy metals has been carried out. Ground water samples were collected in the entire area through the cluster of borewells. Subsurface soil samples were collected from near borewells which were found to contain heavy metals. Water samples and soils samples (after acid digestion) were analysed as per APHO-standard method of analysis. While the results of Zn, Ni and Cd showed that they are within allowable limits in the soil, the ground water and soils in the site have concentration of Cr+6 far exceeding the allowable limits (up to 832 mg/kg). Considering the topography of the area, ground water movement and results of chromium concentration in the borewells and subsurface it was possible to identify the origin, zone of contamination and the migration path of Cr+6. The results indicated that the predominant mechanism of migration of Cr+6 is by diffusion.

The Effects of Grain Size Distribution and Structure on Mechanical Behavior of Silt

Abstract: In order to investigate the effects of the grain size distribution and the micro-structure of soils on the mechani- cal characteristics, some static triaxial compression tests were carried out, and then the relationship of stress-strain and the strength behavior of silty sand were compared among undisturbed samples with different grain size distribution, undis- turbed and remolded samples with the same grain size distribution, and reconstituted samples (or called mixed samples) with different grain size distribution. The effects of grain size distribution and structure on the mechanic behavior of silty sands were mainly analyzed. It is shown that the obvious differences of the mechanical characteristics between undis- turbed soils and remolded soils are caused by the differences of soil structures. Although the grain size distribution are different between two soil samples, their mechanical characteristics may be close to each other, or may have obvious differences because of the effects of micro-structure.

Avaliação dos teores de resíduos do pesticida ditiocarbamato no solo de uma cultura de couve (Brassica Oleracea L.) utilizando cloridrato de L-cisteina para preservação das amostras

Os pesticidas etileno-bis-ditiocarbamatos da classe dos ditiocarbamatos estão entre os fungicidas mais empregados em todo o mundo para o controle de pragas. Muitos métodos para determinar ditiocarbamatos são baseados na hidrólise ácida em presença de cloreto estanoso e análise do CS2 gerado por diferentes técnicas. Nesse contexto, constituiram em objetivos do presente trabalho, como primeira etapa, o estudo de condições adequadas à estocagem de amostras de solo, e como segunda etapa, a avaliação das taxas de degradação e de lixiviação do fungicida mancozebe num cambissolo distrófico através do método espectrofotométrico. O sítio de estudo foi uma área delimitada de 36 m2, de uma cultura de couve, localizada em São Lourenço no 3 distrito do município de Nova Friburgo-RJ. As análises foram realizadas no laboratório de tecnologia ambiental (LABTAM/UERJ). Na primeira etapa, duas sub-amostras de solo contaminadas com mancozebe foram submetidas a tratamento com cloridrato de L-cisteina e estocadas às temperaturas ambiente e de -20C, sendo posteriormente analisadas em intervalos de 1, 7, 15 e 35 dias após a aplicação do fungicida. Outras duas sub-amostras não tratadas com cloridrato de L-cisteina foram submetidas às mesmas condições de temperatura e analisadas nos mesmos intervalos de tempo. Na segunda etapa, foi efetuada a aplicação do fungicida MANZATE 800 (Dupont Brasil, 80% mancozebe) na dose recomendada de 3,0 Kg ha-1 e coletadas amostras do solo nas profundidades de 0-10, 10-20 e 20-40 cm em intervalos de 2,5,8,12,15,18 e 35 dias após aplicação. As amostras de cada profundidade foram tratadas com cloridrato de L-cisteina e acondicionadas sob temperatura de -20C. Através dos resultados obtidos na primeira etapa, pôde-se concluir que o tratamento com cisteina foi eficaz para conservação do analito, tanto para a amostra mantida a -20C quanto para a amostra mantida à temperatura ambiente. Os dados obtidos na segunda etapa do estudo mostraram que mancozebe apresentou comportamento semelhante ao descrito na literatura, para persistência no solo. Os resultados de lixiviação mostraram que nas condições pelas quais foi conduzido o experimento, resíduos de mancozebe foram detectados em profundidades de até 40 cm, porém através dos modelos de potencial de lixiviação, concluiu-se que o fungicida não oferece risco de contaminação de águas subterrâneas

Monitoramento do agrotóxico mancozeb no solo em diferentes sistemas de plantios de tomate

O presente trabalho tem por objetivo monitorar o agrotóxico Mancozeb no solo em diferentes sistemas de plantios de tomate utilizando a metodologia de decomposição dos ditiocarbamatos (DTCs) com geração de dissulfeto de carbono (CS2). Este método é amplamente utilizado na determinação dos resíduos de DTCs em alimentos, tendo sido adaptado para trabalhar com amostras de solo artificiais e reais. O método foi avaliado utilizando amostras contaminadas artificialmente a partir de uma amostra de solo controle, proveniente da Amazônia. A contaminação foi realizada com uma solução de campo (2 g.L-1 em água) do agrotóxico Manzate 800 (Mancozeb). A partir do momento em que foram determinadas as condições ideais de operação do método de decomposição dos DTCs, analisou-se o teor de Mancozeb em amostras reais, provenientes de uma área cultivada com tomate, no Município de São José de Ubá (RJ), sob sistemas de Plantios Convencional, Mínimo e Direto. Foi possível constatar a presença de teores de Mancozeb nas amostras reais de solo em estudo, coletadas nas profundidades 0 - 5 cm; 5 - 10 cm; 10 - 20 cm e 20 - 40 cm. Os resultados mostraram que os solos provenientes dos sistemas convencional e mínimo apresentaram, na camada superficial, um teor de Mancozeb de (7,44 mg.kg-1 e 5,70 mg.kg-1) superior ao obtido no sistema direto, que apresentou teores de (1,14 mg.kg-1 e 1,95 mg.kg-1) de Mancozeb

Verificação do desempenho do ensaio de adensamento CRS comparado ao SIC.

A presente dissertação objetiva a verificação do desempenho dos ensaios do tipo CRS, com velocidade controlada, quando comparados aos ensaios de adensamento oedométricos convencionais, SIC. O ensaio SIC é executado em vários estágios de carga, cada qual com vinte e quatro horas de duração e razão unitária entre o incremento de tensão e a tensão anterior, requerendo um prazo total de cerca de 10 dias para sua execução. Já o ensaio de adensamento com velocidade controlada, CRS, tem sua duração bastante reduzida, o que levou diversos pesquisadores da área de Geotecnia a concentrarem esforços no estudo de seu desempenho, visando sua utilização mais ampla. Para este estudo foi adquirido equipamento da empresa Hogentogler Inc., designado por GeoStar. Sua instalação, montagem e calibração foram realizadas no Laboratório de Mecânica dos Solos. Foram executados ensaios em corpos de prova obtidos de amostras de caulim, preparadas em laboratório, e também em amostras de solos originários de dois depósitos de diferentes regiões no Estado do Rio de Janeiro: baixada de Jacarepaguá e Itaboraí. A dissertação procurou detalhar a execução dos ensaios, as dificuldades da interpretação das planilhas originadas pelo sistema de aquisição de dados, acoplado ao equipamento GeoStar, as mudanças efetuadas, as ocorrências não previstas, a análise e interpretação dos resultados e a comparação dos parâmetros obtidos com os ensaios SIC e CRS. Procurou-se estudar o efeito da velocidade de deformação, histórico de tensões, qualidade dos corpos de prova, parâmetros do ensaio, facilidade de execução e desempenho. Verificou-se a simplicidade, rapidez e o desempenho satisfatório do ensaio CRS. Sugere-se estender estudos semelhantes a outros locais e, principalmente, a amostras de qualidade superior, na expectativa de confirmar as conclusões detalhadas nesta pesquisa.