Analytic model for turn off in the silicon-on-insulator LIGBT

Lateral insulated gate bipolar transistors (LIGBTs) in silicon-on-insulator (SOI) show a unique turn off characteristic when compared to junction-isolated RESURF LIGBTs or vertical IGBTs. The turn off characteristic shows an extended `terrace' where, after the initial fast transient characteristic of IGBTs due to the loss of the electron current, the current stays almost at the same value for an extended period of time, before suddenly dropping to zero. In this paper, we show that this terrace arises because there is a value of LIGBT current during switch off where the rate of expansion of the depletion region with respect to the anode current is infinite. Once this level of anode current is approached, the depletion region starts to expand very rapidly, and is only stopped when it reaches the n-type buffer layer surrounding the anode. Once this happens, the current rapidly drops to zero. A quasi-static analytic model is derived to explain this behaviour. The analytically modelled turn off characteristic agrees well with that found by numerical simulation.

Soft turn-on of NPT IGBT under Active Voltage Control

In this paper the soft turn-on of NPT IGBT under Active Voltage Control (AVC) is presented. The AVC technique is able to control the IGBT switching trajectory according to a pre-defined reference signal generated by a FPGA chip. By applying a special designed reference signal at turn-on, the IGBT turn-on current overshoot and diode recovery can be optimized. Experiments of soft turn-on with different reference signal are presented in this paper. This technique can be used to reduce the switching stress on the device and on other components of the circuit. © 2011 IEEE.

Examining the possibilty of multiplication and breeding of (Schizothorav [sic] zarudnyi) in order to restoration of regional aquatics reservations of Hamoon Lake and taking its advantag [sic] for aquaculture

Schizothorax zarudnvi, is an endemic fish of east country waters. (Triple lagoons of Hamoon and relevant water resources) that in the world it is reported in this resource specially. This fish named Hamoon mahi is one of the most economically valuable species in this region. Because of the recent years droughts, Hamoon logoon has been drive since 2000. Also, semi-wells (a semi natural resource) were affected drastically by recent drought years and their volume reduced to nearly one third of their real volume and resulted in changing at growth and reproduction physiology process in Schizothorax zanidnyi, brood stocks. Beginning of this project was done from October 2003. It's field studies begun (brood catching) since November 2001 by two methods including entangling gairs and at semi wells of Sistan that (Beach seine) had maximum rate of preparing qualified brood stocks. Broods transferred to Cyprinidea reproduction work shop of Zahak and after taking primary measures they stored in to the edaphic pools. Increasing the success safety factor (coefficient) for artificial reproduction of Sthizothorax zarudnyi , identifying the appropriate tune for Hormonal acceptance (physiological preparation of broods) is needed , so this important work was done regularly by histological studies and GSI measurements since November. Highest GSI rates of females (%80.51) and highest IV stage abundance of sexual maturity (%l 00) were observed an march. On the base of this date, Hormone therapy was done on broods on march. The used hormones are as follows Hypophysis. extraction, GnRHa and Anti Dopamin at the dozes of 3-6 ml, 20-30kg and 10-15 ml per kg body weight respectively and 2-3 times from 11-12-80 they were injected. Injected broods kept in to two circumstances, flow-through (rounded pool) and stagnant systems. In stagnant system 14 and 19 individuals of female and male (Schizothorax zauiulnri) broods, respectively injected in 11th, 15111, 19th, and 24th of march 1380. Non of the injected broods in 11 and 15 and 19th march (in stagnant Condition) answered to Hormone therapy. After final injection broods had general less activity and a few of them died. Mean temperature of brood pond waters (daily) which were injected. Fluctuated between 10-25-13. 63°c but injected broods on 24th march had different characteristics. They had pale color and had few fecundity. In this stage of injection they hadn't any successful vulation. After injection, Mean daily water temperature was 15, 88-17, 54°c. In Flowing system, 13-16 individual of males and females respectively were injected on 15th, 19th, 22th and 23th march. None of injected producers on 15th and 19th march with mean daily water temperature of 10, 25-12°c were prepared for spawning but injected producers on 22nd an 23th march with mean daily water temperature of 13.5-1 rc responded about 75-100 percent. (Schizothorax zarudnyi) brood stocks were prepared for spawning after 353-428 hours/day from final injection. Diameter of obtained eggs (before fertilization) was between 1.9-2.3 min and of fertilized eggs was 3.8mm. Fertilized eggs of (Schizothorax zarudnyi) were hatched after 6-7 days with mean water temperature of 17.08°c. Mean length of on one day larvae was 9.47 mm. Larvae was 9.47 mm. Larvae adsorbed the whole yolk sac after , 5-6 days at 17- 1°c and were prepared for releasing in to edaphic pools. Because of the lack of necessary and complementary facilities in the region , they had to release them in to veniros and growing them for 8 days. At the end of 18th day , 35000 larvae (at first) released into an edaphic pond with a volume of 150m2. After growing them for one moth , mean length and weight of new hatched larvae was 29.41 mm and 1.12►r , respectively. With respect to results of this investigation , artificial reproduction of (Schizothorax zarudnyi) Can be possible at 14-17°C and flowing water with Hormonal treatment. It -s breeding has increased development than other cultural specious in the region. Due to high economical value of this specious in Sistan and ti-s specialization east waters of Iran and having high resistance and proper growth There is a need of it's development and reproduction and culture in fish culture fanns (edaphic ponds• two-purpose pools) at the region and country.

Investigation into IGBT dV/dt during turn-off and its temperature dependence

In many power converter applications, particularly those with high variable loads, such as traction and wind power, condition monitoring of the power semiconductor devices in the converter is considered desirable. Monitoring the device junction temperature in such converters is an essential part of this process. In this paper, a method for measuring the insulated gate bipolar transistor (IGBT) junction temperature using the collector voltage dV/dt at turn-OFF is outlined. A theoretical closed-form expression for the dV/dt at turn-OFF is derived, closely agreeing with experimental measurements. The role of dV/dt in dynamic avalanche in high-voltage IGBTs is also discussed. Finally, the implications of the temperature dependence of the dV/dt are discussed, including implementation of such a temperature measurement technique. © 2006 IEEE.

Turn-off failure mechanism in large area IGCTs

The destruction mechanism in large area IGCTs (Integrated Gate Commutated Thyristors) under inductive switching conditions is analyzed in detail. The three-dimensional nature of the turn-off process in a 91mm diameter wafer is simulated with a two-dimensional representation. Simulation results show that the final destruction is caused by the uneven dynamic avalanche current distribution across the wafer. © 2011 IEEE.

Industrial ecology at factory level: A prototype methodology

The concept of sustainable manufacturing is a form of pollution prevention that integrates environmental considerations in the production of goods while focusing on efficient resource use. Taking the industrial ecology perspective, this efficiency comes from improved resource flow management. The assessment of material, energy and waste resource flows, therefore, offers a route to viewing and analysing a manufacturing system as an ecosystem using industrial ecology biological analogy and can, in turn, support the identification of improvement opportunities in the material, energy and waste flows. This application of industrial ecology at factory level is absent from the literature. This article provides a prototype methodology to apply the concepts of industrial ecology using material, energy and waste process flows to address this gap in the literature. Various modelling techniques were reviewed and candidates selected to test the prototype methodology in an industrial case. The application of the prototype methodology showed the possibility of using the material, energy and waste resource flows through the factory to link manufacturing operations and supporting facilities, and to identify potential improvements in resource use. The outcomes of the work provide a basis to build the specifications for a modelling tool that can support those analysing their manufacturing system to improve their environmental performance and move towards sustainable manufacturing. © IMechE 2012.

A method for VVER-1000 fuel rearrangement optimization taking into account both fuel cladding durability and burnup

A method for VVER-1000 fuel rearrangement optimization that takes into account both cladding durability and fuel burnup and which is suitable for any regime of normal reactor operation has been established. The main stages involved in solving the problem of fuel rearrangement optimization are discussed in detail. Using the proposed fuel rearrangement efficiency criterion, a simple example VVER-1000 fuel rearrangement optimization problem is solved under deterministic and uncertain conditions. It is shown that the deterministic and robust (in the face of uncertainty) solutions of the rearrangement optimization problem are similar in principle, but the robust solution is, as might be anticipated, more conservative. © 2013 Elsevier B.V.

Fabrication, densification, and replica molding of 3D carbon nanotube microstructures

The introduction of new materials and processes to microfabrication has, in large part, enabled many important advances in microsystems, labon- a-chip devices, and their applications. In particular, capabilities for cost-effective fabrication of polymer microstructures were transformed by the advent of soft lithography and other micromolding techniques 1,2, and this led a revolution in applications of microfabrication to biomedical engineering and biology. Nevertheless, it remains challenging to fabricate microstructures with well-defined nanoscale surface textures, and to fabricate arbitrary 3D shapes at the micro-scale. Robustness of master molds and maintenance of shape integrity is especially important to achieve high fidelity replication of complex structures and preserving their nanoscale surface texture. The combination of hierarchical textures, and heterogeneous shapes, is a profound challenge to existing microfabrication methods that largely rely upon top-down etching using fixed mask templates. On the other hand, the bottom-up synthesis of nanostructures such as nanotubes and nanowires can offer new capabilities to microfabrication, in particular by taking advantage of the collective self-organization of nanostructures, and local control of their growth behavior with respect to microfabricated patterns. Our goal is to introduce vertically aligned carbon nanotubes (CNTs), which we refer to as CNT "forests", as a new microfabrication material. We present details of a suite of related methods recently developed by our group: fabrication of CNT forest microstructures by thermal CVD from lithographically patterned catalyst thin films; self-directed elastocapillary densification of CNT microstructures; and replica molding of polymer microstructures using CNT composite master molds. In particular, our work shows that self-directed capillary densification ("capillary forming"), which is performed by condensation of a solvent onto the substrate with CNT microstructures, significantly increases the packing density of CNTs. This process enables directed transformation of vertical CNT microstructures into straight, inclined, and twisted shapes, which have robust mechanical properties exceeding those of typical microfabrication polymers. This in turn enables formation of nanocomposite CNT master molds by capillary-driven infiltration of polymers. The replica structures exhibit the anisotropic nanoscale texture of the aligned CNTs, and can have walls with sub-micron thickness and aspect ratios exceeding 50:1. Integration of CNT microstructures in fabrication offers further opportunity to exploit the electrical and thermal properties of CNTs, and diverse capabilities for chemical and biochemical functionalization 3. © 2012 Journal of Visualized Experiments.

Modeling turn-off voltage rise in SOI LIGBT

The behavior of the drain voltage rise of the Lateral IGBT during inductive turn-off is studied in detail. Numerical simulations show that, if compared with the well known vertical IGBT, the Lateral IGBT presents a differences in the on-state stored charge and in the growth of the depleted region that result in a different drain voltage rise. In this paper a complete model for the voltage rise is devised through an accurate calculation of the equivalent output capacitance. The model is in excellent agreement with two-dimensional simulations. Further, the paper shows that previously proposed models, which targeted the vertical IGBT, are not adequate for the description of the turn-off voltage rise in the Lateral IGBT. © Springer Science + Business Media LLC 2006.

Optimised IGBT turn-off under active voltage control in PEBB applications

Active Voltage Control (AVC) is an implementation of classic Proportional-Derivative (PD) control and multi-loop feedback control to force an IGBT to follow a pre-set switching trajectory. Previously, AVC was mainly used for controlling series-connected IGBTs in order to enable voltage balance between IGBTs. In this paper, the nonlinear IGBT turn-off transient is further discussed and the turnoff of a single IGBT under AVC is further optimised in order to meet the demand of Power Electronic Building Block (PEBB) applications. © 2013 IEEE.