Thermal-Hydraulic Studies on the Safety Of VVER-440 Type Nuclear Power Plants

This thesis includes several thermal hydraulic analyses related to the Loviisa WER 440 nuclear power plant units. The work consists of experimental studies, analysis of the experiments, analysis of some plant transits and development of a calculational model for calculation of boric acid concentrations in the reactor. In the first part of the thesis, in the case of won of boric acid solution behaviour during long term cooling period of LOCAs, experiments were performed in scaled down test facilities. The experimental data together with the results of RELAPS/MOD3 simulations were used to develop a model for calculations of boric acid concentrations in the reactor during LOCAs. The results of calculations showed that margins to critical concentrations that would lead to boric acid crystallization were large, both in the reactor core and in the lower plenum. This was mainly caused by the fact that water in the primary cooling circuit includes borax (Na)BsO,.IOHZO), which enters the reactor when ECC water is taken from the sump and greatly increases boric acid solubility in water. In the second part, in the case of simulation of horizontal steam generators, experiments were performed with PACTEL integral test loop to simulate loss of feedwater transients. The PACTEL experiments, as well as earlier REWET III natural circulation tests, were analyzed with RELAPS/MOD3 Version Sm5 code. The analysis showed that the code was capable of simulating the main events during the experiments. However, in the case of loss of secondary side feedwater the code was not completely capable to simulate steam superheating in the secondary side of the steam generators. The third part of the work consists of simulations of Loviisa VVER reactor pump trip transients with RELAPSlMODI Eur, RELAPS/MOD3 and CATHARE codes. All three codes were capable to simulate the two selected pump trip transients and no significant differences were found between the results of different codes. Comparison of the calculated results with the data measured in the Loviisa plant also showed good agreement.

Maritime Safety in the Gulf of Finland. Review on Policy Instruments

Suomenlahden lisääntynyt meriliikenne on herättänyt huolta meriliikenteen turvallisuuden tasosta, ja erityisesti Venäjän öljyviennin kasvu on lisännyt öljyonnettomuuden todennäköisyyttä Suomenlahdella. Erilaiset kansainväliset, alueelliset ja kansalliset ohjauskeinot pyrkivät vähentämään merionnettomuuden riskiä ja meriliikenteen muita haittavaikutuksia. Tämä raportti käsittelee meriturvallisuuden yhteiskunnallisia ohjauskeinoja: ohjauskeinoja yleisellä tasolla, meriturvallisuuden keskeisimpiä säätelijöitä, meriturvallisuuden ohjauskeinoja ja meriturvallisuuspolitiikan tulevaisuuden näkymiä, ohjauskeinojen tehokkuutta ja nykyisen meriturvallisuuden ohjausjärjestelmän heikkouksia. Raportti on kirjallisuuskatsaus meriturvallisuuden yhteiskunnalliseen sääntelyn rakenteeseen ja tilaan erityisesti Suomenlahden meriliikenteen näkökulmasta. Raportti on osa tutkimusprojektia ”SAFGOF - Suomenlahden meriliikenteen kasvunäkymät 2007 - 2015 ja kasvun vaikutukset ympäristölle ja kuljetusketjujen toimintaan” ja sen työpakettia 6 ”Keskeisimmät riskit ja yhteiskunnalliset vaikutuskeinot”. Yhteiskunnalliset ohjauskeinot voidaan ryhmitellä hallinnollisiin, taloudellisiin ja tietoohjaukseen perustuviin ohjauskeinoihin. Meriturvallisuuden edistämisessä käytetään kaikkia näitä, mutta hallinnolliset ohjauskeinot ovat tärkeimmässä asemassa. Merenkulun kansainvälisen luonteen vuoksi meriturvallisuuden sääntely tapahtuu pääosin kansainvälisellä tasolla YK:n ja erityisesti Kansainvälisen merenkulkujärjestön (IMO) toimesta. Lisäksi myös Euroopan Unionilla on omaa meriturvallisuuteen liittyvää sääntelyä ja on myös olemassa muita alueellisia meriturvallisuuden edistämiseen liittyviä elimiä kuten HELCOM. Joitakin meriturvallisuuden osa-alueita säädellään myös kansallisella tasolla. Hallinnolliset meriturvallisuuden ohjauskeinot sisältävät aluksen rakenteisiin ja varustukseen, alusten kunnon valvontaan, merimiehiin ja merityön tekemiseen sekä navigointiin liittyviä ohjauskeinoja. Taloudellisiin ohjauskeinoihin kuuluvat esimerkiksi väylä- ja satamamaksut, merivakuutukset, P&I klubit, vastuullisuus- ja korvauskysymykset sekä taloudelliset kannustimet. Taloudellisten ohjauskeinojen käyttö meriturvallisuuden edistämiseen on melko vähäistä verrattuna hallinnollisten ohjauskeinojen käyttöön, mutta niitä voitaisiin varmasti käyttää enemmänkin. Ongelmana taloudellisten ohjauskeinojen käytössä on se, että ne kuuluvat pitkälti kansallisen sääntelyn piiriin, joten alueellisten tai kansainvälisten intressien edistäminen taloudellisilla ohjauskeinoilla voi olla hankalaa. Tieto-ohjaus perustuu toimijoiden vapaaehtoisuuteen ja yleisen tiedotuksen lisäksi tieto-ohjaukseen sisältyy esimerkiksi vapaaehtoinen koulutus, sertifiointi tai meriturvallisuuden edistämiseen tähtäävät palkinnot. Poliittisella tasolla meriliikenteen aiheuttamat turvallisuusriskit Suomenlahdella on otettu vakavasti ja paljon työtä tehdään eri tahoilla riskien minimoimiseksi. Uutta sääntelyä on odotettavissa etenkin liittyen meriliikenteen ympäristövaikutuksiin ja meriliikenteen ohjaukseen kuten meriliikenteen sähköisiin seurantajärjestelmiin. Myös inhimilliseen tekijän merkitykseen meriturvallisuuden kehittämisessä on kiinnitetty lisääntyvissä määrin huomiota, mutta inhimilliseen tekijän osalta tehokkaiden ohjauskeinojen kehittäminen näyttää olevan haasteellista. Yleisimmin lääkkeeksi esitetään koulutuksen kehittämistä. Kirjallisuudessa esitettyjen kriteereiden mukaan tehokkaiden ohjauskeinojen tulisi täyttää seuraavat vaatimukset: 1) tarkoituksenmukaisuus – ohjauskeinojen täytyy olla sopivia asetetun tavoitteen saavuttamiseen, 2) taloudellinen tehokkuus – ohjauskeinon hyödyt vs. kustannukset tulisi olla tasapainossa, 3) hyväksyttävyys – ohjauskeinon täytyy olla hyväksyttävä asianosaisten ja myös laajemman yhteiskunnan näkökulmasta katsottuna, 4) toimeenpano – ohjauskeinon toimeenpanon pitää olla mahdollista ja sen noudattamista täytyy pystyä valvomaan, 5) lateraaliset vaikutukset – hyvällä ohjauskeinolla on positiivisia seurannaisvaikutuksia muutoinkin kuin vain ohjauskeinon ensisijaisten tavoitteiden saavuttaminen, 6) kannustin ja uuden luominen – hyvä ohjauskeino kannustaa kokeilemaan uusia ratkaisuja ja kehittämään toimintaa. Meriturvallisuutta koskevaa sääntelyä on paljon ja yleisesti ottaen merionnettomuuksien lukumäärä on ollut laskeva viime vuosikymmenien aikana. Suuri osa sääntelystä on ollut tehokasta ja parantanut turvallisuuden tasoa maailman merillä. Silti merionnettomuuksia ja muita vaarallisia tapahtumia sattuu edelleen. Nykyistä sääntelyjärjestelmää voidaan kritisoida monen asian suhteen. Kansainvälisen sääntelyn aikaansaaminen ei ole helppoa: prosessi on yleensä hidas ja tuloksena voi olla kompromissien kompromissi. Kansainvälinen sääntely on yleensä reaktiivista eli ongelmakohtiin puututaan vasta kun jokin onnettomuus tapahtuu sen sijaan että se olisi proaktiivista ja pyrkisi puuttumaan ongelmakohtiin jo ennen kuin jotain tapahtuu. IMO:n työskentely perustuu kansallisvaltioiden osallistumiseen ja sääntelyn toimeenpano tapahtuu lippuvaltioiden toimesta. Kansallisvaltiot ajavat IMO:ssa pääasiallisesti omia intressejään ja sääntelyn toimeenpanossa on suuria eroja lippuvaltioiden välillä. IMO:n kyvyttömyys puuttua havaittuihin ongelmiin nopeasti ja ottaa sääntelyssä huomioon paikallisia olosuhteita on johtanut siihen, että esimerkiksi Euroopan Unioni on alkanut itse säädellä meriturvallisuutta ja että on olemassa sellaisia alueellisia erityisjärjestelyjä kuin PSSA (particularly sensitive sea area – erityisen herkkä merialue). Merenkulkualalla toimii monenlaisia yrityksiä: toisaalta yrityksiä, jotka pyrkivät toimimaan turvallisesti ja kehittämään turvallisuutta vielä korkeammalle tasolle, ja toisaalta yrityksiä, jotka toimivat niin halvalla kuin mahdollista, eivät välitä turvallisuusseikoista, ja joilla usein on monimutkaiset ja epämääräiset omistusolosuhteet ja joita vahingon sattuessa on vaikea saada vastuuseen. Ongelma on, että kansainvälisellä merenkulkualalla kaikkien yritysten on toimittava samoilla markkinoilla. Vastuuttomien yritysten toiminnan mahdollistavat laivaajat ja muut alan toimijat, jotka suostuvat tekemään yhteistyötä niiden kanssa. Välinpitämätön suhtautuminen turvallisuuteen johtuu osaksi myös merenkulun vanhoillisesta turvallisuuskulttuurista. Verrattaessa meriturvallisuuden sääntelyjärjestelmää kokonaisuutena tehokkaiden ohjauskeinoihin kriteereihin, voidaan todeta, että monien kriteerien osalta nykyistä järjestelmää voidaan pitää tehokkaana ja onnistuneena. Suurimmat ongelmat lienevät sääntelyn toimeenpanossa ja ohjauskeinojen kustannustehokkuudessa. Lippuvaltioiden toimeenpanoon perustuva järjestelmä ei toimi toivotulla tavalla, josta mukavuuslippujen olemassa olo on selvin merkki. Ohjauskeinojen, sekä yksittäisten ohjauskeinojen että vertailtaessa eri ohjauskeinoja keskenään, kustannustehokkuutta on usein vaikea arvioida, minkä seurauksena ohjauskeinojen kustannustehokkuudesta ei ole saatavissa luotettavaa tietoa ja tuloksena voi olla, että ohjauskeino on käytännössä pienen riskin eliminoimista korkealla kustannuksella. Kansainvälisen tason meriturvallisuus- (ja merenkulku-) politiikan menettelytavoiksi on ehdotettu myös muita vaihtoehtoja kuin nykyinen järjestelmä, esimerkiksi monitasoista tai polysentristä hallintojärjestelmää. Monitasoisella hallintojärjestelmällä tarkoitetaan järjestelmää, jossa keskushallinto on hajautettu sekä vertikaalisesti alueellisille tasoille että horisontaalisesti ei-valtiollisille toimijoille. Polysentrinen hallintojärjestelmä menee vielä askeleen pidemmälle. Polysentrinen hallintojärjestelmä on hallintotapa, jonka puitteissa kaikentyyppiset toimijat, sekä yksityiset että julkiset, voivat osallistua hallintoon, siis esimerkiksi hallitukset, edunvalvontajärjestöt, kaupalliset yritykset jne. Kansainvälinen lainsäädäntö määrittelee yleiset tasot, mutta konkreettiset toimenpiteet voidaan päättää paikallisella tasolla eri toimijoiden välisessä yhteistyössä. Tämän tyyppisissä hallintojärjestelmissä merenkulkualan todellinen, kansainvälinen mutta toisaalta paikallinen, toimintaympäristö tulisi otetuksi paremmin huomioon kuin järjestelmässä, joka perustuu kansallisvaltioiden keskenään yhteistyössä tekemään sääntelyyn. Tällainen muutos meriturvallisuuden hallinnassa vaatisi kuitenkin suurta periaatteellista suunnanmuutosta, jollaisen toteutumista ei voi pitää kovin todennäköisenä ainakaan lyhyellä tähtäimellä.

Work for your happiness - Theoretical and empirical study defining and measuring happiness at work

There are vast changes in the work environment, and the traditional rules and management methods might not be suitable for today’s employees anymore. The meaning of work is also changing due to the younger and higher educated generations entering the markets. Old customs need to be re-validated and new approaches should be taken into use. This paper strongly emphasizes the importance of happiness research and happiness at work. The values towards the meaning of work are changing; people demand happiness and quality from all aspects of their lives. The aim of this study is to define happiness - especially at work - and to explain how it can be measured and what kind of results achieved. I also want to find out how the contents of work and the working environment might enhance happiness. The correlation between education and happiness is discussed and examined. I am aware that the findings and theories are concentrating mainly on Western Countries and highlighting the values and work-environments of those societies. The main aim of the empirical study is to find out if there are connections between happiness and work in data collected by World Value Survey in 2005, and if the profession has effects on happiness. Other factors such as the correlation of age, sex, education and income are examined too. I also want to find out what kind of values people have towards work and how these affect the happiness levels. The focus is on two nations: Finland (N=1014) and Italy (N=1012). I have also taken the global comparison within, that is all 54 countries (N=66,566) included in the 5th wave (during the years 2005 -2008) of the World Value Survey. The results suggest that people are generally happy around the world; happiness decreasing with the age, the educated being happier than the uneducated and the employed happier than the unemployed. People working in neat “white collar” jobs are more likely happier than those working in factories or outdoors. Money makes us happier, until certain level is reached. Work is important to people and the importance of work adds happiness. Work is also highly appreciated, but there are more happy people among those who do not appreciate work that highly. Safety matters the most when looking for a job, and there are more happy people among those who have selected the importance of work as the first choice when looking for a job, than among those to whom an income is the most important aspect. People are more likely happy when the quality of work is high, that is when their job consists of creative and cognitive tasks and when they have a feeling of independence.

Overview on the Cost-effectiveness of Maritime Safety Policy Instruments

Maritime safety is an issue that has gained a lot of attention in the Baltic Sea area due to the dense maritime traffic and transportation of oil in the area. Lots of effort has been paid to enhance maritime safety in the area. The risk exists that excessive legislation and other requirements mean more costs for limited benefit. In order to utilize both public and private resources efficiently, awareness is required of what kind of costs maritime safety policy instruments cause and whether the costs are in relation to benefits. The aim of this report is to present an overview of the cost-effectiveness of maritime safety policy instruments focusing on the cost aspect: what kind of costs maritime safety policy causes, to whom, what affects the cost-effectiveness and how cost-effectiveness is studied. The study is based on a literature review and on the interviews of Finnish maritime experts. The results of this study imply that cost-effectiveness is a complicated issue to evaluate. There are no uniform practices for which costs and benefits should be included in the evaluation and how they should be valued. One of the challenges is how to measure costs and benefits during the course of a longer time period. Often a lack of data erodes the reliability of evaluation. In the prevention of maritime accidents, costs typically include investments in ship structures or equipment, as well as maintenance and labor costs. Also large investments may be justifiable if they respectively provide significant improvements to maritime safety. Measures are cost-effective only if they are implemented properly. Costeffectiveness is decreased if a measure causes overlapping or repetitious work. Costeffectiveness is also decreased if the technology isn’t user-friendly or if it is soon replaced with a new technology or another new appliance. In future studies on the cost-effectiveness of maritime safety policy, it is important to acknowledge the dependency between different policy instruments and the uncertainty of the factors affecting cost-effectiveness. The costs of a single measure are rarely relatively significant and the effect of each measure on safety tends to be positive. The challenge is to rank the measures and to find the most effective combination of different policy instruments. The greatest potential offered for the analysis of cost-effectiveness of individual measures is their implementation in clearly defined risk situations, in which different measures are truly alternative to each other. Overall, maritime safety measures do not seem to be considered burdening for the shipping industry in Finland at the moment. Generally actors in the Finnish shipping industry seem to find maintaining a high safety level important and act accordingly.

New families of highly efficient, halogen-free flame retardants for polypropylene (PP)

The driving forces for current research of flame retardants are increased fire safety in combination with flame retardant formulations that fulfill the criteria of sustainable production and products. In recent years, important questions about the environmental safety of antimony, and in particular, brominated flame retardants have been raised. As a consequence of this, the current doctoral thesis work describes efforts to develop new halogen-free flame retardants that are based on various radical generators and phosphorous compounds. The investigation was first focused on compounds that are capable of generating alkyl radicals in order to study their role on flame retardancy of polypropylene. The family of azoalkanes was selected as the cleanest and most convenient source of free alkyl radicals. Therefore, a number of symmetrical and unsymmetrical azoalkanes of the general formula R-N=N-R’ were prepared. The experimental results show that in the series of different sized azocycloalkanes the flame retardant efficacy decreased in the following order: R = R´= cyclohexyl > cyclopentyl > cyclobutyl > cyclooctanyl > cyclododecanyl. However, in the series of aliphatic azoalkanes compounds, the efficacy decreased as followed: R = R´= n-alkyl > tert-butyl > tert-octyl. The most striking difference in flame retardant efficacy was observed in thick polypropylene plaques of 1 mm, e.g. azocyclohexane (AZO) had a much better flame retardant performance than did the commercial reference FR (Flamestab® NOR116) in thick PP sections. In addition, some of the prepared azoalkane flame retardants e.g. 4’4- bis(cyclohexylazocyclohexyl) methane (BISAZO) exhibited non-burning dripping behavior. Extrusion coating experiments of flame retarded low density polyethylene (LDPE) onto a standard machine finished Kraft paper were carried out in order to investigate the potential of azoalkanes in multilayer facings. The results show that azocyclohexane (AZO) and 4’4-bis (cyclohexylazocyclohexyl) methane (BISAZO) can significantly improve the flame retardant properties of low density polyethylene coated paper already at 0.5 wt.% loadings, provided that the maximum extrusion temperature of 260 oC is not exceeded and coating weight is kept low at 13 g/m2. In addition, various triazene-based flame retardants (RN1=N2-N3R’R’’) were prepared. For example, polypropylene samples containing a very low concentration of only 0.5 wt.% of bis- 4’4’-(3’3’-dimethyltriazene) diphenyl ether and other triazenes passed the DIN 4102-1 test with B2 classification. It is noteworthy that no burning dripping could be detected and the average burning times were very short with exceptionally low weight losses. Therefore, triazene compounds constitute a new and interesting family of radical generators for flame retarding of polymeric materials. The high flame retardant potential of triazenes can be attributed to their ability to generate various types of radicals during their thermal decomposition. According to thermogravimetric analysis/Fourier transform infrared spectroscopy/MS analysis, triazene units are homolytically cleaved into various aminyl, resonance-stabilized aryl radicals, and different CH fragments with simultaneous evolution of elemental nitrogen. Furthermore, the potential of thirteen aliphatic, aromatic, thiuram and heterocyclic substituted organic disulfide derivatives of the general formula R-S-S-R’ as a new group of halogen-free flame retardants for polypropylene films have been investigated. According to the DIN 4102- 1 standard ignitibility test, for the first time it has been demonstrated that many of the disulfides alone can effectively provide flame retardancy and self-extinguishing properties to polypropylene films at already very low concentrations of 0.5 wt.%. For the disulfide family, the highest FR activity was recorded for 5’5’-dithiobis (2-nitrobenzoic acid). Very low values for burning length (53 mm) and burning time (10 s) reflect significantly increased fire retardant performance of this disulfide compared to other compounds in this series as well as to Flamestab® NOR116. Finally, two new, phosphorus-based flame retardants were synthesized: P’P-diphenyl phosphinic hydrazide (PAH) and melamine phenyl phosphonate (MPhP). The DIN 4102-1 test and the more stringent UL94 vertical burning test (UL94 V) were used to assess the formulations ability to extinguish a flame once ignited. A very strong synergistic effect with azoalkanes was found, i.e. in combination with these radical generators even UL94 V0 rate could be obtained.

Failure modes of passive decay heat removing safety systems of modern nuclear power plants

The purpose of this master’s thesis is to gain an understanding of passive safety systems’ role in modern nuclear reactors projects and to research the failure modes of passive decay heat removal safety systems which use phenomenon of natural circulation. Another purpose is to identify the main physical principles and phenomena which are used to establish passive safety tools in nuclear power plants. The work describes passive decay heat removal systems used in AES-2006 project and focuses on the behavior of SPOT PG system. The descriptions of the main large-scale research facilities of the passive safety systems of the AES-2006 power plant are also included. The work contains the calculations of the SPOT PG system, which was modeled with thermal-hydraulic system code TRACE. The dimensions of the calculation model are set according to the dimensions of the real SPOT PG system. In these calculations three parameters are investigated as a function of decay heat power: the pressure of the system, the natural circulation mass flow rate around the closed loop, and the level of liquid in the downcomer. The purpose of the calculations is to test the ability of the SPOT PG system to remove the decay heat from the primary side of the nuclear reactor in case of failure of one, two, or three loops out of four. The calculations show that three loops of the SPOT PG system have adequate capacity to provide the necessary level of safety. In conclusion, the work supports the view that passive systems could be widely spread in modern nuclear projects.

Interprétation des expériences punitives et ses effets sur la délinquance : le cas des infractions routières au Québec.

D'après des études récentes, le lien qui unit les propriétés objectives de la peine (c.-à-d. la sévérité, la certitude et la célérité de la peine) et les propriétés telles que perçues par les délinquants potentiels serait faible, voire inexistant. Par conséquent, les politiques publiques s'appuyant sur le paradigme dissuasif seraient inefficaces pour réduire la criminalité. Toutefois, ces études s'appuient sur un modèle conceptuel limité qui sous-entend que la peine produirait uniquement de la dissuasion. Cette étude vise donc à tester un modèle élargi de prévention générale qui intègre à la fois les notions de dissuasion et de validation normative. D'après ce modèle, l'effet préventif de la peine pourrait s'effectuer à travers les valeurs et les croyances des délinquants potentiels, et ce sans nécessairement modifier leurs perceptions de la peine. Afin de vérifier l'utilité d'un tel modèle, des données ont été colligées à l'aide d'un sondage sur les habitudes de conduite de 448 jeunes conducteurs québécois. Les résultats indiquent que les mécanismes dissuasifs, tels que la certitude perçue d'arrestation et la sévérité perçue des peines, n'ont pas d'effet significatif sur l'intention délictuelle des automobilistes. Toutefois, les valeurs et les croyances de l'automobiliste jouent un rôle essentiel dans la décision d'adopter un comportement routier respectueux des lois. Les automobilistes percevant les problématiques de sécurité routière (c.-à-d. alcool au volant ou vitesse) comme graves auraient moins d'intentions délinquantes. Ces valeurs et ces croyances seraient modulées à la fois par les expériences d'impunité et par le niveau d'exposition aux différentes activités policières sur les routes. Ces résultats suggèrent que l'application des lois peut produire un effet préventif sans nécessairement que des mécanismes dissuasifs en soient responsables.

Street-level labour inspection in China and the implementation of ILO Convention No.155 concerning occupational safety and health

Les relations de travail et d'emploi sont devenues des enjeux importants en Chine. La Chine a ratifié 25 conventions internationales du travail et a travaillé en étroite collaboration avec l'OIT pour améliorer la sécurité et la santé au travail. Malgré ces efforts, la Chine est souvent critiquée pour des violations du travail. Face à ces problèmes, un système législatif d'administration de travail a été développé au niveau national. Mais l’application de ces règlements demeure problématique.. En particulier, les difficultés rencontrées par les inspecteurs du travail dans l'application de ces lois constituent un élément clé du problème. Notre mémoire s'intéresse essentiellement au rôle de l'inspecteur du travail dans l'administration publique de la sécurité du travail en Chine. Ces fonctionnaires jouent un rôle important et peuvent parfois exercer leur discrétion en tant qu'acteurs de première ligne, faisant d'eux de vrais décideurs politiques. Par conséquent, la compréhension de leur rôle et de leur discrétion dans l'application des normes du travail en Chine est cruciale. Notre mémoire est centré sur une étude de cas qualitative d'un bureau d'inspection du travail dans la région de Beijing. Dans le cadre de notre recherche nous avons examiné le rôle des inspecteurs du travail au moyen d’entretiens semi-structurés, d’une recherche documentaire ainsi qu’à l’occasion d’une brève observation des inspecteurs sur lors de la visite d’un lieu de travail. Les résultats démontrent que la définition du pouvoir discrétionnaire des inspecteurs du travail de première ligne en Chine est un enjeu très complexe. L’étude de cas permet cependant d’élaborer un cadre permettant l’identification des facteurs critiques déterminants pour l'évaluation et la compréhension de la nature du pouvoir discrétionnaire de l'inspecteur du travail en application de la loi.

Une analyse procédurale des collisions mortelles chez les conducteurs de 16-29 ans et implications en termes de prévention : une analyse des scripts

Context and objectives. While 11% of all drivers are aged between 16 and 24, they represent 20% of all fatally injured drivers on the road network of the Province of Quebec. In collaboration with the Sûreté du Québec (SQ), this study seeks to: (1) offer a detailed description of the process (script) leading to fatal collisions involving young drivers; and (2) to recommend prevention measures. Methodology. The script perspective was used to relate the process leading to a fatal collision. The script perspective accounts for all steps that lead to the collision by focusing on: (1) all parties (the driver, friends, parents) and their actions; (2) contexts; and (3) environments. Data were collected from collision and investigation files (n=179). Descriptive and comparative analyses were then conducted to construct the script(s). Results. Results show that fatal collision scripts for 16-29 are different from scripts involving drivers of other age categories (30-59 year-old and 60 year-old and over). The typical script involves a young driver using his car to take part in leisure or festive activities. The latest often occur in a private residence, a bar or a restaurant. On site, young drivers frequently consume psychoactive substances (between 21 and 63.5% of them according to the scene of the script) and are accompanied by friends (between 18.4 and 73.9% according to the scene of the script). Friends often encourage drivers to have alcohol and/or drugs, and to adopt reckless behaviours (speeding and drinking-and-driving are respectively involved in 29.9 and 28.6% of fatal collisions). Conclusion and implications for prevention. Results suggest that fatal collisions involving young drivers could be avoided by encouraging prevention measures aimed at: (1) separating drinking and driving; (2) limiting access to alcohol and peer pressure; (3) raising awareness among potential guardians (e.g. responsible waiters, friends); and (4) increasing arrest risk.

Lower Cortisol Activity is Associated with First-Time Driving while Impaired

Driving while impaired (DWI) is a grave and persistent high-risk behavior. Previous work demonstrated that DWI recidivists had attenuated cortisol reactivity compared to non-DWI drivers. This suggests that cortisol is a neurobiological marker of high-risk driving. The present study tested the hypothesis that this initial finding would extend to first-time DWI (fDWI) offenders compared to non-DWI drivers. Male fDWI offenders (n = 139) and non-DWI drivers (n = 31) were exposed to a stress task, and their salivary cortisol activity (total output and reactivity) was measured. Participants also completed questionnaires on sensation seeking, impulsivity, substance use, and engagement in risky and criminal behaviors. As hypothesized, fDWI offenders, compared to non-DWI drivers, had lower cortisol reactivity; fDWI offenders also showed lower total output. In addition, cortisol activity was the most important predictor of group membership, after accounting for alcohol misuse patterns and consequences and other personality and problem behavior characteristics. The findings indicate that attenuated cortisol activity is an independent factor associated with DWI offending risk at an earlier stage in the DWI trajectory than previously detected.

STUDY OF INFLUENCE OF SAFETY ENGINEERING AND MANAGEMENT PRACTICES IN SELECTED INDUSTRIES IN KERALA

In the twentieth century, as technology grew with it. This resulted in collective efforts and thinking in the direction of controlling work related hazards and accidents. Thus, safety management developed and became an important part of industrial management. While considerable research has been reported on the topic of safety management in industries from various parts of the world, there is scarcity of literature from India. It is logical to think that a clear understanding of the critical safety management practices and their relationships with accident rates and management system certifications would help in the development and implementation of safety management systems. In the first phase of research, a set of six critical safety management practices has been identified based on a thorough review of the prescriptive, practitioner, conceptual and empirical literature. An instrument for measuring the level of practice of these safety conduction a survey using questionnaire in chemical/process industry. The instrument has been empirically validated using Confirmatory Factor Analysis (CFA) approach. As the second step. Predictive validity of safety management practices and the relationship between safety management practices and self-reported accident rates and management system certifications have been investigated using ANOVA. Results of the ANOVA tests show that there is significant difference in the identified safety management practices and the determinants of safety performance have been investigated using Multiple Regression Analysis. The inter-relationships between safety management practices, determinants of safety performance and components of safety performance have been investigated with the help of structural equation modeling. Further investigations into engineering and construction industries reveal that safety climate factors are not stable across industries. However, some factors are found to be common in industries irrespective of the type of industry. This study identifies the critical safety management practices in major accident hazard chemical/process industry from the perspective of employees and the findings empirically support the necessity for obtaining safety specific management system certifications

An Analysis of Work Related Stress Factor in Selected Industries in Kerala ,India

Occupational stress is becoming a major issue in both corporate and social agenda .In industrialized countries, there have been quite dramatic changes in the conditions at work, during the last decade ,caused by economic, social and technical development. As a consequence, the people today at work are exposed to high quantitative and qualitative demands as well as hard competition caused by global economy. A recent report says that ailments due to work related stress is likely to cost India’s exchequer around 72000 crores between 2009 and 2015. Though India is a fast developing country, it is yet to create facilities to mitigate the adverse effects of work stress, more over only little efforts have been made to assess the work related stress.In the absence of well defined standards to assess the work related stress in India, an attempt is made in this direction to develop the factors for the evaluation of work stress. Accordingly, with the help of existing literature and in consultation with the safety experts, seven factors for the evaluation of work stress is developed. An instrument ( Questionnaire) was developed using these seven factors for the evaluation of work stress .The validity , and unidimensionality of the questionnaire was ensured by confirmatory factor analysis. The reliability of the questionnaire was ensured before administration. While analyzing the relation ship between the variables, it is noted that no relationship exists between them, and hence the above factors are treated as independent factors/ variables for the purpose of research .Initially five profit making manufacturing industries, under public sector in the state of Kerala, were selected for the study. The influence of factors responsible for work stress is analyzed in these industries. These industries were classified in to two types, namely chemical and heavy engineering ,based on the product manufactured and work environment and the analysis is further carried out for these two categories.The variation of work stress with different age , designation and experience of the employees are analyzed by means of one-way ANOVA. Further three different type of modelling of work stress, namely factor modelling, structural equation modelling and multinomial logistic regression modelling was done to analyze the association of factors responsible for work stress. All these models are found equally good in predicting the work stress.The present study indicates that work stress exists among the employees in public sector industries in Kerala. Employees belonging to age group 40-45yrs and experience groups 15-20yrs had relatively higher work demand ,low job control, and low support at work. Low job control was noted among lower designation levels, particularly at the worker level in these industries. Hence the instrument developed using the seven factors namely demand, control, manager support, peer support, relationship, role and change can be effectively used for the evaluation of work stress in industries.

Modeling Of Work-Related Musculoskeletal Disorders In Chemical Process Industry In India

In this modern complex world, stress at work is found to be increasingly a common feature in day to day life. For the same reason, job stress is one of the active areas in occupational health and safety research for over last four decades and is continuing to attract researchers in academia and industry. Job stress in process industries is of concern due to its influence on process safety, and worker‘s safety and health. Safety in process (chemical and nuclear material) industry is of paramount importance, especially in a thickly populated country like India. Stress at job is the main vector in inducing work related musculoskeletal disorders which in turn can affect the worker health and safety in process industries. In view of the above, the process industries should try to minimize the job stress in workers to ensure a safe and healthy working climate for the industry and the worker. This research is mainly aimed at assessing the influence of job stress in inducing work related musculoskeletal disorders in chemical process industries in India