Hiontarobotti-solun tietojärjestelmä

Hiontarobotteja käytetään nopeuttamaan hiontaprosessia ja vähentämään henkilöiden tarvetta tehdä kuluttavaa ja raskasta työtä. Yleensä hiottavat kappaleet ovat suuria, jolloin hionta robotillakin kestää kauan. Kun hiottavat kappaleet ovat pieniä, robotti hioo kappaleen nopeasti. Tällöin tarvitaan automaattinen varastointi, jotta hiontarobotti pystyy jatkamaan nopeasti seuraavan kappaleen hiontaa. Automaattinen varastointi tarvitsee tiedonhallintajärjestelmän, jolla hallitaan varastossa olevien kappaleiden tietoja. Hiottava kappale täytyy esimerkiksi pystyä tunnistamaan ennen hionnan aloittamista. Yhtenä tunnistusmenetelmänä voidaan käyttää radiotaajuudella toimivia RFID-tunnisteita. Kun kappale tunnistetaan ennen hiontaa niin voidaan varmistua, että robotti suorittaa oikean hiontaohjelman kappaleelle. Diplomityö liittyy Master Automation Groupin ensimmäiseen automaattista varastoa hyödyntävään FlexMill™-hiontarobotti-soluun. Työssä on suunniteltu ja toteutettu tietokanta ja siihen liittyvä tietojärjestelmä. Kehitettävä ohjelma toimii solun toiminnasta vastaavan soluohjaimen tiedonhallintaosana. Ohjelma hyödyntää RFID-laitteita kappaleiden tunnistuksessa.

Learning Robot Motions from Visual Sensing

Learning from demonstration becomes increasingly popular as an efficient way of robot programming. Not only a scientific interest acts as an inspiration in this case but also the possibility of producing the machines that would find application in different areas of life: robots helping with daily routine at home, high performance automata in industries or friendly toys for children. One way to teach a robot to fulfill complex tasks is to start with simple training exercises, combining them to form more difficult behavior. The objective of the Master’s thesis work was to study robot programming with visual input. Dynamic movement primitives (DMPs) were chosen as a tool for motion learning and generation. Assuming a movement to be a spring system influenced by an external force, making this system move, DMPs represent the motion as a set of non-linear differential equations. During the experiments the properties of DMP, such as temporal and spacial invariance, were examined. The effect of the DMP parameters, including spring coefficient, damping factor, temporal scaling, on the trajectory generated were studied.

Uuden robottisolun ohjelmointitavan mahdollisuudet pienille ja keskisuurille yrityksille

Robotin ohjelmointi on aikaa vievää ja tarvitsee robotin ohjelmoinnin tuntevan operaattorin toimimaan robotin opettajana. Saadakseen robottisolun kustannustehokkaaksi operaattorilla olisi hyvä olla useampi solu hoidettavanaan samaan aikaan. Tämä ei ole suuri ongelma suurille yrityksille, joissa voi olla kymmeniä robottisoluja. Jos kyseessä on pieni tai keskisuuri yritys, automatisointi-investointi voi jäädä tekemättä ohjelmoinnin vaikeuden aiheuttaman ongelman vuoksi. Diplomityössä keskityttiin tutkimaan robotisointia pienten ja keskisuurten yritysten kannalta. Teoriaosassa on keskitytty robottisolun suunnittelun kannalta tarvittaviin perustietoihin robotin rakenteesta, ohjausjärjestelmästä, ohjelmoinnista sekä turvallisuudesta. Näiden perustietojen lisäksi on huomioitu hitsauksen automatisointia sekä taluttamalla ohjelmoitavan robottisolun tekninen konsepti. Taluttamalla ohjelmoitavan robottisolun konseptin käsittelyosassa on myös perehdytty taluttamalla ohjelmoinnin vaatimiin komponentteihin kuten voima/vääntö-anturi. Robottisolun suunnittelu on tehtävä koneasetuksen vaatimusten mukaan. Turvallisuus osiossa on käsitelty koneasetuksen vaatimuksia koneensuunnittelulle ja käytännön osassa on käsitelty Winnovan taluttamalla ohjelmoitavan robottisolun suunnittelua koneasetuksen ohjeiden mukaan. Käytännön osassa on tutkittu taluttamalla ohjelmoinnin tuomia etuja muihin ohjelmointimenetelmiin nähden sekä suoritettu investointilaskelmat taluttamalla ohjelmoitavasta ja opettamalla ohjelmoitavasta robottisolusta. Koetuloksista nähdään taluttamalla ohjelmoinnin olevan nopeampi ja yksinkertaisempi tapa ohjelmoida robottia kuin opettamalla ohjelmointi. Investointilaskelmien vertailusta nähdään taluttamalla ohjelmoinnin tulevan opettamalla ohjelmointia edullisemmaksi vaihtoehdoksi käyttökustannusten edullisuuden ansiosta.

Mobile Teleoperation of a Mobile Robot

This thesis describes the design and implementation of a graphical application on a mobile device to teleoperate a mobile robot. The department of information technology in Lappeenranta University conducts research in robotics, and the main motivation was to extend the available teleoperation applications for mobile devices. The challenge was to port existing robot software library onto an embedded device platform, then develop a suitable user interface application that provides sufficient functionality to perform teleoperation tasks over a wireless communication network. This thesis involved investigating previous teleoperation applications and conducted similar experiments to test and evaluate the designed application for functional activity and measure performance on a mobile device which have been identified and achieved. The implemented solution offered good results for navigation purposes particularly for teleoperating a visible robot and suggests solutions for exploration when no environment map for the operator is present.

Alumiiniveneen rungon modulointi robottihitsauksen tehostamiseksi

Alumiiniveneiden valmistuksessa hitsauksen automatisointiaste on hyvin matala. Kilpailukyvyn säilyttämiseksi on tärkeää saada automatisointiastetta nostettua ja tätä kautta hitsauskustannuksia alennettua. Automatisoinnin esteenä ei ole teknologian puute, vaan ongelmana on alumiiniveneiden rakenteen huono soveltuvuus automatisoituun tuotantoon. Rakenteen kehittäminen modulaariseksi on yksi mahdollisuus tehostaa robottihitsausta venerunkojen valmistuksessa. Tässä diplomityössä tutkittiin modulaarisuutta, modulointiin johtavia tekijöitä sekä modulaarisuudella mahdollisesti saavutettavia etuja valmistavassa teollisuudessa ja erityisesti robottihitsauksessa. Lisäksi käsiteltiin modulointiin läheisesti liittyvää valmistus- ja kokoonpanoystävällistä suunnittelua. Työssä tehtiin modulointiesimerkki huviveneen rungon robottihitsauksen tehostamiseksi. Veneen runko ja siihen suunniteltu jäykisterakennemoduuli mallinnettiin käyttäen SolidWorks-ohjelmistoa sekä Delmia V5-ohjelmistoon sisällytettyä Catia V5-suunnitteluympäristöä. Suunnitellun modulaarisen rakenteen hitsattavuutta ja hitsaukseen kuluvaa aikaa simuloitiin Delmia V5-ohjelmistolla. Modulaarisen rakenteen avulla robottihitsattavuutta on mahdollista tehostaa erityisesti rungon sisäisen jäykisterakenteen osalta. Kun tuotteesta on suurempi osa hitsattavissa robotin avulla, on myös robotisointi-investoinnit kannattavampia. Modulaarisuuden avulla voidaan päästä myös pienillä tuotantomäärillä sarjatuotannon etuihin, kun samaa moduulia voidaan käyttää vähäisillä muutoksilla useammassa eri venemallissa.

Challenges of business process automation for small and medium enterprises

The aim of the study was to examine problems that small and medium enterprises are facing during the implementation of business process automation projects. Study reveals problems from the point of view of companies who are implementing automation projects and from the point of view of IT-integrators who are specifying in IT solutions for small and medium companies.

Learning Robot Environment through Simulation

Traditionally simulators have been used extensively in robotics to develop robotic systems without the need to build expensive hardware. However, simulators can be also be used as a “memory”for a robot. This allows the robot to try out actions in simulation before executing them for real. The key obstacle to this approach is an uncertainty of knowledge about the environment. The goal of the Master’s Thesis work was to develop a method, which allows updating the simulation model based on actual measurements to achieve a success of the planned task. OpenRAVE was chosen as an experimental simulation environment on planning,trial and update stages. Steepest Descent algorithm in conjunction with Golden Section search procedure form the principle part of optimization process. During experiments, the properties of the proposed method, such as sensitivity to different parameters, including gradient and error function, were examined. The limitations of the approach were established, based on analyzing the regions of convergence.

Automated Software Testing in Machine Automation

The problem of software (SW) defaults is becoming more and more topical because of increasing amount of the SW and its complication. The majority of these defaults are founded during the test part that consumes about 40-50% of the development efforts. Test automation allows reducing the cost of this process and increasing testing effectiveness. In the middle of 1980 the first tools for automated testing appeared and the automated process was implemented in different kinds of SW testing. In short time, it became obviously, automated testing can cause many problems such as increasing product cost, decreasing reliability and even project fail. This thesis describes automated testing process, its concept, lists main problems, and gives an algorithm for automated test tools selection. Also this work presents an overview of the main automated test tools for embedded systems.

Automation Concept for Electrically Excited LV Synchronous Motor: Implementation into AC500 Programmable Logic Environment

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to develop an automation concept for controlling the electrically excited synchronous motor. Thesis concentrates on the implementation of the automation concept into the ABB’s AC500 programmable logic enviroment. The automation program was developed as a state machine with the ABB’s PS501 Control Builder software. For controlling the automation program is developed a fieldbus control and with CodeSys Visualization Tool a local control with control panel. The fieldbus control is done to correspond the ABB drives communication profile and the local control is implemented with a function block which feeds right control words into the statemachine. A field current control of the synchronous motor is realized as a method presented in doctoral thesis of Olli Pyrhönen (Pyrhönen 1998). The Method combines stator flux and torque based openloop control and power factor based feedback control.

Externally excited synchronous machine: Testing the automation concept

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to develop an automation concept for controlling the externally excited synchronous motor. Thesis concentrates on the testing planning and testing the system. Testing plan was made for three sectors: For the PLC program testing, for the communication testing and for the whole system testing. PLC program was tested with white box and destructive methods. Communication testing was done by switching maximum com-munication speed and checked if communication was reliable. Whole system testing included among other things speed and torque controlling. The system was tested with exploratory testing also. This enabled more reliable and broader testing than with systematical testing only.

Automation concept for an electrically excited synchronous motor: Setup and requirements specification

This bachelor’s thesis is a part of the research project realized in the summer 2011 in Lappeenranta University of Technology. The goal of the project was to create an automation concept for controlling an electrically excited synchronous motor. This thesis concentrates on the setup and requirements specification part of the concept. The setup consists of ABB AC500 as the PLC master device, DCS800 as an exciter and ACS800 as a frequency converter. The ACS800 frequency converter uses permanent magnet synchronous machine software to control the stator’s magnetic field, the DC drive handles the excitation and the AC500 PLC master controls the communication and functionality of the system. The requirements specification briefly explains the general over-view of the concept, the use and functionality of the PLC program and the requirements needed for the whole concept and the PLC program to work as intended.

Design and implementation of robot gripper interface

This thesis presents a design for an asynchronous interface to Robotiq adaptive gripper s-model. Designed interface is a communication layer that works on top of modbus layer. The design contains function definitions, finite state machine and exceptions. The design was not fully implemented but enough was so that it can be used. The implementation was done with c++ in linux environment. Additionally to the implementation a simple demo program was made to show the interface is used. Also grippers closing speed and force were measured. There is also a brief introduction into robotics and robot grasping.

Benefits and challenges of supply chain finance business process automation : A case study in ING Bank

Supply chain finance, a financial product provided by the bank, has gained increasing attention and popularity over the last few years. Supply chain finance helps the corporate clients to optimize their financial flows along the supply chain. One characteristic of supply chain finance is that it aims to provide automated solutions. Therefore, the business process automation of supply chain finance is a very interesting and important topic for study. In this study, the business process automation of supply chain finance within the case organization, ING, is analysed. The purpose is to: (1) Identify the benefits to understand the importance to automate supply chain finance business process; (2) Find out the existing automation degree in the supply chain finance business process within the case bank to see what’s the situation now and how to improve in the future; (3) Discover the challenges in the further automation of supply chain finance business process. Firstly, the study finds out that supply chain finance business process automation can bring many benefits to the bank. Automation can improve productivity by using less time and human labour in the business process, and by providing scalable solutions. Automation can also improve quality of the service by reducing the human errors. Last but not least, automation can improve internal governance by providing enhanced visibility of the business process. Because of these potential benefits, many banks are actively seeking solutions to automate their supply chain finance business process. Then, the current automation situation with the case bank is analysed with the help of business process modelling. The supply chain finance business process within the case bank can be further divided into several sub processes: daily transaction, buyer sales and setup, supplier onboarding, contract management, customer services and supports, and contract termination. The study finds out that the daily transaction process is already a highly automated, which is carried out through the web-based trading platform. However, for other business the automation degree is relatively low. Among these business processes, supplier onboarding is most needed for further automation. Then, some solutions are also suggested to automate the supplier onboarding business process. In the end, the study also foresees some challenges during the further automation of supply chain finance business process in the case bank. Some suggestions are also given to deal with these challenges.

A bridge between engineering and language learning : automation and German in an online course

Artikkeli luettavissa osassa: Part 2. - ISBN 9789522163172(PDF). - Liitteenä työpaperi