Investigations of cohesive zone properties of the interface between metal film and ceramic substrate at nano- and micro-scales

Cohesive zone characterizations of the interface between metal film and ceramic substrate at micro- and nano-scales are performed in the present research. At the nano-scale, a special potential for special material interface (Ag/MgO) is adopted to investigate the interface separation mechanism by using MD simulation, and stress-separation relationship will be obtained. At the micro-scale, peeling experiment is performed for the Al film/Al2O3 substrate system with an adhesive layer at the interface. Adhesive is a mixture of epoxy and polyimide with mass ratio 1:1, by which a brittle cohesive property is obtained. The relationships between energy release rate, the film thickness and the adhesive layer thickness are measured during the steady-state peeling. The experimental result has a similar trend as modeling result for a weak adhesion interface case.

Cruise Report 58S5-Waste Disposal

(PDF contains 5 pages.)

Tracing the Basque presence in eastern Canada during the 16th and 17th centuries, through ceramic remains: the example of the glazed pottery produced in Bilbao

Poster presentado en Society for Post-Medieval Archaeology Conference, in St John's, Newfoundland,(Canadá)(June 2010)

Determination Of Interfacial Properties Between Metal Film And Ceramic Substrate With An Adhesive Layer

Peel test measurements and inverse analysis to determine the interfacial mechanical parameters for the metal film/ceramic system are performed, considering that there exist an epoxy interface layer between film and ceramic. In the present investigation, Al films with a series of thicknesses between 20 and 250 mu m and three peel angles of 90, 135 and 180 degrees are considered. A finite element model with the cohesive zone elements is used to simulate the peel test process. The finite element results are taken as the training data of a neural network in the inverse analysis. The interfacial cohesive energy and the separation strength can be determined based on the inverse analysis and peel experimental result. (C) 2008 Elsevier Ltd. All rights reserved.

Mechanisms of thermal shock failure for ultra-high temperature ceramic

The materials considered in our analysis were ZrB2 ceramic matrix composites. Effect of two different additives (graphite and AlN) on thermal shock stability for the materials was measured by water quench test. It showed that it may provide more stable thermal shock properties with additives of graphite. It was explained by different thermal properties and crack resistance of the two materials in detail. Surface oxidation was one of main reasons for strength degradation of ceramic with additives of graphite after quenched in water, and surface crack was one of main reasons for strength degradation of ceramic with additives of AlN after quenched in water. It was presented that it was a potential method for improving thermal shock stability of ZrB2 ceramic matrix composites by introducing proper quantities of graphite.

Utilization of waste waters in fish production: preliminary results from fish culture studies in floating cages in a sewage pond, New Bussa, Nigeria

The utilization of waste waters in aquaculture were briefly reviewed. At the National Institute for Freshwater Fisheries Research (NIFFR), stocking density (20 to 160 fish/m super(3)) experiments using Sarotherodon galilaeus (without supplementary feeding) in floating cages were carried out in a sewage pond (0.4ha surface area). Cage culture of S. galilaeus was observed to have potentials in waste waters aquaculture. Recommendations were made on the execution of an intergrated waste water management and utilization.

Experimental Study Of Multi-Hole Cooling For Integrally-Woven, Ceramic Matrix Composite Walls For Gas Turbine Applications

In this paper, multi-hole cooling is studied for an oxide/oxide ceramic specimen with normal injection holes and for a SiC/SiC ceramic specimen with oblique injection holes. A special purpose heat transfer tunnel was designed and built, which can provide a wide range of Reynolds numbers (10(5)similar to 10(7)) and a large temperature ratio of the primary flow to the coolant (up to 2.5). Cooling effectiveness determined by the measured surface temperature for the two types of ceramic specimens is investigated. It is found that the multi-hole cooling system for both specimens has a high cooling efficiency and it is higher for the SiC/SiC specimen than for the oxide/oxide specimen. Effects on the cooling effectiveness of parameters including blowing ratio, Reynolds number and temperature ratio, are studied. In addition, profiles of the mean velocity and temperature above the cooling surface are measured to provide further understanding of the cooling process. Duplication of the key parameters for multi-hole cooling, for a representative combustor flow condition (without radiation effects), is achieved with parameter scaling and the results show the high efficiency of multi-hole cooling for the oblique hole, SiC/SiC specimen. (C) 2008 Elsevier Ltd. All rights reserved.

Possible inclusion of fish waste (scales and fins) in the diet of fishes in aquaculture

The scales and fins of some freshwater fish species (Sarotherodon galilaeus, Oreochromis niloticus, Tilapia zillii, Barbus callipterus, Hemichromis fasciatus) from Kainji Lake, Nigeria were analyzed for their organic and inorganic matter. The aim of such study is to determine the usefulness of these waste parts of the fish in fish feed preparation. In all instances, the inorganic matter was found to be quite high in the fish exoskeleton, and calcium formed the highest element in the scales and the fins. These waste materials are therefore, considered as possible replacement for mineral sources in fish feed and probably the feed for other livestock

Commercial production of fish meal from fish waste

The importance of fish meal production as a means of reducing fish waste currently being experienced in the fisheries subsector is discussed. Cost estimate for Nigeria establishing a fish meal manufacturing plant and suggestions on rational execution of the project are presented. If properly located and well managed, the project will serve to convert fish waste to cash in the industrial fishery

Commercial pond fish culture using waste water

Waste water from some National Electric Power Authority (NEPA) housing units in Nigeria was fed to a 0.4 ha pond which was stocked with 2,200 Sarotherodon galilaeus fingerlings with a mean weight of about 36.0gm and 1000 Cyprinus carpio fingerlings with a mean weight of 10gm. This yielded after 10 months, over 2300 kg of harvestable fish plus over 20,000 Sarotherodon galilaeus fingerlings. The growth rate of C. carpio was not very encouraging possibly because of the type of plankton that colonised the pond. The S. galilaeus became stunted because of overpopulation as there were no carnivores to control their excessive breeding. The physico-chemical parameters were favourable for the growth of fish food organisms

Feeding and waste management strategies in the culture of Clarias gariepinus

Nutrient digestibility and amino acid availability were assessed in sharp-toothed catfish, Clarias gariepinus, fingerlings fed diets containing soyabean flour (SF) - Poultry meat meal (PMM) blends (25:75. 50:50, and 75:25) and 0.5 of 1.0%, Cr sub(2)0 sub(3). There was agreement between the pattern of overall protein digestibility and average amino acid availability despite the variability in individual amino acid availability the best dry matter, lipid and protein digestibility coefficients, and amino acid availability values were obtained with diets containing 0.5% Cr sub(2)0 sub(3). Chromic Oxide inclusion level appeared to affect nutrient availability. Increased marker level resulted into decreased nutrient digestibility coefficients. Similarly, these diets generated lower fecal crude protein than those with 1.0% Cr sub(2)0 sub(3). However, the latter group recorded higher protein retention efficiency. Dry mailer and lipid of diets containing more soyabean flour seemed to be more digestible than those of poultry meat meal. Similar trend was observed for the apparent availability of the amino acids. This investigation has indicated that low level of marker was better in digestibility study. Utilization of more SF than PMM in the diets of this catfish was more beneficial and should be encouraged in the feed industries producing catfish diets towards a better feed and waste management strategies in this aquaculture operation

THE FORMATION MECHANISM OF THE VITRIFIED SLAG IN A PLASMA ARC REACTOR FOR HAZARDOUS WASTE TREATMENT

Various hazardous wastes with additives have been vitrified to investigate the formation mechanism of the glassy slag by a 30 kW DC plasma-arc reactor developed by the Institute of Mechanics, Chinese Academy of Sciences. The average temperature in the reaction area is controlled at 1500°C. The chemical compositions of three sorts of fly ashes are analyzed by XRF (X-Ray Fluorescence). Fly ashes with vitrifying additives can be vitrified to form glassy slag, which show that the ratio of the whole oxygen ions to the whole network former ions in glass (R) is appropriate in the range of 2~3 to form durable vitrified slag. In this experiment, the arc power is controlled below 5 kW to inhibit waste evaporation. To enhance the effects of heat transfer to wastes, ferrous powder has been added into the graphite crucible, which aggregates as ingot below the molten silicate after vitrification. The slag fails to form glass if the quenching rate is less than 1 K/min. Therefore, the slag will break into small chips due to the sharp quenching rate, which is more than 100 K/sec.