Energetic efficiency of an agricultural tractor in function of tire inflation pressure

The tire inflation pressure, among other factors, determines the efficiency in which a tractor can exert traction. It was studied the effect of using two tire inflation pressures, 110.4 kPa in the front and rear wheels, 124.2 kPa in the front wheel and 138 kPa in the rear wheels, the energetic efficiency of an agricultural tractor of 147 kW of engine power, in the displacement speed of 6.0 km.h-1, on track with firm surface, with the tractor engine speed of 2000 rpm. For each condition of the tire pressure, the tested tractor was subjected to constant forces in the drawbar of 45 kN and 50 kN, covering 30 meters. It was used a randomized complete block with a 2x2 factorial arrangement (tire pressure and drawbar power) with four replications, totaling 16 experimental units. Data were subjected to analysis of variance, using the Tukey test at 5% probability for comparison averages. The lowest hourly and specific fuel consumption, the lowest slippage of the wheelsets and the highest efficiency in the drawbar was obtained with the tire inflation pressure of 110.4 kPa in the front and rear tires of the tractor, highlighting that lower pressures improve energetic and operational performance of the tractor.

Potential of adjuvants to reduce drift in agricultural spraying

The reduction of pesticide spraying drift is still one of the major challenges in Brazilian agriculture. The aim of this study was to evaluate the potential of different adjuvant products, such as surfactants, drift retardants, mineral oil and vegetable oil for reducing drift in agricultural spraying. The experiment consisted of quantifying drift of sprayings of 18 adjuvants dissolved in water under controlled conditions in a wind tunnel. Tests were performed in triplicates with spraying nozzles type Teejet XR8003 VK, pressure of 200kPa and medium drops. Solutions sprayed were marked with Brilliant Blue dye at 0.6% (m v-1). The drift was collected using polyethylene strips transversally fixed along the tunnel at different distances from the nozzle and different heights from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry in order to quantify deposits. The adjuvants from chemical groups of mineral oil and drift retardant resulted in lower values of drift in comparison with surfactants and water. The results obtained in laboratory show that the selection of appropriate class and concentration of adjuvants can significantly decrease the risk of drift in agricultural spraying. However, the best results obtained in laboratory should be validated with pesticide under field conditions in the future.

Dry months in the agricultural region of Ribeirão Preto, state of São Paulo-Brazil: an study based on the extreme value theory

The application of the Extreme Value Theory (EVT) to model the probability of occurrence of extreme low Standardized Precipitation Index (SPI) values leads to an increase of the knowledge related to the occurrence of extreme dry months. This sort of analysis can be carried out by means of two approaches: the block maxima (BM; associated with the General Extreme Value distribution) and the peaks-over-threshold (POT; associated with the Generalized Pareto distribution). Each of these procedures has its own advantages and drawbacks. Thus, the main goal of this study is to compare the performance of BM and POT in characterizing the probability of occurrence of extreme dry SPI values obtained from the weather station of Ribeirão Preto-SP (1937-2012). According to the goodness-of-fit tests, both BM and POT can be used to assess the probability of occurrence of the aforementioned extreme dry SPI monthly values. However, the scalar measures of accuracy and the return level plots indicate that POT provides the best fit distribution. The study also indicated that the uncertainties in the parameters estimates of a probabilistic model should be taken into account when the probability associated with a severe/extreme dry event is under analysis.

Spray adjuvant characteristics affecting agricultural spraying drift

This study defined the main adjuvant characteristics that may influence or help to understand drift formation process in the agricultural spraying. It was evaluated 33 aqueous solutions from combinations of various adjuvants and concentrations. Then, drifting was quantified by means of wind tunnel; and variables such as percentage of droplets smaller than 50 μm (V50), 100 μm (V100), diameter of mean volume (DMV), droplet diameter composing 10% of the sprayed volume (DV0.1), viscosity, density and surface tension. Assays were performed in triplicate, using Teejet XR8003 flat fan nozzles at 200 kPa (medium size droplets). Spray solutions were stained with Brilliant Blue Dye at 0.6% (m/ v). DMV, V100, viscosity cause most influence on drift hazardous. Adjuvant characteristics and respective methods of evaluation have applicability in drift risk by agricultural spray adjuvants.

AGRICULTURAL MACHINERY AND IMPLEMENTS DESIGN PROCESS: GUIDELINES FOR SMALL AND MID-SIZED BUSINESSES

ABSTRACT This study aims at presenting the process of machine design and agricultural implements by means of a reference model, formulated with the purpose of explaining the development activities of new products, serving as a guideline to coach human resources and to assist in formalizing the process in small and medium-sized businesses (SMB), i.e. up to 500 employees. The methodology used included the process modeling, carried out from case studies in the SMB, and the study of reference models in literature. The modeling formalism used was based on the IDEF0 standard, which identifies the dimensions required for the model detailing: input information; activities; tasks; knowledge domains; mechanisms; controls and information produced. These dimensions were organized in spreadsheets and graphs. As a result, a reference model with 27 activities and 71 tasks was obtained, distributed over four phases of the design process. The evaluation of the model was carried out by the companies participating in the case studies and by experts, who concluded that the model explains the actions needed to develop new products in SMB.

Internal quality control indicators of cervical cytopathology exams performed in laboratories monitored by the External Quality Control Laboratory

PURPOSE: To evaluate the impact of continued education provided by an external quality control laboratory on the indicators of internal quality control of cytopathology exams.METHODS: The internal quality assurance indicators for cytopathology exams from 12 laboratories monitored by the External Quality Control Laboratory were evaluated. Overall, 185,194 exams were included, 98,133 of which referred to the period preceding implementation of a continued education program, while 87,061 referred to the period following this intervention. Data were obtained from the Cervical Cancer Database of the Brazilian National Health Service.RESULTS: Following implementation of the continued education program, the positivity index (PI) remained within recommended limits in four laboratories. In another four laboratories, the PI progressed from below the limits to within the recommended standards. In one laboratory, the PI remained low, in two laboratories, it remained very low, and in one, it increased from very low to low. The percentage of exams compatible with a high-grade squamous intraepithelial lesion (HSIL) remained within the recommended limits in five laboratories, while in three laboratories it progressed from below the recommended levels to >0.4% of the total number of satisfactory exams, and in four laboratories it remained below the standard limit. Both the percentage of atypical squamous cells of undetermined significance (ASC-US) in relation to abnormal exams, and the ratio between ASC-US and intraepithelial lesions remained within recommended levels in all the laboratories investigated.CONCLUSION: An improvement was found in the indicators represented by the positivity index and the percentage of exams compatible with a high-grade squamous intraepithelial lesion, showing that the role played by the external quality control laboratory in providing continued education contributed towards improving laboratory staff skills in detecting cervical cancer precursor lesions.

GIS assessing traditional and modern agricultural land use/land cover change. A case study 1959-2005: Rekijoki, Somero, SW-Finland

Finland’s rural landscape has gone through remarkable changes from the 1950’s, due to agricultural developments. Changed farming practices have influenced especially traditional landscape management, and modifications in the arable land structure and grasslands transitions are notable. The review of the previous studies reveal the importance of the rural landscape composition and structure to species and landscape diversity, whereas including the relevance in presence of the open ditches, size of the field and meadow patches, topology of the natural and agricultural landscape. This land-change study includes applying remote sensed data from two time series and empirical geospatial analysis in Geographic Information Systems (GIS). The aims of this retrospective research is to detect agricultural landscape use and land cover change (LULCC) dynamics and discuss the consequences of agricultural intensification to landscape structure covering from the aspects of landscape ecology. Measurements of LULC are derived directly from pre-processed aerial images by a variety of analytical procedures, including statistical methods and image interpretation. The methodological challenges are confronted in the process of landscape classification and combining change detection approaches with landscape indices. Particular importance is paid on detecting agricultural landscape features at a small scale, demanding comprehensive understanding of such agroecosystems. Topological properties of the classified arable land and valley are determined in order to provide insight and emphasize the aspect the field edges in the agricultural landscape as important habitat. Change detection dynamics are presented with change matrix and additional calculations of gain, loss, swap, net change, change rate and tendencies are made. Transition’s possibility is computed following Markov’s probability model and presented with matrix, as well. Thesis’s spatial aspect is revealed with illustrative maps providing knowledge of location of the classified landscape categories and location of the dynamics of the changes occurred. It was assured that in Rekijoki valley’s landscape, remarkable changes in landscape has occurred. Landscape diversity has been strongly influenced by modern agricultural landscape change, as NP of open ditches has decreased and the MPS of the arable plot has decreased. Overall change in the diversity of the landscape is determined with the decrease of SHDI. Valley landscape considered as traditional land use area has experienced major transitional changes, as meadows class has lost almost one third of the area due to afforestation. Also, remarkable transitions have occurred from forest to meadow and arable land to built area. Boundaries measurement between modern and traditional landscape has indicated noticeable proportional increase in arable land-forest edge type and decrease in arable land-meadow edge type. Probability calculations predict higher future changes for traditional landscape, but also for arable land turning into built area.

Effect of long-term agricultural management systems on occurrence and composition of weed species

This study aims to assess the composition of weed communities as a function of distinct selection factors, at neighboring areas submitted to distinct soil management and diverse use for sixteen years. Four areas submitted to distinct managements (conventional tillage system; no-till system; integration crop/livestock and continuous livestock) were sampled in relation to the occurrence and severity of weed species by the beginning of the planting season, being estimated the relative abundance, relative frequency and relative dominance of each weed species under each area, as well as the Importance Value Index for each species. Areas were also compared by the Sørensen's similarity coefficient. Areas where pasture and grazing were never present, exhibited a number of seedlings of weed species 250% higher than areas periodically or continuously under grazing, while the area of soil covered by weeds was 87% superior at the conventional tillage system in relation to the average of the other treatments. Grass weeds were the most important at the conventional tillage area while broadleaved weeds where more important at the no-till area, probably due also to herbicide selection factors. Under crop/livestock integration there may be the need to care about controlling seedlings of the forage species inside grain crops in succession.

Phytosociology in agricultural areas submitted to distinct wintercropping management

Studies related to weed dynamics are essential for agricultural sustainability in tropical soils, as their interference can cause significant yield losses, especially in crops with lower competitive ability. This study aimed to assess the composition of weed communities in the third cropping season in areas submitted to distinct wintercroppings for two consecutive years. Evaluations were made in terms of species composition, level of infestation, and severity of occurrence of each weed species in relation to the others within the same area. The wintercropping management systems were: (1) Brachiaria ruziziensis; (2) corn intercropped with B. ruziziensis; (3) corn and (4) cowpea. Plant communities under these wintercrop systems were evaluated in the third year in terms of relative frequency, relative dominance, relative abundance and importance index for each species. Areas were also compared in terms of species composition by the Sorensen's similarity coefficient. Two years of distinct wintercrop managements were not enough to cause a significant shift in terms of weed composition and severity in a given area. There is also evidence that some weed species are more favored by specific crops, although the causes of this selective behavior are not fully explored in this article. The presence of B. ruziziensis, either alone or intercropped with corn, resulted in lower similarity coefficients when compared to areas where this species was not present. It is suggested that several mechanisms briefly discussed may be involved in the impact of the presence of B. ruziziensis on the weed community.

DETECTION OF GLYPHOSATE-RESISTANT PALMER AMARANTH (Amaranthus palmeri) IN AGRICULTURAL AREAS OF MATO GROSSO, BRAZIL

ABSTRACT The recent introduction of Palmer amaranth (Amaranthus palmeri) in Brazilian agricultural areas may promote several changes on weed management, especially in no-till systems and in glyphosate-resistant crops, since glyphosate-resistant biotypes of A. palmerihave been frequently selected in other countries. Therefore, this research was developed in order to evaluate the glyphosate susceptibility of a Palmer amaranth biotype recently identified in the State of Mato Grosso, Brazil. For this purpose, glyphosate susceptibility of three Amaranthusbiotypes was compared: A.hybridus var. patulus, collected in the State of Rio Grande do Sul - Brazil; A.hybridus var. patulus, collected in the State of São Paulo - Brazil; and A.palmeri, collected in the State of Mato Grosso - Brazil. Dose-response curves were generated for all biotypes, considering eight rates of glyphosate and six replicates. All the experiments were repeated twice. Both A.hybridus biotypes were satisfactorily controlled by glyphosate, demanding rates equal to or lower than 541.15 g a.e. ha-1 for 80% control (LD80). The A.palmeri biotype was not controlled by glyphosate in any of the assessments and required rates greater than 4,500 g a.e. ha-1 to reach LD80, which are economically and environmentally unacceptable. Comparison of the Brazilian A.palmeri biotype to the A. hybridus biotypes, as well as, to the results available in scientific international literature, led to the conclusion that the Brazilian Palmer amaranth biotype is resistant to glyphosate.

Weed Phytosociological and Floristic Survey in Agricultural Areas of Southwestern Goiás Region

The use of the Roundup Ready(r) technology and the cultivation of a second crop influence the floristic composition of weed communities in Brazilian Central-West region cropping systems. This study has aimed to diagnose the dominant weed species in southwestern Goiás in areas of genetically-modified and conventional soybeans, using phytosociological and floristic surveys. Weed sampling was obtained by collecting all the plants present within a 0.5 m hollow frame, randomly thrown 20 times in each of thirty-five agricultural areas in the 2012/2013 harvest. Field survey was carried out in three periods: before desiccation for soybean sowing, before postemergence herbicide in soybean first application and before postemergence herbicide application in late harvest. A total of 525 m2 was inventoried and 3,219 weeds were collected, which included 79 species, 58 genera and 28 families. Families Poaceae, Asteraceae, Euphorbiaceae, Fabaceae, Amaranthaceae, were the most representative in the survey. Species Cenchrus echinatus, Glycine max, Chamaesyce hirta, Commelina benghalensis, and Alternanthera tenella stood out in importance. The RR+millet soybean treatment had the highest number of species (44), while the conventional soybean + sorghum treatment had the lowest number of species (18). The highest number of species was recorded in first sampling period. Treatments conventional soybean + maize and conventional soybean + millet showed higher similarity (70%), while treatments RR soybean + millet and conventional soybean + sorghum showed the least (51%). Species of difficult control were recorded in all cultivation systems analyzed.

Energy and Dynamics of the solar agricultural robot "SolarSprayer"

The main objective of the present study was to design an agricultural robot, which work is based on the generation of the electricity by the solar panel. To achieve the proper operation of the robot according to the assumed working cycle the detailed design of the main equipment was made. By analysing the possible areas of implementation together with developments, the economic forecast was held. As a result a decision about possibility of such device working in agricultural sector was made and the probable topics of the further study were found out.

The GATO gene annotation tool for research laboratories

Large-scale genome projects have generated a rapidly increasing number of DNA sequences. Therefore, development of computational methods to rapidly analyze these sequences is essential for progress in genomic research. Here we present an automatic annotation system for preliminary analysis of DNA sequences. The gene annotation tool (GATO) is a Bioinformatics pipeline designed to facilitate routine functional annotation and easy access to annotated genes. It was designed in view of the frequent need of genomic researchers to access data pertaining to a common set of genes. In the GATO system, annotation is generated by querying some of the Web-accessible resources and the information is stored in a local database, which keeps a record of all previous annotation results. GATO may be accessed from everywhere through the internet or may be run locally if a large number of sequences are going to be annotated. It is implemented in PHP and Perl and may be run on any suitable Web server. Usually, installation and application of annotation systems require experience and are time consuming, but GATO is simple and practical, allowing anyone with basic skills in informatics to access it without any special training. GATO can be downloaded at [http://mariwork.iq.usp.br/gato/]. Minimum computer free space required is 2 MB.

Genetically Modified Organisms (GMOs) and Agroecology in Agricultural Production in the United States - A Comparative Analysis.

The world’s population is growing at a rapid rate and one of the primary problems of a growing is food supply. To ensure food supply and security, the biggest companies in the agricultural sector of the United States and all over the world have collaborated to produce genetically modified organisms, including crops, that have a tendency to increase yields and are speculated to reduce pesticide use. It’s a technology that is declared to have a multitude of benefits. During the same time period another set of practices has risen to the horizon by the name of agroecology. It spreads across many different sectors such as politics, sociology, environment, health and so on. Moreover, it involves primitive organic techniques that can be applied at farm level to enhance the performance of an ecosystem to effectively decrease the negative effect on environment and health of individuals while producing good quality foods. Since both the processes proclaim sustainable development, a natural question may come in mind that which one seems more favorable? During the course of this study, genetically modified organisms (GMOs) and agroecology are compared within the sphere of social, environmental and health aspects. The results derived upon a comparative analysis of scientific literature tend to prove that GMOs pose a greater threat to the environment, health of individuals and the generalized social balance in the United States compared to agroecological practices. Economic indicators were not included in the study and more studies might be needed in the future to get a broader view on the subject.