Influence of concrete strength and length/diameter on the axial capacity of CFT columns

This paper presents an experimental analysis of the confinement effects in steel-concrete composite columns regarding two parameters: concrete compressive strength and column slenderness. Sixteen concrete-filled steel tubular columns with circular cross section were tested under axial loading. The tested columns were filled by concrete with compressive strengths of 30, 60. 80, and 100 MPa, and had length/diameter ratios of 3, 5, 7, and 10. The experimental values of the columns` ultimate load were compared to the predictions of 4 code provisions: the Brazilian Code NBR 8800:2008, Eurocode 4 (EN 1994-1-1:2004), AINSI/AISC 360:2005, and CAN/CSA S16-01:2001. According to the results, the load capacity of the composite columns increased with increasing concrete strength and decreased with increasing length/diameter ratio. In general, the code provisions were highly accurate in the prediction of column capacity. Among them, the Brazilian Code was the most conservative, while Eurocode 4 presented the values closest to the experimental results. (C) 2009 Elsevier Ltd. All rights reserved.

Design of concrete-filled steel tubular columns under axial loading according to NBR 8800:2008 and Eurocode 4:2004: tests results and comparisons

In this paper results of tests on 32 concrete-filled steel tubular columns under axial load are reported. The test parameters were the concrete compressive strength, the column slenderness (L/D) and the wall thickness (t). The test results were compared with predictions from the codes NBR 8800:2008 and EN 1994-1-1:2004 (EC4). The columns were 3, 5, 7 and 10 length to diameter ratios (L/D) and were tested with 30MPa, 60MPa, 80MPa and 100MPa concrete compressive strengths. The results of ultimate strength predicted by codes showed good agreement with experimental results. The results of NBR 8800 code were the most conservative and the EC4 showed the best results, in mean, but it was not conservative for usual concrete-filled short columns.

Fatigue behaviour of friction stir welded AA2024-T3 alloy: longitudinal and transverse crack growth

The fatigue crack growth properties of friction stir welded joints of 2024-T3 aluminium alloy have been studied under constant load amplitude (increasing-Delta K), with special emphasis on the residual stress (inverse weight function) effects on longitudinal and transverse crack growth rate predictions (Glinka`s method). In general, welded joints were more resistant to longitudinally growing fatigue cracks than the parent material at threshold Delta K values, when beneficial thermal residual stresses decelerated crack growth rate, while the opposite behaviour was observed next to K-C instability, basically due to monotonic fracture modes intercepting fatigue crack growth in weld microstructures. As a result, fatigue crack growth rate (FCGR) predictions were conservative at lower propagation rates and non-conservative for faster cracks. Regarding transverse cracks, intense compressive residual stresses rendered welded plates more fatigue resistant than neat parent plate. However, once the crack tip entered the more brittle weld region substantial acceleration of FCGR occurred due to operative monotonic tensile modes of fracture, leading to non-conservative crack growth rate predictions next to K-C instability. At threshold Delta K values non-conservative predictions values resulted from residual stress relaxation. Improvements on predicted FCGR values were strongly dependent on how the progressive plastic relaxation of the residual stress field was considered.

An EFG method for the nonlinear analysis of plates undergoing arbitrarily large deformations

The applicability of a meshfree approximation method, namely the EFG method, on fully geometrically exact analysis of plates is investigated. Based on a unified nonlinear theory of plates, which allows for arbitrarily large rotations and displacements, a Galerkin approximation via MLS functions is settled. A hybrid method of analysis is proposed, where the solution is obtained by the independent approximation of the generalized internal displacement fields and the generalized boundary tractions. A consistent linearization procedure is performed, resulting in a semi-definite generalized tangent stiffness matrix which, for hyperelastic materials and conservative loadings, is always symmetric (even for configurations far from the generalized equilibrium trajectory). Besides the total Lagrangian formulation, an updated version is also presented, which enables the treatment of rotations beyond the parameterization limit. An extension of the arc-length method that includes the generalized domain displacement fields, the generalized boundary tractions and the load parameter in the constraint equation of the hyper-ellipsis is proposed to solve the resulting nonlinear problem. Extending the hybrid-displacement formulation, a multi-region decomposition is proposed to handle complex geometries. A criterium for the classification of the equilibrium`s stability, based on the Bordered-Hessian matrix analysis, is suggested. Several numerical examples are presented, illustrating the effectiveness of the method. Differently from the standard finite element methods (FEM), the resulting solutions are (arbitrary) smooth generalized displacement and stress fields. (c) 2007 Elsevier Ltd. All rights reserved.

Safety of a railway wheelset - derailment simulation with increasing lateral force

The motivation for this research is to make a comparison between dynamic results of a free railway wheelset derailment and safety limits. For this purpose, a numerical simulation of a wheelset derailment submitted to increasing lateral force is used to compare with the safety limit, using different criteria. A simplified wheelset model is used to simulate derailments with different adhesion conditions. The contact force components, including the longitudinal and spin effects, are identified in a steady-state condition on the verge of a derailment. The contact force ratios are used in a three-dimensional (3D) analytical formula to calculate the safety limits. Simulation results obtained with two contact methods were compared with the published results and the safety limit was identified with the two criteria. Results confirm Nadal`s conservative aspect and show that safety 3D analytical formula presents slightly higher safety limits for lower friction coefficients and smaller limits for high friction, in comparison with the simulation results with Fastsim.

Effect of precracking method on K(Ic) results for medium-density polyethylene tested under cryogenic condition

The effect of different precracking methods on the results of linear elastic K(Ic) fracture toughness testing with medium-density polyethylene (MDPE) was investigated. Cryogenic conditions were imposed in order to obtain valid K(Ic) values from specimens of suitable size. Most conservative K(Ic) values were obtained by slow pressing a fresh razor blade at the notch root of the specimen. Due to the low deformation level imposed on the crack tip region, the slow pressing razor blade technique also produced less scatter in fracture toughness results. It has been shown that the slow stable crack growth preceding catastrophic brittle failure during K(Ic) tests in MOPE under cryogenic conditions should not be disregarded as it has relevant physical meaning and may affect the fracture toughness results. (C) 2010 Elsevier Ltd. All rights reserved.

Failure assessments of corroded pipelines with axial defects using stress-based criteria: Numerical studies and verification analyses

Conventional procedures used to assess the integrity of corroded piping systems with axial defects generally employ simplified failure criteria based upon a plastic collapse failure mechanism incorporating the tensile properties of the pipe material. These methods establish acceptance criteria for defects based on limited experimental data for low strength structural steels which do not necessarily address specific requirements for the high grade steels currently used. For these cases, failure assessments may be overly conservative or provide significant scatter in their predictions, which lead to unnecessary repair or replacement of in-service pipelines. Motivated by these observations, this study examines the applicability of a stress-based criterion based upon plastic instability analysis to predict the failure pressure of corroded pipelines with axial defects. A central focus is to gain additional insight into effects of defect geometry and material properties on the attainment of a local limit load to support the development of stress-based burst strength criteria. The work provides an extensive body of results which lend further support to adopt failure criteria for corroded pipelines based upon ligament instability analyses. A verification study conducted on burst testing of large-diameter pipe specimens with different defect length shows the effectiveness of a stress-based criterion using local ligament instability in burst pressure predictions, even though the adopted burst criterion exhibits a potential dependence on defect geometry and possibly on material`s strain hardening capacity. Overall, the results presented here suggests that use of stress-based criteria based upon plastic instability analysis of the defect ligament is a valid engineering tool for integrity assessments of pipelines with axial corroded defects. (C) 2008 Elsevier Ltd. All rights reserved.

A new polymorphism in the Growth and Differentiation Factor 9 (GDF9) gene is associated with increased ovulation rate and prolificacy in homozygous sheep

P>Brazilian Santa Ines (SI) sheep are very well-adapted to the tropical conditions of Brazil and are an important source of animal protein. A high rate of twin births was reported in some SI flocks. Growth and Differentiation Factor 9 (GDF9) and Bone Morphogenetic Protein 15 (BMP15) are the first two genes expressed by the oocyte to be associated with an increased ovulation rate in sheep. All GDF9 and BMP15 variants characterized, until now, present the same phenotype: the heterozygote ewes have an increased ovulation rate and the mutated homozygotes are sterile. In this study, we have found a new allele of GDF9, named FecGE (Embrapa), which leads to a substitution of a phenylalanine with a cysteine in a conservative position of the mature peptide. Homozygote ewes presenting the FecGE allele have shown an increase in their ovulation rate (82%) and prolificacy (58%). This new phenotype can be very useful in better understanding the genetic control of follicular development; the mechanisms involved in the control of ovulation rate in mammals; and for the improvement of sheep production.

Adaptation of an apple sooty blotch and flyspeck warning system for the Upper Midwest United States

A warning system for sooty blotch and flyspeck (SBFS) of apple, developed in the southeastern United States, uses cumulative hours of leaf wetness duration (LWD) to predict the timing of the first appearance of signs. In the Upper Midwest United States, however, this warning system has resulted in sporadic disease control failures. The purpose of the present study was to determine whether the warning system`s algorithm could be modified to provide more reliable assessment of SBFS risk. Hourly LWD, rainfall, relative humidity (RH), and temperature data were collected from orchards in Iowa, North Carolina, and Wisconsin in 2005 and 2006. Timing of the first appearance of SBFS signs was determined by weekly scouting. Preliminary analysis using scatterplots and boxplots suggested that Cumulative hours of RH >= 97% could be a useful predictor of SBFS appearance. Receiver operating characteristic curve analysis was used to compare the predictive performance of cumulative LWD and cumulative hours of RH >= 97%. Cumulative hours of RH >= 97% was a more conservative and accurate predictor than cumulative LWD for 15 site years in the Upper Midwest, but not for four site years in North Carolina. Performance of the SBFS warning system in the Upper Midwest and climatically similar regions may be improved if cumulative hours of RH >= 97% were substituted for cumulative LWD to predict the first appearance of SBFS.

Longitudinal excursion and strain in the median nerve during novel nerve gliding exercises for carpal tunnel syndrome

Nerve and tendon gliding exercises are advocated in the conservative and postoperative management of carpal tunnel syndrome (CTS). However, traditionally advocated exercises elongate the nerve bedding substantially, which may induce a potentially deleterious strain in the median nerve with the risk of symptom exacerbation in some patients and reduced benefits from nerve gliding. This study aimed to evaluate various nerve gliding exercises, including novel techniques that aim to slide the nerve through the carpal tunnel while minimizing strain (sliding techniques). With these sliding techniques, it is assumed that an increase in nerve strain due to nerve bed elongation at one joint (e.g., wrist extension) is simultaneously counterbalanced by a decrease in nerve bed length at an adjacent joint (e.g., elbow flexion). Excursion and strain in the median nerve at the wrist were measured with a digital calliper and miniature strain gauge in six human cadavers during six mobilization techniques. The sliding technique resulted in an excursion of 12.4 mm, which was 30% larger than any other technique (p 0.0002). Strain also differed between techniques (p 0.00001), with minimal peak values for the sliding technique. Nerve gliding associated with wrist movements can be considerably increased and nerve strain substantially reduced by simultaneously moving neighboring joints. These novel nerve sliding techniques are biologically plausible exercises for CTS that deserve further clinical evaluation. © 2007 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 25:972-980, 2007

A randomised control trial of exercise and manipulative therapy for cervicogenic headache

Study Design. A multicenter, randomized controlled trial with unblinded treatment and blinded outcome assessment was conducted. The treatment period was 6 weeks with follow-up assessment after treatment, then at 3, 6, and 12 months. Objectives. To determine the effectiveness of manipulative therapy and a low-load exercise program for cervicogenic headache when used alone and in combination, as compared with a control group. Summary of Background Data. Headaches arising from cervical musculoskeletal disorders are common. Conservative therapies are recommended as the first treatment of choice. Evidence for the effectiveness of manipulative therapy is inconclusive and available only for the short term. There is no evidence for exercise, and no study has investigated the effect of combined therapies for cervicogenic headache. Methods. In this study, 200 participants who met the diagnostic criteria for cervicogenic headache were randomized into four groups: manipulative therapy group, exercise therapy group, combined therapy group, and a control group. The primary outcome was a change in headache frequency. Other outcomes included changes in headache intensity and duration, the Northwick Park Neck Pain Index, medication intake, and patient satisfaction. Physical outcomes included pain on neck movement, upper cervical joint tenderness, a craniocervical flexion muscle test, and a photographic measure of posture. Results. There were no differences in headache-related and demographic characteristics between the groups at baseline. The loss to follow-up evaluation was 3.5%. At the 12-month follow-up assessment, both manipulative therapy and specific exercise had significantly reduced headache frequency and intensity, and the neck pain and effects were maintained (P < 0.05 for all). The combined therapies was not significantly superior to either therapy alone, but 10% more patients gained relief with the combination. Effect sizes were at least moderate and clinically relevant. Conclusion. Manipulative therapy and exercise can reduce the symptoms of cervicogenic headache, and the effects are maintained.

Improving wheat simulation capabilities in Australia from a cropping systems perspective - III. The integrated wheat model (I_WHEAT)

Previous work has identified several short-comings in the ability of four spring wheat and one barley model to simulate crop processes and resource utilization. This can have important implications when such models are used within systems models where final soil water and nitrogen conditions of one crop define the starting conditions of the following crop. In an attempt to overcome these limitations and to reconcile a range of modelling approaches, existing model components that worked demonstrably well were combined with new components for aspects where existing capabilities were inadequate. This resulted in the Integrated Wheat Model (I_WHEAT), which was developed as a module of the cropping systems model APSIM. To increase predictive capability of the model, process detail was reduced, where possible, by replacing groups of processes with conservative, biologically meaningful parameters. I_WHEAT does not contain a soil water or soil nitrogen balance. These are present as other modules of APSIM. In I_WHEAT, yield is simulated using a linear increase in harvest index whereby nitrogen or water limitations can lead to early termination of grainfilling and hence cessation of harvest index increase. Dry matter increase is calculated either from the amount of intercepted radiation and radiation conversion efficiency or from the amount of water transpired and transpiration efficiency, depending on the most limiting resource. Leaf area and tiller formation are calculated from thermal time and a cultivar specific phyllochron interval. Nitrogen limitation first reduces leaf area and then affects radiation conversion efficiency as it becomes more severe. Water or nitrogen limitations result in reduced leaf expansion, accelerated leaf senescence or tiller death. This reduces the radiation load on the crop canopy (i.e. demand for water) and can make nitrogen available for translocation to other organs. Sensitive feedbacks between light interception and dry matter accumulation are avoided by having environmental effects acting directly on leaf area development, rather than via biomass production. This makes the model more stable across environments without losing the interactions between the different external influences. When comparing model output with models tested previously using data from a wide range of agro-climatic conditions, yield and biomass predictions were equal to the best of those models, but improvements could be demonstrated for simulating leaf area dynamics in response to water and nitrogen supply, kernel nitrogen content, and total water and nitrogen use. I_WHEAT does not require calibration for any of the environments tested. Further model improvement should concentrate on improving phenology simulations, a more thorough derivation of coefficients to describe leaf area development and a better quantification of some processes related to nitrogen dynamics. (C) 1998 Elsevier Science B.V.

Predictors of local recurrence after treatment of ductal carcinoma in situ - A meta-analysis

lBACKGROUND. Management of patients with ductal carcinoma in situ (DCIS) is a dilemma, as mastectomy provides nearly a 100% cure rate but at the expense of physical and psychologic morbidity. It would be helpful if we could predict which patients with DCIS are at sufficiently high risk of local recurrence after conservative surgery (CS) alone to warrant postoperative radiotherapy (RT) and which patients are at sufficient risk of local recurrence after CS + RT to warrant mastectomy. The authors reviewed the published studies and identified the factors that may be predictive of local recurrence after management by mastectomy, CS alone, or CS + RT. METHODS. The authors examined patient, tumor, and treatment factors as potential predictors for local recurrence and estimated the risks of recurrence based on a review of published studies. They examined the effects of patient factors (age at diagnosis and family history), tumor factors (sub-type of DCIS, grade, tumor size, necrosis, and margins), and treatment (mastectomy, CS alone, and CS + RT). The 95% confidence intervals (CI) of the recurrence rates for each of the studies were calculated for subtype, grade, and necrosis, using the exact binomial; the summary recurrence rate and 95% CI for each treatment category were calculated by quantitative meta-analysis using the fixed and random effects models applied to proportions. RESULTS, Meta-analysis yielded a summary recurrence rate of 22.5% (95% CI = 16.9-28.2) for studies employing CS alone, 8.9% (95% CI = 6.8-11.0) for CS + RT, and 1.4% (95% CI = 0.7-2.1) for studies involving mastectomy alone. These summary figures indicate a clear and statistically significant separation, and therefore outcome, between the recurrence rates of each treatment category, despite the likelihood that the patients who underwent CS alone were likely to have had smaller, possibly low grade lesions with clear margins. The patients with risk factors of presence of necrosis, high grade cytologic features, or comedo subtype were found to derive the greatest improvement in local control with the addition of RT to CS. Local recurrence among patients treated by CS alone is approximately 20%, and one-half of the recurrences are invasive cancers. For most patients, RT reduces the risk of recurrence after CS alone by at least 50%. The differences in local recurrence between CS alone and CS + RT are most apparent for those patients with high grade tumors or DCIS with necrosis, or of the comedo subtype, or DCIS with close or positive surgical margins. CONCLUSIONS, The authors recommend that radiation be added to CS if patients with DCIS who also have the risk factors for local recurrence choose breast conservation over mastectomy. The patients who may be suitable for CS alone outside of a clinical trial may be those who have low grade lesions with little or no necrosis, and with clear surgical margins. Use of the summary statistics when discussing outcomes with patients may help the patient make treatment decisions. Cancer 1999;85:616-28. (C) 1999 American Cancer Society.

Review of "Comorbidity, disability and the need for treatment for DSM-IV psychiatric disorders in an insured population"

Background: This study presents estimates of 12 month and current prevalences of DSM-IV disorders, and the related comor-bidity, disability and service utilization, derived from a national probability sample in Australia. Methods: The DSM-IV psychiatric disorders among persons aged 18 and over in the Australian population were assessed with data collected by lay interviewers using the Composite International Diagnostic Interview, other screening interviews and measures of disability and service utilization. The response rate was 78.1% and the final sample size was 10,641 adults. Results: Close to 20% reported at least one twelve month disorder and 13% a disorder current within the past 30 days. ICD-10 diagnoses were also derived, DSM-IV was the more conservative classification whether or not the new clinical significance criteria was applied. Major depression, any personality disorder, and alcohol dependence were the three most common twelve month disorders, generalized anxiety disorder replaced alcohol dependence as the third most common current disorder. The sexes has similar rates of any disorder, but women had higher rates of affective and anxiety disorders, men higher rates of substance use disorders. Prevalence of most disorders declined with age and education, and were lower among those employed or married. Respondents whose symptoms met criteria for three or more disorders in the past year had greatly increased rates of disability and of mental health consultations. The affective and somatoform disorders were associated with the highest rates of disability. Only 36% of people with a mental disorder this year had consulted for a mental problem, and most had seen a general practitioner. We identified those with a current disorder who were disabled or multiply comorbid - only half had consulted and of those who had not, more than half said they did not need treatment. Conclusions: The 12 month prevalence was lower than reported in the US National Comorbidity Survey but method factors might account for this. The relationships between prevalence and demographic variables, and between comorbidity, disability and service utilization were similar to those found in the US survey. Australia has a national health insurance scheme with total coverage and access to medical help is available to all, commonly at little or no cost. We identify the high rate of not consulting among those with a current disorder, and additional disability or multiple comorbidity, as an important public health problem. Kessler argued for more research on barriers to professional help seeking. This report reinforces his conclusion and shows that economic barriers are not the dominant issue.

Management of canine diabetes

The majority of diabetic dogs appear to have a form of type 1 diabetes analogous to the latent autoimmune diabetes of adults (LADA) in humans. Evidence of acute or chronic pancreatitis occurs in about 40% of diabetic dogs. Blindness caused by cataract formation eventually occurs in the majority of diabetic dogs and is not dependent on glycemic control. Insulin is the mainstay of therapy for diabetic dogs, and a conservative approach to insulin therapy is crucial. Most diabetic dogs require twice-daily dosing with lente or NPH insulin to adequately control their clinical signs. The diet fed should primarily be palatable and nutritionally balanced. Improved glycemic control may be achieved in some dogs if the diet contains increased insoluble fiber.