Determination of carrier mobility in MEH-PPV thin-films by stationary and transient current techniques

Charge transport and shelf-degradation of MEH-PPV thin-films were investigated through stationary (e.g. current versus voltage - JxV) and transient (e.g. Time-of-Flight - ToF, Dark-Injection Space-Charge-Limited Current - DI-SCLC, Charge Extraction by Linearly Increasing Voltage - CELN) current techniques. Charge carrier mobility in nanometric films was best characterized through JxV and DI-SCLC. It approaches 10(-6) cm(2)Ns under a SCLC regime with deep traps for light-emitting diode applications. ToF measurements performed on micrometric layers (i.e. - 3 mu m) confirmed studies in 100 nm-thick films as deposited in OLEDs. All results were comparable to a similar poly(para-phenylene vinylene) derivative, MDMO-PPV. Electrical properties extracted from thin-film transistors demonstrated mobility dependence on carrier concentration in the channel (similar to 10(-7)-10(-4) cm(2)/Vs). At low accumulated charge levels and reduced free carrier concentration, a perfect agreement to the previously cited techniques was observed. Degradation was verified through mobility reduction and changes in trap distribution of states. (C) 2011 Elsevier B.V. All rights reserved.

Dental Pulp Vascular Permeability Changes Induced by Dental Bleaching

Aiming to compare the effect of different light sources for dental bleaching on vascular permeability of dental pulps, forty-eight incisors were used. The bleaching agent (35% hydrogen peroxide) was activated by halogen light; LED (Light Emitting Diode) or LED, followed by laser phototherapy (LPT) (lambda = 780 nm; 3 J/cm(2)). After the bleaching procedures, the animals received an intra-arterial dye injection and one hour later were sacrificed. The teeth were diaphanized and photographed. The amount of blue stain content of each dental pulp was quantified using a computer imaging program. The data was statistically compared (p <= 0.05). The results showed a significant higher (p <= 0.01) dye content in the groups bleached with halogen light, compared with the control, LED and LED plus LPT groups. Thus, tooth bleaching activated by LED or LED plus LPT induces lesser resulted in increased vascular permeability than halogen light.

A LED Based Photometer for Solid Phase Photometry: Zinc Determination in Pharmaceutical Preparation Employing a Multicommuted Flow Analysis Approach

In this work, a LED (light emitting diode) based photometer for solid phase photometry is described. The photometer was designed to permit direct coupling of a light source (LED) and a photodiode to a flow cell with an optical pathlength of 4 mm. The flow cell was filled with adsorbing solid phase material (C-18), which was used to immobilize the chromogenic reagent 1-(2-thiazolylazo)-2-naphthol (TAN). Aiming to allow accuracy assessment, samples were also analyzed employing ICP OES (inductively coupled plasma optical emission spectrometry) methodology. Applying the paired t-test at the 95% confidence level, no significant difference was observed. Other useful features were also achieved: linear response ranging from 0.05 to 0.85 mg L-1 Zn, limit of detection of 9 mu g L-1 Zn (3 sigma criterion), standard deviation of 1.4% (n = 10), sampling throughput of 36 determinations per h, and a waste generation and reagent consumption of 1.7 mL and of 0.03 mu g per determination, respectively.

Comparison of Photodynamic Therapy versus conventional antifungal therapy for the treatment of denture stomatitis: a randomized clinical trial

Clin Microbiol Infect 2012; 18: E380E388 Abstract In this randomized clinical trial, the clinical and mycological efficacy of Photodynamic Therapy (PDT) was compared with that of topical antifungal therapy for the treatment of denture stomatitis (DS) and the prevalence of Candida species was identified. Patients were randomly assigned to one of two groups (n = 20 each); in the nystatin (NYT) group patients received topical treatment with nystatin (100 000 IU) four times daily for 15 days and in the PDT group the denture and palate of patients were sprayed with 500 mg/L of Photogem (R), and after 30 min of incubation, were illuminated by light emitting-diode light at 455 nm (37.5 and 122 J/cm2, respectively) three times a week for 15 days. Mycological cultures taken from dentures and palates and standard photographs of the palates were taken at baseline (day 0), at the end of the treatment (day 15) and at the follow-up time intervals (days 30, 60 and 90). Colonies were quantified (CFU/mL) and identified by biochemical tests. Data were analysed by Fishers exact test, analysis of variance and Tukey tests and ? test (a = 0.05). Both treatments significantly reduced the CFU/mL at the end of the treatments and on day 30 of the follow-up period (p <0.05). The NYT and PDT groups showed clinical success rates of 53% and 45%, respectively. Candida albicans was the most prevalent species identified. PDT was as effective as topical nystatin in the treatment of DS.

Dental pulp vascular permeability changes induced by dental bleaching

Aiming to compare the effect of different light sources for dental bleaching on vascular permeability of dental pulps, forty-eight incisors were used. The bleaching agent (35 % hydrogen peroxide) was activated by halogen light; LED (Light Emitting Diode) or LED, followed by laser phototherapy (LPT) (λ = 780 nm; 3 J/cm²). After the bleaching procedures, the animals received an intra-arterial dye injection and one hour later were sacrificed. The teeth were diaphanized and photographed. The amount of blue stain content of each dental pulp was quantified using a computer imaging program. The data was statistically compared (p < 0.05). The results showed a significant higher (p < 0.01) dye content in the groups bleached with halogen light, compared with the control, LED and LED plus LPT groups. Thus, tooth bleaching activated by LED or LED plus LPT induces lesser resulted in increased vascular permeability than halogen light.

Design and development of new green catalytic methodologies for the synthesis of enantiomerically enriched molecules

The following Ph.D work was mainly focused on catalysis, as a key technology, to achieve the objectives of sustainable (green) chemistry. After introducing the concepts of sustainable (green) chemistry and an assessment of new sustainable chemical technologies, the relationship between catalysis and sustainable (green) chemistry was briefly discussed and illustrated via an analysis of some selected and relevant examples. Afterwards, as a continuation of the ongoing interest in Dr. Marco Bandini’s group on organometallic and organocatalytic processes, I addressed my efforts to the design and development of novel catalytic green methodologies for the synthesis of enantiomerically enriched molecules. In the first two projects the attention was focused on the employment of solid supports to carry out reactions that still remain a prerogative of omogeneous catalysis. Firstly, particular emphasis was addressed to the discovery of catalytic enantioselective variants of nitroaldol condensation (commonly termed Henry reaction), using a complex consisting in a polyethylene supported diamino thiopene (DATx) ligands and copper as active species. In the second project, a new class of electrochemically modified surfaces with DATx palladium complexes was presented. The DATx-graphite system proved to be efficient in promoting the Suzuki reaction. Moreover, in collaboration with Prof. Wolf at the University of British Columbia (Vancouver), cyclic voltammetry studies were reported. This study disclosed new opportunities for carbon–carbon forming processes by using heterogeneous, electrodeposited catalyst films. A straightforward metal-free catalysis allowed the exploration around the world of organocatalysis. In fact, three different and novel methodologies, using Cinchona, Guanidine and Phosphine derivatives, were envisioned in the three following projects. An interesting variant of nitroaldol condensation with simple trifluoromethyl ketones and also their application in a non-conventional activation of indolyl cores by Friedel-Crafts-functionalization, led to two novel synthetic protocols. These approaches allowed the preparation of synthetically useful trifluoromethyl derivatives bearing quaternary stereocenters. Lastly, in the sixth project the first γ-alkylation of allenoates with conjugated carbonyl compounds was envisioned. In the last part of this Ph.D thesis bases on an extra-ordinary collaboration with Prof. Balzani and Prof. Gigli, I was involved in the synthesis and characterization of a new type of heteroleptic cyclometaled-Ir(III) complexes, bearing bis-oxazolines (BOXs) as ancillary ligands. The new heteroleptic complexes were fully characterized and in order to examine the electroluminescent properties of FIrBOX(CH2), an Organic Light Emitting Device was realized.

Electronic energy transfer processes and charge carrier transport in pi-conjugated polymers

Conjugated polymers have attracted tremendous academical and industrial research interest over the past decades due to the appealing advantages that organic / polymeric materials offer for electronic applications and devices such as organic light emitting diodes (OLED), organic field effect transistors (OFET), organic solar cells (OSC), photodiodes and plastic lasers. The optimization of organic materials for applications in optoelectronic devices requires detailed knowledge of their photophysical properties, for instance energy levels of excited singlet and triplet states, excited state decay mechanisms and charge carrier mobilities. In the present work a variety of different conjugated (co)polymers, mainly polyspirobifluorene- and polyfluorene-type materials, was investigated using time-resolved photoluminescence spectroscopy in the picosecond to second time domain to study their elementary photophysical properties and to get a deeper insight into structure-property relationships. The experiments cover fluorescence spectroscopy using Streak Camera techniques as well as time-delayed gated detection techniques for the investigation of delayed fluorescence and phosphorescence. All measurements were performed on the solid state, i.e. thin polymer films and on diluted solutions. Starting from the elementary photophysical properties of conjugated polymers the experiments were extended to studies of singlet and triplet energy transfer processes in polymer blends, polymer-triplet emitter blends and copolymers. The phenomenon of photonenergy upconversion was investigated in blue light-emitting polymer matrices doped with metallated porphyrin derivatives supposing an bimolecular annihilation upconversion mechanism which could be experimentally verified on a series of copolymers. This mechanism allows for more efficient photonenergy upconversion than previously reported for polyfluorene derivatives. In addition to the above described spectroscopical experiments, amplified spontaneous emission (ASE) in thin film polymer waveguides was studied employing a fully-arylated poly(indenofluorene) as the gain medium. It was found that the material exhibits a very low threshold value for amplification of blue light combined with an excellent oxidative stability, which makes it interesting as active material for organic solid state lasers. Apart from spectroscopical experiments, transient photocurrent measurements on conjugated polymers were performed as well to elucidate the charge carrier mobility in the solid state, which is an important material parameter for device applications. A modified time-of-flight (TOF) technique using a charge carrier generation layer allowed to study hole transport in a series of spirobifluorene copolymers to unravel the structure-mobility relationship by comparison with the homopolymer. Not only the charge carrier mobility could be determined for the series of polymers but also field- and temperature-dependent measurements analyzed in the framework of the Gaussian disorder model showed that results coincide very well with the predictions of the model. Thus, the validity of the disorder concept for charge carrier transport in amorphous glassy materials could be verified for the investigated series of copolymers.

Synthese und photophysikalische Eigenschaften von Indolocarbazolen und höheren Analoga

Das Ziel dieser Arbeit bestand zum einen in der Entwicklung einer einfachen Synthesestrategie zur Darstellung substituierter symmetrischer Indolo[3,2-b]carbazole sowie in der Erweiterung des -Elektronensystems, um höhere Analoga dieser Substanzklasse zu synthetisieren. Der Zugang sollte dabei durch eine doppelte Cadogan-Ringschlussreaktion als Schlüsselschritt erfolgen. Die doppelte Cadogan-Reaktion erfolgte dabei unter Mikrowellenbedingungen in zufriedenstellenden Ausbeuten. Mittels Röntgenstrukturanalyse sind die verschiedenen Indolo[3,2-b]carbazole und Diindolo[3,2-b;2´,3´-h]carbazole auf ihre Eigenschaften im Festkörper hin untersucht worden. Dabei zeigen sie mit ihren Anordnungen im festen Zustand gute Eigenschaften für deren Verwendung als organische Halbleitermaterialien in Organischen Dünnschichttransistoren oder auch in Organischen Leuchtdioden. Die photophysikalische Charakterisierung erfolgte mittels UV/Vis- und Fluoreszenzspektroskopie sowie durch elektrooptische Absorptionsmessung, die Informationen über die Größe der Dipolmomente im Grundzustand und im angeregten Franck-Condon-Zustand lieferte. Die elektrochemischen Eigenschaften wurden aus cyclovoltammetrischen Messungen durch die Bestimmung der Redoxpotentiale, und damit die Lage der HOMO- bzw. LUMO-Levels, gewonnen. Durch die Synthese und die Bestimmung ihrer photophysikalischen Eigenschaften, mittels UV/Vis- und Fluoreszenzspektroskopie, von auf Naphthalin basierenden Chromophoren wurden zudem Verbindungen dargestellt, die Verwendung in lumineszierenden Lanthanid(III)-Komplexen finden können. Die Darstellung erfolgte mittels einer palladium-katalysierten Arylaminierung gefolgt von einer Suzuki-Kupplung mit 1,4-Dibromnaphthalin als Startmaterial.

Studio delle proprieta ottiche ed elettriche di dispositivi led a confinamento quantico

In questa tesi viene descritto il funzionamento delle sorgenti di luce LED (Light Emitting Diode) a confinamento quantico, che rappresentano la nuova frontiera dell'illuminazione ad alta efficienza e durata. Nei capitoli introduttivi è descritta brevemente la storia dei LEDs dalla loro invenzione agli sviluppi più recenti. Il funzionamento di tali dispositivi fotonici è spiegato a partire dal concetto di sorgente di luce per elettroluminescenza, con particolare riferimento alle eterostrutture a confinamento quantico bidimensionale (quantum wells). I capitoli centrali riguardano i nitruri dei gruppi III-V, le cui caratteristiche e proprietà hanno permesso di fabbricare LEDs ad alta efficienza e ampio spettro di emissione, soprattutto in relazione al fatto che i LEDs a nitruri dei gruppi III-V emettono luce anche in presenza di alte densità di difetti estesi, nello specifico dislocazioni. I capitoli successivi sono dedicati alla presentazione del lavoro sperimentale svolto, che riguarda la caratterizzazione elettrica, ottica e strutturale di LEDs a confinamento quantico basati su nitruri del gruppo III-V GaN e InGaN, cresciuti nei laboratori di Cambridge dal Center for Gallium Nitride. Lo studio ha come obiettivo finale il confronto dei risultati ottenuti su LEDs con la medesima struttura epitassiale, ma differente densità di dislocazioni, allo scopo di comprendere meglio il ruolo che tali difetti estesi ricoprono nella determinazione dell'effcienza delle sorgenti di luce LED. L’ultimo capitolo riguarda la diffrazione a raggi X dal punto di vista teorico, con particolare attenzione ai metodi di valutazioni dello strain reticolare nei wafer a nitruri, dal quale dipende la densità di dislocazioni.

Studio di leds con diverse densita di dislocazioni tramite l'analisi del coefficiente di poole-frenkel

E' stato considerato un High-Dislocation Density Light Emitting Diode (HDD LED)ed è stato analizzato l'andamento di corrente a varie temperature. Dai risultati ottenuti è stato possibile ricavare il coefficiente di Poole-Frenkel, e da esso risalire alla densità di dislocazioni del dispositivo.

Übergangsmomente zwischen angeregten Zuständen mit der RI-CC2-Methode: Implementierung und Anwendung auf Triplett-Excimere

Die Themengebiete dieser Arbeit umfassen sowohl methodische Weiterentwicklungen im Rahmen der ab initio zweiter Ordnungsmethoden CC2 und ADC(2) als auch Anwendungen dieser Weiterentwick-lungen auf aktuelle Fragestellungen. Die methodischen Erweiterungen stehen dabei hauptsächlich im Zusammenhang mit Übergangsmomenten zwischen angeregten Zuständen. Durch die Implementie-rung der selbigen ist nun die Berechnung transienter Absorptionsspektren möglich. Die Anwendungen behandeln vorwiegend das Feld der organischen Halbleiter und deren photo-elektronische Eigen-schaften. Dabei spielen die bislang wenig erforschten Triplett-Excimere eine zentrale Rolle.rnDie Übergangsmomente zwischen angeregten Zuständen wurden in das Programmpaket TUR-BOMOLE implementiert. Dadurch wurde die Berechnung der Übergangsmomente zwischen Zustän-den gleicher Multiplizität (d.h. sowohl Singulett-Singulett- als auch Triplett-Triplett-Übergänge) und unterschiedlicher Multiplizität (also Singulett-Triplett-Übergänge) möglich. Als Erweiterung wurde durch ein Interface zum ORCA Programm die Berechnung von Spin-Orbit-Matrixelementen (SOMEs) implementiert. Des Weiteren kann man mit dieser Implementierung auch Übergänge in offenschaligen Systemen berechnen. Um den Speicherbedarf und die Rechenzeit möglichst gering zu halten wurde die resolution-of-the-identity (RI-) Näherung benutzt. Damit lässt sich der Speicherbedarf von O(N4) auf O(N3) reduzieren, da die mit O(N4) skalierenden Größen (z. B. die T2-Amplituden) sehr effizient aus RI-Intermediaten berechnet werden können und daher nicht abgespeichert werden müssen. Dadurch wird eine Berechnung für mittelgroße Moleküle (ca. 20-50 Atome) mit einer angemessenen Basis möglich.rnDie Genauigkeit der Übergangsmomente zwischen angeregten Zuständen wurde für einen Testsatz kleiner Moleküle sowie für ausgewählte größere organische Moleküle getestet. Dabei stellte sich her-aus, dass der Fehler der RI-Näherung sehr klein ist. Die Vorhersage der transienten Spektren mit CC2 bzw. ADC(2) birgt allerdings ein Problem, da diese Methoden solche Zustände nur sehr unzureichend beschreiben, welche hauptsächlich durch zweifach-Anregungen bezüglich der Referenzdeterminante erzeugt werden. Dies ist für die Spektren aus dem angeregten Zustand relevant, da Übergänge zu diesen Zuständen energetisch zugänglich und erlaubt sein können. Ein Beispiel dafür wird anhand eines Singulett-Singulett-Spektrums in der vorliegenden Arbeit diskutiert. Für die Übergänge zwischen Triplettzuständen ist dies allerdings weniger problematisch, da die energetisch niedrigsten Doppelan-regungen geschlossenschalig sind und daher für Tripletts nicht auftreten.rnVon besonderem Interesse für diese Arbeit ist die Bildung von Excimeren im angeregten Triplettzu-stand. Diese können aufgrund starker Wechselwirkungen zwischen den π-Elektronensystemen großer organischer Moleküle auftreten, wie sie zum Beispiel als organische Halbleiter in organischen Leucht-dioden eingesetzt werden. Dabei können die Excimere die photo-elktronischen Eigenschaften dieser Substanzen signifikant beeinflussen. Im Rahmen dieser Dissertation wurden daher zwei solcher Sys-teme untersucht, [3.3](4,4’)Biphenylophan und das Naphthalin-Dimer. Hierzu wurden die transienten Anregungsspektren aus dem ersten angeregten Triplettzustand berechnet und diese Ergebnisse für die Interpretation der experimentellen Spektren herangezogen. Aufgrund der guten Übereinstimmung zwischen den berechneten und den experimentellen Spektren konnte gezeigt werden, dass es für eine koplanare Anordnung der beiden Monomere zu einer starken Kopplung zwischen lokal angereg-ten und charge-transfer Zuständen kommt. Diese Kopplung resultiert in einer signifikanten energeti-schen Absenkung des ersten angeregten Zustandes und zu einem sehr geringen Abstand zwischen den Monomereinheiten. Dabei ist der angeregte Zustand über beide Monomere delokalisiert. Die star-ke Kopplung tritt bei einem intermolekularen Abstand ≤4 Å auf, was einem typischen Abstand in orga-nischen Halbleitern entspricht. In diesem Bereich kann man zur Berechnung dieser Systeme nicht auf die Förster-Dexter-Theorie zurückgreifen, da diese nur für den Grenzfall der schwachen Kopplung gültig ist.

Sintesi di complessi luminescenti anionici di Ir(III)

Negli ultimi anni si è osservato un crescente sviluppo della ricerca nel campo dei materiali luminescenti per le loro diverse applicazioni reali e potenziali, fra cui l’impiego in dispositivi elettroluminescenti, quali OLEDs (Organic Light-Emitting Diodes) e LECs (Light-Emitting Electrochemical Cells). In modo particolare, si rivolge grande attenzione ai complessi ciclometallati di Ir(III) grazie alle peculiari caratteristiche che li contraddistinguono fra i materiali luminescenti, come l'emissione fosforescente, alte rese quantiche di emissione, lunghi tempi di vita e buona stabilità nei dispositivi. Oltre a tali caratteristiche uno dei principali vantaggi presentati dai complessi di Ir(III) è la possibilità di modulare la lunghezza d'onda di emissione modificando la struttura dei leganti ciclometallanti e ancillari. Considerata la versatilità di questi sistemi e la loro conseguente rilevanza, diverse sono state le strategie applicate per l'ottenimento di complessi di Ir(III) generalmente neutri e cationici; al contrario pochi esempi di complessi di Ir(III) anionici sono attualmente riportati in letteratura. Lo scopo del mio lavoro di tesi è stato quindi quello di sintetizzare tre nuovi complessi anionici luminescenti di Ir(III) con tre diversi leganti ciclometallanti. Il piano di lavoro è stato suddiviso in stadi successivi, partendo dalla sintesi dei tre leganti ciclometallanti, impiegati poi nella preparazione dei dimeri di Ir(III) precursori dei miei complessi; infine facendo reagire questi ultimi con un legante ancillare bisanionico, derivato dal di(1H-tetrazol-5-il)metano, si è giunti all'ottenimento di tre complessi anionici luminescenti di Ir(III). Dopo questa prima parte, il lavoro di tesi è proseguito con la caratterizzazione spettroscopica dei tre complessi anionici e la determinazione delle loro proprietà fotofisiche tramite la registrazione di spettri di assorbimento, di emissione e la determinazione delle rese quantiche di emissione e dei tempi di vita. Infine si è preparato un “soft salt” costituito da un complesso anionico e uno cationico di Ir(III) le cui caratteristiche sono tutt'ora oggetto di studio del gruppo di ricerca presso il quale ho svolto il mio lavoro di tesi.

Halogen lamp and led activation of resin-modified glass ionomer restorative material. In vitro microhardness after long term storage

AIM: The purpose of this study was to evaluate the activation of resin-modified glass ionomer restorative material (RMGI, Vitremer-3M-ESPE, A3) by halogen lamp (QTH) or light-emitting diode (LED) by Knoop microhardness (KHN) in two storage conditions: 24hrs and 6 months and in two depths (0 and 2 mm). MATERIALS AND METHODS: The specimens were randomly divided into 3 experimental groups (n=10) according to activation form and evaluated in depth after 24h and after 6 months of storage. Activation was performed with QTH for 40s (700 mW/cm2) and for 40 or 20 s with LED (1,200 mW/scm2). After 24 hrs and 6 months of storage at 37°C in relative humidity in lightproof container, the Knoop microhardness test was performed. Statistics Data were analysed by three-way ANOVA and Tukey post-tests (p<0.05). RESULTS: All evaluated factors showed significant differences (p<0.05). After 24 hrs there were no differences within the experimental groups. KHN at 0 mm was significantly higher than 2 mm. After 6 months, there was an increase of microhardness values for all groups, being the ones activated by LED higher than the ones activated by QTH. CONCLUSION: Light-activation with LED positively influenced the KHN for RMGI evaluated after 6 months.

Formation of supramolecular polymers by chrysene oligomers

Supramolecular assembly of π-conjugated systems is of large interested due to the possibility to use them in electronic devices.[1] Chrysene is a polyaromatic hydrocarbon which has been studied e.g for organic light-emitting diodes (OLEDs).[2] In continuation of our previous work involving the supramolecular polymerisation of pyrene oligomers [3] an oligomer consisting of three chrysenes linked by phophodiesters was synthesised (Chry3). UV-Vis measurements show that aggregates of Chry3 are formed in aqueous medium. This is illustrated by general hypochromicity, a change in vibronic band intensities and, in particular, the appearance of a red-shifted absorption band in the S0 → S2 transition. The data suggest the formation of J-aggregates. The formation of supramolecular polymers is further studied by temperature-dependent absorption- and fluorescence measurements, and by atomic force microscopy (AFM).

Evaluation of the reliability of high concentrator GaAs solar cells by means of temperature accelerated aging tests

ABSTRACT Evaluating the reliability, warranty period, and power degradation of high concentration solar cells is crucial to introducing this new technology to the market. The reliability of high concentration GaAs solar cells, as measured in temperature accelerated life tests, is described in this paper. GaAs cells were tested under high thermal accelerated conditions that emulated operation under 700 or 1050 suns over a period exceeding 10 000 h. Progressive power degradation was observed, although no catastrophic failures occurred. An Arrhenius activation energy of 1.02 eV was determined from these tests. The solar cell reliability [R(t)] under working conditions of 65°C was evaluated for different failure limits (1–10% power loss). From this reliability function, the mean time to failure and the warranty time were evaluated. Solar cell temperature appeared to be the primary determinant of reliability and warranty period, with concentration being the secondary determinant. A 30-year warranty for these 1 mm2-sized GaAs cells (manufactured according to a light emitting diode-like approach) may be offered for both cell concentrations (700 and 1050 suns) if the solar cell is operated at a working temperature of 65°C.