Texture and mechanical properties evolution of a deep drawing medium carbon steel during cold rolling and subsequent recrystallization

Medium carbon steels are mostly used for simple applications; however, new applications have been developed for which good sheet metal formability is required. These types of steels have an inherent low formability. A medium-carbon hot-rolled SAE 1050 steel was selected for this study. It has been cold rolled with thickness reductions varying between 7 and 80%. The samples obtained were used to evaluate the strain hardening curve. For samples with a 50 and 80% thickness reduction, an annealing heat treatment was performed to achieve recrystallization. The material was characterized in the ""as-received"", cold rolled and annealed conditions using several methods: optical metallography, X-ray diffraction (texture), Vickers hardness, and tensile testing. For large thickness reductions, the SAE 1050 steel presented low elongation, less than 2%, and yield strength (YS) and tensile strength (TS) around 1400 MPa. Texture in the ""as-received"" condition showed strong components on the {001} plane, in the < 100 >, < 210 > and (110) directions. After cold rolling, the texture did not present any significant changes for small thickness reductions, however. It changed completely for large ones, where gamma, < 111 >//ND, alpha, < 110 > HRD, and gamma prime, < 223 >//ND, fibres were strengthened. After annealing, the microstructure of the SAE 1050 steel was characterized by recrystallized ferrite and globular cementite. There was little change in the alpha fibre for the 50% reduction, whereas for the 80% reduction, its intensity increased. Both gamma and gamma prime fibres vanished upon annealing for 50 and 80% reductions alike. (c) 2008 Elsevier B.V. All rights reserved.

Medium carbon steel deep drawing: A study on the evolution of mechanical properties, texture and simulations, from cold rolling to the end product

Medium carbon steels are mostly used for simple applications; nevertheless new applications have been developed for which good sheet formability is required. This class of steels has an inherent low formability. A medium carbon hot rolled SAE 1050 steel has been selected for this study. It has been cold rolled with reductions in the 7-80% range. Samples have been used to assess the cold work hardening curve. For samples with a 50 and 80% thickness reduction, an annealing heat treatment has been performed to obtain recrystallization. The material has been characterized in the ""as received"", cold rolled and annealed conditions, using several methods: optical microscopy, X-ray diffraction (texture), Vickers hardness and tensile testing. The 50% cold rolled and recrystallized material has been further studied in terms of sheet metal formability and texture evolution during the actual stamping of a steel toecap that has been used to validate the finite element simulations. (C) 2008 Elsevier B.V. All rights reserved.

Electrical and Mechanical Properties of Post-annealed SiC(x)N(y) Films

Amorphous SiC(x)N(y) films have been deposited on (100) Si substrates by RF magnetron sputtering of a SiC target in a variable nitrogen-argon atmosphere. The as-deposited films were submitted to thermal anneling in a furnace under argon atmosphere at 1000 degrees C for 1 hour. Composition and structure of unannealed and annealed samples were investigated by RBS and FTIR. To study the electrical characteristics of SiC(x)N(y) films, Metal-insulator-semiconductor (MIS) structures were fabricated. Elastic modulus and hardness of the films were determined by nanoindentation. The results of these studies showed that nitrogen content and thermal annealing affect the electrical, mechanical and structural properties of SiC(x)N(y) films.

Economic design of an X chart for short-run production

The aim of this paper is to present an economical design of an X chart for a short-run production. The process mean starts equal to mu(0) (in-control, State I) and in a random time it shifts to mu(1) > mu(0) (out-of-control, State II). The monitoring procedure consists of inspecting a single item at every m produced ones. If the measurement of the quality characteristic does not meet the control limits, the process is stopped, adjusted, and additional (r - 1) items are inspected retrospectively. The probabilistic model was developed considering only shifts in the process mean. A direct search technique is applied to find the optimum parameters which minimizes the expected cost function. Numerical examples illustrate the proposed procedure. (C) 2009 Elsevier B.V. All rights reserved.

CALCINED SLUDGE SINTERING EVALUATION BY HEATING MICROSCOPY THERMAL ANALYSIS

Aiming the use of the sewage sludge produced in one of the largest Brazilian wastewater treatment stations as a raw material for the ceramic industry, the sintering process of the ashes produced from its calcination was evaluated by heating microscopy thermal analysis (HMTA). From the microprocessed images, a method was developed to obtain HMTA dimensional change curves as a function of temperature, equivalent to those usually obtained from dilatometers or by thermomechanical analysis (TMA). The final product after sintering at 1050 degrees C, characterized by X-ray fluorescence spectrometry, scanning electron microscopy and X-ray dispersive energy, indicates the presence of a vitreous phase containing phosphorus, which explains the good sintering properties of the studied calcined sludge, as shown from its HMTA dimensional change curve.

Characterization of tree-rings of Pinus caribaea var. hondurensis Barr. et Golf. trees by X ray densitometry

This work aimed to determining the anatomical structure of wood, through methodology of histology and X-ray densitometry, of resin-tapped and not resin-tapped Pinus caribaea var. hondurensis trees samples, of three diameter classes. Pine trees, in forest plantation established in 1969, in the Ecological Experimental Station of Itirapina, from the Forestry Institute of Sao Paulo State, were measured and stratified into three classes of trunk diameter. The pine trees were resin-tapped since 2004, with the opening of two simultaneous and opposing panels. Sixty samples of pine wood trees were extracted from the tree trunk through a non-destructive method and in the laboratory. Tree rings were determined in the laboratory and wood apparent density by X-ray densitometry. The test results showed that: (i) false tree rings occur in the early wood and late wood of the tree rings due to climate change; (ii) the X-ray densitometry allowed the demarcation of the tree rings limits; (iii) the wood apparent density average was significantly different between the trees in high class diameter and in the medium-low class; (iv) the wood characteristics from the resin-tapped and non resin-tapped faces did not show significant differences.

Drip fungigation in early blight control of tomato

The aim was to verify if the fungigation via drip irrigation is an alternative to the conventional method of spraying on tomato for controlling early blight. Tomato plants (variety Santa Clara) were grown in pots inside a greenhouse. Fifty days after transplanting, the plants were inoculated with Alternaria solani and treated with four different fungicides: azoxystrobin (8 g 100 L(-1)), difeconazole (50 mL 100 L(-1)), metiram+piraclostrobin (200 g 100 L(-1)) and tebuconazole (100 mL 100 L(-1)) using two applications methods: conventional spraying and fiingigation dripping. The control plants did not receive fungicide application. To assess the severity of the disease, we used a rating scale expressed as the area under the disease progress curve (AUDPC) and production factors, such as number, weight and average diameter of the fruit and its productivity. The experimental design was completely randomized in factorial scheme 4 x 2 + 1 with eight replicates. Each plot had one plant in one pot. A 27% reduction in disease severity was observed when compared with the control plants, with no significant difference noted regarding the application method. The number of fruits did not statistically differ between the treatments. The average weight and diameter of the fruits were superior in the plants that had fungicide application compared to the control plant, reflecting an increase in productivity. Fungigation through water dripping is an alternative to the conventional method of spraying cultured tomatoes.

Progeny evaluation for resistance to Phaeosphaeria leaf spot in tropical maize

Maize breeding programmes in Brazil and elsewhere seek reliable methods to identify genotypes resistant to Phaeosphaeria leaf spot. The area under the disease progress curve (AUDPC) is an accurate method to evaluate the severity of foliar diseases. However, at least three data points are required to calculate the AUDPC, which is unfeasible when there are thousands of genotypes to be assessed. The aim of this work was to estimate the heritability of disease resistance, evaluate disease severity at different times using a nine-point scale in comparison to the AUDPC, and establish the most suitable phenological period for disease assessment. A repeated experiment was conducted in a 11 x 11 lattice experimental design with three replications. Disease assessments were carried out at flowering, 15 and 30 days post-anthesis for the parental lines DS95, DAS21, the F1 generation and 118 F2:3 progenies. Then, the AUDPC was obtained and results compared with the single-point evaluations used to calculate it. Individual and joint analyses of variance were conducted to obtain heritabiliy estimates. The assessments performed after the flowering stage gave higher estimates of heritability and correlation with AUDPC. We concluded that one assessment between the 15th and 30th day after flowering could provide enough information to distinguish maize genotypes for their resistance to Phaeosphaeria leaf spot under tropical conditions.

Preweaning performance and body composition of calves from straightbred Nellore and Bos taurus x Nellore crosses

The objectives were to evaluate preweaning performance, body composition, and efficiency of calves representing straightbred Nellore (NL), F(1), and 3-breed-cross systems. Energy requirements, milk production, and efficiency of 39 cow-calf pairs were recorded from straightbred NL calves from NL cows (10), crossbred (Angus-sired) calves from NL cows (ANL: 9), and crossbred calves (CC; Canchim-sired: 5/8 Charolais, 3/8 Zebu) from ANL (10) and Simmental x NL (10) cows. Cows and their respective calves were individually fed from birth to weaning (17 to 190 d postpartum). At 38 d of age, corn silage (7.8% CP, 2.19 Mcal of ME/kg of DM) was available to calves ad libitum. Milk production at 42, 98, 126, and 180 d postpartum was recorded by weighing calves before and after suckling. The ratio between GE and ME of milk was considered 1:0.93. Calves were slaughtered at weaning and the 9th-, 10th-, and 11th-rib section was removed for body composition estimation. The ANL calves were lighter (P < 0.01) at birth than the CC calves; the NL calves were intermediate. At weaning, the CC calves were heavier (P = 0.04) than the NL and ANL calves (230 +/- 5.5 vs. 172 +/- 8.1 and 209 +/- 8.6 kg, respectively). The ANL calves had greater (371 +/- 27 Mcal; P = 0.01) silage intake than the NL (270 +/- 25 Mcal) and CC (279 +/- 17 Mcal) calves. Milk energy intake was greater for the CC calves (970 +/- 38 Mcal of ME; P = 0.005) than the NL (670 +/- 57 Mcal of ME) and ANL (743 +/- 61 Mcal of ME) calves. The ANL calves compensated for the reduced milk production of the NL cows, which supplied less of their energy requirement for growth by increased silage intake. Calves from crossbred cows received a greater proportion of their total energy intake from milk. Crossbred calves had greater (P < 0.03) retained energy (retained energy = weaning body energy - birth body energy) than the NL calves (388 +/- 23 for ANL, and 438 +/- 15 for CC vs. 312 +/- 22 Mcal for NL calves). Percentages of water (P = 0.74) and chemical fat (P = 0.51) were similar among groups (63.7 +/- 0.6 and 14.3 +/- 0.7% for ANL calves, 63.1 +/- 0.4 and 14.7 +/- 0.5% for CC calves, and 63.3 +/- 0.6 and 13.7 +/- 0.7% of empty BW for water and chemical fat, respectively, for NL calves). Energetic efficiency (kcal of retained energy/Mcal of ME intake) was similar (P = 0.52) among groups (358 +/- 22 for ANL calves, 355 +/- 14 for CC calves, and 327 +/- 22 for NL calves). The greater BW gains and the differences in empty body composition at weaning were not enough to compensate for the greater ME intake of crossbreds. In this study, the crossbreeding systems evaluated increased preweaning calf performance but did not affect gross or energetic calf efficiency.

Cow/calf preweaning efficiency of Nellore and Bos taurus x Bos indicus crosses

The objectives of this study were to determine if percentage Bos taurus (0 or 50%) of the cow had an effect on ME requirements and milk production, and to compare cow/calf efficiency among 3 mating systems. Metabolizable energy requirements were estimated during a feeding trial that encompassed a gestation and lactation feeding trial for each of 2 groups of cows. Cows were 0 or 50% Bos taurus ( 100 or 50% Nellore) breed type: Nellore cows (NL; n = 10) mated to Nellore bulls, NL cows ( n = 9) mated to Angus bulls, Angus x Nellore (ANL; n = 10) and Simmental x Nellore (SNL; n = 10) cows mated to Canchim (5/ 8 Charolais 3/ 8 Zebu) bulls. Cows were individually fed a total mixed diet that contained 11.3% CP and 2.23 Mcal of ME/kg of DM. At 14-d intervals, cows and calves were weighed and the amount of DM was adjusted to keep shrunk BW and BCS of cows constant. Beginning at 38 d of age, corn silage was available to calves ad libitum. Milk production at 42, 98, 126, and 180 d postpartum was measured using the weigh-suckle-weigh technique. At 190 d of age, calves were slaughtered and body composition estimated using 9-10-11th-rib section to obtain energy deposition. Regression of BW change on daily ME intake (MEI) was used to estimate MEI at zero BW change. Increase in percentage Bos taurus had a significant effect on daily ME requirements (Mcal/d) during pregnancy (P < 0.01) and lactation (P < 0.01). Percentage Bos taurus had a positive linear effect on maintenance requirements of pregnant (P = 0.07) and lactating (P < 0.01) cows; during pregnancy, the ME requirements were 91 and 86% of those in lactation (131 +/- 3.5 vs. 145 +/- 3.4 Mcal.kg(-0.75).d(-1)) for the 0 and 50% B. taurus groups, respectively. The 50% B. taurus cows, ANL and SNL, suckling crossbred calves had greater total MEI (4,319 +/- 61 Mcal; P < 0.01) than 0% B. taurus cows suckling NL (3,484 +/- 86 Mcal) or ANL calves (3,600 +/- 91 Mcal). The 0% B. taurus cows suckling ANL calves were more efficient (45.3 +/- 1.6 g/Mcal; P = 0.03) than straightbred NL (35.1 +/- 1.5 g/Mcal) and ANL or SNL pairs (41.0 +/- 1.0 g/Mcal). Under the conditions of this study, crossbreeding improved cow/ calf efficiency and showed an advantage for cows that have lower energy requirements.

IBA application for rooting of Eucalyptus benthamii Maiden and Cambage x Eucalyptus dunnii Maiden minicuttings

IBA application for rooting of Eucalyptus benthamii Maiden and Cambage x Eucalyptus dunnii Maiden minicuttings. Eucalyptus has great importance in the forestry sector and many advances in the area of improvement have been achieved with the advent of biotechnological techniques. However, some promising genotypes still do not have multiplication protocols with cloning techniques, such as minicutting. The study aimed to evaluate IBA concentrations for survival, rooting and vegetative vigor of E. benthamii x E. dunnii minicuttings, and determine the maximum technical efficiency dose. Ministumps H12, H19 and H20 clones were cultivated in a clonal minigarden under a semi-hydroponic system. For rooting, the rninicutting basal portion was plunged in hydro-alcoholic solutions, whose concentrations were: 0; 2,000; 4,000; 6,000 and 8,000 mg L(-1) of IBA. The experiment was conducted in a completely randomized design, with the factors consisting of three clones and five IBA concentrations, with five replications, containing 10 minicuttings per replication. IBA positively influenced the minicutting rooting processes, with differentiated behavior between the clones, with 30.32 to 55.45% rooting variation. The positives increments occurred until the highest IBA concentration for H12 and H19 clones. However, the range between 4,000 and 6,000 mg L(-1) of IBA treatments promoted the best rooting results for the H20 clone.

Allele-Specific Expression of the MAOA Gene and X Chromosome Inactivation in In Vitro Produced Bovine Embryos

During embryogenesis, one of the two X chromosomes is inactivated in embryos. The production of embryos in vitro may affect epigenetic mechanisms that could alter the expression of genes related to embryo development and X chromosome inactivation (XCI). The aim of this study was to understand XCI during in vitro, pre-implantation bovine embryo development by characterizing the allele-specific expression pattern of the X chromosome-linked gene, monoamine oxidase A (MAOA). Two pools of ten embryos, comprised of the 4-, 8- to 16-cell, morula, blastocyst, and expanded blastocyst stages, were collected. Total RNA from embryos was isolated, and the RT-PCR-RFLP technique was used to observe expression of the MAOA gene. The DNA amplicons were also sequenced using the dideoxy sequencing method. MAOA mRNA was detected, and allele-specific expression was identified in each pool of embryos. We showed the presence of both the maternal and paternal alleles in the 4-, 8-to 16-cell, blastocyst and expanded blastocyst embryos, but only the maternal allele was present in the morula stage. Therefore, we can affirm that the paternal X chromosome is totally inactivated at the morula stage and reactivated at the blastocyst stage. To our knowledge, this is the first report of allele-specific expression of an X-linked gene that is subject to XCI in in vitro bovine embryos from the 4-cell to expanded blastocyst stages. We have established a pattern of XCI in our in vitro embryo production system that can be useful as a marker to assist the development of new protocols for in vitro embryo production. Mol. Reprod. Dev. MoL Reprod. Dev. 77: 615-621, 2010. (C) 2010 Wiley-Liss, Inc.

X ray densitometry applied to technological evaluation of MDF panels of eucalyptus

MDF panels from eucalyptus wood fibers were manufactured in laboratory and industrial production and had their apparent density profile determined by X-ray densitometry. The MDF panels apparent density parameters (maximum density of the superior and inferior faces; medium and minimum density) were determined and compared. The results indicated that the density values of the MDF panels made in the laboratory and in industrial line did not show significant statistical differences, indicating the similarities in the pressing phase of the fibers of both kinds. However, for MDF panels of laboratory and production line, the values of maximum, mean and minimum densities showed statistically significant correlations. The determination of the density profile for MDF panels by X-ray densitometry is important for the evaluation of pressing phase and other variables of the industrial process of production, as well for the determination of the technological properties.

Nutrition in bean plants and anthracnose intensity in function of silicon and copper application.

Nutrition in bean plants and anthracnose intensity in function of silicon and copper application. The objective of this work was to evaluate the effect of calcium silicate and copper sulfate on anthracnose intensity and nutrition of bean plants. The experiment was conducted using an experimental design in randomized blocks following a 4 x 4 factorial arrangement , (four levels of calcium silicate and four levels of copper sulfate) and two additional treatments (plants without inoculation and plants sprinkled with Benomyl). Four evaluations of the incidence and severity of anthracnose were done, in addition to measuring, total leaf area. At the end of the evaluations, incidence: and data were integrated over time, obtaining the area under disease progress curve (AUDPC). Contents of N, P, K, Ca, Mg, B, Cu, Fe, Mn, Zn, Si and lignin were determined in the aerial Part. A linear decrease of the intensity AUDPC was observed with the increase of the doses of calcium silicate. The severity AUDPC was influenced by the doses of copper, obtaining a reduction of 35% on the higher dosage. The supply of silicon and copper altered the content of the K, mg, S, Zn, Ca and Si in the aerial part of the bean plants.

Functionality of bioactive compounds in Brazilian strawberry (Fragaria x ananassa Duch.) cultivars: Evaluation of hyperglycemia and hypertension potential using in vitro models

Fruits of seven fully ripened strawberry cultivars grown in Brazil (Dover, Camp Dover, Camarosa, Sweet Charlie, Toyonoka, Oso Grande, and Piedade) were evaluated for total phenolics, antioxidant activity based on DPPH radical scavenging assay, and functionality such as inhibition of alpha-amylase, alpha-glucosidase, and angiotensin I-converting enzyme (ACE) relevant for potentially managing hyperglycemia and hypertension. The total phenolics content ranged from 966 to 1571 mu g of gallic acid/g of fruit fresh weight for Toyonoka and Dover, respectively. No correlation was found between total phenolics and antioxidant activity. The major phenolic compounds in aqueous extracts of strawberries were ellagic acid, quercetin, and chlorogenic acid. Strawberries had high alpha-glucosidase inhibitory activity. However, alpha-amylase inhibitory activity was very low in all cultivars. This suggested that strawberries could be considered as a potential dietary source with anti-hyperglycemic potential. The evaluated cultivars had no significant ACE inhibitory activity, reflecting low anti-hypertensive potential.