Numerical modeling of fiber lasers with long and ultra-long ring cavity

We highlight two important aspects related to a mathematical modeling of pulsed fiber lasers with long and ultra-long ring cavity -impact of an initial noise and a cavity length on generation of single optical pulses. Using as an example a simple scalar model of a ring fiber laser that describes the radiation build-up from noise and the following intra-cavity pulse dynamics during a round trip we study dependence of generated pulse characteristics on the resonator length in the range from 30 m up to 2 km. © 2013 Optical Society of America.

Hydrogen embrittlement contributions to fatigue crack growth in a structural steel

The detrimental effects of a hydrogen atmosphere on the fatigue resistance of BS 4360 steel have been assessed by a comparison of crack growth rates in air and hydrogen at a low cycling frequency (0.1Hz), and at a number of temperature (25, 50 and 80 °C). The crack propagation rates in air are almost independent of temperature over this range, but those measured in hydrogen differ by more than an order of magnitude between 25 and 80 °C. The greatest enhancement is seen at 25 °C and at high values of ΔK, the maximum occurring between 40–45 MPa √m at each temperature. There is little hydrogen contribution to crack growth at values of ΔK below 20 MPa √m for R = 0.1. The enhancement of crack growth rates is reflected by the presence of ‘quasi-cleavage’ facets on the fatigue fracture surfaces of specimens tested in hydrogen. These are most apparent where the greatest increases in growth rate are recorded. The facets show linear markings, which run both parallel and perpendicular to the direction of crack growth. The former are analogous to the ‘river’ lines noted on brittle cleavage facets, and reflect the propagation direction. The latter are more unusual, and indicate that facet formation by hydrogen embrittlement during fatigue is a step-wise process.

Az ügyfélszerzési mód hatásának vizsgálata a vevőelégedettségre és a lojalitásra a szervezeti piacon (Analyzing the impact of the customer acquisition mode to the customer satisfaction and loyalty on the corporate market – assessing the effect of recommendation with applying structural equation modelling)

A kutatás célja a marketingeszközök hosszú távú hatásának pontosabb megértése szervezetközi viszonylatban a vevőértékelési modellek egyik nehezen számszerűsíthető tényezője, az ajánlás hatásának vizsgálata által. A hatások elemzésére a strukturális egyenlőségek módszerét (Structural Equation Modelling) alkalmazta a szerző. Rámutatott, hogy az ajánlással szerzett ügyfelek elégedettebbek, lojálisabbak és gyakrabban ajánlják a vállalatot a más módon szerzett ügyfeleknél. Az összefüggések feltárása és bizonyítása különösen az ajánlás kumulatív hatása miatt jelentős. Az eredmények gyakorlati alkalmazásával lehetőség nyílik az ügyfélkör differenciáltabb, értékalapú szegmentációjára, amely pontosabb célcsoport-meghatározást lesz lehetővé, és hosszú távon hozzájárul a vállalat optimális ügyfélportfóliójának kialakításához. ______ The research is aimed at more precise understanding of longterm effects of marketing tools in business to business relations by analysing the impacts of recommendation potential, one of the hardly measurable factors of customer value concept. Structural Equation Modelling is applied for conducting effect analysis. The results show that customers acquired with recommendation are more satisfied, more loyal, and make more recommendation that other customer. These results are more interesting if we take the cumulative effect of recommendation in account. They provide bases for a more differentiated segmentation of customers, which results in a more accurate identification of target groups. In the long-run, the application of the customer-value concept considerably contributes to creating an optimal customer portfolio for companies.

Temporal changes in immigration stress, adaptation, and the factors contributing to the immigration -adaptation process in newly immigrant parents

The adaptation process to a new land can be an arduous transition for families who migrate from their countries in an attempt to evade negative life conditions. Family-based immigration has been the cornerstone of immigration policy for the U.S. However, there has been a relative lack of attention given in immigration studies to the impact of immigration particularly on parents. Furthermore, little is known about their adjustment to their post-migration circumstances, particularly the initial phase of migration, where the psychological impact of immigration tends to be concentrated. It is even rarer that investigators have addressed longitudinally the dynamic process of parents' adaptation to a new ecology, which can shed a great deal of light on its mechanisms. In this dissertation, changes over time in levels of stress, adjustment (affect balance and life satisfaction), and the factors (social support, economic hardship, and discrimination) contributing to stress and adjustment were examined in newly immigrant parents from Argentina, Colombia, Cuba, Haiti, and the West Indies. Moderating effects of gender and country-of-origin were examined as well. This study also aimed to investigate to what extent the contributing factors impacted stress and adjustment, not only concurrently, but also over the first three years of post-migration. Analysis of variance results showed that both affect balance and social support increased whereas life satisfaction decreased over time. There was no significant change in stress, however. Both gender and group effects were also observed. Mothers experienced higher stress whereas fathers experienced higher discrimination. Among groups, Haitians appeared at the greatest risk in terms of stress, discrimination, and economic hardship. A structural equation modeling analysis showed that the relative importance of contributing factors changed over time in the process of immigrants' adaptation. Yet, social support emerged as a powerful protective factor in that its effects carried over time, and discrimination was a primary mediator through which other predictors were related to stress and adjustment. These findings shed light on the "hows and whys" of the immigration-adaptation process, by demonstrating the significance of specific conditions of life change to psychological outcomes as newly immigrant parents adapt to their post-migration ecology.

Multilevel structural equation models for longitudinal data where predictors are measured more frequently than outcomes : an application to the effects of stress on the cognitive function of nurses

Funded by Chief Scientist Office, Scotland. Grant Number: CZH/4/394 Economic and Social Research Council grant as part of the National Centre for Research Methods. Grant Number: RES-576-25-0032

The structural and piezoresponse properties of c-axis-oriented Aurivillius phase Bi5Ti3FeO15 thin films deposited by atomic vapor deposition

The deposition by atomic vapor deposition of highly c-axis-oriented Aurivillius phase Bi 5Ti 3FeO 15 (BTFO) thin films on (100) Si substrates is reported. Partially crystallized BTFO films with c-axis perpendicular to the substrate surface were first deposited at 610°C (8 excess Bi), and subsequently annealed at 820°C to get stoichiometric composition. After annealing, the films were highly c-axis-oriented, showing only (00l) peaks in x-ray diffraction (XRD), up to (0024). Transmission electron microscopy (TEM) confirms the BTFO film has a clear layered structure, and the bismuth oxide layer interleaves the four-block pseudoperovskite layer, indicating the n 4 Aurivillius phase structure. Piezoresponse force microscopy measurements indicate strong in-plane piezoelectric response, consistent with the c-axis layered structure, shown by XRD and TEM.

Projecting Changes in the Distribution and Productivity of Living Marine Resources: A Critical Review of the Suite of Modeling Approaches used in the Large European Project VECTORS

We review and compare four broad categories of spatially-explicit modelling approaches currently used to understand and project changes in the distribution and productivity of living marine resources including: 1) statistical species distribution models, 2) physiology-based, biophysical models of single life stages or the whole life cycle of species, 3) food web models, and 4) end-to-end models. Single pressures are rare and, in the future, models must be able to examine multiple factors affecting living marine resources such as interactions between: i) climate-driven changes in temperature regimes and acidification, ii) reductions in water quality due to eutrophication, iii) the introduction of alien invasive species, and/or iv) (over-)exploitation by fisheries. Statistical (correlative) approaches can be used to detect historical patterns which may not be relevant in the future. Advancing predictive capacity of changes in distribution and productivity of living marine resources requires explicit modelling of biological and physical mechanisms. New formulations are needed which (depending on the question) will need to strive for more realism in ecophysiology and behaviour of individuals, life history strategies of species, as well as trophodynamic interactions occurring at different spatial scales. Coupling existing models (e.g. physical, biological, economic) is one avenue that has proven successful. However, fundamental advancements are needed to address key issues such as the adaptive capacity of species/groups and ecosystems. The continued development of end-to-end models (e.g., physics to fish to human sectors) will be critical if we hope to assess how multiple pressures may interact to cause changes in living marine resources including the ecological and economic costs and trade-offs of different spatial management strategies. Given the strengths and weaknesses of the various types of models reviewed here, confidence in projections of changes in the distribution and productivity of living marine resources will be increased by assessing model structural uncertainty through biological ensemble modelling.

Projecting Changes in the Distribution and Productivity of Living Marine Resources: A Critical Review of the Suite of Modeling Approaches used in the Large European Project VECTORS

We review and compare four broad categories of spatially-explicit modelling approaches currently used to understand and project changes in the distribution and productivity of living marine resources including: 1) statistical species distribution models, 2) physiology-based, biophysical models of single life stages or the whole life cycle of species, 3) food web models, and 4) end-to-end models. Single pressures are rare and, in the future, models must be able to examine multiple factors affecting living marine resources such as interactions between: i) climate-driven changes in temperature regimes and acidification, ii) reductions in water quality due to eutrophication, iii) the introduction of alien invasive species, and/or iv) (over-)exploitation by fisheries. Statistical (correlative) approaches can be used to detect historical patterns which may not be relevant in the future. Advancing predictive capacity of changes in distribution and productivity of living marine resources requires explicit modelling of biological and physical mechanisms. New formulations are needed which (depending on the question) will need to strive for more realism in ecophysiology and behaviour of individuals, life history strategies of species, as well as trophodynamic interactions occurring at different spatial scales. Coupling existing models (e.g. physical, biological, economic) is one avenue that has proven successful. However, fundamental advancements are needed to address key issues such as the adaptive capacity of species/groups and ecosystems. The continued development of end-to-end models (e.g., physics to fish to human sectors) will be critical if we hope to assess how multiple pressures may interact to cause changes in living marine resources including the ecological and economic costs and trade-offs of different spatial management strategies. Given the strengths and weaknesses of the various types of models reviewed here, confidence in projections of changes in the distribution and productivity of living marine resources will be increased by assessing model structural uncertainty through biological ensemble modelling.

All-regime Lagrangian-Remap numerical schemes for the gas dynamics equations. Applications to the large friction and low Mach coefficients

In this talk, we propose an all regime Lagrange-Projection like numerical scheme for the gas dynamics equations. By all regime, we mean that the numerical scheme is able to compute accurate approximate solutions with an under-resolved discretization with respect to the Mach number M, i.e. such that the ratio between the Mach number M and the mesh size or the time step is small with respect to 1. The key idea is to decouple acoustic and transport phenomenon and then alter the numerical flux in the acoustic approximation to obtain a uniform truncation error in term of M. This modified scheme is conservative and endowed with good stability properties with respect to the positivity of the density and the internal energy. A discrete entropy inequality under a condition on the modification is obtained thanks to a reinterpretation of the modified scheme in the Harten Lax and van Leer formalism. A natural extension to multi-dimensional problems discretized over unstructured mesh is proposed. Then a simple and efficient semi implicit scheme is also proposed. The resulting scheme is stable under a CFL condition driven by the (slow) material waves and not by the (fast) acoustic waves and so verifies the all regime property. Numerical evidences are proposed and show the ability of the scheme to deal with tests where the flow regime may vary from low to high Mach values.

Numerical study of circulation in the Caspian Sea and its effects on the southern coastal currents

In this study, numerical simulation of the Caspian Sea circulation was performed using COHERENS three-dimensional numerical model and field data. The COHERENS three-dimensional model and FVCOM were performed under the effect of the wind driven force, and then the simulation results obtained were compared. Simulation modeling was performed at the Caspian Sea. Its horizontal grid size is approximately equal to 5 Km and 30 sigma levels were considered. The numerical simulation results indicate that the winds' driven-forces and temperature gradient are the most important driving force factors of the Caspian circulation pattern. One of the effects of wind-driven currents was the upwelling phenomenon that was formed in the eastern shores of the Caspian Sea in the summer. The simulation results also indicate that this phenomenon occurred at a depth less than 40 meters, and the vertical velocity in July and August was 10 meters and 7 meters respectively. During the upwelling phenomenon period the temperatures on the east coast compared to the west coast were about 5°C lower. In autumn and winter, the warm waters moved from the south east coast to the north and the cold waters moved from the west coast of the central Caspian toward the south. In the subsurface and deep layers, these movements were much more structured and caused strengthening of the anti-clockwise circulation in the area, especially in the central area of Caspian. The obtained results of the two models COHERENS and FVCOM performed under wind driven-force show a high coordination of the two models, and so the wind current circulation pattern for both models is almost identical.

Multiple solutions and numerical analysis to the dynamic and stationary models coupling a delayed energy balance model involving latent heat and discontinuous albedo with a deep ocean

We study a climatologically important interaction of two of the main components of the geophysical system by adding an energy balance model for the averaged atmospheric temperature as dynamic boundary condition to a diagnostic ocean model having an additional spatial dimension. In this work, we give deeper insight than previous papers in the literature, mainly with respect to the 1990 pioneering model by Watts and Morantine. We are taking into consideration the latent heat for the two phase ocean as well as a possible delayed term. Non-uniqueness for the initial boundary value problem, uniqueness under a non-degeneracy condition and the existence of multiple stationary solutions are proved here. These multiplicity results suggest that an S-shaped bifurcation diagram should be expected to occur in this class of models generalizing previous energy balance models. The numerical method applied to the model is based on a finite volume scheme with nonlinear weighted essentially non-oscillatory reconstruction and Runge–Kutta total variation diminishing for time integration.

APPLICATION OF AN IMPUTATION METHOD FOR GEOSPATIAL INVENTORY OF FOREST STRUCTURAL ATTRIBUTES ACROSS MULTIPLE SPATIAL SCALES IN THE LAKE STATES, U.S.A.

Credible spatial information characterizing the structure and site quality of forests is critical to sustainable forest management and planning, especially given the increasing demands and threats to forest products and services. Forest managers and planners are required to evaluate forest conditions over a broad range of scales, contingent on operational or reporting requirements. Traditionally, forest inventory estimates are generated via a design-based approach that involves generalizing sample plot measurements to characterize an unknown population across a larger area of interest. However, field plot measurements are costly and as a consequence spatial coverage is limited. Remote sensing technologies have shown remarkable success in augmenting limited sample plot data to generate stand- and landscape-level spatial predictions of forest inventory attributes. Further enhancement of forest inventory approaches that couple field measurements with cutting edge remotely sensed and geospatial datasets are essential to sustainable forest management. We evaluated a novel Random Forest based k Nearest Neighbors (RF-kNN) imputation approach to couple remote sensing and geospatial data with field inventory collected by different sampling methods to generate forest inventory information across large spatial extents. The forest inventory data collected by the FIA program of US Forest Service was integrated with optical remote sensing and other geospatial datasets to produce biomass distribution maps for a part of the Lake States and species-specific site index maps for the entire Lake State. Targeting small-area application of the state-of-art remote sensing, LiDAR (light detection and ranging) data was integrated with the field data collected by an inexpensive method, called variable plot sampling, in the Ford Forest of Michigan Tech to derive standing volume map in a cost-effective way. The outputs of the RF-kNN imputation were compared with independent validation datasets and extant map products based on different sampling and modeling strategies. The RF-kNN modeling approach was found to be very effective, especially for large-area estimation, and produced results statistically equivalent to the field observations or the estimates derived from secondary data sources. The models are useful to resource managers for operational and strategic purposes.