Heat transfer coefficients from Newtonian and non-Newtonian fluids flowing in laminar regime in a helical coil

This study aimed to carry out experimental work to obtain, for Newtonian and non-Newtonian fluids, heat transfer coefficients, at constant wall temperature as boundary condition, in fully developed laminar flow inside a helical coil. The Newtonian fluids studied were aqueous solutions of glycerol, 25%, 36%, 43%, 59% and 78% (w/w) and the non-Newtonian fluids aqueous solutions of carboxymethylcellulose (CMC), a polymer, with concentrations 0.1%, 0.2%, 0.3%, 0.4% and 0.6% (w/w) and aqueous solutions of xanthan gum (XG), another polymer, with concentrations 0.1% and 0.2% (w/w). According to the rheological study performed, the polymer solutions had shear thinning behavior and different values of elasticity. The helical coil used has internal diameter, curvature ratio, length and pitch, respectively: 0.004575 m, 0.0263, 5.0 m and 11.34 mm. The Nusselt numbers for the CMC solutions are, on average, slightly higher than those for Newtonian fluids, for identical Prandtl and generalized Dean numbers. As outcome, the viscous component of the shear thinning polymer tends to potentiate the mixing effect of the Dean cells. The Nusselt numbers of the XG solutions are significant lower than those of the Newtonian solutions, for identical Prandtl and generalized Dean numbers. Therefore, the elastic component of the polymer tends to diminish the mixing effect of the Dean cells. A global correlation, for Nusselt number as a function of Péclet, generalized Dean and Weissenberg numbers for all Newtonian and non-Newtonian solutions studied, is presented.

Evaluation of dynamic pass-through of carbon prices into electricity prices – a cointegrated VECM analysis

This paper addresses the impact of the CO2 opportunity cost on the wholesale electricity price in the context of the Iberian electricity market (MIBEL), namely on the Portuguese system, for the period corresponding to the Phase II of the European Union Emission Trading Scheme (EU ETS). In the econometric analysis a vector error correction model (VECM) is specified to estimate both long–run equilibrium relations and short–run interactions between the electricity price and the fuel (natural gas and coal) and carbon prices. The model is estimated using daily spot market prices and the four commodities prices are jointly modelled as endogenous variables. Moreover, a set of exogenous variables is incorporated in order to account for the electricity demand conditions (temperature) and the electricity generation mix (quantity of electricity traded according the technology used). The outcomes for the Portuguese electricity system suggest that the dynamic pass–through of carbon prices into electricity prices is strongly significant and a long–run elasticity was estimated (equilibrium relation) that is aligned with studies that have been conducted for other markets.

Performance of concrete made with aggregates recycled from precasting industry waste: influence of the crushing process

The aim of this paper is to evaluate the influence of the crushing process used to obtain recycled concrete aggregates on the performance of concrete made with those aggregates. Two crushing methods were considered: primary crushing, using a jaw crusher, and primary plus secondary crushing (PSC), using a jaw crusher followed by a hammer mill. Besides natural aggregates (NA), these two processes were also used to crush three types of concrete made in laboratory (L20, L45 e L65) and three more others from the precast industry (P20, P45 e P65). The coarse natural aggregates were totally replaced by coarse recycled concrete aggregates. The recycled aggregates concrete mixes were compared with reference concrete mixes made using only NA, and the following properties related to the mechanical and durability performance were tested: compressive strength; splitting tensile strength; modulus of elasticity; carbonation resistance; chloride penetration resistance; water absorption by capillarity; water absorption by immersion; and shrinkage. The results show that the PSC process leads to better performances, especially in the durability properties. © 2014 RILEM

Impact of a price-maker pumped storage hydro unit on the integration of wind energy in power systems

The increasing integration of larger amounts of wind energy into power systems raises important operational issues, such as the balance between power generation and demand. The pumped storage hydro (PSH) units are one possible solution to mitigate this problem, once they can store the excess of energy in the periods of higher generation and lower demand. However, the behaviour of a PSH unit may differ considerably from the expected in terms of wind power integration when it operates in a liberalized electricity market under a price-maker context. In this regard, this paper models and computes the optimal PSH weekly scheduling in a price-taker and price-maker scenarios, either when the PSH unit operates in standalone and integrated in a portfolio of other generation assets. Results show that the price-maker standalone PSH will integrate less wind power in comparison with the price-taker situation. Moreover, when the PSH unit is integrated in a portfolio with a base load power plant, the role of the price elasticity of demand may completely change the operational profile of the PSH unit. (C) 2014 Elsevier Ltd. All rights reserved.

In vitro assessment of three dimensional dense chitosan-based structures to be as bioabsorbable implants

Chitosan biocompatibility and biodegradability properties make this biopolymer promising for the development of advanced internal fixation devices for orthopedic applications. This work presents a detailed study on the production and characterization of three dimensional (3D) dense, non-porous, chitosan-based structures, with the ability to be processed in different shapes, and also with high strength and stiffness. Such features are crucial for the application of such 3D structures as bioabsorbable implantable devices. The influence of chitosan's molecular weight and the addition of one plasticizer (glycerol) on 3D dense chitosan-based products' biomechanical properties were explored. Several specimens were produced and in vitro studies were performed in order to assess the cytotoxicity of these specimens and their physical behavior throughout the enzymatic degradation experiments. The results point out that glycerol does not impact on cytotoxicity and has a high impact in improving mechanical properties, both elasticity and compressive strength. In addition, human mesenchymal stem/stromal cells (MSC) were used as an ex-vivo model to study cell adhesion and proliferation on these structures, showing promising results with fold increase values in total cell number similar to the ones obtained in standard cell culture flasks. (C) 2014 Elsevier Ltd. All rights reserved.

Probabilistic models for mechanical properties of prestressing strands

This study focus on the probabilistic modelling of mechanical properties of prestressing strands based on data collected from tensile tests carried out in Laboratório Nacional de Engenharia Civil (LNEC), Portugal, for certification purposes, and covers a period of about 9 years of production. The strands studied were produced by six manufacturers from four countries, namely Portugal, Spain, Italy and Thailand. Variability of the most important mechanical properties is examined and the results are compared with the recommendations of the Probabilistic Model Code, as well as the Eurocodes and earlier studies. The obtained results show a very low variability which, of course, benefits structural safety. Based on those results, probabilistic models for the most important mechanical properties of prestressing strands are proposed.

The effect of superplasticizers on the mechanical performance of concrete made with fine recycled concrete aggregates

It is considered that using crushed recycled concrete as aggregate for concrete production is a viable alternative to dumping and would help to conserve abiotic resources. This use has fundamentally been based on the coarse fraction because the fine fraction is likely to degrade the performance of the resulting concrete. This paper presents results from a research work undertaken at Institut Superior Tecnico (IST), Lisbon, Portugal, in which the effects of incorporating two types of superplasticizer on the mechanical performance of concrete containing fine recycled aggregate were evaluated. The purpose was to see if the addition of superplasticizer would offset the detrimental effects associated with the use of fine recycled concrete aggregate. The experimental programme is described and the results of tests for splitting tensile strength, modulus of elasticity and abrasion resistance are presented. The relative performance of concrete made with recycled aggregate was found to decrease. However, the same concrete with admixtures in general exhibited a better mechanical performance than the reference mixes without admixtures or with a less active superplasticizer. Therefore, it is argued that the mechanical performance of concrete made with fine recycled concrete aggregates can be as good as that of conventional concrete, if superplasticizers are used to reduce the water-cement ratio of the former concrete.

Liquid crystal beads constrained on thin cellulosic fibers: Electric field induced microrotors and N-I transition

We directly visualize the response of nematic liquid crystal drops of toroidal topology threaded in cellulosic fibers, suspended in air, to an AC electric field and at different temperatures over the N-I transition. This new liquid crystal system can exhibit non-trivial point defects, which can be energetically unstable against expanding into ring defects depending on the fiber constraining geometries. The director anchoring tangentially near the fiber surface and homeotropically at the air interface makes a hybrid shell distribution that in turn causes a ring disclination line around the main axis of the fiber at the center of the droplet. Upon application of an electric field, E, the disclination ring first expands and moves along the fiber main axis, followed by the appearance of a stable "spherical particle" object orbiting around the fiber at the center of the liquid crystal drop. The rotation speed of this particle was found to vary linearly with the applied voltage. This constrained liquid crystal geometry seems to meet the essential requirements in which soliton-like deformations can develop and exhibit stable orbiting in three dimensions upon application of an external electric field. On changing the temperature the system remains stable and allows the study of the defect evolution near the nematic-isotropic transition, showing qualitatively different behaviour on cooling and heating processes. The necklaces of such liquid crystal drops constitute excellent systems for the study of topological defects and their evolution and open new perspectives for application in microelectronics and photonics.

How market power affects the behaviour of a pumped storage hydro unit in the day-ahead electricity market?

The integration of large amounts of wind energy in power systems raises important operation issues such as the balance between power demand and generation. The pumped storage hydro (PSH) units are seen as one solution for this issue, avoiding the need for wind power curtailments. However, the behavior of a PSH unit might differ considerably when it operates in a liberalized market with some degree of market power. In this regard, a new approach for the optimal daily scheduling of a PSH unit in the day-ahead electricity market was developed and presented in this paper, in which the market power is modeled by a residual inverse demand function with a variable elasticity. The results obtained show that increasing degrees of market power of the PSH unit correspond to decreasing levels of storage and, therefore, the capacity to integrate wind power is considerably reduced under these circumstances.

Sustentabilidade na reablitação urbana

A indústria da construção é um setor com grande impacto na economia, no Produto Interno Bruto (PIB) e ainda em postos de trabalho diretos e indiretos. No entanto, é um dos setores com maior impacte ambiental. Com a crise económica e financeira que o país atravessa, este setor foi um dos mais afetados, contribuindo para o aumento do desemprego visto tratar-se do setor com maior taxa de empregabilidade. Concomitantemente, ocorre saturação do mercado com a construção nova e desertificação dos centros urbanos com a degradação das habitações. Assim, como impulsionador da economia, surge a aposta na reabilitação do parque edificado que, com a legislação em vigor e com os incentivos dados pela tutela tem tudo para impulsionar o setor. Sabendo que a indústria da construção é um dos setores com maiores impactes ambientais, faz todo o sentido reabilitar-se de uma forma mais sustentável. Aplicando os princípios da sustentabilidade a todo o ciclo de vida do edifício, conseguimos reduzir os recursos na fase de construção (resíduos de construção) e na fase de exploração (consumo de energia e de água). Podemos ainda reduzir os custos de energia para climatização ao termos em conta a orientação do edifício e a envolvente, os recursos naturais e aplicando tecnologias solares passivas. Assim, ao aplicarmos os princípios da construção sustentável na reabilitação urbana podemos diminuir os impactes ambientais, a produção de CO2, as emissões de gases com efeito de estufa, os resíduos de construção e a área impermeabilizada.

Diagnóstico e avaliação da segurança de estruturas de madeira existentes

A utilização da madeira enquanto material estrutural é um aspeto abordado com algum receio ou até desconhecimento por parte dos elementos intervenientes no processo de construção civil, sendo ainda uma área pouco lecionada e muitas vezes excluída dos planos curriculares em Engenharia Civil. Assim sendo é importante o surgimento de trabalhos relacionados com esta matéria, relembrando ao sector da construção civil e ao ramo de estudo relacionado, que a madeira já teve e possivelmente voltará a ter um papel importante a desempenhar na área da construção. Um dos aspetos evidenciados nos estudos realizados consiste na importância da reabilitação de edifícios e do seu papel cada vez mais determinante na sociedade. Esta metodologia de intervenção apresenta-se muitas vezes como uma vantagem económica assim como contribui para a preservação do património arquitetónico e cultural, cujo valor histórico é incalculável. A importância da reabilitação de edifícios habitacionais nas zonas históricas, bem como de monumentos de grande importância cultural apresenta-se cada vez mais como um desafio devido à falta de conservação dos mesmos ao longo da sua vida útil, e da necessidade de preservar a identidade do local, beneficiando assim a qualidade do tecido urbano. Assim sendo, este trabalho apresenta um levantamento dos danos possíveis de ocorrer em elementos de madeira, dando especial destaque aos agentes patológicos e às consequências da sua atividade na madeira assim como às metodologias de inspeção e diagnóstico que poderão ser aplicadas em estruturas de madeira existentes, favorecendo assim a vertente da reabilitação ao invés da demolição. Estas metodologias recorrem a ensaios não destrutivos, como é exemplo o Pilodyn, o Resistógrafo, o Ultra-sons, etc., referindo também o recurso a ensaios destrutivos, cuja utilização terá de ser uma questão muito bem ponderada devido às consequências que implica. Por fim, apresenta-se um caso real de estudo em que se analisa um pavimento em madeira através da aplicação de metodologias de ensaio não destrutivas e destrutivas a amostras recolhidas. O objetivo será determinar o estado de conservação da madeira e algumas características físicas tais como a sua densidade e os módulos de elasticidade, sendo posteriormente efetuada uma análise estrutural. Os resultados obtidos permitem efetuar uma avaliação qualitativa do estado geral do pavimento sendo as principais conclusões que o pavimento se encontra atacado por parte de insetos xilófagos e apresenta problemas a nível de verificação a estados limite de utilização, deformação e vibração, fator que condiciona a possível utilização do pavimento.

Towards high-available and energy-efficient virtual computing environments in the cloud

Empowered by virtualisation technology, cloud infrastructures enable the construction of flexi- ble and elastic computing environments, providing an opportunity for energy and resource cost optimisation while enhancing system availability and achieving high performance. A crucial re- quirement for effective consolidation is the ability to efficiently utilise system resources for high- availability computing and energy-efficiency optimisation to reduce operational costs and carbon footprints in the environment. Additionally, failures in highly networked computing systems can negatively impact system performance substantially, prohibiting the system from achieving its initial objectives. In this paper, we propose algorithms to dynamically construct and readjust vir- tual clusters to enable the execution of users’ jobs. Allied with an energy optimising mechanism to detect and mitigate energy inefficiencies, our decision-making algorithms leverage virtuali- sation tools to provide proactive fault-tolerance and energy-efficiency to virtual clusters. We conducted simulations by injecting random synthetic jobs and jobs using the latest version of the Google cloud tracelogs. The results indicate that our strategy improves the work per Joule ratio by approximately 12.9% and the working efficiency by almost 15.9% compared with other state-of-the-art algorithms.

Parasitological and serological studies on Amoebiasis and other intestinal parasitic infections in Recife and its suburban area, northeast Brazil

Parasitological examinations were carried out during April to August, 1987, with 187 out-patients of the IMIP hospital, located in the center of Recife City, and 464 inhabitants of several villages around Cabo City, 50 Km southeast of Recife, Pernambuco, Brazil. Approximately 71% of the IMIP patients and 92% of the Cabo inhabitants were infected with at least one species of intestinal parasite. There was minimum difference in the prevalence rate of Trichuris trichiura between two areas, whereas the prevalence rates of Ascaris lumbricoides, hookworms, Strongyloides stercoralis, Schistosoma mansoni and Entamoeba histolytica were higher in the inhabitants of the Cabo City area. Only Giardia lamblia was more prevalent in the out-patients of IMIP hospital. Test tube cultivation revealed that the prevalence rate of Necator americanus in both areas was much higher than that of Ancylostoma duodenale , and also that the prevalence rate of S. stercoralis of the IMIP patients and Cabo inhabitants were 4.5% and 9.6%, respectively. Six hundred and fifteen sera were serologically examined for amoebiasis by the gel diffusion precipitation test (GDP) and enzyme linked immunosorbent assay (ELISA) using the antigen prepared from axenically cultured trophozoite of E. histolytica (strain HM-ITMSS). No positive reaction was observed in all of the sera as examined by GDP, while 32 out of 615 sera were positive on ELISA.

Contributo das tecnologias de informação na gestão do regime terapêutico no diabético

A diabetes é a doença do seculo XXI, atinge mais de um milhão de portugueses cada vez mais jovens em idades trabalhadoras, e já custa mais de 1% do PIB, além dos enormes danos que pode causar às pessoas e à sociedade. Segundo o Relatório Anual do Observatório Nacional da Diabetes, em 2011, cerca de um quarto da população portuguesa integrada no escalão etário dos 60 aos 79 tem Diabetes. Um estudo realizado pelo Lisbon Internet and Networks Institute (LINI), em 2010, diz-nos que “a internet é um recurso para a informação e educação para a saúde”. Em 2010 49% dos lares portugueses possuem acesso à internet e 44% da população é utilizadora (acréscimo significativo relativamente aos 29% em 2003). Destes, dois terços têm entre os 15 e os 24 anos. Os idosos representam 1,6%, dos quais os reformados e pensionistas representam 5%, as domésticas representam 11% e os trabalhadores manuais 22%, sendo estes os menos utilizadores. Um terço da restante população procura informação sobre saúde semanalmente, cerca de 16%. Face à atual conjuntura económica, com restrições orçamentais, nomeadamente na área da saúde, devem-se encontrar meios para prevenir e lidar com a Diabetes numa perspetiva de custo-benefício, isto porque a Diabetes pode reduzir as oportunidades de emprego e de aprendizagem. O atual diretor da Organização para a Cooperação e Desenvolvimento Económico (OCDE) Yyes Leterme diz que “Prevenir e tratar a Diabetes e as suas complicações custa cerca de 90 mil milhões de euros anualmente na Europa”. Atualmente, não é muito utilizado nem explorado o potencial das tecnologias de informação e as ferramentas web ao serviço da saúde, quer por profissionais de saúde, quer por utentes na gestão ao regime terapêutico na doença crónica, mais precisamente na gestão adequada da Diabetes. Potenciar uma visão integrada dos diferentes recursos de comunicação e a sua utilização conjugada com a promoção da saúde e prevenção da doença poderá enfatizar em termos de eficácia e eficiência a minimização de recursos das organizações de saúde e promover a gestão adequada da Diabetes. Tendo por base esta problemática, este estudo pretende abordar e refletir o possível contributo das tecnologias de informação e das ferramentas web na gestão adequada ao regime terapêutico da Diabetes.

Parasitological and serological studies on amoebiasis and other intestinal parasitic infections in the rural sector around Recife, Northeast Brazil

Parasitological examinations were carried out during July to December, 1989, on 485 inhabitants of four villages in São Lourenço da Mata, 25 km northwest of Recife, Pernambuco, Brazil. Approximately 99.6% of the inhabitants were infected with at least one species of intestinal parasites. A high prevalence of Schistosoma mansoni (82.1%), hookworm (80.2%) Trichuris trichiura (69.9%), Ascaris lumbricoides (61.9%) and Entamoeba coli (36.7%) infections were demonstrated. Test tube cultivation revealed that the most common species of hookworm in this region was Necator americanus (88.4%), and also that the prevalence of Strongyloides stercoralis was 5.8%. Three hundred and thirty-four sera were serologically examined for amoebiasis by the gel diffusion precipitation test (GDP) and enzyme-linked immunosorbent assay (ELISA). No positive reaction was observed in all sera as examined by GDP, while 24 sera were positive by ELISA.