Strength properties of composite clay balls containing additives from industry wastes as new filter media in water treatment

Pebble matrix filtration (PMF) is a water treatment technology that can remove suspended solids in highly turbid surface water during heavy storms. PMF typically uses sand and natural pebbles as filter media. Hand-made clay pebbles (balls) can be used as alternatives to natural pebbles in PMF treatment plants, where natural pebbles are not readily available. Since the high turbidity is a seasonal problem that occurs during heavy rains, the use of newly developed composite clay balls instead of pure clay balls have the advantage of removing other pollutants such as natural organic matter (NOM) during other times. Only the strength properties of composite clay balls are described here as the pollutant removal is beyond the scope of this paper. These new composite clay balls must be able to withstand dead and live loads under dry and saturated conditions in a filter assembly. Absence of a standard ball preparation process and expected strength properties of composite clay balls were the main reasons behind the present study. Five different raw materials from industry wastes: Red Mud (RM), Water Treatment Alum Sludge (S), Shredded Paper (SP), Saw Dust (SD), and Sugar Mulch (SM) were added to common clay brick mix (BM) in different proportions. In an effort to minimize costs, in this study clay balls were fired to 1100 0C at a local brick factory together with their bricks. A comprehensive experimental program was performed to evaluate crushing strength of composite hand-made clay balls, using uniaxial compression test to establish the best material combination on the basis of strength properties for designing sustainable filter media for water treatment plants. Performance at both construction and operating stages were considered by analyzing both strength properties under fully dry conditions and strength degradation after saturation in a water bath. The BM-75% as the main component produced optimum combination in terms of workability and strength. With the material combination of BM-75% and additives-25%, the use of Red Mud and water treatment sludge as additives produced the highest and lowest strength of composite clay balls, with a failure load of 5.4 kN and 1.4 kN respectively. However, this lower value of 1.4 kN is much higher than the effective load on each clay ball of 0.04 kN in a typical filter assembly (safety factor of 35), therefore, can still be used as a suitable filter material for enhanced pollutant removal.

Art and science as creative catalysts

Science, Art and Science Art collaborations are generally presented and understood in terms of their products. We argue that the process of Science art can be a significant, even principal benefit of these collaborations, even though it may be largely invisible to anyone other than the collaborators. Hosting the Centenary of Canberra Science Art Commission at the Commonwealth Scientific and Industrial Research Organisation (CSIRO) has shown us that while Science and Art pursue orthogonal dimensions of creativity and innovation, collaborators can combine these directions to access new areas of imagination and ideas.

Performance-Based Quality Assurance/Quality Control (QA/QC) Acceptance Procedures for In-Place Soil Testing Phase 3

One of the objectives of this study was to evaluate soil testing equipment based on its capability of measuring in-place stiffness or modulus values. As design criteria transition from empirical to mechanistic-empirical, soil test methods and equipment that measure properties such as stiffness and modulus and how they relate to Florida materials are needed. Requirements for the selected equipment are that they be portable, cost effective, reliable, a ccurate, and repeatable. A second objective is that the selected equipment measures soil properties without the use of nuclear materials.The current device used to measure soil compaction is the nuclear density gauge (NDG). Equipment evaluated in this research included lightweight deflectometers (LWD) from different manufacturers, a dynamic cone penetrometer (DCP), a GeoGauge, a Clegg impact soil tester (CIST), a Briaud compaction device (BCD), and a seismic pavement analyzer (SPA). Evaluations were conducted over ranges of measured densities and moistures.Testing (Phases I and II) was conducted in a test box and test pits. Phase III testing was conducted on materials found on five construction projects located in the Jacksonville, Florida, area. Phase I analyses determined that the GeoGauge had the lowest overall coefficient of variance (COV). In ascending order of COV were the accelerometer-type LWD, the geophone-type LWD, the DCP, the BCD, and the SPA which had the highest overall COV. As a result, the BCD and the SPA were excluded from Phase II testing.In Phase II, measurements obtained from the selected equipment were compared to the modulus values obtained by the static plate load test (PLT), the resilient modulus (MR) from laboratory testing, and the NDG measurements. To minimize soil and moisture content variability, the single spot testing sequence was developed. At each location, test results obtained from the portable equipment under evaluation were compared to the values from adjacent NDG, PLT, and laboratory MR measurements. Correlations were developed through statistical analysis. Target values were developed for various soils for verification on similar soils that were field tested in Phase III. The single spot testing sequence also was employed in Phase III, field testing performed on A-3 and A-2-4 embankments, limerock-stabilized subgrade, limerock base, and graded aggregate base found on Florida Department of Transportation construction projects. The Phase II and Phase III results provided potential trend information for future research—specifically, data collection for in-depth statistical analysis for correlations with the laboratory MR for specific soil types under specific moisture conditions. With the collection of enough data, stronger relationships could be expected between measurements from the portable equipment and the MR values. Based on the statistical analyses and the experience gained from extensive use of the equipment, the combination of the DCP and the LWD was selected for in-place soil testing for compaction control acceptance. Test methods and developmental specifications were written for the DCP and the LWD. The developmental specifications include target values for the compaction control of embankment, subgrade, and base materials.

Managing knowledge to promote sustainability in Australian transport infrastructure projects

To deliver tangible sustainability outcomes, the infrastructure sector of the construction industry needs to build capacities for the creation, application and management of ever increasing knowledge. This paper intends to establish the importance and key issues of promoting sustainability through knowledge management (KM). It presents a new conceptual framework for managing sustainability knowledge to raise the awareness and direct future research in the field of transport infrastructure, one of the fast growing sectors in Australia. A holistic KM approach is adopted in this research to consider the potential to “deliver the right information to the right person at the right time” in the context of sustainable development of infrastructure. A questionnaire survey among practitioners across the nation confirmed the necessity and identified priority issues of managing knowledge for sustainability. During infrastructure development, KM can help build much needed industry consensus, develop capacity, communicate decisions, and promote specific measures for the pursuit of sustainability. Six essential elements of the KM approach and their priority issues informed the establishment of a conceptual KM framework. The transport infrastructure sector has come to realise that development must not come at the expense of environmental and social objectives. In practice however, it is facing extensive challenges to deliver what has been promised in the sustainability agenda. This research demonstrates the importance of managing sustainability knowledge, integration of various stakeholders, facilitation of plans and actions and delivery of tangible benefits in real projects, as a positive step towards meeting these challenges.

Patent-busting: The public patent foundation, gene patents and the Seed Wars

This chapter considers the Public Patent Foundation as a novel institution in the patent framework. It contends that such a model can play a productive role in challenging the validity of high-profile patents; working as an amicus curiae in significant court cases; and also promoting patent law reform. However, there are limits to the ‘patent-busting’ of the Foundation. The not-for-profit legal services organization has only had the time and resources to challenge a number of noteworthy patents. Other jurisdictions – such as Australia – lack such public-spirited "patent-busting" entities. This chapter considers a number of key disputes involving the Public Patent Foundation. Part I examines the role of the Public Patent Foundation in the landmark dispute over Myriad Genetics’ patents in respect of breast cancer and ovarian cancer. Part II considers the role of the Public Patent Foundation in litigation between organic farmers and Monsanto. Part III examines the role of the Public Patent Foundation in larger debates about patent law reform in the United States – particularly looking at the Leahy-Smith America Invents Act 2011 (US). The conclusion contends that the patent-busting model of the Public Patent Foundation should be emulated in respect of other technological fields, and other jurisdictions – such as Australia. The initiative could also be productively applied to other forms of intellectual property – such as trade mark law, designs law, plant breeders’ rights, plant breeders’ rights, and access to genetic resources.

Identifying and forecasting the reverse salient in video game consoles: A performance gap ratio comparative analysis

This study uses the reverse salient methodology to contrast subsystems in video game consoles in order to discover, characterize, and forecast the most significant technology gap. We build on the current methodologies (Performance Gap and Time Gap) for measuring the magnitude of Reverse Salience, by showing the effectiveness of Performance Gap Ratio (PGR). The three subject subsystems in this analysis are the CPU Score, GPU core frequency, and video memory bandwidth. CPU Score is a metric developed for this project, which is the product of the core frequency, number of parallel cores, and instruction size. We measure the Performance Gap of each subsystem against concurrently available PC hardware on the market. Using PGR, we normalize the evolution of these technologies for comparative analysis. The results indicate that while CPU performance has historically been the Reverse Salient, video memory bandwidth has taken over as the quickest growing technology gap in the current generation. Finally, we create a technology forecasting model that shows how much the video RAM bandwidth gap will grow through 2019 should the current trend continue. This analysis can assist console developers in assigning resources to the next generation of platforms, which will ultimately result in longer hardware life cycles.

Stabilization of stormwater biofilters: Impacts of wetting and drying phases and the addition of organic matter to filter media

Ripening period refers to a phase of stabilization in sand filters in water treatment systems that follows a new installation or cleaning of the filter. Intermittent wetting and drying, a unique property of stormwater biofilters, would similarly be subjected to a phase of stabilization. Suspended solids, is an important parameter that is often used to monitor the stabilization of sand filters in water treatment systems. Stormwater biofilters however, contain organic material that is added to the filter layer to enhance nitrate removal, the dynamics of which is seldom analysed in stabilization of stormwater biofilters. Therefore, in this study of stormwater biofiltration in addition to suspended solids (Turbidity), organic matter (TOC, DOC, TN and TKN) was also monitored as a parameter for stabilization of the stormwater biofilter. One Perspex bioretention column (94 mm internal diameter) was fabricated with filter layer that contained 8% organic material and fed with tapwater with different antecedent dry days (0 – 40 day) at 100 mL/min. Samples were collected from the outflow at different time intervals between 2 – 150 minutes and were tested for Total Organic Carbon, Dissolved Organic Carbon, Total Nitrogen, Total Kjeldhal Nitrogen and Turbidity. The column was observed to experience two phases of stabilization, one at the beginning of each event that lasted for 30 minutes while the other phase was observed across subsequent events that related to the age of filter.

Practical guidelines for planning and implementing fauna translocations

A successful translocation involves many complex factors, including a genetically appropriate source population that can sustain harvest, social and governmental support, assessment of disease transmission risk and a release site with appropriately secure habitat that can support population establishment and persistance. This information is typically discussed during staturory approval processes and can take considerable time. However, following approval, for translocations of most fauna, the initial critical step involves the inherently stressful process of capture, holding, transportation and release. This process is unpredictable and novel, and is especially challenging for wild animals when they are confined in close proximity to conspecifics and humans. In contrast, captive-reared animals have to cope with the unfamiliar challenges of finding food and shelter, along with coping with competition and predation. Little has been written in the scientific literature about the translocation process. This is unsurprising because this process has usually been the realm of skilled practioners, often with animal husbandry backgrounds, rather than research scientists. Highly skilled intuition, observation and the translocation practioner's equivalent of a 'green thumb' often guides the way. However, theory and experimentation, particularly on the effects of stress, is available and this work is invaluable for a successful translocation. Here, we provide a brief description of the translocation process, and discussion of what stress is and how it can be managed. We then provide practical guidelines for the successful translocation of invertebrates, lizards, turtles, passerine birds, marsupials and bats, using examples from Australia and New Zealand.

pH testing for detecting the position of nasogastric tubes in adults and children (Intervention Protocol)

This is the protocol for a review and there is no abstract. The objectives are as follows: Our objective is to determine if there is sufficient evidence to recommend the use of pH testing (the intervention under scrutiny) for verification of correct placement of nasogastric tubes in adults and children. To this end, we will attempt to answer the following questions: 1. In adults and children, is pH testing an effective and safe method for determining whether nasogastric tubes are correctly positioned in the stomach before feeding (or delivery of any fluid) begins? 2. What evidence is there about the risk of adverse events in the case of incorrect placement? For this review, pH testing is defined as: litmus paper, pH indicator test strips, pH meters. These will be tested against other methods used for detecting placement of nasogastric tubes, including visual examination of aspirate, auscultation with insufflation of air, detection of air bubbles in a bowl of water, X-ray, ultrasonography, endoscopy, enzyme analysis of aspirate, capnography, and other methods that do not rely on measurement of pH.

Development of a new design expression for the in-plane shear capacity of the partially grouted concrete masonry walls

Partially grouted masonry walls subjected to in-plane shear exhibit a complex behaviour because of the influence of the aspect ratio, the pre-compression, the grouting pattern, the ratios of the horizontal and the vertical reinforcements, the boundary conditions and the characteristics of the constituent materials. The existing in-plane shear expressions for the partially grouted masonry are formulated as sum of strength of three parameters, namely, the masonry, the reinforcement and the axial force. The parameter ‘masonry’ includes the wall aspect ratio and the masonry compressive strength; the aspect ratio of the unreinforced panel inscribed into the grouted cores and bond beams are not considered, although failure is often dominated by these unreinforced masonry panels. This paper describes the dominance of these panels, particularly those that are squat, to the shear capacity of whole of shear walls. Further, the current design formulae are shown highly un-conservative by many researchers; this paper provides a potential reason for this un-conservativeness. It is shown that by including an additional term of the unreinforced panel aspect ratio a rational design formula could be established. This new expression is validated with independent test results reported in the literature – both Australian and overseas; the predictions are shown to be conservative.

Modeling approaches for pesticide exposure assessment in rice paddies

Pesticide use in paddy rice production may contribute to adverse ecological effects in surface waters. Risk assessments conducted for regulatory purposes depend on the use of simulation models to determine predicted environment concentrations (PEC) of pesticides. Often tiered approaches are used, in which assessments at lower tiers are based on relatively simple models with conservative scenarios, while those at higher tiers have more realistic representations of physical and biochemical processes. This chapter reviews models commonly used for predicting the environmental fate of pesticides in rice paddies. Theoretical considerations, unique features, and applications are discussed. This review is expected to provide information to guide model selection for pesticide registration, regulation, and mitigation in rice production areas.

Schizophrenia Genetic Variants are not Associated with Intelligence

Background Schizophrenia is associated with lower pre-morbid intelligence (IQ) in addition to (pre-morbid) cognitive decline. Both schizophrenia and IQ are highly heritable traits. Therefore, we hypothesized that genetic variants associated with schizophrenia, including copy number variants (CNVs) and a polygenic schizophrenia (risk) score (PSS), may influence intelligence. Method IQ was estimated with the Wechsler Adult Intelligence Scale (WAIS). CNVs were determined from single nucleotide polymorphism (SNP) data using the QuantiSNP and PennCNV algorithms. For the PSS, odds ratios for genome-wide SNP data were calculated in a sample collected by the Psychiatric Genome-Wide Association Study (GWAS) Consortium (8690 schizophrenia patients and 11 831 controls). These were used to calculate individual PSSs in our independent sample of 350 schizophrenia patients and 322 healthy controls. Results Although significantly more genes were disrupted by deletions in schizophrenia patients compared to controls (p = 0.009), there was no effect of CNV measures on IQ. The PSS was associated with disease status (R 2 = 0.055, p = 2.1 × 10 -7) and with IQ in the entire sample (R 2 = 0.018, p = 0.0008) but the effect on IQ disappeared after correction for disease status. Conclusions Our data suggest that rare and common schizophrenia-associated variants do not explain the variation in IQ in healthy subjects or in schizophrenia patients. Thus, reductions in IQ in schizophrenia patients may be secondary to other processes related to schizophrenia risk. © Cambridge University Press 2013.

Genome-wide association study identifies five new schizophrenia loci

We examined the role of common genetic variation in schizophrenia in a genome-wide association study of substantial size: a stage 1 discovery sample of 21,856 individuals of European ancestry and a stage 2 replication sample of 29,839 independent subjects. The combined stage 1 and 2 analysis yielded genome-wide significant associations with schizophrenia for seven loci, five of which are new (1p21.3, 2q32.3, 8p23.2, 8q21.3 and 10q24.32-q24.33) and two of which have been previously implicated (6p21.32-p22.1 and 18q21.2). The strongest new finding (P = 1.6 × 10 -11) was with rs1625579 within an intron of a putative primary transcript for MIR137 (microRNA 137), a known regulator of neuronal development. Four other schizophrenia loci achieving genome-wide significance contain predicted targets of MIR137, suggesting MIR137-mediated dysregulation as a previously unknown etiologic mechanism in schizophrenia. In a joint analysis with a bipolar disorder sample (16,374 affected individuals and 14,044 controls), three loci reached genome-wide significance: CACNA1C (rs4765905, P = 7.0 × 10 -9), ANK3 (rs10994359, P = 2.5 × 10 -8) and the ITIH3-ITIH4 region (rs2239547, P = 7.8 × 10 -9).

Archaeology of wings : Birds and people in the Baltic Sea region during the Stone Age

The prominent roles of birds, often mentioned in historical sources, are not well reflected in archaeological research. Absence or scarcity of bird bones in archaeological assemblages has been often seen as indication of a minor role of birds in the prehistoric economy or ideology, or explained by taphonomic loss. Few studies exist where birds form the basis for extensive archaeological interpretation. In this doctoral dissertation bird bone material from various Stone Age sites in the Baltic Sea region is investigated. The study period is approximately 7000-3400 BP, comprising mainly Neolithic cultures. The settlement material comes from Finland, Åland, Gotland, Saaremaa and Hiiumaa. Osteological materials are used for studying the economic and cultural importance of birds, fowling methods and principal fowling seasons. The bones were identified and earlier identifications partially checked with help of a reference material of modern skeletons. Fracture analysis was used in order to study the deposition history of bones at Ajvide settlement site. Birds in burials at two large cemeteries, Ajvide on Gotland and Zvejnieki in northern Latvia were investigated in order to study the roles of birds in burial practices. My study reveals that the economic importance of birds is at least seasonally often more prominent than usually thought, and varies greatly in different areas. Fowling has been most important in coastal areas, and especially during the breeding season. Waterbirds and grouse species were generally the most important groups in Finnish Stone Age economy. The identified species composition shows much resemblance to contemporary hunting with species such as the mallard and capercaillie commonly found. Burial materials and additional archaeological evidence from Gotland, Latvia and some other parts of northern Europe indicate that birds –e.g., jay, whooper swan, ducks – have been socially and ideologically important for the studied groups (indicating a place in the belief system, e.g. clan totemism). The burial finds indicate that some common ideas about waterbirds (perhaps as messengers or spirit helpers) might have existed in the northern European Stone Age.

Analysis of physical activity in emmetropic and myopic university students during semester and holiday periods: A pilot study

Background Previous studies (mostly questionnaire-based in children) suggest that outdoor activity is protective against myopia. There are few studies on young adults investigating both the impact of simply being outdoors versus performing physical activity. The aim was to study the relationship between the refractive error of young adults and their physical activity patterns. Methods Twenty-seven university students, aged 18 to 25 years, wore a pedometer (Omron HJ720ITE) for seven days both during the semester and holiday periods. They simultaneously recorded the type of activity performed, its duration, the number of steps taken (from the pedometer) and their location (indoors/outdoors) in a logbook. Mean spherical refractive error was used to divide participants into three groups (emmetropes: +1.00 to -0.50 D, low myopes: -0.62 to -3.00 D, higher myopes: -3.12 D or greater myopia). Results There were no significant differences between the refractive groups during the semester or holiday periods; the average daily times spent outdoors, the duration of physical activity, the ratio of physical activity performed outdoors to indoors and amount of near work performed were similar. The peak exercise intensity was similar across all groups: approximately 100 steps perminute, a brisk walk. Up to one-third of all physical activity was performed outdoors. There were some significant differences in activities performed during semester and holiday times. For example, lowmyopes spent significantly less time outside (49 ± 47 versus 74 ± 41 minutes, p = 0.005) and performed less physical activity (6,388 ± 1,747 versus 6,779 ± 2,746 steps per day; p = 0.03) during the holidays compared to during semester. Conclusions The fact that all groups had similar low exercise intensity butmany were notmyopic suggests that physical activity levels are not critical. There were differences in the activity patterns of lowmyopes during semester and holiday periods. This study highlights the need for a larger longitudinal-based study with particular emphasis on how discretionary time is spent.