The oxidative potential of differently charged silver and gold nanoparticles on three human lung epithelial cell types

Background: Nanoparticle (NPs) functionalization has been shown to affect their cellular toxicity. To study this, differently functionalized silver (Ag) and gold (Au) NPs were synthesised, characterised and tested using lung epithelial cell systems. Mehtods: Monodispersed Ag and Au NPs with a size range of 7 to 10 nm were coated with either sodium citrate or chitosan resulting in surface charges from ¿50 mV to +70 mV. NP-induced cytotoxicity and oxidative stress were determined using A549 cells, BEAS-2B cells and primary lung epithelial cells (NHBE cells). TEER measurements and immunofluorescence staining of tight junctions were performed to test the growth characteristics of the cells. Cytotoxicity was measured by means of the CellTiter-Blue ® and the lactate dehydrogenase assay and cellular and cell-free reactive oxygen species (ROS) production was measured using the DCFH-DA assay. Results: Different growth characteristics were shown in the three cell types used. A549 cells grew into a confluent mono-layer, BEAS-2B cells grew into a multilayer and NHBE cells did not form a confluent layer. A549 cells were least susceptible towards NPs, irrespective of the NP functionalization. Cytotoxicity in BEAS-2B cells increased when exposed to high positive charged (+65-75 mV) Au NPs. The greatest cytotoxicity was observed in NHBE cells, where both Ag and Au NPs with a charge above +40 mV induced cytotoxicity. ROS production was most prominent in A549 cells where Au NPs (+65-75 mV) induced the highest amount of ROS. In addition, cell-free ROS measurements showed a significant increase in ROS production with an increase in chitosan coating. Conclusions: Chitosan functionalization of NPs, with resultant high surface charges plays an important role in NP-toxicity. Au NPs, which have been shown to be inert and often non-cytotoxic, can become toxic upon coating with certain charged molecules. Notably, these effects are dependent on the core material of the particle, the cell type used for testing and the growth characteristics of these cell culture model systems.

General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Spectral analysis of the angular distribution function of back reflectors for thin film silicon solar cells

Nowadays, one of the most important challenges to enhance the efficiency of thin film silicon solar cells is to increase the short circuit intensity by means of optical confinement methods, such as textured back-reflector structures. In this work, two possible textured structures to be used as back reflectors for n-i-p solar cells have been optically analyzed and compared to a smooth one by using a system which is able to measure the angular distribution function (ADF) of the scattered light in a wide spectral range (350-1000 nm). The accurate analysis of the ADF data corresponding to the reflector structures and to the μc-Si:H films deposited onto them allows the optical losses due to the reflector absorption and its effectiveness in increasing light absorption in the μc-Si:H layer, mainly at long wavelengths, to be quantified.

Hermetic sealing of food packaging trays

Suojakaasupakkaaminen on lisääntynyt voimakkaasti viime vuosina elintarvikkeiden pakkaamisessa sillä pakkaamalla elintarvike suojakaasuun voidaan sen hyllyikää pidentää ilman säilöntäaineita. Tällainen pakkaaminen vaatii kuitenkin täysin kaasutiiviin pakkauksen, jonka kaasunläpäisevyys on myös alhainen. Yleisimmin käytetyt pakkausmateriaalit suojakaasupakkaamisessa ovat monikerroksiset muovimateriaalit, joissa yhdistyy monen eri muovin parhaimmat ominaisuudet. Yleisimmin käytettyjä muovilaatuja näissä monikerrosrakenteissa ovat PE, PET, PA ja EVOH polymeerit. Myös muita perinteisiä polymeerejä käytetään jonkin verran näissä rakenteissa. Uudemmat muovilaadut, kuten biohajoavat muovit, eivät ole vielä yleistyneet kaupallisessa käytössä pääasiallisesti niiden korkean hinnan vuoksi. Muovisten pakkausten korvaamista esimerkiksi muovipäällystetyillä kartonkipakkauksilla on viime vuosien aikana tutkittu enenevissä määrin. Muovipakkausten korvaamista helpommin kierrätettävillä ja mahdollisesti biohajoavilla materiaaleilla edistävät EU:n direktiivit, jotka käsittelevät pakkausjätteen käsittelyä. Kartonkivuokien saumaamista kaasutiiviisti tutkittiin myös tässä työssä. Tavoitteena oli löytää pakkaus, joka soveltuisi kanasuikaleiden pakkaamiseen suojakaasuun. Kana on herkkä mikrobiologiselle hajoamiselle, minkä johdosta se tulee pakata suojakaasuun jossa happipitoisuuden tulee olla alle 1 % pakkauspäivästä viimeiseen käyttöpäivään saakka. Suorittamalla erilaisia tiiveystutkimuksia voitiin osoittaa, että kartonkivuoka on mahdollista saumata kaasutiiviisti luotettavalla tavalla. Tämä vaatii kuitenkin kartonkivuokien valmistuksen optimoimista päällystemuovikerroksen ja kartongin paksuuden mukaan sekä kannen saumaamista optimoiduilla saumausparametreilla. Tiivein vuoka saavutettiin muovifilmikannella, jonka saumaus perustui samaan muoviin kuin vuoan saumaus. Polyeteenillä saavutettiin tiivein ja kestävin saumaustulos.

Fraktiointikerrostuksen vaikutus paperin laatuun

Työn tavoitteena oli kehittää prosessia fraktioinnista monikerrosperälaatikolle painopaperilajeilla. Tarkoituksena oli selvittää koeajojen avulla sihti- ja pyörrepuhdistusfraktioinnin soveltuvuutta paperin kerrostuksen kannalta. Työssä vertailtiin keskenään fraktiointimenetelmiä ja niiden yhdistelmiä. Tehtävänä oli prosessikonseptin kehittäminen eri prosessikytkennöistä ja –ratkaisuista simuloinnin avulla. Kirjallisuusosassa tutustuttiin analysoiden kirjallisuusviitteiden perusteella massan fraktiointiin ja paperin kerrostamiseen sekä fraktiointikerrostetun rainan karakterisointiin. Tavoitteiden saavuttamiseksi esikokeena suoritettiin pilotkoeajo hienopaperimassalla, jossa tutkittiin pääasiassa fraktiointitulosta. Toinen koeajo suoritettiin LWC-paperilla, jossa koekonekonsepti oli optimaalisempi kerrostuksen kannalta ja fraktiointitulos voitiin linkittää paperin laatusuureisiin. LWC-koeajossa fraktioidulla massalla tehtiin laboratoriomittakaavassa monikerrosarkkimuottikokeita, joiden tuloksilla pyrittiin vahvistamaan koeajosta saatuja tuloksia ja fraktioinnnin potentialia. Prosessikonseptin kehittämiseksi rakennettiin seitsemän simulointimallia eri kytkennöistä. Malleja verrattiin keskenään täyteaine- ja kuitujakeiden fraktiointikyvyn perusteella. Koeajojen avulla selvitettiin fraktioinnin kannalta optimaaliset prosessimuuttujat. Fraktiointikerrostuksella parannettiin paperin z-suuntaista lujuutta ja etenkin pyörrepuhdistinfraktioinnilla pintojen sileyttä. Fraktiointikerrostuksella voitiin parantaa paperin täyteainejakaumaa. Kokeiden perusteella huomattiin, että kukin paperilaji tarvitsee erilaisen fraktiointijärjestelyn riippuen käytetystä massasta ja täyteaineesta.

PEN as substrate for new solar cell technologies

The possible use of polyethylene naphthalate as substrate for low-temperature deposited solar cells has been studied in this paper. The transparency of this polymer makes it a candidate to be used in both substrate and superstrate configurations. ZnO:Al has been deposited at room temperature on top of PEN. The resulting structure PEN/ZnO:Al presented good optical and electrical properties. PEN has been successfully textured (nanometer and micrometer random roughness) using hot-embossing lithography. Reflector structures have been built depositing Ag and ZnO:Al on top of the stamped polymer. The deposition of these layers did not affect the final roughness of the whole. The reflector structure has been morphologically and optically analysed to verify its suitability to be used in solar cells.

ICA Cleaning procedure for EEG signals analysis: application to Alzheimer's disease detection

To develop systems in order to detect Alzheimer’s disease we want to use EEG signals. Available database is raw, so the first step must be to clean signals properly. We propose a new way of ICA cleaning on a database recorded from patients with Alzheimer's disease (mildAD, early stage). Two researchers visually inspected all the signals (EEG channels), and each recording's least corrupted (artefact-clean) continuous 20 sec interval were chosen for the analysis. Each trial was then decomposed using ICA. Sources were ordered using a kurtosis measure, and the researchers cleared up to seven sources per trial corresponding to artefacts (eye movements, EMG corruption, EKG, etc), using three criteria: (i) Isolated source on the scalp (only a few electrodes contribute to the source), (ii) Abnormal wave shape (drifts, eye blinks, sharp waves, etc.), (iii) Source of abnormally high amplitude ( �100 �V). We then evaluated the outcome of this cleaning by means of the classification of patients using multilayer perceptron neural networks. Results are very satisfactory and performance is increased from 50.9% to 73.1% correctly classified data using ICA cleaning procedure.

ICA as a preprocessing technique for classification

In this paper we propose the use of the independent component analysis (ICA) [1] technique for improving the classification rate of decision trees and multilayer perceptrons [2], [3]. The use of an ICA for the preprocessing stage, makes the structure of both classifiers simpler, and therefore improves the generalization properties. The hypothesis behind the proposed preprocessing is that an ICA analysis will transform the feature space into a space where the components are independent, and aligned to the axes and therefore will be more adapted to the way that a decision tree is constructed. Also the inference of the weights of a multilayer perceptron will be much easier because the gradient search in the weight space will follow independent trajectories. The result is that classifiers are less complex and on some databases the error rate is lower. This idea is also applicable to regression

On the Analysis and Control of a Linear Synchronous Servomotor with a Flexible Load

Industry's growing need for higher productivity is placing new demands on mechanisms connected with electrical motors, because these can easily lead to vibration problems due to fast dynamics. Furthermore, the nonlinear effects caused by a motor frequently reduce servo stability, which diminishes the controller's ability to predict and maintain speed. Hence, the flexibility of a mechanism and its control has become an important area of research. The basic approach in control system engineering is to assume that the mechanism connected to a motor is rigid, so that vibrations in the tool mechanism, reel, gripper or any apparatus connected to the motor are not taken into account. This might reduce the ability of the machine system to carry out its assignment and shorten the lifetime of the equipment. Nonetheless, it is usually more important to know how the mechanism, or in other words the load on the motor, behaves. A nonlinear load control method for a permanent magnet linear synchronous motor is developed and implemented in the thesis. The purpose of the controller is to track a flexible load to the desired velocity reference as fast as possible and without awkward oscillations. The control method is based on an adaptive backstepping algorithm with its stability ensured by the Lyapunov stability theorem. As a reference controller for the backstepping method, a hybrid neural controller is introduced in which the linear motor itself is controlled by a conventional PI velocity controller and the vibration of the associated flexible mechanism is suppressed from an outer control loop using a compensation signal from a multilayer perceptron network. To avoid the local minimum problem entailed in neural networks, the initial weights are searched for offline by means of a differential evolution algorithm. The states of a mechanical system for controllers are estimated using the Kalman filter. The theoretical results obtained from the control design are validated with the lumped mass model for a mechanism. Generalization of the mechanism allows the methods derived here to be widely implemented in machine automation. The control algorithms are first designed in a specially introduced nonlinear simulation model and then implemented in the physical linear motor using a DSP (Digital Signal Processor) application. The measurements prove that both controllers are capable of suppressing vibration, but that the backstepping method is superior to others due to its accuracy of response and stability properties.

Amorphous silicon thin film solar cells deposited entirely by Hot-Wire Chemical Vapour Deposition at low temperature (<150 ºC)

Amorphous silicon n-i-p solar cells have been fabricated entirely by Hot-Wire Chemical Vapour Deposition (HW-CVD) at low process temperature < 150 °C. A textured-Ag/ZnO back reflector deposited on Corning 1737F by rf magnetron sputtering was used as the substrate. Doped layers with very good conductivity and a very less defective intrinsic a-Si:H layer were used for the cell fabrication. A double n-layer (μc-Si:H/a-Si:H) and μc-Si:H p-layer were used for the cell. In this paper, we report the characterization of these layers and the integration of these layers in a solar cell fabricated at low temperature. An initial efficiency of 4.62% has been achieved for the n-i-p cell deposited at temperatures below 150 °C over glass/Ag/ZnO textured back reflector.

Structure of a-Si:H/a-Si1-xCx:H multilayers deposited in a reactor with automated substrate holder

This paper deals with the structural properties of a-Si:H/a-Si1-xCx: H multilayers deposited by glow-discharge decomposition of SiH4 and SiH4 and CH4 mixtures. The main feature of the rf plasma reactor is an automated substrate holder. The plasma stabilization time and its influence on the multilayer obtained is discussed. A series of a-Si:H/a-Si1-xCx: H multilayers has been deposited and characterized by secondary ion mass spectrometry (SIMS), X-ray diffraction (XRD) and transmission electron microscopy (TEM). No asymmetry between the two types of interface has been observed. The results show that the multilayers present a very good periodicity and low roughness. The difficulty of determining the abruptness of the multilayer at the nanometer scale is discussed.

New features of the layer-by-layer deposition of microcrystalline silicon films revealed by spectroscopic ellipsometry and high resolution transmission electron microscopy

Spectroscopic ellipsometry and high resolution transmission electron microscopy have been used to characterize microcrystalline silicon films. We obtain an excellent agreement between the multilayer model used in the analysis of the optical data and the microscopy measurements. Moreover, thanks to the high resolution achieved in the microscopy measurements and to the improved optical models, two new features of the layer-by-layer deposition of microcrystalline silicon have been detected: i) the microcrystalline films present large crystals extending from the a-Si:H substrate to the film surface, despite the sequential process in the layer-by-layer deposition; and ii) a porous layer exists between the amorphous silicon substrate and the microcrystalline silicon film.

A study of electromagnetic shielding properties of Ni79Fe16Mo5/copper films

The plane wave electromagnetic interference (EMI) shielding properties of DC sputtered Ni79Fe16Mo5 and copper layers were studied according to ASTM D 4935-89 on frequency range of 50 MHz – 2.5 GHz and RF magnetic shielding effectiveness by shielded magnetic loop probes. Results show that Ni79Fe16Mo5 provides better RF magnetic shielding above the layer thickness of approximately 120 nm. Copper provides better plane wave shielding effectiveness. The effect of shield internal interfaces was studied by depositing thin multilayer structures with and without a dielectric spacer layer.

Generalization transitions in Hidden-Layer neural networks for third-order feature discrimination

Stochastic learning processes for a specific feature detector are studied. This technique is applied to nonsmooth multilayer neural networks requested to perform a discrimination task of order 3 based on the ssT-block¿ssC-block problem. Our system proves to be capable of achieving perfect generalization, after presenting finite numbers of examples, by undergoing a phase transition. The corresponding annealed theory, which involves the Ising model under external field, shows good agreement with Monte Carlo simulations.

Filmes poliméricos ultrafinos produzidos pela técnica de automontagem: preparação, propriedades e aplicações

The self-assembly technique is a powerful tool to fabricate ultrathin films from organic compounds aiming at technological applications in molecular electronics. This relatively new approach allows molecularly flat films to be obtained on a simple and cheap fashion from various types of material, including polyelectrolytes, conducting polymers, dyes and proteins. The resulting multilayer films may be fabricated according to specific requirements since their structural and physical properties may be controlled at the molecular level. In this review we shall comment upon the evolution of preparation methods for ultrathin films, the process of adsorption and their main properties, as well as some examples of technological applications of layer-by-layer or self-assembled films.