Edge-to-edge matching and its applications - Part II. Application to Mg-Al, Mg-Y and Mg-Mn alloys

A model for the crystallography and morphology of diffusion-controlled phase transformations - edge-to-edge matching - has been used to predict the orientation relationships (OR) and habit planes of precipitates Mg17Al12 in Mg-Al alloy, Mg24Y5 in Mg-Y alloy and alpha-Mn in Mg-Mn alloy. Based on the crystal structures and lattice parameters only, the model predicts that the possible ORs between Mg17Al12 and Mg matrix are the near Burgers OR, the Potter OR, the Gjonnes-Ostmoe OR and the Crawley OR. In the Mg-Y alloy, the OR between Mg24Y5 precipitates and the Mg matrix is predicted to be the Burgers OR only. The model also predicts that there are no reproducible ORs between alpha-Mn and Mg in the Mg-Mn alloy. Combining the edge-to-edge matching model and W. Zhang's Deltag approach, the habit plane and side facets of the precipitate for each OR can be determined. All the predicted ORs and the corresponding habit planes in Mg-Al and Mg-Y alloys agree very well with the experimental results. (C) 2004 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Cdk1/Erk2- and Plk1-dependent phosphorylation of a centrosome protein, Cep55, is required for its recruitment to midbody and cytokinesis

Centrosomes in mammalian cells have recently been implicated in cytokinesis; however, their role in this process is poorly defined. Here, we describe a human coiled-coil protein, Cep55 (centrosome protein 55 kDa), that localizes to the mother centriole during interphase. Despite its association with gamma-TuRC anchoring proteins CG-NAP and Kendrin, Cep55 is not required for microtubule nucleation. Upon mitotic entry, centrosome dissociation of Cep55 is triggered by Erk2/Cdk1-dependent phosphorylation at S425 and S428. Furthermore, Cep55 locates to the midbody and plays a role in cytokinesis, as its depletion by siRNA results in failure of this process. S425/428 phosphorylation is required for interaction with Plk1, enabling phosphorylation of Cep55 at S436. Cells expressing phosphorylation-deficient mutant forms of Cep55 undergo cytokinesis failure. These results highlight the centrosome as a site to organize phosphorylation of Cep55, enabling it to relocate to the midbody to function in mitotic exit and cytokinesis.

Edge-to-edge matching - The fundamentals

The basis of the present authors' edge-to-edge matching model for understanding the crystallography of partially coherent precipitates is the minimization of the energy of the interface between the two phases. For relatively simple crystal structures, this energy minimization occurs when close-packed, or relatively close-packed, rows of atoms match across the interface. Hence, the fundamental principle behind edge-to-edge matching is that the directions in each phase that correspond to the edges of the planes that meet in the interface should be close-packed, or relatively close-packed, rows of atoms. A few of the recently reported examples of what is termed edge-to-edge matching appear to ignore this fundamental principle. By comparing theoretical predictions with available experimental data, this article will explore the validity of this critical atom-row coincidence condition, in situations where the two phases have simple crystal Structures and in those where the precipitate has a more complex structure.

Intragranular nucleation of austenite

The mechanism of intragranular nucleation of austenite in a duplex stainless steel (Fe-23.1 Cr-6.1 Ni-3.1 Mo-O.165 N-0.017 C, wt.%) weld metal and heat-affected zone (HAZ) has been examined. In the weld metal the acicular austenite is found to nucleate intragranularly on inclusions and subsequent plates form sympathetically resulting in a fine interlocked microstructure. Austenite plates adopt the Kurdjumov-Sachs orientation relationship with the ferrite matrix and grow with diffusion-controlled mechanism as evident from partitioning of substitutional alloying elements. At least one set of fine intrinsic dislocations on the austenite/ferrite interphase interfaces is observed suggesting that the boundaries are semi-coherent. The high cooling rates involved in the HAZ result in a supersaturated ferrite matrix where precipitation of intragranular austenite occurs as a result of reheating associated with subsequent passes. Austenite particles in the HAZ nucleate preferentially away from gain boundary austenite allotriomorphs indicating that intragranular precipitation is favoured by the supersaturated matrix.

Modelling, simulation and validation of a twelve-pulse autotransformer rectifier for aerospace applications

A microcap SPICE circuit-level model of a 12-pulse autotransformer based rectifier for an aircraft fuel-pump motor drive is described. The importance of including the nonlinear magnetising inductance of the interphase transformers is illustrated. Small supply voltage distortions are seen to result in current imbalance in the interphase transformers, degrading the rectifier input current, and may lead to infringement of the power quality specification. The model has been validated for various operating supply voltages, frequencies and output powers, against measurements from a 3.75 kW unit.

Laboratory Investigation of Diluted Bitumen Trapping and Dissolution in Gravel

The Canadian economy is largely dependent on the distribution of large volumes of oil to domestic and international markets by a long network of pipelines. Unfortunately, accidents occur, and oil can leak or spill from these pipelines before it reaches its destination. Of particular concern are the long-term consequences of oil spills in freshwater, which include sinking of oil in water and the contamination of sensitive areas, such as where fish (e.g., salmon) deposit their eggs in gravel-dominated river sediments. There is a knowledge gap regarding the fate and behaviour of oil in river sediment. To this end, this study aimed at finding the potential for diluted bitumen (dilbit) oil to become trapped in gravel and to transfer hydrocarbons into water by dissolution, which are harmful to aquatic life. Two sets of laboratory experiments were conducted to simulate conditions of an oil spill on an exposed bank or in shallow water. In the first set, by conducting capillary pressure-saturation (Pc-Sw) experiments it was found that dilbit can enter gravel pores without much resistance and approximately 14% of the pore volume can be occupied by discontinuous single or multipore blobs of dilbit following imbibition of water. Air-water Pc-Sw experiments done in laboratory 1-D columns required gravity correction and could be successfully scaled to predict dilbit-water Pc-Sw curves, except for the trapped amount of dilbit. Trapped dilbit constituents can be dissolved into the water flowing through gravel pores (hyporheic flow) at different velocities. In the second set, dissolution experiments suggested that for the duration of the test, hydrocarbons that cause acute toxicity dissolve rapidly, likely resulting in a decrease in their effective solubility. However, dilbit saturation changed only <2% within that time. Chronically toxic PAH compounds were also detected in the effluent water. The total concentration of all detected PAHs and alkylPAHs exceeded the threshold literature value to protect early-life stage fish. Observations of decreased concentrations with increased aqueous velocities as well as less than equilibrium concentrations indicated that the mass transfer was rate-limited. A correlation was developed for the mass transfer rate coefficient to understand the mass transfer behaviour beyond the conditions used in the experiments, which had a Reynolds number exponent similar to the studies of NAPL dissolution in groundwater.

Low frequency of the TEL/AML1 fusion gene in acute lymphoblastic leukaemia in Spain.

We report on a series of Spanish patients with acute lymphoblastic leukaemia in whom the t(12;21) [TEL/AML1] translocation could not be identified with two sensitive techniques: reverse transcript-polymerase chain reaction (RT-PCR) and fluorescence in-situ hybridization (FISH). 101 cases were analysed: 38 children (29 B-cell precursor; nine T-cell precursor) and 63 adults (48 B-cell precursor; 15 T-cell precursor). Specific RT-PCR to amplify the TEL/AML1 fusion transcript was negative in all 101 cases. Moreover, all 38 paediatric samples were also negative by interphase FISH analysis for the presence of the TEL/AML1 fusion. These results suggest the existence of geographic/race variations in the genotype of acute lymphoblastic leukaemia (ALL).

Artificial Skin - Culturing of Different Skin Cell Lines for Generating an Artificial Skin Substitute on Cross-Weaved Spider Silk Fibres

Background: In the field of Plastic Reconstructive Surgery the development of new innovative matrices for skin repair is in urgent need. The ideal biomaterial should promote attachment, proliferation and growth of cells. Additionally, it should degrade in an appropriate time period without releasing harmful substances, but not exert a pathological immune response. Spider dragline silk from Nephila spp meets these demands to a large extent. Methodology/Principal Findings: Native spider dragline silk, harvested directly out of Nephila spp spiders, was woven on steel frames. Constructs were sterilized and seeded with fibroblasts. After two weeks of cultivating single fibroblasts, keratinocytes were added to generate a bilayered skin model, consisting of dermis and epidermis equivalents. For the next three weeks, constructs in co-culture were lifted on an originally designed setup for air/liquid interface cultivation. After the culturing period, constructs were embedded in paraffin with an especially developed program for spidersilk to avoid supercontraction. Paraffin cross-sections were stained in Haematoxylin & Eosin (H&E) for microscopic analyses. Conclusion/Significance: Native spider dragline silk woven on steel frames provides a suitable matrix for 3 dimensional skin cell culturing. Both fibroblasts and keratinocytes cell lines adhere to the spider silk fibres and proliferate. Guided by the spider silk fibres, they sprout into the meshes and reach confluence in at most one week. A well-balanced, bilayered cocultivation in two continuously separated strata can be achieved by serum reduction, changing the medium conditions and the cultivation period at the air/liquid interphase. Therefore spider silk appears to be a promising biomaterial for the enhancement of skin regeneration.

A two-fluid model for tissue growth within a dynamic flow environment

We study the growth of a tissue construct in a perfusion bioreactor, focussing on its response to the mechanical environment. The bioreactor system is modelled as a two-dimensional channel containing a tissue construct through which a flow of culture medium is driven. We employ a multiphase formulation of the type presented by G. Lemon, J. King, H. Byrne, O. Jensen and K. Shakesheff in their study (Multiphase modelling of tissue growth using the theory of mixtures. J. Math. Biol. 52(2), 2006, 571–594) restricted to two interacting fluid phases, representing a cell population (and attendant extracellular matrix) and a culture medium, and employ the simplifying limit of large interphase viscous drag after S. Franks in her study (Mathematical Modelling of Tumour Growth and Stability. Ph.D. Thesis, University of Nottingham, UK, 2002) and S. Franks and J. King in their study Interactions between a uniformly proliferating tumour and its surrounding: Uniform material properties. Math. Med. Biol. 20, 2003, 47–89). The novel aspects of this study are: (i) the investigation of the effect of an imposed flow on the growth of the tissue construct, and (ii) the inclusion of a chanotransduction mechanism regulating the response of the cells to the local mechanical environment. Specifically, we consider the response of the cells to their local density and the culture medium pressure. As such, this study forms the first step towards a general multiphase formulation that incorporates the effect of mechanotransduction on the growth and morphology of a tissue construct. The model is analysed using analytic and numerical techniques, the results of which illustrate the potential use of the model to predict the dominant regulatory stimuli in a cell population.

SOVLENT REACTIVITY AND INTERFACE EVOLUTION AT MODEL ELECTRODES FOR ENERGY APPLICATIONS

The Li-ion rechargeable battery (LIB) is widely used as an energy storage device, but has significant limitations in battery cycle life and safety. During initial charging, decomposition of the ethylene carbonate (EC)-based electrolytes of the LIB leads to the formation of a passivating layer on the anode known as the solid electrolyte interphase (SEI). The formation of an SEI has great impact on the cycle life and safety of LIB, yet mechanistic aspects of SEI formation are not fully understood. In this dissertation, two surface science model systems have been created under ultra-high vacuum (UHV) to probe the very initial stage of SEI formation at the model carbon anode surfaces of LIB. The first model system, Model System I, is an lithium-carbonate electrolyte/graphite C(0001) system. I have developed a temperature programmed desorption/temperature programmed reaction spectroscopy (TPD/TPRS) instrument as part of my dissertation to study Model System I in quantitative detail. The binding strengths and film growth mechanisms of key electrolyte molecules on model carbon anode surfaces with varying extents of lithiation were measured by TPD. TPRS was further used to track the gases evolved from different reduction products in the early-stage SEI formation. The branching ratio of multiple reaction pathways was quantified for the first time and determined to be 70.% organolithium products vs. 30% inorganic lithium product. The obtained branching ratio provides important information on the distribution of lithium salts that form at the very onset of SEI formation. One of the key reduction products formed from EC in early-stage SEI formation is lithium ethylene dicarbonate (LEDC). Despite intensive studies, the LEDC structure in either the bulk or thin-film (SEI) form is unknown. To enable structural study, pure LEDC was synthesized and subject to synchrotron X-ray diffraction measurements (bulk material) and STM measurements (deposited films). To enable studies of LEDC thin films, Model System II, a lithium ethylene dicarbonate (LEDC)-dimethylformamide (DMF)/Ag(111) system was created by a solution microaerosol deposition technique. Produced films were then imaged by ultra-high vacuum scanning tunneling microscopy (UHV-STM). As a control, the dimethylformamide (DMF)-Ag(111) system was first prepared and its complex 2D phase behavior was mapped out as a function of coverage. The evolution of three distinct monolayer phases of DMF was observed with increasing surface pressure — a 2D gas phase, an ordered DMF phase, and an ordered Ag(DMF)2 complex phase. The addition of LEDC to this mixture, seeded the nucleation of the ordered DMF islands at lower surface pressures (DMF coverages), and was interpreted through nucleation theory. A structural model of the nucleation seed was proposed, and the implication of ionic SEI products, such as LEDC, in early-stage SEI formation was discussed.

Análisis teórico del contacto plasma-superficie y sus aplicaciones industriales

Actualmente, la física de plasmas constituye una parte importante de la investigación en física que está siendo desarrollada. Su campo de aplicación varía desde el estudio de plasmas interestelares y cósmicos, como las estrellas, las nebulosas, el medio intergaláctico, etc.; hasta aplicaciones más terrenales como la producción de microchips o los dispositivos de iluminación. Resulta particularmente interesante el estudio del contacto de una superficie metálica con un plasma. Siendo la razón que, la dinámica de la interfase formada entre un plasma imperturbado y una superficie metálica, resulta de gran importancia cuando se trata de estudiar problemas como: la implantación iónica en una oblea de silicio, el grabado por medio de plasmas, la carga de una aeronave cuando atraviesa la ionosfera y la diagnosis de plasmas mediante sondas de Langmuir. El uso de las sondas de Langmuir está extendido a través de multitud de aplicaciones tecnológicas e industriales como método de diagnosis de plasmas. Algunas de estas aplicaciones han sido mencionadas justo en el párrafo anterior. Es más, su uso también es muy popular en la investigación en física de plasmas, por ser una de las pocas técnicas de diagnosis que proporciona información local sobre el plasma. El equipamiento donde es habitualmente implementado varía desde plasmas de laboratorio de baja temperatura hasta plasmas de fusión en dispositivos como tokamaks o stellerators. La geometría más popular de este tipo de sondas es cilíndrica, y la principal magnitud que se usa para diagnosticar el plasma es la corriente recogida por la sonda cuando se encuentra polarizada a un cierto potencial. Existe un interes especial en diagnosticar por medio de la medida de la corriente iónica recogida por la sonda, puesto que produce una perturbación muy pequeña del plasma en comparación con el uso de la corriente electrónica. Dada esta popularidad, no es de extrañar que grandes esfuerzos se hayan realizado en la consecución de un modelo teórico que explique el comportamiento de una sonda de Langmuir inmersa en un plasma. Hay que remontarse a la primera mitad del siglo XX para encontrar las primeras teorías que permiten diagnosticar parámetros del plasma mediante la medida de la corriente iónica recogida por la sonda de Langmuir. Desde entonces, las mejoras en estos modelos y el desarrollo de otros nuevos ha sido una constante en la investigación en física de plasmas. No obstante, todavía no está claro como los iones se aproximan a la superficie de la sonda. Las dos principales, a la par que opuestas, aproximaciones al problema que están ampliamente aceptadas son: la radial y la orbital; siendo el problema que ambas predicen diferentes valores para la corriente iónica. Los experimentos han arrojado resultados de acuerdo con ambas teorías, la radial y la orbital; y lo que es más importante, una transición entre ambos ha sido recientemente observada. La mayoría de los logros conseguidos a la hora de comprender como los iones caen desde el plasma hacia la superficie de la sonda, han sido llevados a cabo en el campo de la dinámica de fluidos o la teoría cinética. Por otra parte, este problema puede ser abordado mediante el uso de simulaciones de partículas. La principal ventaja de las simulaciones de partículas sobre los modelos de fluidos o cinéticos es que proporcionan mucha más información sobre los detalles microscópicos del movimiento de las partículas, además es relativamente fácil introducir interacciones complejas entre las partículas. No obstante, estas ventajas no se obtienen gratuitamente, ya que las simulaciones de partículas requieren grandísimos recursos. Por esta razón, es prácticamente obligatorio el uso de técnicas de procesamiento paralelo en este tipo de simulaciones. El vacío en el conocimiento de las sondas de Langmuir, es el que motiva nuestro trabajo. Nuestra aproximación, y el principal objetivo de este trabajo, ha sido desarrollar una simulación de partículas que nos permita estudiar el problema de una sonda de Langmuir inmersa en un plasma y que está negativamente polarizada con respecto a éste. Dicha simulación nos permitiría estudiar el comportamiento de los iones en los alrededores de una sonda cilíndrica de Langmuir, así como arrojar luz sobre la transición entre las teorías radiales y orbitales que ha sido observada experimentalmente. Justo después de esta sección introductoria, el resto de la tesis está dividido en tres partes tal y como sigue: La primera parte está dedicada a establecer los fundamentos teóricos de las sondas de Langmuir. En primer lugar, se realiza una introducción general al problema y al uso de sondas de Langmuir como método de diagnosis de plasmas. A continuación, se incluye una extensiva revisión bibliográfica sobre las diferentes teorías que proporcionan la corriente iónica recogida por una sonda. La segunda parte está dedicada a explicar los detalles de las simulaciones de partículas que han sido desarrolladas a lo largo de nuestra investigación, así como los resultados obtenidos con las mismas. Esta parte incluye una introducción sobre la teoría que subyace el tipo de simulaciones de partículas y las técnicas de paralelización que han sido usadas en nuestros códigos. El resto de esta parte está dividido en dos capítulos, cada uno de los cuales se ocupa de una de las geometrías consideradas en nuestras simulaciones (plana y cilíndrica). En esta parte discutimos también los descubrimientos realizados relativos a la transición entre el comportamiento radial y orbital de los iones en los alrededores de una sonda cilíndrica de Langmuir. Finalmente, en la tercera parte de la tesis se presenta un resumen del trabajo realizado. En este resumen, se enumeran brevemente los resultados de nuestra investigación y se han incluido algunas conclusiones. Después de esto, se enumeran una serie de perspectivas futuras y extensiones para los códigos desarrollados.

Karyotype and genome size in Euterpe Mart. (Arecaceae) species.

Euterpe (Martius, 1823), a genus from Central and South America, has species with high economic importance in Brazil, because of their palm heart and fruits, known as açaí berries. Breeding programs have been conducted to increase yield and establish cultivation systems to replace the extraction of wild material. These programs need basic information about the genome of these species to better explore the available genetic variability. The aim of this study was to compare E. edulis (Martius, 1824), E. oleracea (Martius, 1824) and E. precatoria (Martius, 1842), with regard to karyotype, type of interphase nucleus and nuclear DNA amount. Metaphase chromosomes and interphase nuclei from root tip meristematic cells were obtained by the squashing technique and solid stained for microscope analysis. The DNA amount was estimated by flow cytometry. There were previous reports on the chromosome number of E. edulis and E. oleracea, but chromosome morphology of these two species and the whole karyotype of E. precatoria are reported for the first time. The species have 2n=36, a number considered as a pleisomorphic feature in Arecoideae since the modern species, according to floral morphology, have the lowest chromosome number (2n=28 and 2n=30). The three Euterpe species also have the same type of interphase nuclei, classified as semi-reticulate. The species differed on karyotypic formulas, on localization of secondary constriction and genome size. The data suggest that the main forces driving Euterpe karyotype evolution were structural rearrangements, such as inversions and translocations that alter chromosome morphology, and either deletion or amplification that led to changes in chromosome size.

Effects of infiltration pressure on mechanical properties of Al–12Si/graphite composites for piston engines

In this work results for the flexural strength and the thermal properties of interpenetrated graphite preforms infiltrated with Al-12wt%Si are discussed and compared to those for packed graphite particles. To make this comparison relevant, graphite particles of four sizes in the range 15–124 μm, were obtained by grinding the graphite preform. Effects of the pressure applied to infiltrate the liquid alloy on composite properties were investigated. In spite of the largely different reinforcement volume fractions (90% in volume in the preform and around 50% in particle compacts) most properties are similar. Only the Coefficient of Thermal Expansion is 50% smaller in the preform composites. Thermal conductivity of the preform composites (slightly below 100 W/m K), may be increased by reducing the graphite content, alloying, or increasing the infiltration pressure. The strength of particle composites follows Griffith criterion if the defect size is identified with the particle diameter. On the other hand, the composites strength remains increasing up to unusually high values of the infiltration pressure. This is consistent with the drainage curves measured in this work. Mg and Ti additions are those that produce the most significant improvements in performance. Although extensive development work remains to be done, it may be concluded that both mechanical and thermal properties make these materials suitable for the fabrication of piston engines.

One-step amino-functionalization of milled carbon fibre for enhancement of thermo-physical properties of epoxy composites

Development of new chemical approaches for preparation of engineered carbon-based fillers is critical for high-performance applications. Herein, an efficient method for covalent functionalization of polyacrylonitrile-based carbon fibre through azo radical addition under mild condition is demonstrated. In this way, isobutyronitrile radicals in situ produced from thermal decomposition of 2,2′-azobisisobutyronitrile (AIBN), were covalently grafted on milled carbon fibre (MCF) surface, assisted by microwave irradiation, as evidenced by FTIR, Raman, and TGA analysis. The grafted isobutyronitriles on MCF surface (n-MCF) were applied for further MCF amino-functionalization (a-MCF) via nucleophilic reaction of an amine-rich compound. Then, both pure MCF and a-MCF were incorporated into epoxy matrix; and its curing process and thermo-physical properties were investigated using DSC, rheometry, DMA, TGA, and flexural analysis. The Tg and flexural strength of epoxy/a-MCF composites, compared to epoxy/MCF, increased by ∼3.5% and ∼10.2%, resulting from good adhesion between a-MCF and epoxy matrix which confirmed by SEM observations.

A systematic investigation into a novel method for preparing carbon fibre–carbon nanotube hybrid structures

By electrospraying solvent dispersed carbon nanotubes (CNTs) with a binder onto carbon fibre (CF), hybrid structures, with an end aim to improve interfacial bonding in composites, were formed. The electrospray parameters controlling the modification of the CNT morphologies were studied. High-speed camera observations found applied voltage was critical for determining spray mode development. Electric field simulations revealed a concentrated electric field region around each fibre. Both voltage and distance played an important role in determining the CNT morphology by mediating anchoring strength and electric field force. The forming mechanism investigation of different surface morphologies suggested that binder with appropriate wetness gives freedom to the CNTs, allowing them to orientate radially from the CF surface. Linear density (LD) measurements and thermogravimetric analysis revealed that a 10 min coating increased the LD of a single CF filament by up to 31.7% while a 1 h treatment increased fibre bundle mass by 1%.