A study on bending behaviours of aluminium foam-filled tubes

In the study, the strengthening effect of aluminium foam in thin-walled aluminium tubes subject to bending load in investigated experimentally and numerically. Bending tests are conducted on foam filler, hollow tube and foam-filled tube. The finite element method is used as well to get deeper insight into the crush failure modes via focusing on the influence from wall thickness of the tube. The obtained information is useful to optimally design foam-filled tubes as energy absorbing devices in automotive engineering. The optimisation results can be implemented to find an optimum foam-filled tube that absorbs the same energy as the optimal hollow tube but with much less weight. © (2014) Trans Tech Publications, Switzerland.

Analysis of backward congestion notification with delay for enhanced Ethernet networks

At present, companies and standards organizations are enhancing Ethernet as the unified switch fabric for all of the TCP/IP traffic, the storage traffic and the high performance computing traffic in data centers. Backward congestion notification (BCN) is the basic mechanism for the end-to-end congestion management enhancement of Ethernet. To fulfill the special requirements of the unified switch fabric, i.e., losslessness and low transmission delay, BCN should hold the buffer occupancy around a target point tightly. Thus, the stability of the control loop and the buffer size are critical to BCN. Currently, the impacts of delay on the performance of BCN are unidentified. When the speed of Ethernet increases to 40 Gbps or 100 Gbps in the near future, the number of on-the-fly packets becomes the same order with the buffer size of switch. Accordingly, the impacts of delay will become significant. In this paper, we analyze BCN, paying special attention on the delay. We model the BCN system with a set of segmented delayed differential equations, and then deduce sufficient condition for the uniformly asymptotic stability of BCN. Subsequently, the bounds of buffer occupancy are estimated, which provides direct guidelines on setting buffer size. Finally, numerical analysis and experiments on the NetFPGA platform verify our theoretical analysis.

Numerical modeling and analysis for forming process of dual-phase 980 steel exposed to infrared local heating

A recent experiment confirmed that the infrared (IR) local heating method drastically reduces springback of dual-phase (DP) 980 sheets. In the experiment, only the plastic deformation zone of the sheets was locally heated using condensed IR heating. The heated sheets were then deformed by V-bending or 2D-draw bending. Although the experimental observation proved the merit of using the IR local heating to reduce springback, numerical modeling has not been reported. Numerical modeling has been required to predict springback and improve the understanding of the forming process. This paper presents a numerical modeling for V-bending and 2D-draw bending of DP 980 sheets exposed to the IR local heating with the finite element method (FEM). For describing the thermo-mechanical behavior of the DP 980 sheet, a flow stress model which includes a function of temperature and effective plastic strain was newly implemented into Euler-backward stress integration method. The numerical analysis shows that the IR local heating reduces the level of stress in the deformation zone, although it heats only the limited areas, and then it reduces the springback. The simulation also provides a support that the local heating method has an advantage of shape accuracy over the method to heat the material as a whole in V-bending. The simulated results of the springback in both V-bending and 2D-draw bending also show good predictions.

Nash equilibrium under knightian uncertainty: breaking down backward induction (extensively revised version)

We define Nash equilibrium for two-person normal form games in the presence of uncertainty, in the sense of Knight(1921). We use the fonna1iution of uncertainty due to Schmeidler and Gilboa. We show tbat there exist Nash equilibria for any degree of uncertainty, as measured by the uncertainty aversion (Dow anel Wer1ang(l992a». We show by example tbat prudent behaviour (maxmin) can be obtained as an outcome even when it is not rationaliuble in the usual sense. Next, we break down backward industion in the twice repeated prisoner's dilemma. We link these results with those on cooperation in the finitely repeated prisoner's dilemma obtained by Kreps-Milgrom-Roberts-Wdson(1982), and withthe 1iterature on epistemological conditions underlying Nash equilibrium. The knowledge notion implicit in this mode1 of equilibrium does not display logical omniscience.

Nash equilibrium under knightian uncertainty: breaking-down backward induction

We present two alternative definitions of Nash equilibrium for two person games in the presence af uncertainty, in the sense of Knight. We use the formalization of uncertainty due to Schmeidler and Gilboa. We show that, with one of the definitions, prudent behaviour (maxmin) can be obtained as an outcome even when it is not rationalizable in the usual sense. Most striking is that with the Same definition we break down backward induction in the twice repeated prisoner's dilemma. We also link these results with the Kreps-Milgrom-Roberts-Wilson explanation of cooperation in the finitely repeated prisoner's dilemma.

Repair Welding Effects on the Bending Fatigue Strength of AISI 4130 Aeronautical Steel used in a Critical to the Flight-Safety Structure

The aim of this study was to analyze the effect of successive TIG (tungsten inert gas) welding repairs on the reverse bending fatigue strength of AISI 4130 steel, which is widely used in components critical to the flight-safety. In order to simulate the abrupt maneuvers, wind bursts, motor vibration and helixes efforts, which generate cyclic bending loadings at the welded joints of a specific aircraft component called motor cradle, experimental reverse bending fatigue tests were carried out on specimens made from hot-rolled steel plate, 1.10 mm (0.043 in) thick, by mean of a SCHENK PWS equipment, with load ratio R = -1, under constant amplitude, at 30 Hz frequency and room temperature. It was observed that the bending fatigue strength decreases after the TIG (Tungsten Inert Gas) welding process application on AISI 4130 steel, with subsequent decrease due to re-welding sequence as well. Microstructural analyses and microhardness measurements on the base material, heat-affected zone (HAZ) and weld metal, as well as the effects of the weld bead geometry on the obtained results, have complemented this study.

BEM Formulations Based on Kirchhoff's Hypoyhesis to Perform Linear Bending Analysis of Plates Reinforced by Beams

In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoffs hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a stab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. on these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degrees of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.

Analysis of the Coupled Stretching-Bending Problem of Stiffened Plates by a BEM Formulation Based on Reissner's Hypothesis

In this work, the plate bending formulation of the boundary element method - BEM, based on the Reissner's hypothesis, is extended to the analysis of plates reinforced by beams taking into account the membrane effects. The formulation is derived by assuming a zoned body where each sub-region defines a beam or a slab and all of them are represented by a chosen reference surface. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to reduce the number of degrees of freedom, the problem values defined on the interfaces are written in terms of their values on the beam axis. Initially are derived separated equations for the bending and stretching problems, but in the final system of equations the two problems are coupled and can not be treated separately. Finally are presented some numerical examples whose analytical results are known to show the accuracy of the proposed model.

A BEM formulation for analysing the coupled stretching-bending problem of plates reinforced by rectangular beams with columns defined in the domain

In this work, a boundary element formulation to analyse plates reinforced by rectangular beams, with columns defined in the domain is proposed. The model is based on Kirchhoff hypothesis and the beams are not required to be displayed over the plate surface, therefore eccentricity effects are taken into account. The presented boundary element method formulation is derived by applying the reciprocity theorem to zoned plates, where beams are treated as thin sub-regions with larger rigidities. The integral representations derived for this complex structural element consider the bending and stretching effects of both structural elements working together. The standard equilibrium and compatibility conditions along interface are naturally imposed, being the bending tractions eliminated along interfaces. The in-plane tractions and the bending and in-plane displacements are approximated along the beam width, reducing the number of degrees of freedom. The columns are introduced into the formulation by considering domain points where tractions can be prescribed. Some examples are then shown to illustrate the accuracy of the formulation, comparing the obtained results with other numerical solutions.

Fast-forward/fast-backward substitutions on vector computers

This paper deals with approaches for sparse matrix substitutions using vector processing. Many publications have used the W-matrix method to solve the forward/backward substitutions on vector computer. Recently a different approach has been presented using dependency-based substitution algorithm (DBSA). In this paper the focus is on new algorithms able to explore the sparsity of the vectors. The efficiency is tested using linear systems from power systems with 118, 320, 725 and 1729 buses. The tests were performed on a CRAY Y MP2E/232. The speedups for a fast-forward/fast-backward using a 1729-bus system are near 19 and 14 for real and complex arithmetic operations, respectively. When forward/backward is employed the speedups are about 8 and 6 to perform the same simulations.

Bending of light in the framework of R + R2 gravity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Measurement of the forward-backward charge asymmetry in top-quark pair production

We present the first measurement of the integrated forward-backward charge asymmetry in top-quark-top-antiquark pair (t (t) over bar) production in proton-antiproton (p (p) over bar) collisions in the lepton+jets final state. Using a b-jet tagging algorithm and kinematic reconstruction assuming t (t) over bar +X production and decay, a sample of 0.9 fb(-1) of data, collected by the D0 experiment at the Fermilab Tevatron Collider, is used to measure the asymmetry for different jet multiplicities. The result is also used to set upper limits on t (t) over bar +X production via a Z' resonance.

Measurement of the Forward-Backward Charge Asymmetry and Extraction of sin(2)theta(eff)(W) in pp -> Z/gamma(*)+X -> e(+)e(-)+X Events Produced at s=1.96 TeV

We present a measurement of the forward-backward charge asymmetry (A(FB)) in pp -> Z/gamma(*)+X -> e(+)e(-)+X events at a center-of-mass energy of 1.96 TeV using 1.1 fb(-1) of data collected with the D0 detector at the Fermilab Tevatron collider. A(FB) is measured as a function of the invariant mass of the electron-positron pair, and found to be consistent with the standard model prediction. We use the A(FB) measurement to extract the effective weak mixing angle sin(2)theta(eff)(W)=0.2326 +/- 0.0018(stat)+/- 0.0006(syst).