Comparison of physical properties of two exogenous surfactants: new parameter.

The pulmonary surfactant has essential physical properties for normal lung function. The most important property is the surface tension. In this work, it was evaluated the surface tension of two commercial exogenous surfactants used in surfactant replacement therapy, poractant alfa (Curosurf, Chiesi Farmaceuticals, Italy) and beractant (Survanta, Abbott Laboratories, USA) using new parameters. A Langmuir film balance (Minitrough, KSV Instruments, Finland) was used to measure surface tension of poractant alfa and beractant samples. For both samples, we prepared a solution of 1 mg/m dissolved in chloroform (100π`), which was applied over a subphase of milli-Q water (175 ml) in the chamber of the balance. The chamber has two moving barriers that can change its surface area between a maximal value of 112.5 cm 2 , and a minimal value of 22.5 cm 2, defining a balance cycle. Each surfactant had its surface tension evaluated during 20 balance cycles for three times. Four quantities were calculated from the experiment: Minimum Surface Tension (MTS), defined as the surface tension at minimal surface area during the first cycle; Mean Work Cycle (MWC), defined as the mean hysteresis area of the measured surface tension curve of the last 16 balance cycles; Critical Active Surface Area in Compression (CASAC) or in Expansion (CASAE), defined as the maximal chamber area where the surfactant is active on the surface in compression or expansion. The t-test was applied to verify for statistical significance of the results. Comproved with the MST is the same reported in literature, the differences between MWC, CASAC, and CASAE were statistically significant (p<0.001). The MWC, CASAC and CASAE were higher for poractant alfa than for beractant. A higher MWC for poractant alfa means higher elastic recoil of the lung in comparison with beractant. Using a different methodology, our results showed that poractant alfa is probably more effective in a surfactant replacement therapy than beractant due the use of poractant alfa in relation to the use of beractant in preterm infants with Respiratory Distress Syndrome (RDS).

Mechanical Measurements Of Two Exogenous Surfactants Using A Langmuir Film Balance:A Comparative Study

Rationale: The primary function of surfactant is to reduce the surface tension at air-liquid interface. In this study, the surface tension behavior of two commercial surfactants, poractant alfa (ChiesiFarmaceuticals,ltaly) and beractant (Abbott Laboratories,USA), were evaluated,using new parameters. Methods: We used a Langmuir film balance (Minitrough,KSV lnstruments,Finland) to measure of surface tension of both poractant alfa and beractant samples. For both samples,we prepared a solution of 1 mg/mdl dissolved in chloroform. The solution (1uL) was applied over a subphase of milli-Q water (175 ml) in the chamber of the balance. The chamber has two moving barriers that can change its surface area between a maximum value of 112.5 cm2 anda minimum value of 22.5 cm2, defining a balance cycle.lhree sample's films were evaluated for each sample, during 20 balance cycles. Here quantify two new variables, which is the mean hysteresis area of the measured curve surface tension of the last 16 balance cycles,defined here as Mean Work Cycle (MWC), and the moment that the surfactant is active in the surface, this measure is defined here as Active Surface Area Critical in the compression (ASACC) and the expansion (ASACE). The test was applied to compare the statistical significance of the results.

Ferroelektrische Netzwerksynthese und ihre Charakterisierung

Deutsch:Diese Arbeit beschäftigt sich zum einen mit der Synthese neuer, vernetzbarer, ferroelektrischer Verbindungen, welche eine höhere spontane Polarisation und damit ein besseres Schaltverhalten nach Vernetzung aufweisen sollten. Dazu wurde in bekannte Systemen die Halogene Fluor, Chlor und Brom erfolgreich eingebaut. Desweiteren konnten neue Untersuchungmethoden für ferroelektrische, flüssigkristalline Netzwerke erfolgreich angewendet und weiterentwickelt werden. Damit gelang es z. B. neue Erkenntnisse über die elastischen Eigenschaften von LC-Elastomeren zu gewinnen, wobei es erstmalig gelang, Seifenblasen aus LC-Polymeren herzustellen und durch UV-Bestrahlung zu vernetzen. Durch die Messung des Radius in Abhängigkeit des Druckes war es möglich festzustellen, daß sich das Verhalten des Polymers, welches zunächst oberflächenspannungskontrolliert war, nach UV-Bestrahlung, in ein elastisches Verhalten änderte. Aus der Radius vs. Druckbeziehung war es möglich, Daten über die elastischen Eigenschaften zu erhalten. Die Ballone zeigten dabei typische, gummielastische Eigenschaften. Ein Einfluß der Mesophase (d.h. SA oder SC-Phase) auf die Eigenschaften der Ballone konnte dabei nicht festgestellt werden. Für die beiden hier untersuchten Systeme des inter- und intralyer vernetzbaren System konnte festgestellt werden, daß ihr elastisches Verhalten sehr ähnlich ist, ganz im Gegensatz zu den früheren elektrooptischen Untersuchungen. D. h. beide Systeme zeigten nach der Vernetzung bis auf einen Faktor 2 das gleiche elastische Verhalten. Im Gegensatz zu nematischen Elastomeren, welche am Phasenübergang zum Teil große thermoelastische Änderungen zeigen, zeigten die hier untersuchten Elastomere keine Änderung der elastischen Eigenschaften beim Phasenübergang, was sich u.a. auf die relativ hohen Vernetzungsdichten zurückführen läßt. Weiterhin wurde die Elektrostriktion in ferroelektrischen flüssigkristallinen Elastomerenfilmen untersucht, welche zu einem neuen Weltrekord des elektrostriktiven Effektes führte. Es wurden Schichtdickenänderungen von 4% bei einem angelegten Feld von 1,5 kV gemessen. Röntgenstreuexperimente an gespincoateten, vernetzten Polymerfilmen haben überdies gezeigt, daß der gemessene Effekt voll und ganz auf den elektroklinen Effekt zurück zu führen ist. Zum Schluß wurde ein neuer Weg ausgearbeitet, um flüssigkristalline Netzwerke unter Einsatz von weniger präparativer Chemie zu erhalten. Dazu wurde die Möglichkeit der Netzwerkbildung mit organischen Gelbildnern untersucht. In diesem Zusammenhang ist es erstmalig gelungen, ferroelektrische Flüssigkristalle reversibel in dem einen oder anderen Zustand orientiert zu stabilisieren, wobei beliebig oft zwischen den stabilisierten Zuständen gewechselt werden konnte.

Eigenschaftskorrelationen in kolloidalen Festkörpern und Fluiden aus optischen Experimenten

Die Arbeit beschäftigt sich mit ein- und zweikomponentigen, geladenen Kolloidsystemen, die in vollentsalzten wässrigen und organischen Dispersionen kristalline Strukturen ausbilden. Im ersten Teil der Arbeit wird die Wechselwirkung der Kolloide mit verschiedenen Methoden charakterisiert. Dabei zeigten sich quantitative Übereinstimmungen zwischen den Resultaten aus Zellenmodellrechnungen und aus elektrokinetischen Messungen einerseits und Messungen des Phasenverhaltens und der Elastizität andererseits. Diese nunmehr gut gesicherten Diskrepanzen und Korrelationen bedürfen des theoretischen Verständnisses. Im zweiten Teil der Arbeit wurde das Erstarrungsverhalten kolloidaler Scherschmelzen in den kristallinen Zustand mit (zeitaufgelöster) statischer Lichtstreuung und mikroskopischen Methoden untersucht. Dies erlaubte zunächst die kritische Überprüfung klassischer Modelle zur Kristallisationskinetik (Wilson- Frenkel- Gesetz, klassische Nukleationstheorie, Kolmogorov- Johnson- Mehl- Avrami (KJMA)- Modell). Es zeigte sich, dass diese Modelle gut geeignet sind die Verfestigung auch geladener kolloidaler Schmelzen zu beschreiben, wenn die diffusive Einteilchendynamik korrekt berücksichtigt wird. Erstmals wurden Oberflächenspannungen zwischen Kristallkeim und Schmelze für geladene Systeme bestimmt, die im Gegensatz zu Hartkugel- Systemen eine lineare Zunahme mit der Partikelkonzentration aufweisen. Der Methodenpark und die Auswerteverfahren wurden sodann auf binäre kolloidale Mischungen übertragen. Entsprechend den Einzelkomponenten kristallisieren alle Mischungen in einer kubischen Struktur. Leitfähigkeitsmessungen und Elastizität stehen meist im Einklang mit der Nukleation zufallsgeordneter Substitutionskristalle. Für mehrere Proben mit unterschiedlichen Größenverhältnissen wurde mit statischer Lichtstreuung der Einfluss der Komposition und der Partikelkonzentration auf das Nukleationsverhalten untersucht. Im Allgemeinen wurde das Nukleationsszenario einkomponentiger Systeme mit einigen unerwarteten, quantitativen Unterschieden reproduziert. Für eine Probe, die eine Kompositionsordnung andeutet, wurden interessante Korrelationen zwischen der Nukleationskinetik und den Eigenschaften des resultierenden Festkörpers gefunden.

Mechanische Eigenschaften von freitragenden artifiziellen und nativen Membranen

This thesis presents a new method to explore the local mechanical properties such as bending modulus or surface tension of artificial and native pore-spanning membranes. Therefore the elastic response of a free-standing membrane to a local indentation by the means of atomic force microscopy is measured. Starting point are highly hexagonal ordered pores in alumina produced by electrochemical anodization of planar aluminium. The homogeneous pore radius can by tailored in the range of 10 nm up to 200 nm, but radius of 33 nm, 90 nm and 200 nm turned out to be best suited for investigation of the mechanical properties of pore-spanning native or artificial membranes. In this work artificial membrane systems consisting of DODAB as a bilayer in gel phase or DOTAP as a fluide membrane are spreaded by vesicle absorption on hexagonal structured pores after chemisorption of a 3-mercaptopropionic acid monolayer. Centrally indenting these nanodrums with an atomic force microscope tip yields force-indentation curves, which are quantitatively analyzed by solving the corresponding shape equations of continuum curvature elasticity. Since the measured response depends in a known way on the system geometry (pore size, tip radius) and on material parameters (bending modulus, lateral tension, adhesion), this opens the possibility to monitor local elastic properties of lipid membranes in a well-controlled setting. Additionally the locally distributed mechanical properties of pore-spanning artificial membranes are compared to those of native pore-spanning membranes. Therefore the basal membrane of MDCK II cells was prepared on porous alumina assays and their mechanical properties were analyzed by means of atomic force microscopy. Finally the elastic behavior such as the Young modulus of living MDCK II cells under various osmotic pressures is investigated. By changing the osmolarity in the extracellular region of MDCK II cells a volume change is induced according to hydration and dehydration of the cells, respectively. This volume change induces also a change in the elastic behavior of the cell, which is quantified by the means of force spectroscopy.

CFD modeling of two-phase boiling flows in the slug flow regime with an interface capturing technique

The objective of this thesis was to improve the commercial CFD software Ansys Fluent to obtain a tool able to perform accurate simulations of flow boiling in the slug flow regime. The achievement of a reliable numerical framework allows a better understanding of the bubble and flow dynamics induced by the evaporation and makes possible the prediction of the wall heat transfer trends. In order to save computational time, the flow is modeled with an axisymmetrical formulation. Vapor and liquid phases are treated as incompressible and in laminar flow. By means of a single fluid approach, the flow equations are written as for a single phase flow, but discontinuities at the interface and interfacial effects need to be accounted for and discretized properly. Ansys Fluent provides a Volume Of Fluid technique to advect the interface and to map the discontinuous fluid properties throughout the flow domain. The interfacial effects are dominant in the boiling slug flow and the accuracy of their estimation is fundamental for the reliability of the solver. Self-implemented functions, developed ad-hoc, are introduced within the numerical code to compute the surface tension force and the rates of mass and energy exchange at the interface related to the evaporation. Several validation benchmarks assess the better performances of the improved software. Various adiabatic configurations are simulated in order to test the capability of the numerical framework in modeling actual flows and the comparison with experimental results is very positive. The simulation of a single evaporating bubble underlines the dominant effect on the global heat transfer rate of the local transient heat convection in the liquid after the bubble transit. The simulation of multiple evaporating bubbles flowing in sequence shows that their mutual influence can strongly enhance the heat transfer coefficient, up to twice the single phase flow value.

Monte-Carlo simulation of hard spherocylinders under confinement

When a liquid crystal is confined to a cavity its director field becomes subject to competing forces: on the one hand, the surface of the cavity orients the director field (``surface anchoring''), on the other hand deformations of the director field cost elastic energy. Hence the equilibrium director field is determined by a compromise between surface anchoring and elasticity. One example of a confined liquid crystal that has attracted particular interest from physicists is the nematic droplet. In this thesis a system of hard rods is considered as the simplest model for nematic liquid crystals consisting of elongated molecules. First, systems of hard spherocylinders in a spherical geometry are investigated by means of canonical Monte Carlo simulations. In contrast to previous simulation work on this problem, a continuum model is used. In particular, the effects of ordering near hard curved walls are studied for the low-density regime. With increasing density, first a uniaxial surface film forms and then a biaxial surface film, which eventually fills the entire cavity. We study how the surface order, the adsorption and the shape of the director field depend on the curvature of the wall. We find that orientational ordering at a curved wall in a cavity is stronger than at a flat wall, while adsorption is weaker. For densities above the isotropic-nematic transition, we always find bipolar configurations. As a next step, an extension of the Asakura-Oosawa-Vrij model for colloid-polymer mixtures to anisotropic colloids is considered. By means of computer simulations we study how droplets of hard, rod-like particles optimize their shape and structure under the influence of the osmotic compression caused by the presence of spherical particles that act as depletion agents. At sufficiently high osmotic pressures the rods that make up the drops spontaneously align to turn them into uniaxial nematic liquid crystalline droplets. The nematic droplets or ``tactoids'' that so form are not spherical but elongated, resulting from the competition between the anisotropic surface tension and the elastic deformation of the director field. In agreement with recent theoretical predictions we find that sufficiently small tactoids have a uniform director field, whilst large ones are characterized by a bipolar director field. From the shape and director-field transformation of the droplets we estimate the surface anchoring strength.

Patterns in and kinetics of phase separation in binary mixtures

This work focused mainly on two aspects of kinetics of phase separation in binary mixtures. In the first part, we studied the interplay of hydrodynamics and the phase separation of binary mixtures. A considerably flat container (a laterally extended geometry), at an aspect ratio of 14:1 (diameter: height) was chosen, so that any hydrodynamic instabilities, if they arise, could be tracked. Two binary mixtures were studied. One was a mixture of methanol and hexane, doped with 5% ethanol, which phase separated under cooling. The second was a mixture of butoxyethanol and water, doped with 2% decane, which phase separated under heating. The dopants were added to bring down the phase transition temperature around room temperature.rnrnAlthough much work has been done already on classical hydrodynamic instabilities, not much has been done in the understanding of the coupling between phase separation and hydrodynamic instabilities. This work aimed at understanding the influence of phase separation in initiating any hydrodynamic instability, and also vice versa. Another aim was to understand the influence of the applied temperature protocol on the emergence of patterns characteristic to hydrodynamic instabilities. rnrnOn slowly cooling the system continuously, at specific cooling rates, patterns were observed in the first mixture, at the start of phase separation. They resembled the patterns observed in classical Rayleigh-Bénard instability, which arises when a liquid continuously is heated from below. To suppress this classical convection, the cooling setup was tuned such that the lower side of the sample always remained cooler by a few millikelvins, relative to the top. We found that the nature of patterns changed with different cooling rates, with stable patterns appearing for a specific cooling rate (1K/h). On the basis of the cooling protocol, we estimated a modified Rayleigh number for our system. We found that the estimated modified Rayleigh number is near the critical value for instability, for cooling rates between 0.5K/h and 1K/h. This is consistent with our experimental findings. rnrnThe origin of the patterns, in spite of the lower side being relatively colder with respect to the top, points to two possible reasons. 1) During phase separation droplets of either phases are formed, which releases a latent heat. Our microcalorimetry measurements show that the rise in temperature during the first phase separation is in the order of 10-20millikelvins, which in some cases is enough to reverse the applied temperature bias. Thus phase separation in itself initiates a hydrodynamic instability. 2) The second reason comes from the cooling protocol itself. The sample was cooled from above and below. At sufficiently high cooling rates, there are situations where the interior of the sample is relatively hotter than both top and bottom of the sample. This is sufficient to create an instability within the cell. Our experiments at higher cooling rates (5K/h and above) show complex patterns, which hints that there is enough convection even before phase separation occurs. Infact, theoretical work done by Dr.Hayase show that patterns could arise in a system without latent heat, with symmetrical cooling from top and bottom. The simulations also show that the patterns do not span the entire height of the sample cell. This is again consistent with the cell sizes measured in our experiment.rnrnThe second mixture also showed patterns at specific heating rates, when it was continuously heated inducing phase separation. In this case though, the sample was turbid for a long time until patterns appeared. A meniscus was most probably formed before the patterns emerged. We attribute the reason of patterns in this case to Marangoni convection, which is present in systems with an interface, where local differences in surface tension give rise to an instability. Our estimates for the Rayleigh number also show a significantly lower number than that's required for RB-type instability.rnrnIn the first part of the work, therefore, we identify two different kinds of hydrodynamic instabilities in two different mixtures. Both are observed during, or after the first phase separation. Our patterns compare with the classical convection patterns, but here the origins are from phase separation and the cooling protocol.rnrnIn the second part of the work, we focused on the kinetics of phase separation in a polymer solution (polystyrene and methylcyclohexane), which is cooled continuously far down into the two phase region. Oscillations in turbidity, denoting material exchange between the phases are seen. Three processes contribute to the phase separation: Nucleation of droplets, their growth and coalescence, and their subsequent sedimentation. Experiments in low molecular binary mixtures had led to models of oscillation [43] which considered sedimentation time scales much faster than the time scales of nucleation and growth. The size and shape of the sample therefore did not matter in such situations. The oscillations in turbidity were volume-dominated. The present work aimed at understanding the influence of sedimentation time scales for polymer mixtures. Three heights of the sample with same composition were studied side by side. We found that periods increased with the sample height, thus showing that sedimentation time determines the period of oscillations in the polymer solutions. We experimented with different cooling rates and different compositions of the mixture, and we found that periods are still determined by the sample height, and therefore by sedimentation time. rnrnWe also see that turbidity emerges in two ways; either from the interface, or throughout the sample. We suggest that oscillations starting from the interface are due to satellite droplets that are formed on droplet coalescence at the interface. These satellite droplets are then advected to the top of the sample, and they grow, coalesce and sediment. This type of an oscillation wouldn't require the system to pass the energy barrier required for homogenous nucleation throughout the sample. This mechanism would work best in sample where the droplets could be effectively advected throughout the sample. In our experiments, we see more interface dominated oscillations in the smaller cells and lower cooling rates, where droplet advection is favourable. In larger samples and higher cooling rates, we mostly see that the whole sample becomes turbid homogenously, which requires the system to pass the energy barrier for homogenous nucleation.rnrnOscillations, in principle, occur since the system needs to pass an energy barrier for nucleation. The height of the barrier decreases with increasing supersaturation, which in turn is from the temperature ramp applied. This gives rise to a period where the system is clear, in between the turbid periods. At certain specific cooling rates, the system can follow a path such that the start of a turbid period coincides with the vanishing of the last turbid period, thus eliminating the clear periods. This means suppressions of oscillations altogether. In fact we experimentally present a case where, at a certain cooling rate, oscillations indeed vanish. rnrnThus we find through this work that the kinetics of phase separation in polymer solution is different from that of a low molecular system; sedimentation time scales become relevant, and therefore so does the shape and size of the sample. The role of interface in initiating turbid periods also become much more prominent in this system compared to that in low molecular mixtures.rnrnIn summary, some fundamental properties in the kinetics of phase separation in binary mixtures were studied. While the first part of the work described the close interplay of the first phase separation with hydrodynamic instabilities, the second part investigated the nature and determining factors of oscillations, when the system was cooled deep into the two phase region. Both cases show how the geometry of the cell can affect the kinetics of phase separation. This study leads to further fundamental understandings of the factors contributing to the kinetics of phase separation, and to the understandings of what can be controlled and tuned in practical cases. rn

Dynamic wetting of complex liquids

A simple dependency between contact angle θ and velocity or surface tension has been predicted for the wetting and dewetting behavior of simple liquids. According to the hydrodynamic theory, this dependency was described by Cox and Voinov as θ ∼ Ca^(1/3) (Ca: Capillary number). For more complex liquids like surfactant solutions, this prediction is not directly given.rnHere I present a rotating drum setup for studying wetting/dewetting processes of surfactant solutions on the basis of velocity-dependent contact angle measurements. With this new setup I showed that surfactant solutions do not follow the predicted Cox-Voinov relation, but showed a stronger contact angle dependency on surface tension. All surfactants independent of their charge showed this difference from the prediction so that electrostatic interactions as a reason could be excluded. Instead, I propose the formation of a surface tension gradient close to the three-phase contact line as the main reason for the strong contact angle decrease with increasing surfactant concentration. Surface tension gradients are not only formed locally close to the three-phase contact line, but also globally along the air-liquid interface due to the continuous creation/destruction of the interface by the drum moving out of/into the liquid. By systematically hindering the equilibration routes of the global gradient along the interface and/or through the bulk, I was able to show that the setup geometry is also important for the wetting/dewetting of surfactant solutions. Further, surface properties like roughness or chemical homogeneity of the wetted/dewetted substrate influence the wetting/dewetting behavior of the liquid, i. e. the three-phase contact line is differently pinned on rough/smooth or homogeneous/inhomogeneous surfaces. Altogether I showed that the wetting/dewetting of surfactant solutions did not depend on the surfactant type (anionic, cationic, or non-ionic) but on the surfactant concentration and strength, the setup geometry, and the surface properties.rnSurfactants do not only influence the wetting/dewetting behavior of liquids, but also the impact behavior of drops on free-standing films or solutions. In a further part of this work, I dealt with the stability of the air cushion between drop and film/solution. To allow coalescence between drop and substrate, the air cushion has to vanish. In the presence of surfactants, the vanishing of the air is slowed down due to a change in the boundary condition from slip to no-slip, i. e. coalescence is suppressed or slowed down in the presence of surfactant.

Experimentelle Untersuchung von Phasenübergängen im kolloidalen Modellsystem harter Kugeln

Die vorliegende Arbeit behandelt den fluid-kristallinen Phasenübergang sowie den Glasübergang anhand von kolloidalen Hart-Kugel(HK)-Modellsystemen. Die Untersuchungen erfolgen dabei im Wesentlichen mit unterschiedlichen Lichtstreumethoden und daher im reziproken Raum. rnDie Analyse der Kristallisationskinetik zeigt, dass es bei der Kristallisation zu signifikanten Abweichungen vom Bild der klassischen Nukleationstheorie (CNT) kommt. Diese geht von einem einstufigen Nukleationsprozess aus, wohingegen bei den hier durchgeführten Experimenten ein mehrstufiger Prozess beobachtet wird. Vor der eigentlichen Kristallisation kommt es zunächst zur Nukleation einer metastabilen Zwischenphase, sogenannter Precursor. In einer zweiten Stufe erfolgt innerhalb der Precursor die eigentliche Nukleation der Kristallite. rnDurch weitere Analyse und den Vergleich des Kristallisations- und Verglasungsszenarios konnte das Konzept der Precursornukleation auf den Vorgang der Verglasung erweitert werden. Während die Kristallnukleation oberhalb des Glasübergangspunktes zum Erliegen kommt, bleibt der Prozess der Precursornukleation auch bei verglasenden Proben erhalten. Ein Glas erstarrt somit in einem amorphen Zustand mit lokalen Precursorstrukturen. Die Korrelation der gemessenen zeitlichen Entwicklung der strukturellen sowie der dynamischen Eigenschaften zeigt darüber hinaus, dass das bisher unverstandene Ageing-Phänomen von HK-Gläsern mit der Nukleation von Precursorn zusammenhängt.rnEin solches mehrstufiges Szenario wurde bereits in früheren Veröffentlichungen beobachtet. Die im Rahmen dieser Arbeit durchgeführten Messungen ermöglichten erstmals die Bestimmung von Kristallnukleationsratendichten (Kristall-NRD) und Ratendichten für die Precursornukleation bis über den Glasübergangspunkt hinaus. Die Kristall-NRD bestätigen die Resultate aus anderen experimentellen Arbeiten. Die weiteren Analysen der Kristall-NRD belegen, dass die fluid-kristalline Grenzflächenspannung bei der Nukleation entgegen den Annahmen der CNT nicht konstant ist, sondern mit ansteigendem Volumenbruch linear zunimmt. Die Erweiterung der CNT um eine linear zunehmende Grenzflächenspannung ermöglichte eine quantitative Beschreibung der gemessenen Kristall- sowie der Precursor-NRD, was den Schluss zulässt, dass es sich in beiden Fällen um einen Boltzmann-aktivierten Prozess handelt. rnUm die beobachteten Abweichungen des Nukleationsprozesses vom Bild der CNT näher zu untersuchen, wurden die kollektiven Partikeldynamiken in stabilen Fluiden und metastabilen Schmelzen analysiert. Im klassischen Bild wird angenommen, dass die kollektive Partikeldynamik beim Vorgang der Nukleation keine Rolle spielt. Anhand der Resultate zeigen sich Abweichungen in der Dynamik stabiler Fluide und metastabiler Schmelzen. Während die kollektive Partikeldynamik in der stabilen Schmelze von der Struktur entkoppelt ist, tritt oberhalb des Phasenübergangspunktes eine Kopplung von Struktur und Dynamik auf. Dabei treten die Abweichungen zunächst in der Umgebung des ersten Strukturfaktormaximums und somit bei den am stärksten besetzten Moden auf. Mit steigender Unterkühlung nehmen die Anzahl der abweichenden Moden sowie die Stärke der Abweichungen zu. Dieses Phänomen könnte einen signifikanten Einfluss auf den Nukleationsprozess und somit auf die Kristallisationskinetik haben. Die Analyse der Dynamik im stabilen Fluid zeigt darüber hinaus Hinweise auf eine Singularität bei Annäherung an den fluid-kristallinen Phasenübergangspunkt.rnDes Weiteren wurden im Rahmen der vorliegenden Arbeit erstmals Ratendichten für die heterogene Nukleation eines HK-Systems an einer flachen Wand mittels statischer Lichtstreuung (SLS) bestimmt. Die Ergebnisse der Messung zeigen, dass die Nukleationsbarriere der heterogenen Nukleation annähernd Null ist und folglich eine vollständige Benetzung der Wand mit einer kristallinen Monolage vorliegt. Die Erweiterung der Untersuchungen auf gekrümmte Oberflächen in Form von sphärischen Partikeln (Seeds) stellt die erste experimentelle Arbeit dar, die den Einfluss eines Ensembles von Seeds auf die Kristallisationskinetik in HK-Systemen untersucht. Die Kristallisationskinetik und die Mikrostruktur werden abhängig von Größe und Anzahldichte der Seed-Partikel signifikant beeinflusst. In Übereinstimmung mit konfokalmikroskopischen Experimenten und Simulationen spielt dabei das Radienverhältnis der Majoritäts- zur Minoritätskomponente eine entscheidende Rolle.

Computer simulation methods to study interfacial tensions : from the Ising model to colloidal crystals

In condensed matter systems, the interfacial tension plays a central role for a multitude of phenomena. It is the driving force for nucleation processes, determines the shape and structure of crystalline structures and is important for industrial applications. Despite its importance, the interfacial tension is hard to determine in experiments and also in computer simulations. While for liquid-vapor interfacial tensions there exist sophisticated simulation methods to compute the interfacial tension, current methods for solid-liquid interfaces produce unsatisfactory results.rnrnAs a first approach to this topic, the influence of the interfacial tension on nuclei is studied within the three-dimensional Ising model. This model is well suited because despite its simplicity, one can learn much about nucleation of crystalline nuclei. Below the so-called roughening temperature, nuclei in the Ising model are not spherical anymore but become cubic because of the anisotropy of the interfacial tension. This is similar to crystalline nuclei, which are in general not spherical but more like a convex polyhedron with flat facets on the surface. In this context, the problem of distinguishing between the two bulk phases in the vicinity of the diffuse droplet surface is addressed. A new definition is found which correctly determines the volume of a droplet in a given configuration if compared to the volume predicted by simple macroscopic assumptions.rnrnTo compute the interfacial tension of solid-liquid interfaces, a new Monte Carlo method called ensemble switch method'' is presented which allows to compute the interfacial tension of liquid-vapor interfaces as well as solid-liquid interfaces with great accuracy. In the past, the dependence of the interfacial tension on the finite size and shape of the simulation box has often been neglected although there is a nontrivial dependence on the box dimensions. As a consequence, one needs to systematically increase the box size and extrapolate to infinite volume in order to accurately predict the interfacial tension. Therefore, a thorough finite-size scaling analysis is established in this thesis. Logarithmic corrections to the finite-size scaling are motivated and identified, which are of leading order and therefore must not be neglected. The astounding feature of these logarithmic corrections is that they do not depend at all on the model under consideration. Using the ensemble switch method, the validity of a finite-size scaling ansatz containing the aforementioned logarithmic corrections is carefully tested and confirmed. Combining the finite-size scaling theory with the ensemble switch method, the interfacial tension of several model systems, ranging from the Ising model to colloidal systems, is computed with great accuracy.

Nucleation studies on graphics processing units

Ein System in einem metastabilen Zustand muss eine bestimmte Barriere in derrnfreien Energie überwinden um einen Tropfen der stabilen Phase zu formen.rnHerkömmliche Untersuchungen nehmen hierbei kugelförmige Tropfen an. Inrnanisotropen Systemen (wie z.B. Kristallen) ist diese Annahme aber nicht ange-rnbracht. Bei tiefen Temperaturen wirkt sich die Anisotropie des Systems starkrnauf die freie Energie ihrer Oberfläche aus. Diese Wirkung wird oberhalb derrnAufrauungstemperatur T R schwächer. Das Ising-Modell ist ein einfaches Mo-rndell, welches eine solche Anisotropie aufweist. Wir führen großangelegte Sim-rnulationen durch, um die Effekte, die mit einer endlichen Simulationsbox ein-rnhergehen, sowie statistische Ungenauigkeiten möglichst klein zu halten. DasrnAusmaß der Simulationen die benötigt werden um sinnvolle Ergebnisse zu pro-rnduzieren, erfordert die Entwicklung eines skalierbaren Simulationsprogrammsrnfür das Ising-Modell, welcher auf verschiedenen parallelen Architekturen (z.B.rnGrafikkarten) verwendet werden kann. Plattformunabhängigkeit wird durch ab-rnstrakte Schnittstellen erreicht, welche plattformspezifische Implementierungs-rndetails verstecken. Wir benutzen eine Systemgeometrie die es erlaubt eine Ober-rnfläche mit einem variablen Winkel zur Kristallebene zu untersuchen. Die Ober-rnfläche ist in Kontakt mit einer harten Wand, wobei der Kontaktwinkel Θ durchrnein Oberflächenfeld eingestellt werden kann. Wir leiten eine Differenzialglei-rnchung ab, welche das Verhalten der freien Energie der Oberfläche in einemrnanisotropen System beschreibt. Kombiniert mit thermodynamischer Integrationrnkann die Gleichung benutzt werden, um die anisotrope Oberflächenspannungrnüber einen großen Winkelbereich zu integrieren. Vergleiche mit früheren Mes-rnsungen in anderen Geometrien und anderen Methoden zeigen hohe Überein-rnstimung und Genauigkeit, welche vor allem durch die im Vergleich zu früherenrnMessungen wesentlich größeren Simulationsdomänen erreicht wird. Die Temper-rnaturabhängigkeit der Oberflächensteifheit κ wird oberhalb von T R durch diernKrümmung der freien Energie der Oberfläche für kleine Winkel gemessen. DiesernMessung lässt sich mit Simulationsergebnissen in der Literatur vergleichen undrnhat bessere Übereinstimmung mit theoretischen Voraussagen über das Skalen-rnverhalten von κ. Darüber hinaus entwickeln wir ein Tieftemperatur-Modell fürrndas Verhalten um Θ = 90 Grad weit unterhalb von T R. Der Winkel bleibt bis zu einemrnkritischen Feld H C quasi null; oberhalb des kritischen Feldes steigt der Winkelrnrapide an. H C wird mit der freien Energie einer Stufe in Verbindung gebracht,rnwas es ermöglicht, das kritische Verhalten dieser Größe zu analysieren. Die harternWand muss in die Analyse einbezogen werden. Durch den Vergleich freier En-rnergien bei geschickt gewählten Systemgrößen ist es möglich, den Beitrag derrnKontaktlinie zur freien Energie in Abhängigkeit von Θ zu messen. Diese Anal-rnyse wird bei verschiedenen Temperaturen durchgeführt. Im letzten Kapitel wirdrneine 2D Fluiddynamik Simulation für Grafikkarten parallelisiert, welche u. a.rnbenutzt werden kann um die Dynamik der Atmosphäre zu simulieren. Wir im-rnplementieren einen parallelen Evolution Galerkin Operator und erreichen

Darstellung von fluorierten Amphiphilen zur Modifikation von Grenzflächeneigenschaften

Die vorliegende Arbeit behandelt die Darstellung von neuen fluorierten Amphiphilen in Hinblick auf deren spätere Anwendung zur Modifikation von flüssig-gasförmigen, flüssig-flüssigen und flüssig-festen Grenzflächen. Jedes der drei Themengebiete richtete sich an eine andere Grenzfläche. Die erste Aufgabe wurde mit der Darstellung und Charakterisierung von Fluortensiden kurzen Perfluoralkyl-Ketten erfüllt, welche als möglichen umweltfreundlichen Ersatz für die Derivate der langkettigen Perfluoroktancarbonsäure und Perfluoroktansulfonsäure Anwendung finden. Es wurden Fluortenside entwickelt, welche die Oberflächenspannung von Wasser auf bis zu 18 mN/m absenken können. Der zweite Fokus lag auf der Stabilisierung einer fluorierten Emulsion, die sich für die carbo-kationische Polymerisationen eignete. Im Rahmen der Arbeit wurde das neue Blockcopolymer Poly(isobutylen-b-pentafluorstyrol) dargestellt. Neben der Homopolymerisation von Isobutylen zur PIB-Partikelsynthese wurde die Eignung des Stabilisator-Emulsionssystems durch die Darstellung von hart-weichen PS-PIB-Hybridpartikeln erfolgreich verfolgt. Dazu wurde die Synthese von quervernetzten PS-Kernpartikeln und der anschließenden Umhüllung durch PIB in einem weiteren Schritt. Im dritten Teil wurde die Adsorption von amphiphilen Fluorpolymeren zur Solvophobierung von rauen anorganischen Oberflächen untersucht. Es konnten sowohl superhydrophobe als auch superoleophobe Eigenschaften erzielt werden.

Monte Carlo simulations of nucleation of colloidal crystals

A crystal nucleus in a finite volume may exhibit phase coexistence with a surrounding fluid. The thermodynamic properties of the coexisting fluid (pressure and chemical potential) are enhanced relative to their coexistence values. This enhancement is uniquely related to the surface excess free energy. rnA model for weakly attractive soft colloidal particles is investigated, the so called Asakura-Oosawa model. In simulations, this model allows for the calculation of the pressure in the liquid using the virial formula directly. The phase coexistence pressure in the thermodynamic limit is obtained from the interface velocity method. We introduce a method by which the chemical potential in dense liquids can be measured. There is neither a need to locate the interface nor to compute the anisotropic interfacial tension to obtain nucleation barriers. Therefore, our analysis is appropriate for nuclei of arbitrary shape. Monte Carlo simulations over a wide range of nucleus volumes yield to nucleation barriers independent from the total system volume. The interfacial tension is determined via the ensemble-switch method, hence a detailed test of classical nucleation theory is possible. The anisotropy of the interfacial tension and the resulting non-spherical shape has only a minor effect on the barrier for the Asakura-Oosawa model.

Investigation Of Leucine And Glutamic Acid Properties From The Nanoscale To The Macroscale

Aerosols are known to have important effects on climate, the atmosphere, and human health. The extent of those effects is unknown and largely depend on the interaction of aerosols with water in the atmosphere. Ambient aerosols are complex mixtures of both inorganic and organic compounds. The cloud condensation nuclei (CCN) activities, hygroscopic behavior and particle morphology of a monocarboxylic amino acid (leucine) and a dicarboxylic amino acid (glutamic acid) were investigated. Activation diameters at various supersaturation conditions were experimentally determined and compared with Köhler theoretical values. The theory accounts for both surface tension and the limited solubility of organic compounds. It was discovered that glutamic acid aerosols readily took on water both when relative humidity was less than 100% and when the supersaturation condition was reached, while leucine did not show any water activation at those conditions. Moreover, the study also suggests that Köhler theory describes CCN activity of organic compounds well when only surface tension of the compound is taken into account and complete solubility is assumed. Single parameter ¿ was also computed using both CCN data and hygroscopic growth factor (GF). The results of ¿ range from 0.17 to 0.53 using CCN data and 0.09 to 0.2 using GFs. Finally, the study suggests that during the water-evaporation/particle-nucleation process, crystallization from solution droplets takes place at different locations: for glutamic acid at the particles¿ center and leucine at the particles¿ boundary.