ELECTROCHEMICAL OXIDATION OF THE HERBICIDE TEBUTHIURON USING DSA (R)-TYPE ELECTRODE

ELECTROCHEMICAL OXIDATION OF THE HERBICIDE TEBUTHIURON USING DSA (R)-TYPE ELECTRODE. Tebuthiuron (TBH) is a herbicide widely used in different cultures and known for its toxic effects. Electrochemical methods are promising for removing pollutants such as pesticides. This study showed the degradation of TBH using a DSA (R) anode operated at current densities of 50 to 200 mA cm(-2). Removal presented pseudo-first order kinetics while high-pressure liquid chromatography (UV detection) showed two peaks, ascribed to degradation intermediates. The maximum percentage of total organic carbon removed was 12.9%. Ion chromatography revealed that higher concentrations of nitrate and nitrite ions formed with increasing current density.

Urban air pollution: a representative survey of PM2.5 mass concentrations in six Brazilian cities

In urban areas of Brazil, vehicle emissions are the principal source of fine particulate matter (PM2.5). The World Health Organization air quality guidelines state that the annual mean concentration of PM2.5 should be below 10 mu g m(-3). In a collaboration of Brazilian institutions, coordinated by the University of Sao Paulo School of Medicine and conducted from June 2007 to August 2008, PM2.5 mass was monitored at sites with high traffic volumes in six Brazilian state capitals. We employed gravimetry to determine PM2.5 mass concentrations, reflectance to quantify black carbon concentrations, X-ray fluorescence to characterize elemental composition, and ion chromatography to determine the composition and concentrations of anions and cations. Mean PM2.5 concentrations and proportions of black carbon (BC) in the cities of Sao Paulo, Rio de Janeiro, Belo Horizonte, Curitiba, Recife, and Porto Alegre were 28.1 +/- 13.6 mu g m(-3) (38% BC), 17.2 +/- 11.2 mu g m(-3) (20% BC), 14.7 +/- 7.7 mu g m(-3) (31% BC), 14.4 +/- 9.5 mu g m(-3) (30% BC), 7.3 +/- 3.1 mu g m(-3) (26% BC), and 13.4 +/- 9.9 mu g m(-3) (26% BC), respectively. Sulfur and minerals (Al, Si, Ca, and Fe), derived from fuel combustion and soil resuspension, respectively, were the principal elements of the PM2.5 mass. We discuss the long-term health effects for each metropolitan region in terms of excess mortality risk, which translates to greater health care expenditures. This information could prove useful to decision makers at local environmental agencies.

Vehicle emissions and PM2.5 mass concentrations in six Brazilian cities

In Brazil, the principal source of air pollution is the combustion of fuels (ethanol, gasohol, and diesel). In this study, we quantify the contributions that vehicle emissions make to the urban fine particulate matter (PM2.5) mass in six state capitals in Brazil, collecting data for use in a larger project evaluating the impact of air pollution on human health. From winter 2007 to winter 2008, we collected 24-h PM2.5 samples, employing gravimetry to determine PM2.5 mass concentrations; reflectance to quantify black carbon concentrations; X-ray fluorescence to characterize elemental composition; and ion chromatography to determine the composition and concentrations of anions and cations. Mean PM2.5 concentrations in the cities of Sao Paulo, Rio de Janeiro, Belo Horizonte, Curitiba, Porto Alegre, and Recife were 28, 17.2, 14.7, 14.4, 13.4, and 7.3 mu g/m(3), respectively. In Sao Paulo and Rio de Janeiro, black carbon explained approximately 30% of the PM2.5 mass. We used receptor models to identify distinct source-related PM2.5 fractions and correlate those fractions with daily mortality rates. Using specific rotation factor analysis, we identified the following principal contributing factors: soil and crustal material; vehicle emissions and biomass burning (black carbon factor); and fuel oil combustion in industries (sulfur factor). In all six cities, vehicle emissions explained at least 40% of the PM2.5 mass. Elemental composition determination with receptor modeling proved an adequate strategy to identify air pollution sources and to evaluate their short- and long-term effects on human health. Our data could inform decisions regarding environmental policies vis-a-vis health care costs.

Determination of chlorine in food samples via the AlCl molecule using high-resolution continuum source molecular absorption spectrometry in a graphite furnace

Determination of chlorine using the molecular absorption of aluminum mono-chloride (AlCl) at the 261.418 nm wavelength was accomplished by high-resolution continuum source molecular absorption spectrometry using a transversely heated graphite tube furnace with an integrated platform. For the analysis. 10 mu L of the sample followed by 10 mu L of a solution containing Al-Ag-Sr modifier, (1 g L-1 each), were directly injected onto the platform. A spectral interference due to the use of Al-Ag-Sr as mixed modifier was easily corrected by the least-squares algorithm present in the spectrometer software. The pyrolysis and vaporization temperatures were 500 degrees C and 2200 degrees C, respectively. To evaluate the feasibility of a simple procedure for the determination of chlorine in food samples present in our daily lives, two different digestion methods were applied, namely (A) an acid digestion method using HNO3 only at room temperature, and (B) a digestion method with Ag, HNO3 and H2O2, where chlorine is precipitated as a low-solubility salt (AgCl), which is then dissolved with ammonia solution. The experimental results obtained with method B were in good agreement with the certified values and demonstrated that the proposed method is more accurate than method A. This is because the formation of silver chloride prevented analyte losses by volatilization. The limit of detection (LOD, 3 sigma/s) for Cl in methods A and B was 18 mu g g(-1) and 9 mu g g(-1), respectively, 1.7 and 3.3 times lower compared to published work using inductively coupled plasma optical emission spectrometry, and absolute LODs were 2.4 and 1.2 ng, respectively. (C) 2012 Elsevier B.V. All rights reserved.

Chemical and morphological characterization of sugarcane bagasse submitted to a delignification process for enhanced enzymatic digestibility

Abstract Background In recent years, biorefining of lignocellulosic biomass to produce multi-products such as ethanol and other biomaterials has become a dynamic research area. Pretreatment technologies that fractionate sugarcane bagasse are essential for the successful use of this feedstock in ethanol production. In this paper, we investigate modifications in the morphology and chemical composition of sugarcane bagasse submitted to a two-step treatment, using diluted acid followed by a delignification process with increasing sodium hydroxide concentrations. Detailed chemical and morphological characterization of the samples after each pretreatment condition, studied by high performance liquid chromatography, solid-state nuclear magnetic resonance, diffuse reflectance Fourier transformed infrared spectroscopy and scanning electron microscopy, is reported, together with sample crystallinity and enzymatic digestibility. Results Chemical composition analysis performed on samples obtained after different pretreatment conditions showed that up to 96% and 85% of hemicellulose and lignin fractions, respectively, were removed by this two-step method when sodium hydroxide concentrations of 1% (m/v) or higher were used. The efficient lignin removal resulted in an enhanced hydrolysis yield reaching values around 100%. Considering the cellulose loss due to the pretreatment (maximum of 30%, depending on the process), the total cellulose conversion increases significantly from 22.0% (value for the untreated bagasse) to 72.4%. The delignification process, with consequent increase in the cellulose to lignin ratio, is also clearly observed by nuclear magnetic resonance and diffuse reflectance Fourier transformed infrared spectroscopy experiments. We also demonstrated that the morphological changes contributing to this remarkable improvement occur as a consequence of lignin removal from the sample. Bagasse unstructuring is favored by the loss of cohesion between neighboring cell walls, as well as by changes in the inner cell wall structure, such as damaging, hole formation and loss of mechanical resistance, facilitating liquid and enzyme access to crystalline cellulose. Conclusions The results presented herewith show the efficiency of the proposed method for improving the enzymatic digestibility of sugarcane bagasse and provide understanding of the pretreatment action mechanism. Combining the different techniques applied in this work warranted thorough information about the undergoing morphological and chemical changes and was an efficient approach to understand the morphological effects resulting from sample delignification and its influence on the enhanced hydrolysis results.

Oxidação eletroquímica do herbicida tebutiuron utilizando eletrodo do tipo DSA

Tebuthiuron (TBH) is a herbicide widely used in different cultures and known for its toxic effects. Electrochemical methods are promising for removing pollutants such as pesticides. This study showed the degradation of TBH using a DSA® anode operated at current densities of 50 to 200 mA cm-2. Removal presented pseudo-first order kinetics while high-pressure liquid chromatography (UV detection) showed two peaks, ascribed to degradation intermediates. The maximum percentage of total organic carbon removed was 12.9%. Ion chromatography revealed that higher concentrations of nitrate and nitrite ions formed with increasing current density.

Multi-pollutants impact on modern cement built heritage

It is well known that the deposition of gaseous pollutants and aerosols plays a major role in causing the deterioration of monuments and built cultural heritage in European cities. Despite of many studies dedicated to the environmental damage of cultural heritage, in case of cement mortars, commonly used in the 20th century architecture, the deterioration due to air multipollutants impact, especially the formation of black crusts, is still not well explored making this issue a challenging area of research. This work centers on cement mortars – environment interactions, focusing on the diagnosis of the damage on the modern built heritage due to air multi-pollutants. For this purpose three sites, exposed to different urban areas in Europe, were selected for sampling and subsequent laboratory analyses: Centennial Hall, Wroclaw (Poland), Chiesa dell'Autostrada del Sole, Florence (Italy), Casa Galleria Vichi, Florence (Italy). The sampling sessions were performed taking into account the height from the ground level and protection from rain run off (sheltered, partly sheltered and exposed areas). The complete characterization of collected damage layer and underlying materials was performed using a range of analytical techniques: optical and scanning electron microscopy, X ray diffractometry, differential and gravimetric thermal analysis, ion chromatography, flash combustion/gas chromatographic analysis, inductively coupled plasma-optical emission spectrometer. The data were elaborated using statistical methods (i.e. principal components analyses) and enrichment factor for cement mortars was calculated for the first time. The results obtained from the experimental activity performed on the damage layers indicate that gypsum, due to the deposition of atmospheric sulphur compounds, is the main damage product at surfaces sheltered from rain run-off at Centennial Hall and Casa Galleria Vichi. By contrast, gypsum has not been identified in the samples collected at Chiesa dell'Autostrada del Sole. This is connected to the restoration works, particularly surface cleaning, regularly performed for the maintenance of the building. Moreover, the results obtained demonstrated the correlation between the location of the building and the composition of the damage layer: Centennial Hall is mainly undergoing to the impact of pollutants emitted from the close coal power stations, whilst Casa Galleria Vichi is principally affected by pollutants from vehicular exhaust in front of the building.

Tropospheric carboxylic acids in tropical rainforest environments

Der Übergang der Grenzschicht von stark ozeanisch auf kontinental beeinflusst wurde in 2 tropischen Küstenwaldgebieten Amerikas untersucht, wo Luftmassen vom Meer kommend über den Kontinent transportiert werden.Zwei Feldkampagnen wurden durchgeführt; in Costa Rica (CR; 07.1996) und in Surinam (04.1998). In CR wurde im nordöstlichen Flachgebiet (etwa 10°25' N; 84°W) Regenwasser gesammelt, in dem später Carboxylate, anorganischen Anionen, Ca2+, K+, NH4+ und Mg2+ gemessen wurden. Die Proben wurden an 5 verschiedenen Stellen entlang der Windrichtung 1, 20, 60, 60 und 80 km von der Küste gesammelt. In Surinam (Sipaliwini, 2°02' N, 56°08' W) wurden organischen Säuren aus der Gasphase gesammelt etwa 550 km von der Küste entfernt, sowohl wie O3 und CO. Die Proben wurden mittels Ionenchromatographie und Kapillarelektrophorese analysiert. Morgendliche Einmischung der nächtlichen residualen Schicht und Luft der unteren freien Troposphäre war Hauptquelle für HCOOH und CH3COOH in der Tagesmischschicht. Es wurde gezeigt, dass lokale Produktion dieser Säuren durch chemische Reaktionen eine kleine Rolle gespielt hat und dass direkte Emission vernachlässigbar war.Aus den beiden Feldkampagnen folgt, dass die Konzentrationen der sekundären Verbindungen HCOOH, CH3COOH, Ozon und CO in der Tagesmischschicht von Importen bestimmt wurden, was gilt für Regen- und Trockenzeit bis zu Entfernungen von 550 km zur Küste.

Beiträge zur Chemie der schwersten Elemente in den Bereichen Elektrochemie und Chromatographie

Im Rahmen dieser Arbeit wurden Experimente auf verschiedenen Gebieten der chemischen Charakterisierung der schwersten Elemente durchgeführt. So wurden Vorarbeiten zur Elektrochemie der superschweren Elemente geleistet. Hier konnte gezeigt werden, dass sich Po aus verdünnten Säuren auf Metallelektroden spontan abscheiden lässt. Als wichtigste Reaktionsparameter wurden Temperatur, Konvektion und Viskosität des Elektrolyten identifiziert. Für die Elektrodeposition ist es von Bedeutung, reproduzierbar saubere Elektroden einzusetzen. Auch hierzu konnten Erkenntnisse gewonnen werden. Auf dem Gebiet der Charakterisierung von Nukliden wurde der Elektroneneinfang in Db-263 untersucht. Aus diesem Zerfall geht Rf-263 hervor, welches mit einer Halbwertszeit von 15min überwiegend durch Spontanspaltung zerfällt. Im Experiment wurde Rf-263 mittels Ionenaustauschchromatographie und nachfolgender Flüssig-Flüssig-Extraktion von Db und Aktiniden getrennt. Das erhaltene Präparat wurde auf Alpha-Zerfall und Spontanspaltung untersucht. Die Zahl der Rf-263 Zerfälle lässt auf einen Zerfallszweig durch Elektroneneinfang in Db-263 von 3% schließen. Ein Großteil der Arbeit beschäftigt sich mit der Bestimmung des Kd-Wertes von Sg am Anionenaustauscher Aminex A27 in 0.1M HNO3/5E-3M HF. Beim mit dem ALOHA-System durchgeführten Experiment wurde die Mehrsäulentechnik (MCT) erstmals für die wässrige Chemie von Sg genutzt. Aufgrund zahlreicher Probleme konnte letztlich kein Kd-Wert bestimmt werden. Stattdessen wurde das Experiment einer Fehleranalyse unterzogen. Hier zeigte sich eine Anfälligkeit der MCT auf natürliche Radionuklide. Weiterhin konnten Probleme bei ALOHA aufgedeckt werden, die eine Wiederholung des Experiments ausschlossen. In der Folge wurde ein alternativer Anionenaustauscher charakterisiert, sowie die Elektrolysebedingungen, als wichtiger Schritt der chemischen Aufarbeitung bei der MCT, genauer spezifiziert.

Iodine speciation in atmospheric aerosols in the marine boundary layer

Iodine chemistry plays an important role in the tropospheric ozone depletion and the new particle formation in the Marine Boundary Layer (MBL). The sources, reaction pathways, and the sinks of iodine are investigated using lab experiments and field observations. The aims of this work are, firstly, to develop analytical methods for iodine measurements of marine aerosol samples especially for iodine speciation in the soluble iodine; secondly, to apply the analytical methods in field collected aerosol samples, and to estimate the characteristics of aerosol iodine in the MBL. Inductively Coupled Plasma – Mass Spectrometry (ICP-MS) was the technique used for iodine measurements. Offline methods using water extraction and Tetra-methyl-ammonium-hydroxide (TMAH) extraction were applied to measure total soluble iodine (TSI) and total insoluble iodine (TII) in the marine aerosol samples. External standard calibration and isotope dilution analysis (IDA) were both conducted for iodine quantification and the limits of detection (LODs) were both 0.1 μg L-1 for TSI and TII measurements. Online couplings of Ion Chromatography (IC)-ICP-MS and Gel electrophoresis (GE)-ICP-MS were both developed for soluble iodine speciation. Anion exchange columns were adopted for IC-ICP-MS systems. Iodide, iodate, and unknown signal(s) were observed in these methods. Iodide and iodate were separated successfully and the LODs were 0.1 and 0.5 μg L-1, respectively. Unknown signals were soluble organic iodine species (SOI) and quantified by the calibration curve of iodide, but not clearly identified and quantified yet. These analytical methods were all applied to the iodine measurements of marine aerosol samples from the worldwide filed campaigns. The TSI and TII concentrations (medians) in PM2.5 were found to be 240.87 pmol m-3 and 105.37 pmol m-3 at Mace Head, west coast of Ireland, as well as 119.10 pmol m-3 and 97.88 pmol m-3 in the cruise campaign over the North Atlantic Ocean, during June – July 2006. Inorganic iodine, namely iodide and iodate, was the minor iodine fraction in both campaigns, accounting for 7.3% (median) and 5.8% (median) in PM2.5 iodine at Mace Head and over the North Atlantic Ocean, respectively. Iodide concentrations were higher than iodate in most of the samples. In the contrast, more than 90% of TSI was SOI and the SOI concentration was correlated significantly with the iodide concentration. The correlation coefficients (R2) were both higher than 0.5 at Mace Head and in the first leg of the cruise. Size fractionated aerosol samples collected by 5 stage Berner impactor cascade sampler showed similar proportions of inorganic and organic iodine. Significant correlations were obtained in the particle size ranges of 0.25 – 0.71 μm and 0.71 – 2.0 μm between SOI and iodide, and better correlations were found in sunny days. TSI and iodide existed mainly in fine particle size range (< 2.0 μm) and iodate resided in coarse range (2.0 – 10 μm). Aerosol iodine was suggested to be related to the primary iodine release in the tidal zone. Natural meteorological conditions such as solar radiation, raining etc were observed to have influence on the aerosol iodine. During the ship campaign over the North Atlantic Ocean (January – February 2007), the TSI concentrations (medians) ranged 35.14 – 60.63 pmol m-3 among the 5 stages. Likewise, SOI was found to be the most abundant iodine fraction in TSI with a median of 98.6%. Significant correlation also presented between SOI and iodide in the size range of 2.0 – 5.9 μm. Higher iodate concentration was again found in the higher particle size range, similar to that at Mace Head. Airmass transport from the biogenic bloom region and the Antarctic ice front sector was observed to play an important role in aerosol iodine enhancement. The TSI concentrations observed along the 30,000 km long cruise round trip from East Asia to Antarctica during November 2005 – March 2006 were much lower than in the other campaigns, with a median of 6.51 pmol m-3. Approximately 70% of the TSI was SOI on average. The abundances of inorganic iodine including iodine and iodide were less than 30% of TSI. The median value of iodide was 1.49 pmol m-3, which was more than four fold higher than that of iodate (median, 0.28 pmol m-3). Spatial variation indicated highest aerosol iodine appearing in the tropical area. Iodine level was considerably lower in coastal Antarctica with the TSI median of 3.22 pmol m-3. However, airmass transport from the ice front sector was correlated with the enhance TSI level, suggesting the unrevealed source of iodine in the polar region. In addition, significant correlation between SOI and iodide was also shown in this campaign. A global distribution in aerosol was shown in the field campaigns in this work. SOI was verified globally ubiquitous due to the presence in the different sampling locations and its high proportion in TSI in the marine aerosols. The correlations between SOI and iodide were obtained not only in different locations but also in different seasons, implying the possible mechanism of iodide production through SOI decomposition. Nevertheless, future studies are needed for improving the current understanding of iodine chemistry in the MBL (e.g. SOI identification and quantification as well as the update modeling involving organic matters).

Corrosione atmosferica in area urbana-costiera di un acciaio Cor-Ten: studio del rilascio in ambiente dei metalli di lega

Cor-Ten is a particular kind of steel, belonging to low-alloyed steel; thanks to his aesthetic features and resistance to atmospheric corrosion, this material is largely used in architectural, artistic and infrastructural applications. After environmental exposure, Cor-Ten steel exhibits the characteristic ability to self-protect from corrosion, by the development of a stable and adherent protective layer. However, some environmental factors can influence the formation and stability of the patina. In particular, exposure of Cor-Ten to polluted atmosphere (NOx, SOx, O3) or coastal areas (marine spray) may cause problems to the protective layer and, as a consequence, a release of alloying metals, which can accumulate near the structures. Some of these metals, such as Cr and Ni, could be very dangerous for soils and water because of their large toxicity. The aim of this work was to study the corrosion behavior of Cor-Ten exposed to an urban-coastal site (Rimini, Italy). Three different kinds of commercial surface finish (bare and pre-patinated, with or without a beeswax covering) were examined, both in sheltered and unsheltered exposure conditions. Wet deposition brushing the specimens surface (leaching solutions) are monthly collected and analyzed to evaluate the extent of metal release and the form in which they leave the surface, for example, as water-soluble compounds or non-adherent corrosion products. Five alloying metals (Fe, Cu, Cr, Mn and Ni) and nine ions (Cl-, NO3-, NO2-, SO42-, Na+, Ca2+, K+, Mg2+, NH4+) are determined through Atomic Absorption Spectroscopy and Ion Chromatography, respectively. Furthermore, the evolution and the behaviour of the patina are periodically followed by surface investigations (SEM-EDS and Raman Spectroscopy). After two years of exposure, the results show that Bare Cor-Ten, cheaper than the other analyzed specimens, even though undergoes the greater mass variation, his metal release is comparable to the release of the pre-patinated samples. The behavior of pre-patinated steel, with or without beeswax covering, do not show particular difference. This exposure environment doesn’t allow a completely stabilization of the patina; nevertheless an estimate of metal release after 10 years of exposure points out that the environmental impact of Cor-Ten is very low: for example, the release of chromium in the soluble fraction is less than 10 mg if we consider an exposed wall of 10 m2.

Identifizierung biogene Amine bildender Bakterien und Einsatz von Enzymen zur Hemmung ihres Wachstums während der Weinbereitung

Mikroorganismen spielen eine wichtige Rolle in der Weinherstellung. Neben ihren positiven Stoffwechselaktivitäten wie die Bildung von Ethanol während der alkoholischen Gärung sind vor allem Bakterien in der Lage, Weinfehler zu verursachen. Einer dieser Weinfehler ist die Produktion von biogenen Aminen. Diese niedermolekularen Stickstoffverbindungen können zu verschiedenen Gesundheitsproblemen wie Bluthochdruck und Migräne führen. Aufgrund von hohen Ethanolgehalten und dem Vorkommen verschiedener biogener Amine kommt es im Wein zu einer Verstärkung dieser physiologischen Effekte. Um die Bildung dieser Verbindungen zu verhindern, ist es von speziellem Interesse, die verantwortlichen Mikroorganismen zu identifizieren und sie in ihrem Wachstum zu hemmen.In einem Teil der Dissertation stand die Isolierung und Identifizierung biogener Amine produzierender Bakterien aus deutschen Jungweinen und Mosten im Vordergrund. Es konnte gezeigt werden, dass hauptsächlich Milchsäurebakterien als potenzielle Produzenten in Frage kommen. Diese Bakteriengruppe war in hohen Titern in nahezu allen Proben vorhanden und stellt somit eine potentielle Gefahr für die Weinbereitung dar. Zur Identifizierung der Isolate wurden verschiedene molekularbiologische Methoden wie specifically amplified DNA polymorphic-PCR (Fingerprintmethode), Multiplex-PCR oder 16S rDNA-Sequenzierung angewandt. Das Screening bezüglich der Bildung von biogenen Aminen erfolgte mit Hilfe einer im Rahmen dieser Arbeit entwickelten hochauflösenden Dünnschichtchromatographie gefolgt von der Quantifizierung mittels HPLC.Zur Wachstumshemmung dieser Schadbakterien wurden zwei Exoenzyme aus Streptomyces albidoflavus B578 isolieren. Diese Enzyme wurden gereinigt und als eine Muramidase und eine Protease identifiziert. Aktivitätstests konnten zeigen, dass diese Enzyme eine hohe lytische Wirkung gegen weinrelevante Mikroorganismen aufweisen. Ebenso war die Aktivität der Enzyme unter Weinbedingungen sehr stabil. Aufgrund dieser Ergebnisse könnten diese Enzyme eine mögliche Alternative zur Zugabe von Lysozym oder Schwefeldioxid sein, welche konventionell in der Weinbereitung ihren Einsatz finden.

Complementary mass spectrometric techniques for the characterization of the organic fraction in atmospheric aerosols

Aerosol particles are strongly related to climate, air quality, visibility and human health issues. They contribute the largest uncertainty in the assessment of the Earth´s radiative budget, directly by scattering or absorbing solar radiation or indirectly by nucleating cloud droplets. The influence of aerosol particles on cloud related climatic effects essentially depends upon their number concentration, size and chemical composition. A major part of submicron aerosol consists of secondary organic aerosol (SOA) that is formed in the atmosphere by the oxidation of volatile organic compounds. SOA can comprise a highly diverse spectrum of compounds that undergo continuous chemical transformations in the atmosphere.rnThe aim of this work was to obtain insights into the complexity of ambient SOA by the application of advanced mass spectrometric techniques. Therefore, an atmospheric pressure chemical ionization ion trap mass spectrometer (APCI-IT-MS) was applied in the field, facilitating the measurement of ions of the intact molecular organic species. Furthermore, the high measurement frequency provided insights into SOA composition and chemical transformation processes on a high temporal resolution. Within different comprehensive field campaigns, online measurements of particular biogenic organic acids were achieved by combining an online aerosol concentrator with the APCI-IT-MS. A holistic picture of the ambient organic aerosol was obtained through the co-located application of other complementary MS techniques, such as aerosol mass spectrometry (AMS) or filter sampling for the analysis by liquid chromatography / ultrahigh resolution mass spectrometry (LC/UHRMS).rnIn particular, during a summertime field study at the pristine boreal forest station in Hyytiälä, Finland, the partitioning of organic acids between gas and particle phase was quantified, based on the online APCI-IT-MS and AMS measurements. It was found that low volatile compounds reside to a large extent in the gas phase. This observation can be interpreted as a consequence of large aerosol equilibration timescales, which build up due to the continuous production of low volatile compounds in the gas phase and/or a semi-solid phase state of the ambient aerosol. Furthermore, in-situ structural informations of particular compounds were achieved by using the MS/MS mode of the ion trap. The comparison to MS/MS spectra from laboratory generated SOA of specific monoterpene precursors indicated that laboratory SOA barely depicts the complexity of ambient SOA. Moreover, it was shown that the mass spectra of the laboratory SOA more closely resemble the ambient gas phase composition, indicating that the oxidation state of the ambient organic compounds in the particle phase is underestimated by the comparison to laboratory ozonolysis. These observations suggest that the micro-scale processes, such as the chemistry of aerosol aging or the gas-to-particle partitioning, need to be better understood in order to predict SOA concentrations more reliably.rnDuring a field study at the Mt. Kleiner Feldberg, Germany, a slightly different aerosol concentrator / APCI-IT-MS setup made the online analysis of new particle formation possible. During a particular nucleation event, the online mass spectra indicated that organic compounds of approximately 300 Da are main constituents of the bulk aerosol during ambient new particle formation. Co-located filter analysis by LC/UHRMS analysis supported these findings and furthermore allowed to determine the molecular formulas of the involved organic compounds. The unambiguous identification of several oxidized C 15 compounds indicated that oxidation products of sesquiterpenes can be important compounds for the initial formation and subsequent growth of atmospheric nanoparticles.rnThe LC/UHRMS analysis furthermore revealed that considerable amounts of organosulfates and nitrooxy organosulfates were detected on the filter samples. Indeed, it was found that several nitrooxy organosulfate related APCI-IT-MS mass traces were simultaneously enhanced. Concurrent particle phase ion chromatography and AMS measurements indicated a strong bias between inorganic sulfate and total sulfate concentrations, supporting the assumption that substantial amounts of sulfate was bonded to organic molecules.rnFinally, the comprehensive chemical analysis of the aerosol composition was compared to the hygroscopicity parameter kappa, which was derived from cloud condensation nuclei (CCN) measurements. Simultaneously, organic aerosol aging was observed by the evolution of a ratio between a second and a first generation biogenic oxidation product. It was found that this aging proxy positively correlates with increasing hygroscopicity. Moreover, it was observed that the bonding of sulfate to organic molecules leads to a significant reduction of kappa, compared to an internal mixture of the same mass fractions of purely inorganic sulfate and organic molecules. Concluding, it has been shown within this thesis that the application of modern mass spectrometric techniques allows for detailed insights into chemical and physico-chemical processes of atmospheric aerosols.rn

Windkanalstudien zum Graupelwachstum und Bestimmung von Retentionskoeffizienten verschiedener Spurengase während der Bereifung

Am vertikalen Windkanal der Johannes Gutenberg-Universität Mainz wurden physikalische und chemische Bereifungsexperimente durchgeführt. Dabei lagen die Umgebungstemperaturen bei allen Experimenten zwischen etwa -15 und -5°C und der Flüssigwassergehalt erstreckte sich von 0,9 bis etwa 1,6g/m³, typische Bedingungen für Mischphasenwolken in denen Bereifung stattfindet. Oberflächentemperaturmessungen an wachsenden hängenden Graupelpartikeln zeigten, dass während der Experimente trockene Wachstumsbedingungen herrschten.rnZunächst wurde das Graupelwachstum an in einer laminaren Strömung frei schwebenden Eispartikeln mit Anfangsradien zwischen 290 und 380µm, die mit flüssigen unterkühlten Wolkentröpfchen bereift wurden, studiert. Ziel war es, den Kollektionskern aus der Massenzunahme des bereiften Eispartikels und dem mittleren Flüssigwassergehalt während des Wachstumsexperimentes zu bestimmen. Die ermittelten Werte für die Kollektionskerne der bereiften Eispartikel erstreckten sich von 0,9 bis 2,3cm³/s in Abhängigkeit ihres Kollektorimpulses (Masse * Fallgeschwindigkeit des bereifenden Graupels), der zwischen 0,04 und 0,10gcm/s lag. Bei den Experimenten zeigte sich, dass die hier gemessenen Kollektionskerne höher waren im Vergleich mit Kollektionskernen flüssiger Tropfen untereinander. Aus den aktuellen Ergebnissen dieser Arbeit und der vorhandenen Literaturwerte wurde ein empirischer Faktor entwickelt, der von dem Wolkentröpfchenradius abhängig ist und diesen Unterschied beschreibt. Für die untersuchten Größenbereiche von Kollektorpartikel und flüssigen Tröpfchen können die korrigierten Kollektionskernwerte in Wolkenmodelle für die entsprechenden Größen eingebunden werden.rnBei den chemischen Experimenten zu dieser Arbeit wurde die Spurenstoffaufnahme verschiedener atmosphärischer Spurengase (HNO3, HCl, H2O2, NH3 und SO2) während der Bereifung untersucht. Diese Experimente mussten aus technischen Gründen mit hängenden Eispartikeln, dendritischen Eiskristallen und Schneeflocken, bereift mit flüssigen Wolkenlösungströpfchen, durchgeführt werden.rnDie Konzentrationen der Lösung, aus der die Wolkentröpfchen mit Hilfe von Zweistoffdüsen erzeugt wurden, lagen zwischen 1 und 120mg/l. Für die Experimente mit Ammoniak und Schwefeldioxid wurden Konzentrationen zwischen 1 und 22mg/l verwendet. Das Schmelzwasser der bereiften hängenden Graupel und Schneeflocken wurden ionenchromatographisch analysiert und zusammen mit der bekannten Konzentration der bereifenden Wolkentröpfchen konnte der Retentionskoeffizient für jeden Spurenstoff bestimmt werden. Er gibt die Menge an Spurenstoff an, die bei der Phasenumwandlung von flüssig zu fest in die Eisphase übergeht. Salpetersäure und Salzsäure waren nahezu vollständig retiniert (Mittelwerte der gesamten Experimente entsprechend 99±8% und 100±9%). Für Wasserstoffperoxid wurde ein mittlerer Retentionskoeffizient von 65±17% bestimmt. rnDer mittlere Retentionskoeffizient von Ammoniak ergab sich unabhängig vom Flüssigwassergehalt zu 92±21%, während sich für Schwefeldioxid 53±10% für niedrige und 29±7% für hohe Flüssigphasenkonzentrationen ergaben. Bei einigen der untersuchten Spurenstoffe wurde eine Temperaturabhängigkeit beobachtet und wenn möglich durch Parametrisierungen beschrieben.rn

Fruit yogurt: any erosive potential regarding teeth?

OBJECTIVE: The capability of drinks and foods to resist pH changes brought about by salivary buffering may play an important role in the dental erosion process in children. The aim of the present study was to test fruit yogurt, a popular snack for children, and the degrees of saturation (pK-pl) with respect to hydroxyapatite and fluorapatite to determine their erosive potential. METHOD AND MATERIALS: A variety of fruit yogurt was tested. To test the pH, 8 readings were taken with a pH electrode for each yogurt. Calcium content was detected by atomic absorption spectrophotometer, phosphorus by the inductively coupled plasma method, and fluoride content by ion chromatography. The degrees of saturation of hydroxyapatite and fluorapatite were calculated by use of a computer program. Statistical analysis was performed using 2-tailed analysis of variance (P < .05) and a post hoc test (Tukey) to determine differences between groups. RESULTS: The pH of each fruit concentrate was significantly different, except for banana yogurt. Except for the phosphorus content of raspberry yogurt, the calcium and phosphorus content for each fruit concentrate were significantly different. Fluoride levels were the same for all yogurts tested, and the degrees of saturation of hydroxyapatite and fluorapatite was positive, indicating supersaturation. CONCLUSION: It could be stated that fruit yogurt has no erosive potential.