MicroRaman Spectroscopy of Si Nanowires: Influence of Size

Si Nanowires (NWs) were studied by Raman microspectroscopy. The Raman spectrum of the NWs reveals important thermal effects, which broaden and shift the one phonon Raman bands. The low thermal conductivity of the NWs and the low thermal dissipation are responsible for the temperature enhancement in the NW under the excitation with the laser beam. We have modeled, using finite element methods, the interaction between the laser beam and the NWs. The Raman spectrum of Si NWs is interpreted in terms of the temperature induced by the laser beam excitation, in correlation with finite element methods (fem) for studying the interaction between the laser beam and the NWs.

Efficient computation of the pressures developed during high-speed train passing events

The paper resumes the results obtained applying various implementations of the direct boundary element method (BEM) to the solution of the Laplace Equation governing the potential flow problem during everyday service manoeuvres of high-speed trains. In particular the results of train passing events at three different speed combinations are presented. Some recommendations are given in order to reduce calculation times which as is demonstrated can be cut down to not exceed reasonable limits even when using nowadays office PCs. Thus the method is shown to be a very valuable tool for the design engineer.

Dynamic stiffness analysis of bridge abutments

Strong motion records obtained in instrumented short-span bridges show the importance of the abutments in the dynamic response of the structure. Existing models study the pier foundation influence but not the abutment performance. This work proposes two and three dimensional boundary element models in the frequency domain and studies the dimensionless dynamic stiffness of standard bridge abutments.

Dynamic impedances of bridge abutments

The soil-structure interaction at bridge abutments may introduce important changes in the dynamic properties of short to medium span bridges. The paper presents the results obtained, through the use of the Boundary Element Method (B.E.M.) technique in several typical situations, including semiinfinite and layered media. Both stiffness and damping properties are included.

Crack mechanical failure in lithium niobate crystal under ion irradiation; novel simulation by extended finite elements

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion-generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Crack mechanical failure in ceramic materials under ion irradiation: case of lithium niobate crystal

Swift heavy ion irradiation (ions with mass heavier than 15 and energy exceeding MeV/amu) transfer their energy mainly to the electronic system with small momentum transfer per collision. Therefore, they produce linear regions (columnar nano-tracks) around the straight ion trajectory, with marked modifications with respect to the virgin material, e.g., phase transition, amorphization, compaction, changes in physical or chemical properties. In the case of crystalline materials the most distinctive feature of swift heavy ion irradiation is the production of amorphous tracks embedded in the crystal. Lithium niobate is a relevant optical material that presents birefringence due to its anysotropic trigonal structure. The amorphous phase is certainly isotropic. In addition, its refractive index exhibits high contrast with those of the crystalline phase. This allows one to fabricate waveguides by swift ion irradiation with important technological relevance. From the mechanical point of view, the inclusion of an amorphous nano-track (with a density 15% lower than that of the crystal) leads to the generation of important stress/strain fields around the track. Eventually these fields are the origin of crack formation with fatal consequences for the integrity of the samples and the viability of the method for nano-track formation. For certain crystal cuts (X and Y), these fields are clearly anisotropic due to the crystal anisotropy. We have used finite element methods to calculate the stress/strain fields that appear around the ion- generated amorphous nano-tracks for a variety of ion energies and doses. A very remarkable feature for X cut-samples is that the maximum shear stress appears on preferential planes that form +/-45º with respect to the crystallographic planes. This leads to the generation of oriented surface cracks when the dose increases. The growth of the cracks along the anisotropic crystal has been studied by means of novel extended finite element methods, which include cracks as discontinuities. In this way we can study how the length and depth of a crack evolves as function of the ion dose. In this work we will show how the simulations compare with experiments and their application in materials modification by ion irradiation.

Modelling of Topographic Irregularities for Seismic Site Response

Seismic evaluation methodology is applied to an existing viaduct in the south of Spain, near Granada, which is a medium seismicity region. The influence of both geology and topography in the spatial variability of ground motion are studied as well as seismic hazard analysis and ground motion characterization. Artificial hazard-consistent ground motion records are synthesised applying seismic hazard analysis and site effects are estimated through a diffraction study. Direct BEM is used to calculate the valley displacement response to vertically propagating SV waves and transfer functions are generated allowing the transformation of free field motion to motion at each support. A closed formulae is used to estimate these transfer function. Finally, the results obtained are compared.

Interaction between a laser beam and semiconductor nanowires: application to the raman spectrum of Si nanowires

One presents in this work the study of the interaction between a focused laser beam and Si nanowires (NWs). The NWs heating induced by the laser beam is studied by solving the heat transfer equation by finite element methods (fem). This analysis permits to establish the temperature distribution inside the NW when it is excited by the laser beam. The overheating is dependent on the dimensions of the NW, both the diameter and the length. When performing optical characterization of the NWs using focused laser beams, one has to consider the temperature increase introduced by the laser beam. An important issue concerns the fact that the NWs diameter has subwavelength dimensions, and is also smaller than the focused laser beam. The analysis of the thermal behaviour of the NWs under the excitation with the laser beam permits the interpretation of the Raman spectra of Si NWs, where it is demonstrated that temperature induced by the laser beam play a major role in shaping the Raman spectrum of Si NWs

A Three-Dimensional B.I.E.M. Program

The program PECET (Boundary Element Program in Three-Dimensional Elasticity) is presented in this paper. This program, written in FORTRAN V and implemen ted on a UNIVAC 1100,has more than 10,000 sentences and 96 routines and has a lot of capabilities which will be explained in more detail. The object of the program is the analysis of 3-D piecewise heterogeneous elastic domains, using a subregionalization process and 3-D parabolic isopara, metric boundary elements. The program uses special data base management which will be described below, and the modularity followed to write it gives a great flexibility to the package. The Method of Analysis includes an adaptive integration process, an original treatment of boundary conditions, a complete treatment of body forces, the utilization of a Modified Conjugate Gradient Method of solution and an original process of storage which makes it possible to save a lot of memory.

On the use of trenches and walls on the control of ground transmitted railway vibrations

An actual case of an underground railway in the neighbourhood of habitation buildings has been analyzed. The study has been based on a twodimensional BEM model including a tunnel and a typical building. The soil properties were obtained using geophysical techniques. After a sensitivity study, the model has been simplyfied and validated by comparison with "in situ" measurements. Using this simplyfied model, a parametric study has been done including trenches and walls of different materials and different depths at two different distances from the tunnel. The reductions obtained with the different solutions can then be compared.

Development of FEM/BEM and SEA models from experimental results for structural elements with attached equipment

This work focuses on the analysis of a structural element of MetOP-A satellite. Given the special interest in the influence of equipment installed on structural elements, the paper studies one of the lateral faces on which the Advanced SCATterometer (ASCAT) is installed. The work is oriented towards the modal characterization of the specimen, describing the experimental set-up and the application of results to the development of a Finite Element Method (FEM) model to study the vibro-acoustic response. For the high frequency range, characterized by a high modal density, a Statistical Energy Analysis (SEA) model is considered, and the FEM model is used when modal density is low. The methodology for developing the SEA model and a compound FEM and Boundary Element Method (BEM) model to provide continuity in the medium frequency range is presented, as well as the necessary updating, characterization and coupling between models required to achieve numerical models that match experimental results.

Guía de introducción al Método de los Elementos de Contorno

Entre la impresionante floración de procedimientos de cálculo, provocada por la aplicación intensiva del ordenador, el llamado Método de los Elementos de Contorno (Boundary Element Method o Boundary Integral Equation Method) parece afianzarse como una alternativa útil al omnipresente Método de los Elementos Finitos que ya ha sido incorporado, como una herramienta de trabajo más, al cotidiano quehacer de la ingeniería. En España, tras unos intentos precursores que se señalan en el texto, la actividad más acusada en su desarrollo y mejora se ha centrado alrededor del Departamento que dirige uno de los autores. Después de la tesis doctoral de J. Domínguez en 1977 que introdujo en España la técnica del llamado "método directo", se han producido numerosas aportaciones en forma de artículos o tesis de investigación que han permitido alcanzar un nivel de conocimientos notable. En esta obrita se pretende transmitir parte de la experiencia adquirida, siquiera sea a nivel elemental y en un campo limitado de aplicación. La filosofía es semejante a la del pequeño libro de Hinton y Owen "A simple guide to finite elements" (Pineridge Press, 1980) que tanta aceptación ha tenido entre los principiantes. El libro se articula alrededor de un sólo tema, la solución del problema de Laplace, y se limitan los desarrollos matemáticos al mínimo imprescindible para el fácil seguimiento de áquel. Tras unos capítulos iniciales de motivación y centrado se desarrolla la técnica para problemas planos, tridimensionales y axisimétricos, limitando los razonamientos a los elementos más sencillos de variación constante o lineal. Finalmente, se incluye un capítulo descriptivo donde se avizoran temas que pueden provocar un futuro interés del estudioso. Para completar la información se ha añadido un apéndice en el que se recoge un pequeño programa para microordenador, con el objetivo de que se contemple la sencillez de programación para el caso plano. El programa es mejorable en muchos aspectos pero creemos que, con ello, mantiene un nivel de legibilidad adecuado para que el lector ensaye sobre él las modificaciones que se indican en los ejercicios al final del capítulo y justamente la provocación de ese aprendizaje es nuestro objetivo final.

Interaction between a laser beam and semiconductor nanowires: application to the raman spectrum of Si nanowires

One presents in this work the study of the interaction between a focused laser beam and Si nanowires (NWs). The NWs heating induced by the laser beam is studied by solving the heat transfer equation by finite element methods (FEM). This analysis permits to establish the temperature distribution inside the NW when it is excited by the laser beam. The overheating is dependent on the dimensions of the NW, both the diameter and the length. When performing optical characterisation of NWs using focused laser beams, one has to consider the temperature increase introduced by the laser beam. An important issue concerns the fact that the NW's diameter has subwavelength dimensions, and is also smaller than the focused laser beam. The analysis of the thermal behaviour of the NWs under the excitation with the laser beam permits the interpretation of the Raman spectrum of Si NWs. It is demonstrated that the temperature increase induced by the laser beam plays a major role in shaping the Raman spectrum of Si NWs.

Influencia de un fluido en las características dinámicas de placas circulares y casicirculares

La influencia de un fluido en las características dinámicas de estructuras se ha estudiado desde hace tiempo. Sin embargo muchos estudios se refieren a aplicaciones bajo el agua, como es el caso del sonar de un submarino por lo que el fluido circundante se considera líquido (sin efectos de compresibilidad). Más recientemente en aplicaciones acústicas y espaciales tales como antenas o paneles muy ligeros, ha sido estudiada la influencia en las características dinámicas de una estructura rodeada por un fluido de baja densidad. Por ejemplo se ha mostrado que el efecto del aire en el transmisor-reflector del Intelsat VI C-B con un diámetro de 3,2 metros y con un peso de sólo 34,7 kg disminuye la primera frecuencia en torno a un 20% con respecto a su valor en vacío. Por tanto es importante en el desarrollo de estas grandes y ligeras estructuras disponer de un método con el que estimar el efecto del fluido circundante sobre las frecuencias naturales de éstas. De esta manera se puede evitar el ensayo de la estructura en una cámara de vacío que para el caso de una gran antena o panel puede ser difícil y costoso. Se ha desarrollado un método de elementos de contorno (BEM) para la determinación del efecto del fluido en las características dinámicas de una placa circular. Una vez calculados analíticamente los modos de vibración de la placa en vacío, la matriz de masa añadida debido a la carga del fluido se determina por el método de elementos de contorno. Este método utiliza anillos circulares de manera que el número de elementos para obtener unos resultados precisos es muy bajo. Se utiliza un procedimiento de iteración para el cálculo de las frecuencias naturales del acoplamiento fluido-estructura para el caso de fluido compresible. Los resultados del método se comparan con datos experimentales y otros modelos teóricos mostrando la precisión y exactitud para distintas condiciones de contorno de la placa. Por otro lado, a veces la geometría de la placa no es circular sino casi-circular y se ha desarrollado un método de perturbaciones para determinar la influencia de un fluido incompresible en las características dinámicas de placas casi-circulares. El método se aplica a placas con forma elíptica y pequeña excentricidad. Por una parte se obtienen las frecuencias naturales y los modos de deformación de la placa vibrando en vacío. A continuación, se calculan los coeficientes adimensionales de masa virtual añadida (factores NAVMI). Se presentan los resultados de estos factores y el efecto del fluido en las frecuencias naturales. ABSTRACT The influence of the surrounding fluid on the dynamic characteristics of structures has been well known for many years. However most of these works were more concerned with underwater applications, such as the sonar of a submarine and therefore the surrounding fluid was considered a liquid (negligible compressibility effects). Recently for acoustical and spatial applications such as antennas or very light panels the influence on the dynamic characteristics of a structure surrounded by a fluid of low density has been studied. Thus it has been shown that the air effect for the Intelsat VI C-B transmit reflector with a diameter of 3,2 meters and weighting only 34,7 kg decreases the first modal frequency by 20% with respect to the value in vacuum. It is important then, in the development of these light and large structures to have a method that estimates the effect that the surrounding fluid will have on the natural frequencies of the structure. In this way it can be avoided to test the structure in a vacuum chamber which for a large antenna or panel can be difficult and expensive A BEM method for the determination of the effect of the surrounding fluid on the dynamic characteristics of a circular plate has been developed. After the modes of the plate in vacuum are calculated in an analytical form, the added mass matrix due to the fluid loading is determined by a boundary element method. This method uses circular rings so the number of elements to obtain an accurate result is very low. An iteration procedure for the computation of the natural frequencies of the couple fluid-structure system is presented for the case of the compressibility effect of air. Comparisons of the present method with various experimental data and other theories show the efficiency and accuracy of the method for any support condition of the plate. On the other hand, sometimes the geometry of the plate is not circular but almost-circular, so a perturbation method is developed to determine the influence of an incompressible fluid on the dynamic characteristics of almost-circular plates. The method is applied to plates of elliptical shape with low eccentricity. First, the natural frequencies and the mode shapes of the plate vibrating in vacuum are obtained. Next, the nondimensional added virtual mass coefficients (NAVMI factors) are calculated. Results of this factors and the effect of the fluid on the natural frequencies are presented.

Análisis mediante elementos finitos del comportamiento de losas de hormigón armado sometidas a explosiones

Se presenta en este trabajo una investigación sobre el comportamiento de losas de hormigón armado sometidas a explosiones y la simulación numérica de dicho fenómeno mediante el método de los elementos finitos. El trabajo aborda el estudio de la respuesta de dichos elementos estructurales por comparación entre los resultados obtenidos en ensayos reales a escala 1:1 y los cálculos realizados mediante modelos de ordenador. Este procedimiento permite verificar la idoneidad, o no, de estos últimos. Se expone en primer lugar el comportamiento mecánico de los modelos de material que son susceptibles de emplearse en la simulación de estructuras mediante el software empleado en la presente investigación, así como las diferentes formas de aplicar cargas explosivas en estructuras modeladas mediante el método de los Elementos Finitos, razonándose en ambos casos la elección llevada a cabo. Posteriormente, se describen los ensayos experimentales disponibles, que tuvieron lugar en las instalaciones del Laboratorio de Balística de Efectos, perteneciente al Instituto Tecnológico de la Marañosa (ITM), de Madrid, para estudiar el comportamiento de losas de hormigón armado a escala 1:1 sometidas a explosiones reales. Se ha propuesto un método de interpretación del nivel de daño en las losas mediante el martillo de Schmidt, que posteriormente permitirá comparar resultados con los modelos de ordenador realizados. Asimismo, se propone un método analítico para la determinación del tamaño óptimo de la malla en las simulaciones realizadas, basado en la distribución de la energía interna del sistema. Es conocido que el comportamiento de los modelos pueden verse fuertemente influenciados por el mallado empleado. Según el mallado sea “grosero” o “fino” el fallo puede no alcanzarse o hacerlo de forma prematura, o excesiva, respectivamente. Es más, algunos modelos de material contemplan una “regularización” del tamaño de la malla, pero en la presente investigación se evidencia que dicho procedimiento tiene un rango de validez limitado, incluso se determina un entorno óptimo de valores. Finalmente, se han elaborado los modelos numéricos con el software comercial LS-DYNA, contemplando todos los aspectos reseñados en los párrafos anteriores, procediendo a realizar una comparación de los resultados obtenidos en las simulaciones con los procedidos en los ensayos reales a escala 1:1, observando que existe una muy buena correlación entre ambas situaciones que evidencian que el procedimiento propuesto en la investigación es de todo punto adecuado para la simulación de losas de hormigón armado sometidas a explosiones. ABSTRACT This doctoral thesis presents an investigation on the behavior of reinforced concrete slabs subjected to explosions along with the numerical simulation of this phenomenon by the finite elements method. The work involves the study of the response of these structural elements by comparing the results of field tests at full scale and the calculations performed by the computer model. This procedure allows to verify the appropriateness or not of the latter. Firstly, the mechanical behavior of the material models that are likely to be used in the modelling of structures is explained. In addition, different ways of choosing explosive charges when conducting finite element methods are analyzed and discussed. Secondly, several experimental tests, which took place at the Laboratorio de Balística de Efectos at the Instituto Tecnológico de la Marañosa (ITM), in Madrid, are described in order to study the behavior of these reinforced concrete slabs. A method for the description of the slab damage level by the Schmidt hammer is proposed, which will make possible to compare the modelling results extracted from the computation experiments. Furthermore, an analytical method for determining the optimal mesh size to be used in the simulations is proposed. It is well known that the behavior of the models can be strongly influenced by the mesh size used. According to this, when modifiying the meshing density the damaged cannot be reached or do it prematurely, or excessive, respectively. Moreover, some material models include a regularization of the mesh size, but the present investigation evidenced that this procedure has a limited range of validity, even an optimal environment values are determined. The method proposed is based on the distribution of the internal energy of the system. Finally, several expecific numerical models have been performed by using LS-DYNA commercial software, considering all the aspects listed in the preceding paragraphs. Comparisons of the results extracted from the simulations and full scale experiments were carried out, noting that there exists a very good correlation between both of them. This fact demonstrates that the proposed research procedure is highly suitable for the modelling of reinforced concrete slabs subjected to blast loading.