Quantitative multi-parameter mapping of R1, PD(*), MT, and R2(*) at 3T: a multi-center validation.

Multi-center studies using magnetic resonance imaging facilitate studying small effect sizes, global population variance and rare diseases. The reliability and sensitivity of these multi-center studies crucially depend on the comparability of the data generated at different sites and time points. The level of inter-site comparability is still controversial for conventional anatomical T1-weighted MRI data. Quantitative multi-parameter mapping (MPM) was designed to provide MR parameter measures that are comparable across sites and time points, i.e., 1 mm high-resolution maps of the longitudinal relaxation rate (R1 = 1/T1), effective proton density (PD(*)), magnetization transfer saturation (MT) and effective transverse relaxation rate (R2(*) = 1/T2(*)). MPM was validated at 3T for use in multi-center studies by scanning five volunteers at three different sites. We determined the inter-site bias, inter-site and intra-site coefficient of variation (CoV) for typical morphometric measures [i.e., gray matter (GM) probability maps used in voxel-based morphometry] and the four quantitative parameters. The inter-site bias and CoV were smaller than 3.1 and 8%, respectively, except for the inter-site CoV of R2(*) (<20%). The GM probability maps based on the MT parameter maps had a 14% higher inter-site reproducibility than maps based on conventional T1-weighted images. The low inter-site bias and variance in the parameters and derived GM probability maps confirm the high comparability of the quantitative maps across sites and time points. The reliability, short acquisition time, high resolution and the detailed insights into the brain microstructure provided by MPM makes it an efficient tool for multi-center imaging studies.

Decreasing mortality and changing patterns of causes of death in the Swiss HIV Cohort Study.

BACKGROUND: Mortality among HIV-infected persons is decreasing, and causes of death are changing. Classification of deaths is hampered because of low autopsy rates, frequent deaths outside of hospitals, and shortcomings of International Statistical Classification of Diseases and Related Health Problems (ICD-10) coding. METHODS: We studied mortality among Swiss HIV Cohort Study (SHCS) participants (1988-2010) and causes of death using the Coding Causes of Death in HIV (CoDe) protocol (2005-2009). Furthermore, we linked the SHCS data to the Swiss National Cohort (SNC) cause of death registry. RESULTS: AIDS-related mortality peaked in 1992 [11.0/100 person-years (PY)] and decreased to 0.144/100 PY (2006); non-AIDS-related mortality ranged between 1.74 (1993) and 0.776/100 PY (2006); mortality of unknown cause ranged between 2.33 and 0.206/100 PY. From 2005 to 2009, 459 of 9053 participants (5.1%) died. Underlying causes of deaths were: non-AIDS malignancies [total, 85 (19%) of 446 deceased persons with known hepatitis C virus (HCV) status; HCV-negative persons, 59 (24%); HCV-coinfected persons, 26 (13%)]; AIDS [73 (16%); 50 (21%); 23 (11%)]; liver failure [67 (15%); 12 (5%); 55 (27%)]; non-AIDS infections [42 (9%); 13 (5%); 29 (14%)]; substance use [31 (7%); 9 (4%); 22 (11%)]; suicide [28 (6%); 17 (7%), 11 (6%)]; myocardial infarction [28 (6%); 24 (10%), 4 (2%)]. Characteristics of deceased persons differed in 2005 vs. 2009: median age (45 vs. 49 years, respectively); median CD4 count (257 vs. 321 cells/μL, respectively); the percentage of individuals who were antiretroviral therapy-naïve (13 vs. 5%, respectively); the percentage of deaths that were AIDS-related (23 vs. 9%, respectively); and the percentage of deaths from non-AIDS-related malignancies (13 vs. 24%, respectively). Concordance in the classification of deaths was 72% between CoDe and ICD-10 coding in the SHCS; and 60% between the SHCS and the SNC registry. CONCLUSIONS: Mortality in HIV-positive persons decreased to 1.33/100 PY in 2010. Hepatitis B or C virus coinfections increased the risk of death. Between 2005 and 2009, 84% of deaths were non-AIDS-related. Causes of deaths varied according to data source and coding system.

Probing Rad51-DNA interactions by changing DNA twist.

In eukaryotes, Rad51 protein is responsible for the recombinational repair of double-strand DNA breaks. Rad51 monomers cooperatively assemble on exonuclease-processed broken ends forming helical nucleo-protein filaments that can pair with homologous regions of sister chromatids. Homologous pairing allows the broken ends to be reunited in a complex but error-free repair process. Rad51 protein has ATPase activity but its role is poorly understood, as homologous pairing is independent of adenosine triphosphate (ATP) hydrolysis. Here we use magnetic tweezers and electron microscopy to investigate how changes of DNA twist affect the structure of Rad51-DNA complexes and how ATP hydrolysis participates in this process. We show that Rad51 protein can bind to double-stranded DNA in two different modes depending on the enforced DNA twist. The stretching mode is observed when DNA is unwound towards a helical repeat of 18.6 bp/turn, whereas a non-stretching mode is observed when DNA molecules are not permitted to change their native helical repeat. We also show that the two forms of complexes are interconvertible and that by enforcing changes of DNA twist one can induce transitions between the two forms. Our observations permit a better understanding of the role of ATP hydrolysis in Rad51-mediated homologous pairing and strand exchange.

Second-order parameter estimation

This work provides a general framework for the design of second-order blind estimators without adopting anyapproximation about the observation statistics or the a prioridistribution of the parameters. The proposed solution is obtainedminimizing the estimator variance subject to some constraints onthe estimator bias. The resulting optimal estimator is found todepend on the observation fourth-order moments that can be calculatedanalytically from the known signal model. Unfortunately,in most cases, the performance of this estimator is severely limitedby the residual bias inherent to nonlinear estimation problems.To overcome this limitation, the second-order minimum varianceunbiased estimator is deduced from the general solution by assumingaccurate prior information on the vector of parameters.This small-error approximation is adopted to design iterativeestimators or trackers. It is shown that the associated varianceconstitutes the lower bound for the variance of any unbiasedestimator based on the sample covariance matrix.The paper formulation is then applied to track the angle-of-arrival(AoA) of multiple digitally-modulated sources by means ofa uniform linear array. The optimal second-order tracker is comparedwith the classical maximum likelihood (ML) blind methodsthat are shown to be quadratic in the observed data as well. Simulationshave confirmed that the discrete nature of the transmittedsymbols can be exploited to improve considerably the discriminationof near sources in medium-to-high SNR scenarios.

Monte Carlo Methods in Parameter Estimation of Nonlinear Models

Yksi keskeisimmistä tehtävistä matemaattisten mallien tilastollisessa analyysissä on mallien tuntemattomien parametrien estimointi. Tässä diplomityössä ollaan kiinnostuneita tuntemattomien parametrien jakaumista ja niiden muodostamiseen sopivista numeerisista menetelmistä, etenkin tapauksissa, joissa malli on epälineaarinen parametrien suhteen. Erilaisten numeeristen menetelmien osalta pääpaino on Markovin ketju Monte Carlo -menetelmissä (MCMC). Nämä laskentaintensiiviset menetelmät ovat viime aikoina kasvattaneet suosiotaan lähinnä kasvaneen laskentatehon vuoksi. Sekä Markovin ketjujen että Monte Carlo -simuloinnin teoriaa on esitelty työssä siinä määrin, että menetelmien toimivuus saadaan perusteltua. Viime aikoina kehitetyistä menetelmistä tarkastellaan etenkin adaptiivisia MCMC menetelmiä. Työn lähestymistapa on käytännönläheinen ja erilaisia MCMC -menetelmien toteutukseen liittyviä asioita korostetaan. Työn empiirisessä osuudessa tarkastellaan viiden esimerkkimallin tuntemattomien parametrien jakaumaa käyttäen hyväksi teoriaosassa esitettyjä menetelmiä. Mallit kuvaavat kemiallisia reaktioita ja kuvataan tavallisina differentiaaliyhtälöryhminä. Mallit on kerätty kemisteiltä Lappeenrannan teknillisestä yliopistosta ja Åbo Akademista, Turusta.

Tukkilajittelun röntgenmittauksen hyödyntäminen, tapaus Korkeakosken saha

Diplomityön tavoitteena oli selvittää työn toimeksiantajan UPM, Korkeakosken sahan röntgenmittauslaitteen oksaindeksilajitteluparametrille lukuarvo, jolla päästään A-tukkien osalta tavoiteltuun sydänsahatavaralaatujakaumaan eli saadaan siirrettyä VI- sydänsahatavaralaatu B-tukkien joukkoon. Lisäksi työssä tutkittiin sahan tukkilajittelun röntgenmittauslaitteen mittauksen toimivuutta ja sen tehokkaampaa hyödyntämistä. Korkeakosken sahan käyttämä röntgenmittauslaite on Bintec Oy:n kehittämä ja on tyypiltään Wood-X-4D. Laitteen mittaus perustuu tukin kuvaamiseen viipaleinaeli tomografiamittaukseen. Laite mittaa tukista useita ominaisuuksia ja antaa niiden perusteella lajitteluparametreille lukuarvoja. Lajitteluparametriarvojen muuttaminen vaikuttaa syntyvään sydänsahatavaralaatujakaumaan. Työ suoritettiin röntgenmittauslaitteella tekemällä tukeille toistomittauksia ja lajittelukokeita. Kokeissa käytettävät tukit olivat halkaisijaltaan 230 mm - tukkiluokasta. Tukkeja lajiteltiin eri tukkilaatulajitteluasetuksilla, jolloin seurattiin niistä sahattavia sahatavaralaatuja. Sahatavaralaatujen määrityksessä käytettiin sahaosastolla olevaa Finscan Oy:n kehittämää BoardMaster-NT-lajittelumittalaitetta. Tutkimus osoitti, että oksaindeksin pudottamisella, ei päästy työnantajan asettamaan sydänsahatavaran laatulajittelutavoitteeseen sallituissa oksaindeksirajoissa. Tavoitteen saavuttaminen olisi edellyttänyt oksaindeksin arvon pudottamista selkeästi alle asetetun 28 rajan. Tutkimustulokset osoittivat, että röntgenmittalaitteen lajitteluparametrien toiminnan varmuus vaihteli merkittävästi riippuen käytettävästä parametrista ja että laitteen mittaustarkkuus kärsi laitteen yleiseksi viaksi todetun detektorivian myötä. Täten tarkka laatulajittelu edellyttää röntgenmittalaitteen kaikkia neljää toimivaa detektoria. Tämä pystytään varmistamaanvaradetektorilla.

Planning and control of internal development projects in a fast changing environment: Case study

Tutkimuksen tarkoituksena on kuvata ja ymmärtää kuinka sisäisiä kehityshankkeita voidaan hallita onnistuneesti kun toimitaan nopeasti muuttuvassa ympäristössä. Tutkimus kuvailee etenkin projekteille tärkeitä menestymistekijöitä, kuten suunnittelu, kontrollointi ja päätöksenteko. Tutkimus selvittää yleisimmät ongelma-alueet case-organisaation sisäisten kehityshankkeiden hallinnassa. Tutkimus on luonteeltaan laadullinen tutkimus, jossa tutkimusmenetelmänä on käytetty tapaustutkimusta. Empiirisessa osassa käsittellään case-organisaation sisäisiä informaatioteknologia-hankkeita (IT) ja uusien konseptien kehityshankkeita (NCD). iSisäisten kehityshankkeiden erilaisuuden ymmärtäminen oli tutkimuksen tärkein tulos. Tutkimuksen empiirinen osio osoitti sen, että epävarmuudella on erittäin suuri vaikutus projektihallintaan sekä projektin kontrollointiin. Case-organisaation IT-projektien onnistuminen riippuu organisaatiomuu-toksen onnistumisesta. Asiakkaisiin ja markkinoihin liittyvät epävarmuudet ovat vaikuttavimmat NCD projektien epävarmuuksista. Näillä epävarmuuk-sil­la on vaikutusta projektihallintaan jonka myötä NCD projektit juuttuvat useim­mi­ten noidankehiin tai ne lopetetaan jo aikaisessa vaiheessa.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

The changing milliarcsecond radio morphology of the gamma-ray binary LS 5039

LS 5039 is one of the few TeV emitting X-ray binaries detected so far. The powering source of its multiwavelength emission can be accretion in a microquasar scenario or wind interaction in a young nonaccreting pulsar scenario. Aims.To present new high-resolution radio images and compare them with the expected behavior in the different scenarios. Methods.We analyze Very Long Baseline Array (VLBA) radio observations that provide morphological and astrometric information at milliarcsecond scales. Results.We detect a changing morphology between two images obtained five days apart. In both runs there is a core component with a constant flux density, and an elongated emission with a position angle (PA) that changes by 12 $\pm$ $3\degr$ between both runs. The source is nearly symmetric in the first run and asymmetric in the second one. The astrometric results are not conclusive. Conclusions.A simple and shockless microquasar scenario cannot easily explain the observed changes in morphology. An interpretation within the young nonaccreting pulsar scenario requires the inclination of the binary system to be very close to the upper limit imposed by the absence of X-ray eclipses.

The membrane-permeable calmodulin inhibitors (W-7/W-13) bind to membranes changing the electrostatic surface potential. Dual effect of W-13 on EGFR activation

Membrane-permeable calmodulin inhibitors, such as the napthalenesulfonamide derivatives W-7/W-13, trifluoperazine, and calmidazolium, are used widely to investigate the role of calcium/calmodulin (Ca2+/CaM) in living cells. If two chemically different inhibitors (e.g. W-7 and trifluoperazine) produce similar effects, investigators often assume the effects are due to CaM inhibition. Zeta potential measurements, however, show that these amphipathic weak bases bind to phospholipid vesicles at the same concentrations as they inhibit Ca 2 /CaM; this suggests that they also bind to the inner leaflet of the plasma membrane, reducing its negative electrostatic surface potential. This change will cause electrostatically bound clusters of basic residues on peripheral (e.g. Src and K-Ras4B) and integral (e.g. epidermal growth factor receptor (EGFR)) proteins to translocate from the membrane to the cytoplasm. We measured inhibitor-mediated translocation of a simple basic peptide corresponding to the calmodulin-binding juxtamembrane region of the EGFR on model membranes; W-7/W-13 causes translocation of this peptide from membrane to solution, suggesting that caution must be exercised when interpreting the results obtained with these inhibitors in living cells. We present evidence that they exert dual effects on autophosphorylation of EGFR;W-13 inhibits epidermal growth factordependent EGFR autophosphorylation under different experimental conditions, but in the absence of epidermal growth factor, W-13 stimulates autophosphorylation of the receptor in four different cell types. Our interpretation is that the former effect is due toW-13inhibition of Ca 2 /CaM, but thelatter results could be due to binding of W-13 to the plasma membrane.