Determination of trace level microcystins in water using solid-phase extraction and high performance liquid chromatography

This paper presents a method for trace level analysis of microcystins in water using solid-phase extraction and high performance liquid chromatography. The optimized condition enabled the determination of common microcystins at levels as low as 0.02 similar to 0.05 mug/L, and the liner range is from 0.1 mug/L to 50 mug/L. The method has been applied to the analysis of field sample from Dianchi lake.

In(Ga)As/GaAs自组织量子点激光器的研究

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

InN薄膜的三维生长及其对材料性质的影响

Submitted by zhangdi (zhangdi@red.semi.ac.cn) on 2009-04-13T11:45:31Z

High efficiency and broad bandwidth grating coupler between nanophotonic waveguide and fibre

A high efficiency and broad bandwidth grating coupler between a silicon-on-insulator (SOI) nanophotonic waveguide and fibre is designed and fabricated. Coupling efficiencies of 46% and 25% at a wavelength of 1.55 mu m are achieved by simulation and experiment, respectively. An optical 3 dB bandwidth of 45 nm from 1530 nm to 1575 nm is also obtained in experiment. Numerical calculation shows that a tolerance to fabrication error of 10 nm in etch depth is achievable. The measurement results indicate that the alignment error of +/-2 mu m results in less than 1 dB additional coupling loss.

Enhancement of quality factor for TE whispering-gallery modes in microcylinder resonators

The enhancement of quality factor for TE whispering-gallery modes is analyzed for three-dimensional microcylinder resonators based on the destructive interference between vertical leakage modes. In the microcylinder resonator, the TE whispering-gallery modes can couple with vertical propagation modes, which results in vertical radiation loss and low quality factors. However, the vertical loss can be canceled by choosing appropriate thickness of the upper cladding layer or radius of the microcylinder. A mode quality factor increase by three orders of magnitude is predicted by finite-difference time-domain simulation. Furthermore, the condition of vertical leakage cancellation is analyzed.

Mode Analysis and Design of a Low-Loss Photonic Crystal 60 degrees Waveguide Bend

The guided modes of a two-dimensional photonic crystal straight waveguide and a waveguide bend are studied in order to find the high transmission mechanism for the waveguide bend. We find that high transmission occurs when the mode patterns and wave numbers match, while the single-mode condition in the waveguide bend is not necessarily required. According to the mechanism, a simply modified bend structure with broad high transmission band is proposed. The bandwidth is significantly increased from 19 to 116 nm with transmission above 90%, and covers the entire C band of optical communication.

High transmission of slow light in the photonic crystal waveguide bends

We present the research on the transmission characteristic of slow-light-mode in the photonic crystal line-defect waveguide bends on SOL After optimizing the structure parameters in the vicinity of the bends, the normalized transmission efficiency of slow-light-mode through the photonic crystal 60 degree and 120 degree waveguide bends are as high as 80% and 60% respectively, which are 10 times higher than that in the undeformed case. To slow down light further, we design novel coupled cavity waveguide bend structures with high quality-factor. High normalized transmission efficiency of 75% and low group velocity of c/170 ( c is the light velocity in vacuum) are realized. These results are beneficial to enhance the slow light effect of photonic crystal structures and improve the miniaturization and integration of photonic crystal slow light devices.

The impact of imperfect symmetry on band edge modes of a two-dimensional photonic crystal with square lattice

A theoretical analysis has been performed by means of the plane-wave expansion method to examine the dispersion properties of photons at high symmetry points of an InP based two-dimensional photonic crystal with square lattice. The Q factors are compared qualitatively. The mechanism of surface-emitting is due to the photon manipulation by periodic dielectric materials in terms of Bragg diffraction. A surface-emitting photonic crystal resonator is designed based on the phenomenon of slow light. Photonic crystal slabs with different unit cells are utilized in the simulation. The results indicate that the change of the air holes can affect the polarization property of the modes. So we can find a way to improve the polarization by reducing the symmetry of the structure.

High efficiency operation of butt joint line-defect-waveguide microlaser in two-dimensional photonic crystal slab

Butt joint line-defect-waveguide microlasers are demonstrated on photonic crystal slabs with airholes in a triangular lattice. Such microlaser is designed to increase the output power from the waveguide edge directly. The output power is remarkably enhanced to 214 times higher by introducing chirped structure in the output waveguide. The lasing mode operates in the linear dispersion region of the output waveguide so that the absorption loss due to the band-edge effect is reduced. The laser resonance is illustrated theoretically using the finite difference time domain method. A practical high power efficiency of 20% is obtained in this microlaser. (C) 2008 American Institute of Physics.

Electroluminescence from nano-crystalline Si/SiO2 structures embedded in pn junctions

Phosphorous-doped and boron-doped amorphous Si thin films as well as amorphous SiO2/Si/SiO2 sandwiched structures were prepared in a plasma enhanced chemical vapor deposition system. Then, the p-i-n structures containing nano-crystalline Si/SiO2 sandwiched structures as the intrinsic layer were prepared in situ followed by thermal annealing. Electroluminescence spectra were measured at room temperature under forward bias, and it is found that the electroluminescence intensity is strongly influenced by the types of substrate. The turn-on voltages can be reduced to 3 V for samples prepared on heavily doped p-type Si (p(+)-Si) substrates and the corresponding electroluminescence intensity is more than two orders of magnitude stronger than that on lightly doped p-type Si (p-Si) and ITO glass substrates. The improvements of light emission can be ascribed to enhanced hole injection and the consequent recombination of electron-hole pairs in the luminescent nanocrystalline Si/SiO2 system. (C) 2008 Elsevier Ltd. All rights reserved.

Design of a compact polarization beam splitter based on a deformed photonic crystal directional coupler

In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric (TE) guided mode and transverse-magnetic (TM) guided mode are split due to different guiding mechanisms. The effect of the shape deformation of the air holes on the coupler is studied. It discovered that the coupling strength of the coupled waveguides is strongly enhanced by introducing elliptical airholes, which reduce the device length to less than 18.5 mu m. A finite-difference time-domain simulation is performed to evaluate the performance of the device, and the extinction ratios for both TE and TM polarized light are higher than 20 dB.

Design, fabrication and characterization of a high-performance microring resonator in silicon-on-insulator

A high-performance microring resonator in a silicon-on-insulator rib waveguide is realized by using the electron beam lithography followed by inductively coupled plasma etching. The design and the experimental realization of this device are presented in detail. In addition to improving relevant processes to minimize propagation loss, the coupling efficiency between the ring and the bus is carefully chosen to approach a critical coupling for high performance operating. We have measured a quality factor of 21,200 and an extinction ratio of 12.5dB at a resonant wavelength of 1549.32nm. Meanwhile, a low propagation loss of 0.89dB/mm in a curved waveguide with a bending radius of 40 mu m is demonstrated as well.

Application of fast Pade approximation in simulating photonic crystal nanocavities by FDTD technology

The exact calculation of mode quality factor Q is a key problem in the design of high-Q photonic crystal nanocavity. On the basis of further investigation on conventional Pade approximation, FDM and DFT, Pade approximation with Baker's algorithm is enhanced through introducing multiple frequency search and parabola interpolation. Though Pade approximation is a nonlinear signal processing method and only short time sequence is needed, we find the different length of sequence requirements for 2D and 3D FDTD, which is very important to obtain convergent and accurate results. By using the modified Pade approximation method and 3D FDTD, the 2D slab photonic crystal nanocavity is analyzed and high-Q multimode can be solved quickly instead of large range high-resolution scanning. Monitor position has also been investigated. These results are very helpful to the design of photonic crystal nanocavity devices. (C) 2008 Elsevier B.V. All rights reserved.

Dispersion-compensating photonic crystal fibers with special characteristics

Based on the modified dual core structure, three kinds of special photonic crystal fibers are presented, which are extremely large negative dispersion, super-broad bond, and large area made field dispersion-compensating photonic crystal fibers (DCPCF). For extremely large negative dispersion DCPCF, the peak of negative dispersion reaches -5.9 x 10(4) ps/(mn km). Super-broad bond DCPCF has broadband large negative dispersion and the dispersion value varies linearly from -380 ps/(nm km) to -420 ps/(nm km) in the C band. The designed large area made field DCPCF has a peak dispersion of -1203 ps/(nm km) with the inner core mode area of 47 mu m(2) and outer core mode area of 835 mu m(2). Furthermore, for the large area mode field DCPCF, the experimental result is also obtained. (C) 2008 Wiley Periodicals, Inc.

Room-temperature photonic crystal laser in H3 cavity on InGaAsP/InP slab

We fabricate and investigate two-dimensional photonic crystal H3 microcavities in an InGaAsP slab. The lasing action at room temperature is observed. The lasering threshold is 7mW under the pulsed pump of 0.75% duty cycle. The Q factor and the lasing mode characteristics are simulated by three-dimensional finite difference time domain method. The simulation result matches well with the experiment.