Electrodeposited reduced-graphene oxide/cobalt oxide electrodes for charge storage applications

In the present work, electrochemically reduced-graphene oxide/cobalt oxide composites for charge storage electrodes were prepared by a one-step pulsed electrodeposition route on stainless steel current collectors and after that submitted to a thermal treatment at 200 degrees C. A detailed physico-chemical characterization was performed by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and Raman spectroscopy. The electrochemical response of the composite electrodes was studied by cyclic voltammetry and charge-discharge curves and related to the morphological and phase composition changes induced by the thermal treatment. The results revealed that the composites were promising materials for charge storage electrodes for application in redox supercapacitors, attaining specific capacitances around 430 F g(-1) at 1 A g(-1) and presenting long-term cycling stability. (C) 2016 Elsevier B.V. All rights reserved.

Dynamic model development of adiabatic compressed air energy storage

The share of variable renewable energy in electricity generation has seen exponential growth during the recent decades, and due to the heightened pursuit of environmental targets, the trend is to continue with increased pace. The two most important resources, wind and insolation both bear the burden of intermittency, creating a need for regulation and posing a threat to grid stability. One possibility to deal with the imbalance between demand and generation is to store electricity temporarily, which was addressed in this thesis by implementing a dynamic model of adiabatic compressed air energy storage (CAES) with Apros dynamic simulation software. Based on literature review, the existing models due to their simplifications were found insufficient for studying transient situations, and despite of its importance, the investigation of part load operation has not yet been possible with satisfactory precision. As a key result of the thesis, the cycle efficiency at design point was simulated to be 58.7%, which correlated well with literature information, and was validated through analytical calculations. The performance at part load was validated against models shown in literature, showing good correlation. By introducing wind resource and electricity demand data to the model, grid operation of CAES was studied. In order to enable the dynamic operation, start-up and shutdown sequences were approximated in dynamic environment, as far as is known, the first time, and a user component for compressor variable guide vanes (VGV) was implemented. Even in the current state, the modularly designed model offers a framework for numerous studies. The validity of the model is limited by the accuracy of VGV correlations at part load, and in addition the implementation of heat losses to the thermal energy storage is necessary to enable longer simulations. More extended use of forecasts is one of the important targets of development, if the system operation is to be optimised in future.

Design and stability study of a paediatric oral solution of methotrexate 2mg/ml

International audience

Synthesis and structural stability of metal-organic frameworks

Metal-organic frameworks (MOFs) have attracted significant attention during the past decade due to their high porosity, tunable structures, and controllable surface functionalities. Therefore many applications have been proposed for MOFs. All of them however are still in their infancy stage and have not yet been brought into the market place. In this thesis, the background of the MOF area is first briefly introduced. The main components and the motifs of designing MOFs are summarized, followed by their synthesis and postsynthetic modification methods. Several promising application areas of MOFs including gas storage and separation, catalysis and sensing are reviewed. The current status of commercialization of MOFs as new chemical products is also summarized. Examples of the design and synthesis of two new MOF structures Eu(4,4′,4′′,4′′′-(porphine-5,10,15,20-tetrayl)tetrakis(benzoic acid))·2H2O∙xDMF and Zn4O(azobenzene-4,4’-dicarboxylic acid)3∙xNMP are described. The first one contains free-base porphyrin centers and the second one has azobenzene components. Although the structures were synthesized as designed, unfortunately they did not possess the expected properties. The research idea to use MOFs as template materials to synthesize porous polymers is introduced. Several methods are discussed to grow PMMA into IRMOF-1 (Zn4O(benzene-1,4-dicarboxylate)3, IR stands for isoreticular) structure. High concentration of the monomers resulted in PMMA shell after MOF digestion while with low concentration of monomers no PMMA was left after digestion due to the small iii molecular weight. During the study of this chapter, Kitagawa and co-workers published several papers on the same topic, so this part of the research was terminated thereafter. Many MOFs are reported to be unstable in air due to the water molecules in air which greatly limited their applications. By incorporating a number of water repelling functional groups such as trifluoromethoxy group and methyl groups in the frameworks, the water stability of MOFs are shown to be significantly enhanced. Several MOFs inculding Banasorb-22 (Zn4O(2-trifluoromethoxybenzene-1,4-dicarboxylate)3), Banasorb-24 (Zn4O(2, 5-dimethylbenzene-1,4-dicarboxylate)3) and Banasorb-30 (Zn4O(2-methylbenzene-1,4-dicarboxylate)3) were synthesized and proved to have isostructures with IRMOF-1. Banasorb-22 was stable in boiling water steam for one week and Banasorb-30’s shelf life was over 10 months under ambient condition. For comparison, IRMOF-1’s structure collapses in air after a few hours to several days. Although MOF is a very popular research area nowadays, only a few studies have been reported on the mechanical properties of MOFs. Many of MOF’s applications involve high pressure conditions, so it is important to understand the behavior of MOFs under elivated pressures. The mechanical properties of IRMOF-1 and a new MOF structure Eu2(C12N2O4H6)3(DEF)0.87(H2O)2.13 were studied using diamond anvil cells at Advanced Photon Source. IRMOF-1 experienced an irriversible phase transtion to a nonporous phase followed by amorphization under high pressure. Eu2(C12N2O4H6)3(DEF)0.87(H2O)2.13 showed reversible compression under pressure up to 9.08GPa.

Suomalaisten marjojen fenoliyhdisteet ja niiden stabiilisuus prosessoinnin ja säilytyksen aikana

Suomalaiset marjat sisältävät huomattavia määriä erilaisia fenoliyhdisteitä ja ne ovat siksi erinomaisia fenoliyhdisteiden lähteitä moniin muihin elintarvikkeisiin verrattuna. Fenoliyhdisteet ovat kasveissa syntyviä aineenvaihduntatuotteita, joilla on todettu olevan terveyden kannalta positiivia vaikutuksia. Ne antavat kasvikunnan tuotteille niiden tunnusomaisen värin sekä toimivat suoja-aineina taudinaiheuttajia vastaan. Erityisesti elintarvike-, lääke- ja kosmetiikkateollisuus jalostavat marjoja erilaisiksi lopputuotteiksi. Fenoliyhdisteet tuovat näihin tuotteisiin hyödyllisiä terveysvaikutuksia ja ne voivat toimia niissä myös väripigmentteinä. Fenoliyhdisteet ovat kuitenkin suhteellisen epästabiileja yhdisteitä. On havaittu, että prosessointi- ja säilytystavat vaikuttavat huomattavasti niiden stabiilisuuteen ja hajoamiseen. Tämän kandidaatintyön tavoitteena oli selvittää fenoliyhdisteiden stabiilisuuteen vaikuttavia tekijöitä prosessoinnin ja säilytyksen aikana kirjallisuuden pohjalta. Tämän työn tulosten perusteella marjojen prosessointi kannattaa suorittaa mahdollisimman lyhyessä ajassa matalissa lämpötiloissa, sillä monet fenoliyhdisteistä eivät ole pitkään lämpöstabiileja. Säilytys kannattaa tehdä myös matalissa lämpötiloissa; pitkänä säilytysaikana pakastettuna. Korkea pH vaikuttaa usean fenoliyhdisteen hajoamiseen ja se saattaa aiheuttaa tuotteissa värinmuutoksia. Valo, hapen läsnäolo sekä erilaiset muut yhdisteet voivat vaikuttaa heikentävästi fenoliyhdisteiden stabiilisuuteen sekä prosessoinnin että säilytyksen aikana. Fenoliyhdisteiden stabiilisuus on hyvin rakennekohtaista ja siksi prosessoinnin ja säilytyksen tarkkojen vaikutusten yleistäminen kaikkiin fenoliyhdisteisiin on vaikeaa.

Physicochemical Stability of Poly(lactide-co-glycolide) Nanocapsules Containing the Local Anesthetic Bupivacaine

This paper describes the preparation of poly(DL-lactide-co-glicolide) (PLGA) nanocapsules as a drug carrier system for the local anesthetic bupivacaine. The system was characterized and its stability investigated. The results showed a size distribution with a polydispersity index of 0.12, an average diameter of 148 nm, a zeta potential of -43.5 mV and an entrapment efficiency of 75.8%. The physicochemical properties of polymeric nanocapsule suspensions (average diameter, polydispersity, zeta potential and drug association efficiency) were evaluated as a function of time to determine the formulation stability. The formulation did not display major changes in these properties over the time, and it was considered stable up to 120 days of storage at room temperature. The results reported here which refer to the initial characterization of these new formulations for the local anesthetic bupivacaine show a promising potential for future in vivo studies.

Transcription of alternative oxidase (AOX) and plastid terminal oxidase (PTOX) during stress-regulated root tissue growth in Daucus carota L. - An approach to identify functional marker candidates for breeding on carrot yield stability

A presente tese explora a hipótese de utilização dos genes da oxidase alternativa (AOX) e da oxidase terminal da plastoquinona (PTOX) como genes-alvo para o desenvolvimento de marcadores funcionais (MF) para avaliar a performance do crescimento em cenoura, fator determinante da produtividade. Para avaliar se os referidos genes estão associados com o crescimento da cenoura procedeu—se ao seu isolamento e posterior análise dos seus perfis de transcrição em diversos sistemas biológicos. O sistema in vitro selecionado, denominado sistema de culturas primárias, permitiu avaliar alterações na quantidade de transcritos desses genes durante os processos de reprogramação celular e crescimento. Ao nível da planta foi também estudado o efeito do frio na expressão precoce dos genes AOX. Ambos os genes DcAOX1 e DcAOX2a revelaram uma resposta rápida e um padrão semelhante apos stresse (inoculação in vitro e resposta ao frio). Foi igualmente verificado um incremento na expressão do gene DcPTOX durante a fase inicial do processo de reprogramação celular. Estudos de expressão dos genes AOX durante o desenvolvimento da raiz da cenoura revelaram que o gene DcAOX2a será potencialmente o gene mais envolvido neste processo. De modo a avaliar a hipótese de envolvimento do gene DcPTOX no crescimento da raíz procederam—se a estudos de expressão ao nível do tecido meristemático. Todavia, para um mais completo entendimento da ligação entre DcPTOX e o crescimento secundário e/ou acumulação de carotenos, a expressão do gene DcPTOX foi também avaliada em raízes de cenoura durante o desenvolvimento, utilizando cultivares caracterizadas por distintos conteúdos de carotenos. Os resultados obtidos demonstraram a associação do gene DcPTOX a ambos os processos. O envolvimento da PTOX no crescimento adaptativo da raiz foi analisado com um ensaio que permitiu identificar, no tecido meristemático, uma resposta precoce do gene DcPTOX face a uma diminuição da temperatura. Adicionalmente, foi efetuada a seleção de genes de referência para uma analise precisa da expressão génica por RT-qPCR em diversos sistemas biológicos de cenoura, e a importância do seu estudo ao nível do sistema biológico foi realçada. Os resultados desta tese são encorajadores para prosseguir os estudos de utilização dos genes AOX e PTOX como MF no melhoramento da performance do crescimento adaptativo em cenoura, fator determinante para a produtividade; ABSTRACT: This thesis explores the hypothesis of using the alternative oxidase (AOX) and theplastid terminal oxidase (PTOX) as target genes for functional marker (FM) development for yield-determining growth performance in carrot. To understand if these genes are associated to growth, different AOX gene family members and the single PTOX gene were isolated, and their expression patterns evaluated in diverse carrot plant systems. An in-vitro primary culture system was selected to study AOX and PTOX transcript changes during cell reprogramming and growth performance. At plant level, a putative early response of AOX to chilling was also evaluated. In fact, both DcAOXl and DcAOXZa were early responsive and showed similar patterns under stress conditions (in vitro inoculation and chilling). A role for DcPTOX during earliest events of cell reprogramming was also suggested. Next, the expression profiles of AOX gene family members during carrot tap root development were investigated. DcAOXZa was identified as the most responsive gene to root development. In order to evaluate if DcPTOX is associated with carrot tap root growth performance, DcPTOX transcript levels were measured in the central root meristem. To further understand whether DcPTOX is associated with secondary growth and/or carotenoids accumulation, DcPTOX expression was also studied in deveIOping carrot tap roots in cultivars with different carotenoids contents. The results indicated that DcPTOX associates to both carotenoid biosynthesis and secondary growth during storage root development. To obtain further insights into the involvement of PTOX on adaptive growth, the early effects of temperature decrease were explored in the root meristem, where a short—term early response in DcPTOX was found, probably associated with adaptive growth. Furthermore, a selection of the most suitable reference genes for accurate RT—qPCR analysis in several carrot experimental systems was performed and discussed. The present research provides the necessary toolbox for continuing studies in carrot AOX and PTOX genes as promising resources for FM candidates in order to assist breeding on yield—determining adaptive growth performance.

The effect of chaperone compounds on glucocerebrosidase stability and activity in fibroblasts from Gaucher Disease patients with different genotypes

Dissertação de mestrado, Ciências Biomédicas, Departamento de Ciências Biomédicas e Medicina, Universidade do Algarve, 2014

Dimensional changes of impression materials after 6 months storage period

Poster presented at the 24th Annual Meeting of the Portuguese Dental Association, 12-14 November 2015 Meo Arena, Lisboa, Portugal.

Alterations in monovarietal, blended and aromatized Portuguese virgin olive oils under four storage conditions for 12 months

"Though olive oil is a perishable product, there is not a European regulation for maximum consumption time after production, in part because its durability depends on the storage conditions. The main objectives of this study were to compare the influence of the type of storage on changes of Portuguese virgin olive oils and to verify whether the addition of Catostylus tagi could increase the oxidative stability of olive oil. Over 12 months, the conservation status of monovarietal and blended olive oils in four contexts possible to be used by the consumer was monitored. The analyzed parameters were chlorophyll content, free acidity, peroxide value, specific extinction coefficients at 232 and 270 nm and delta K. Spaced determinations of iodine index and total tocopherol contents complemented the study. Results showed that at Mediterranean temperatures and normal storage procedure, the mean time to reach maximum peroxides value was 12–13 months. At artificial light storage, C. tagi was effective in reducing peroxides evolution by 11 %."

Formulation and stability of topical water in oil emulsion containing corn silk extract

Purpose: To formulate the water in oil (W/O) emulsion of corn silk (CS) extract and to evaluate its stability at various storage conditions. Methods: Ethanol CS extract was prepared using maceration (cold) technique. A 4 % CS emulsion was prepared using varying concentrations of liquid paraffin, ABIL EM90 and water. The formulations were kept at 40 oC for 28 days and to screen out the less stable formulations. The remaining formulations were further stressed at 50 oC to choose the most stable formulation. The optimized formulation was evaluated for physical characteristics including phase separation, rheology and mean droplet size. The physical stability of the formulation was evaluated by monitoring these parameters over a period of 12 weeks at 8, 25, 40 and 40 oC, and 75 % RH. Results: The chosen formulation showed good resistance to phase separation on centrifugation under all storage conditions. Rheological behavior followed non-Newtonian pseudoplastic pattern at various storage conditions. Mean droplet size of freshly prepared formulation was 2.98 ± 1.32 µm and did not show significant (p < 0.05) changes at normal storage conditions (8 and 25 oC). Conclusion: The findings indicate that the developed CS extract W/O emulsion is stable and therefore may be suitable for topical use on skin as an antioxidant preparation.

Microporous organic polymers based on hexaphenylbiadamantane:synthesis, ultra-high stability and gas capture

Hexaphenylbiadamantane-based microporous organic polymers (MOPs) were successfully synthesized by Suzuki coupling under mild conditions. The obtained MOPs show high surface area (891 m2 g−1), ultra-high thermal (less than 40% mass loss at temperatures up to 1000 °C) and chemical (no apparent decomposition in organic solvents for more than 7 days) stability, gas (H2, CO2, CH4) capture capabilities and vapor (benzene, hexane) adsorption. These combined abilities render the synthesized MOPs an attractive candidate as thermo-chemically stable adsorbents for practical use in gas storage and pollutant vapor adsorption.

Maltodextrin-incorporated-vacuum-dried honey powder: processing and stability

Honey is rich in sugar content and dominated by fructose and glucose that make honey prone to crystallize during storage. Due to honey composition, the anhydrous glass transition temperature of honey is very low that makes honey difficult to dry alone and drying aid or filler is needed to dry honey. Maltodextrin is a common drying aid material used in drying of sugar-rich food. The present study aims to study the processing of honey powder by vacuum drying method and the impact of drying process and formulation on the stability of honey powder. To achieve the objectives, the series of experiments were done: investigating of maltodextrin DE 10 properties, studying the effect of drying temperature, total solid concentration, DE value, maltodextrin concentration and anti-caking agent on honey powder processing and stability. Maltodextrin provide stable glass compared to lower molecular weight sugars. Dynamic Dew Point Isotherm (DDI) data could be used to determine amorphous content of a system. The area under the first derivative curve from DDI curve is equal to the amount of water needed by amorphous material to crystallize. The drying temperature affected the amorphous content of vacuum-dried honey powder. The higher temperature seemed to result in honey powder with more amorphous component. The ratio of maltodextrin affected more significantly the stability of honey powder compared to the treatments of total solids concentration, DE value and drying temperature. The critical water activity of honey powder was lower than water activity of the equilibrium water content corresponding to BET monolayer water content. Addition of anti-caking agent increased stability and flow-ability of honey powder. Addition of Calcium stearate could inhibit collapse of the honey powder during storage.

Quantification of storage proteins during seed imbibition of native species from the brazilian Caatinga vegetation.

Poincianella pyramidalis (Fabaceae), Schinopsis brasiliensis (Anacardiaceae) and Sideroxylon obtusifolium (Sapotaceae) are native species of the Caatinga vegetation from Northeastern Brazil and have both biological importance and potential economic uses. Little is known about the water uptake and degradation of storage proteins during seed germination of these species. The aim of this study was to evaluate the imbibition and quantify the amount of storage proteins during seed germination of P. pyramidalis, S. brasiliensis and S. obtusifolium. Two lots of S. obtusifolium seeds with different vigour were used. Four replicates of 20 seeds of P. pyramidalis, S. brasiliensis and S. obtusifolium, were sown onto gerboxes with blotting paper soaked in distilled water and incubated during 72, 200 and 624 hours. Before and after imbibition seeds were weighed and frozen at until the sequential extraction and analysis of the seed storage proteins. Based on our results, we conclude that seed germination of P. pyramidalis, S. brasiliensis and S. obtusifolium has a well-defined triphasic imbibition. All storage proteins content of P. pyramidalis and S. brasiliensis seeds degraded along with the seed imbibition. Likewise, the content of albumins, globulins and glutelins decreased as S. obtusifolium seeds absorbed water

Design and Off-design modelling of advanced Power-to-Gas energy storage systems

Power-to-Gas storage systems have the potential to address grid-stability issues that arise when an increasing share of power is generated from sources that have a highly variable output. Although the proof-of-concept of these has been promising, the behaviour of the processes in off-design conditions is not easily predictable. The primary aim of this PhD project was to evaluate the performance of an original Power-to-Gas system, made up of innovative components. To achieve this, a numerical model has been developed to simulate the characteristics and the behaviour of the several components when the whole system is coupled with a renewable source. The developed model has been applied to a large variety of scenarios, evaluating the performance of the considered process and exploiting a limited amount of experimental data. The model has been then used to compare different Power-to-Gas concepts, in a real scenario of functioning. Several goals have been achieved. In the concept phase, the possibility to thermally integrate the high temperature components has been demonstrated. Then, the parameters that affect the energy performance of a Power-to-Gas system coupled with a renewable source have been identified, providing general recommendations on the design of hybrid systems; these parameters are: 1) the ratio between the storage system size and the renewable generator size; 2) the type of coupled renewable source; 3) the related production profile. Finally, from the results of the comparative analysis, it is highlighted that configurations with a highly oversized renewable source with respect to the storage system show the maximum achievable profit.