Holistic Design In High-Speed Optical Interconnects

Integrated circuit scaling has enabled a huge growth in processing capability, which necessitates a corresponding increase in inter-chip communication bandwidth. As bandwidth requirements for chip-to-chip interconnection scale, deficiencies of electrical channels become more apparent. Optical links present a viable alternative due to their low frequency-dependent loss and higher bandwidth density in the form of wavelength division multiplexing. As integrated photonics and bonding technologies are maturing, commercialization of hybrid-integrated optical links are becoming a reality. Increasing silicon integration leads to better performance in optical links but necessitates a corresponding co-design strategy in both electronics and photonics. In this light, holistic design of high-speed optical links with an in-depth understanding of photonics and state-of-the-art electronics brings their performance to unprecedented levels. This thesis presents developments in high-speed optical links by co-designing and co-integrating the primary elements of an optical link: receiver, transmitter, and clocking.

In the first part of this thesis a 3D-integrated CMOS/Silicon-photonic receiver will be presented. The electronic chip features a novel design that employs a low-bandwidth TIA front-end, double-sampling and equalization through dynamic offset modulation. Measured results show -14.9dBm of sensitivity and energy efficiency of 170fJ/b at 25Gb/s. The same receiver front-end is also used to implement source-synchronous 4-channel WDM-based parallel optical receiver. Quadrature ILO-based clocking is employed for synchronization and a novel frequency-tracking method that exploits the dynamics of IL in a quadrature ring oscillator to increase the effective locking range. An adaptive body-biasing circuit is designed to maintain the per-bit-energy consumption constant across wide data-rates. The prototype measurements indicate a record-low power consumption of 153fJ/b at 32Gb/s. The receiver sensitivity is measured to be -8.8dBm at 32Gb/s.

Next, on the optical transmitter side, three new techniques will be presented. First one is a differential ring modulator that breaks the optical bandwidth/quality factor trade-off known to limit the speed of high-Q ring modulators. This structure maintains a constant energy in the ring to avoid pattern-dependent power droop. As a first proof of concept, a prototype has been fabricated and measured up to 10Gb/s. The second technique is thermal stabilization of micro-ring resonator modulators through direct measurement of temperature using a monolithic PTAT temperature sensor. The measured temperature is used in a feedback loop to adjust the thermal tuner of the ring. A prototype is fabricated and a closed-loop feedback system is demonstrated to operate at 20Gb/s in the presence of temperature fluctuations. The third technique is a switched-capacitor based pre-emphasis technique designed to extend the inherently low bandwidth of carrier injection micro-ring modulators. A measured prototype of the optical transmitter achieves energy efficiency of 342fJ/bit at 10Gb/s and the wavelength stabilization circuit based on the monolithic PTAT sensor consumes 0.29mW.

Lastly, a first-order frequency synthesizer that is suitable for high-speed on-chip clock generation will be discussed. The proposed design features an architecture combining an LC quadrature VCO, two sample-and-holds, a PI, digital coarse-tuning, and rotational frequency detection for fine-tuning. In addition to an electrical reference clock, as an extra feature, the prototype chip is capable of receiving a low jitter optical reference clock generated by a high-repetition-rate mode-locked laser. The output clock at 8GHz has an integrated RMS jitter of 490fs, peak-to-peak periodic jitter of 2.06ps, and total RMS jitter of 680fs. The reference spurs are measured to be –64.3dB below the carrier frequency. At 8GHz the system consumes 2.49mW from a 1V supply.

Investigation into the Influence of Build Parameters on Failure of 3D Printed Parts

Additive manufacturing, including fused deposition modeling (FDM), is transforming the built world and engineering education. Deep understanding of parts created through FDM technology has lagged behind its adoption in home, work, and academic environments. Properties of parts created from bulk materials through traditional manufacturing are understood well enough to accurately predict their behavior through analytical models. Unfortunately, Additive Manufacturing (AM) process parameters create anisotropy on a scale that fundamentally affects the part properties. Understanding AM process parameters (implemented by program algorithms called slicers) is necessary to predict part behavior. Investigating algorithms controlling print parameters (slicers) revealed stark differences between the generation of part layers. In this work, tensile testing experiments, including a full factorial design, determined that three key factors, width, thickness, infill density, and their interactions, significantly affect the tensile properties of 3D printed test samples.

Algoritmos de reconstrucción de superficies 3D para modelaje antropométrico

Los protocolos de medición antropométrica se caracterizan por la profusión de medidas discretas o localizadas, en un intento para caracterizar completamente la forma corporal del sujeto -- Dichos protocolos se utilizan intensivamente en campos como medicina deportiva, forense y/o reconstructiva, diseño de prótesis, ergonomía, en la confección de prendas, accesorios, etc -- Con el avance de algoritmos de recuperación de formas a partir de muestreos (digitalizaciones) la caracterización antropométrica se ha alterado significativamente -- El articulo presente muestra el proceso de caracterización digital de forma corpórea, incluyendo los protocolos de medición sobre el sujeto, el ambiente computacional - DigitLAB- (desarrollado en el CII-CAD-CAM-CG de la Universidad EAFIT) para recuperación de superficies, hasta los modelos geométricos finales -- Se presentan comparaciones de los resultados obtenidos con DigitLAB y con paquetes comerciales de recuperación de forma 3D -- Los resultados de DigitLAB resultan superiores, debido principalmente al hecho de que este toma ventaja de los patrones de las digitalizaciones (planares de contacto, por rejilla de pixels - range images -, etc.) y provee módulos de tratamiento geométrico - estadístico de los datos para poder aplicar efectivamente los algoritmos de recuperación de forma -- Se presenta un caso de estudio dirigido a la industria de la confección, y otros efectuados sobre conjuntos de prueba comunes en el ámbito científico para la homologación de algoritmos

Through Wafer 3D Vertical Micro-Coaxial Probe for High Frequency Material Characterization and Millimeter Wave Packaging Systems

This work presents the development of an in-plane vertical micro-coaxial probe using bulk micromachining technique for high frequency material characterization. The coaxial probe was fabricated in a silicon substrate by standard photolithography and a deep reactive ion etching (DRIE) technique. The through-hole structure in the form of a coaxial probe was etched and metalized with a diluted silver paste. A co-planar waveguide configuration was integrated with the design to characterize the probe. The electrical and RF characteristics of the coaxial probe were determined by simulating the probe design in Ansoft’s High Frequency Structure Simulator (HFSS). The reflection coefficient and transducer gain performance of the probe was measured up to 65 GHz using a vector network analyzer (VNA). The probe demonstrated excellent results over a wide frequency band, indicating its ability to integrate with millimeter wave packaging systems as well as characterize unknown materials at high frequencies. The probe was then placed in contact with 3 materials where their unknown permittivities were determined. To accomplish this, the coaxial probe was placed in contact with the material under test and electromagnetic waves were directed to the surface using the VNA, where its reflection coefficient was then determined over a wide frequency band from dc-to -65GHz. Next, the permittivity of each material was deduced from its measured reflection coefficients using a cross ratio invariance coding technique. The permittivity results obtained when measuring the reflection coefficient data were compared to simulated permittivity results and agreed well. These results validate the use of the micro-coaxial probe to characterize the permittivity of unknown materials at high frequencies up to 65GHz.

Development and validation of a computationally efficient pseudo 3D model for planar SOFC integrated with a heating furnace

Efficient numerical models facilitate the study and design of solid oxide fuel cells (SOFCs), stacks, and systems. Whilst the accuracy and reliability of the computed results are usually sought by researchers, the corresponding modelling complexities could result in practical difficulties regarding the implementation flexibility and computational costs. The main objective of this article is to adapt a simple but viable numerical tool for evaluation of our experimental rig. Accordingly, a model for a multi-layer SOFC surrounded by a constant temperature furnace is presented, trained and validated against experimental data. The model consists of a four-layer structure including stand, two interconnects, and PEN (Positive electrode-Electrolyte-Negative electrode); each being approximated by a lumped parameter model. The heating process through the surrounding chamber is also considered. We used a set of V-I characteristics data for parameter adjustment followed by model verification against two independent sets of data. The model results show a good agreement with practical data, offering a significant improvement compared to reduced models in which the impact of external heat loss is neglected. Furthermore, thermal analysis for adiabatic and non-adiabatic process is carried out to capture the thermal behaviour of a single cell followed by a polarisation loss assessment. Finally, model-based design of experiment is demonstrated for a case study.

Design of a Novel Auto-Rotating UAV Platform for Underground Mine Cavity Surveying

The purpose of this paper is to investigate the potential for use of UAVs in underground mines and present a prototype design for a novel autorotating UAV platform for underground 3D data collection.

Melhoria da Carga Psicológica de um Auxiliar de Marcha para Crianças com Mobilidade Reduzida através do Design Emocional

A presente dissertação retrata o desenvolvimento de um auxiliar de marcha para crianças com mobilidade reduzida, mais propriamente um andarilho. Foi escolhido este tema devido à carga negativa que é associada a todos os produtos de apoio existentes no mercado. Esta proposta pretende fazer uma inclusão da criança com o meio que a rodeia, permitir uma maior interação com as outras crianças e até certo ponto fazê-las esquecer que o andarilho é um produto obrigatório e apenas com fins terapêuticos, mas sim uma extensão do corpo que lhe vai permitir brincar e explorar o mundo que a rodeia de uma forma mais divertida. Os andarilhos existentes atualmente continuam com o aspeto frio e hospitalar que sempre tiveram, e é necessário ter consciência que os utilizadores são crianças e como todas as crianças identificam-se com formas orgânicas e cores apelativas. A modelação 3d assim como os desenhos técnicos do andarilho foram desenvolvidos com recurso aos softwares Solid Works e Autocad. O produto desenvolvido atingiu o objetivo inicial proposto. É um andarilho em alumínio revestido a ABS, obtendo assim formas mais orgânicas, fazendo esquecer que se trata de um produto necessário e terapêutico e lembrando um brinquedo, o que o faz corresponder às expectativas propostas.

Improving magnetic coupling for battery charging through 3D magnetic flux

The spatial distribution of the magnetic field and the coupling between the coils in the Wireless Power Transfer (WPT) systems is an important aspect to consider in the system design and efficiency optimization. The presented study in this paper is based on tests performed on a physical model. The transmitting (primary) equipment, is an electrical three-phase system, capable to be connected in star or delta (both electrically and geometrically). The measured results allow to describe graphically the magnetic field distribution in three dimensions. The analytical formulas aim to help to understand and to quantify the physical phenomena but they cannot be considered a universal approach and the measurement results help to understand better the observable facts. In the WPT, the key issues that will influence the efficiency, are the alignment of the coils, the spatial orientation of the magnetic field, the detachment and the tilt between the windings, all they changing the magnetic coupling between the transmitter and the receiver of energy. This research is directed not only to the magnetic field distribution but finally, to optimize the energy transfer efficiency.

Numerical and experimental analysis of 3D printed smart structures and systems

Three dimensional (3D) printers of continuous fiber reinforced composites, such as MarkTwo (MT) by Markforged, can be used to manufacture such structures. To date, research works devoted to the study and application of flexible elements and CMs realized with MT printer are only a few and very recent. A good numerical and/or analytical tool for the mechanical behavior analysis of the new composites is still missing. In addition, there is still a gap in obtaining the material properties used (e.g. elastic modulus) as it is usually unknown and sensitive to printing parameters used (e.g. infill density), making the numerical simulation inaccurate. Consequently, the aim of this thesis is to present several work developed. The first is a preliminary investigation on the tensile and flexural response of Straight Beam Flexures (SBF) realized with MT printer and featuring different interlayer fiber volume-fraction and orientation, as well as different laminate position within the sample. The second is to develop a numerical analysis within the Carrera' s Unified Formulation (CUF) framework, based on component-wise (CW) approach, including a novel preprocessing tool that has been developed to account all regions printed in an easy and time efficient way. Among its benefits, the CUF-CW approach enables building an accurate database for collecting first natural frequencies modes results, then predicting Young' s modulus based on an inverse problem formulation. To validate the tool, the numerical results are compared to the experimental natural frequencies evaluated using a digital image correlation method. Further, we take the CUF-CW model and use static condensation to analyze smart structures which can be decomposed into a large number of similar components. Third, the potentiality of MT in combination with topology optimization and compliant joints design (CJD) is investigated for the realization of automated machinery mechanisms subjected to inertial loads.

Design and evaluation of aerosol and liquid separation systems

Conventional chromatographic columns are packed with porous beads by the universally employed slurry-packing method. The lack of precise control of the particle size distribution, shape and position inside the column have dramatic effects on the separation efficiency. In the first part the thesis an ordered, three-dimensional, pillar-array structure was designed by a CAD software. Several columns, characterized by different fluid distributors and bed length, were produced by a stereolithographic 3D printer and compared in terms of pressure drop and height equivalent to a theroretical plate (HETP). To prevent the release of unwanted substances and to provide a surface for immobilizing a ligand, pillars were coated with one or more of the following materials: titanium dioxide, nanofibrillated cellulose (NFC) and polystyrene. The external NFC layer was functionalized with Cibacron Blue and the dynamic binding capacity of the column was measured by performing three chromatographic cycles, using bovine serum albumin (BSA) as target molecule. The second part of the thesis deals with Covid-19 pandemic related research activities. In early 2020, due to the pandemic outbreak, surgical face masks became an essential non-pharmaceutical intervention to limit the spread. To address the consequent shortage and to support the reconversion of the Italian industry, in late March 2020 a multidisciplinary group of the University of Bologna created the first Italian laboratory able to perform all the tests required for the evaluation and certification of surgical masks. More than 1200 tests were performed on about 350 prototypes, according to the standard EN 14683:2019. The results were analyzed to define the best material properties and masks composition for the production of masks with excellent efficiency. To optimize the usage of surgical masks and to reduce their environmental burden, the variation of their performance over time of usage were investigated as to determine the maximum lifetime.

Development of numerical tools for the simulation, design and optimization of a Helicon Plasma Thruster

This work thesis focuses on the Helicon Plasma Thruster (HPT) as a candidate for generating thrust for small satellites and CubeSats. Two main topics are addressed: the development of a Global Model (GM) and a 3D self-consistent numerical tool. The GM is suitable for preliminary analysis of HPTs with noble gases such as argon, neon, krypton, and xenon, and alternative propellants such as air and iodine. A lumping methodology is developed to reduce the computational cost when modelling the excited species in the plasma chemistry. A 3D self-consistent numerical tool is also developed that can treat discharges with a generic 3D geometry and model the actual plasma-antenna coupling. The tool consists of two main modules, an EM module and a FLUID module, which run iteratively until a steady state solution is converged. A third module is available for solving the plume with a simplified semi-analytical approach, a PIC code, or directly by integration of the fluid equations. Results obtained from both the numerical tools are benchmarked against experimental measures of HPTs or Helicon reactors, obtaining very good qualitative agreement with the experimental trend for what concerns the GM, and an excellent agreement of the physical trends predicted against the measured data for the 3D numerical strategy.

Design and characterization of automated agricultural vehicle systems

Nowadays, technological advancements have brought industry and research towards the automation of various processes. Automation brings a reduction in costs and an improvement in product quality. For this reason, companies are pushing research to investigate new technologies. The agriculture industry has always looked towards automating various processes, from product processing to storage. In the last years, the automation of harvest and cultivation phases also has become attractive, pushed by the advancement of autonomous driving. Nevertheless, ADAS systems are not enough. Merging different technologies will be the solution to obtain total automation of agriculture processes. For example, sensors that estimate products' physical and chemical properties can be used to evaluate the maturation level of fruit. Therefore, the fusion of these technologies has a key role in industrial process automation. In this dissertation, ADAS systems and sensors for precision agriculture will be both treated. Several measurement procedures for characterizing commercial 3D LiDARs will be proposed and tested to cope with the growing need for comparison tools. Axial errors and transversal errors have been investigated. Moreover, a measurement method and setup for evaluating the fog effect on 3D LiDARs will be proposed. Each presented measurement procedure has been tested. The obtained results highlight the versatility and the goodness of the proposed approaches. Regarding the precision agriculture sensors, a measurement approach for the Moisture Content and density estimation of crop directly on the field is presented. The approach regards the employment of a Near Infrared spectrometer jointly with Partial Least Square statistical analysis. The approach and the model will be described together with a first laboratory prototype used to evaluate the NIRS approach. Finally, a prototype for on the field analysis is realized and tested. The test results are promising, evidencing that the proposed approach is suitable for Moisture Content and density estimation.

What Bees Want: Algorithm-Aided Design di un'arnia progettata per le api e realizzata in Additive Manufacturing

L’importanza delle api per la vita sulla Terra ed il rischio alle quali sono sottoposte per via dell’azione dell’uomo sono ormai un dato di fatto. La concezione antropocentrica della natura e l’allevamento al solo fine produttivo di questi piccoli insetti, ha da sempre danneggiato il loro habitat e interferito con i loro cicli biologici. L’apicoltura, nata come un rapporto mutualistico in cui l’uomo offriva un rifugio alle api e loro in cambio provvedevano al suo nutrimento, si è trasformato in una dannosa dipendenza ed in un assoggettamento di questi insetti ai ritmi artificiali e tutt’altro che naturali della produzione rapida e seriale volta all’ottenimento di un profitto. Un’evidente prova di questa condizione, sono i rifugi per le api, le arnie. Ci siamo mai chiesti perché le arnie hanno questa forma? È quella che preferiscono le api, o quella che rende più pratici e veloci processi di costruzione, gestione e produzione? In natura le api colonizzano cavità quali tronchi cavi di alberi, forme lontane, per non dire diametralmente opposte a quelle in cui le vediamo vivere negli allevamenti. In questa ottica, il design e le nuove tecnologie, poste al servizio della Natura, conducono ad un punto di incontro tra le esigenze umane e quelle degli altri esseri viventi, delle api in questo caso. I concetti di Additive Manufacturing e Design Computazionale, permettono processi di produzione simili a quelli evolutivi naturali e trovano per questa motivazione un’applicazione ideale per progetti che si pongono come fine quello di discostarsi da una visione troppo artificiale, per riavvicinarsi alla perfezione e all’armonia delle leggi della Natura.

Characterization of a 3D-printed low-cost flexible dielectric material for the realization of innovative WPT wearable applications

The aim of this thesis is to demonstrate that 3D-printing technologies can be considered significantly attractive in the production of microwave devices and in the antenna design, with the intention of making them lightweight, cheaper, and easily integrable for the production of wireless, battery-free, and wearable devices for vital signals monitoring. In this work, a new 3D-printable, low-cost resin material, the Flexible80A, is proposed as RF substrate in the implementation of a rectifying antenna (rectenna) operating at 2.45 GHz for wireless power transfer. A careful and accurate electromagnetic characterization of the abovementioned material, revealing it to be a very lossy substrate, has paved the way for the investigation of innovative transmission line and antenna layouts, as well as etching techniques, possible thanks to the design freedom enabled by 3D-printing technologies with the aim of improving the wave propagation performance within lossy materials. This analysis is crucial in the design process of a patch antenna, meant to be successively connected to the rectifier. In fact, many different patch antenna layouts are explored varying the antenna dimensions, the substrate etchings shape and position, the feeding line technology, and the operating frequency. Before dealing with the rectification stage of the rectenna design, the hot and long-discussed topic of the equivalent receiving antenna circuit representation is addressed, providing an overview of the interpretation of different authors about the issue, and the position that has been adopted in this thesis. Furthermore, two rectenna designs are proposed and simulated with the aim of minimizing the dielectric losses. Finally, a prototype of a rectenna with the antenna conjugate matched to the rectifier, operating at 2.45 GHz, has been fabricated with adhesive copper on a substrate sample of Flexible80A and measured, in order to validate the simulated results.

Recupero e riutilizzo di uno scarpone da sci a fine vita. Ottimizzazione del processo di Design for Recycling con simulazione agli elementi finiti validata tramite correlazione di immagini digitale

Il presente elaborato di tesi è parte di un ampio progetto finalizzato alla realizzazione di uno scarpone da sci ottenuto per il 90% di materiale da riciclo di scarponi da sci a fine vita. L’obiettivo è di realizzare la progettazione del nuovo scarpone, e caratterizzarne le proprietà flessionali avvalendosi ti tecniche di simulazione numerica FEM validata attraverso Correlazione di Immagini Digitale. La caratterizzazione flessionale è realizzata con la prova del Flex Test, che consiste nell’imporre una flessione dorsale ad una protesi di gamba. Le prime simulazioni FEM di questo complesso modello hanno evidenziato delle criticità. La presente ricerca, si pone l’obiettivo di risolvere singolarmente questi problemi. Inizialmente, si è realizzata la blend polimerica dei materiali dello scafo e del gambetto dello scarpone. Si è effettuata la caratterizzazione meccanica del materiale, confrontandolo con il materiale vergine. Si è poi ricercato il modello costitutivo più adeguato di materiale iperelastico per il FEM. Successivamente, si è ottenuto il modello CAD della scarpetta attraverso l’approccio reverse engineering, con la tecnica della scansione 3D, la quale ha consentito di ottenere il file. STEP da aggiungere al modello FEM. La conoscenza della geometria effettiva ha consentito di realizzare il design della nuova scarpetta ottenuta da materiale riciclato. Infine, si è utilizzata la Correlazione di Immagini Digitali per studiare la cinematica della chiusura dei ganci dello scafo, e per studiare lo stato di deformazione residua a chiusura effettuata. Si è valutata l’influenza del piede della protesi, e della scarpetta, durante la chiusura dei ganci. In seguito, si è confrontato quanto ottenuto dalle evidenze sperimentali della DIC, con la simulazione agli elementi finiti. Si tratta di un approccio innovativo, che vede per la prima volta implementata la Correlazione di Immagini Digitali per realizzare la caratterizzazione meccanica di uno scarpone da sci.