Dual Z-source inverter with three-level reduced common-mode switching

This paper presents the design of a dual Z-source inverter that can be used with either a single dc source or two isolated dc sources. Unlike traditional inverters, the integration of a properly designed Z-source network and semiconductor switches to the proposed dual inverter allows buck-boost power conversion to be performed over a wide modulation range, with three-level output waveforms generated. The connection of an additional transformer to the inverter ac output also allows all generic wye-or delta-connected loads with three-wire or four-wire configuration to be supplied by the inverter. Modulationwise, the dual inverter can be controlled using a carefully designed carrier-based pulsewidth-modulation (PWM) scheme that will always ensure balanced voltage boosting of the Z-source network while simultaneously achieving reduced common-mode switching. Because of the omission of dead-time delays in the dual-inverter PWM scheme, its switched common-mode voltage can be completely eliminated, unlike in traditional inverters, where narrow common-mode spikes are still generated. Under semiconductor failure conditions, the presented PWM schemes can easily be modified to allow the inverter to operate without interruption, and for cases where two isolated sources are used, zero common-mode voltage can still be ensured. These theoretical findings, together with the inverter practicality, have been confirmed in simulations both using PSIM with Matlab/Simulink coupler and experimentally using a laboratory-implemented inverter prototype.

Phase Relations in the System CaO-Fe2O3-Y2O3 at 1273 K and Compatibility Between Y1-xCaxFeO3-0.5x and Stabilized Zirconia

Phase relations in the system CaO-Fe2O3-Y2O3 in air (P-O2/P-o = 0.21) were explored by equilibrating samples representing eleven compositions in the ternary at 1273 K, followed by quenching to room temperature and phase identification using XRD. Limited mutual solubility was observed between YFeO3 and Ca2Fe2O5. No quaternary oxide was identified. An isothermal section of the phase diagram at 1273 K was constructed from the results. Five three-phase regions and four extended two-phase regions were observed. The extended two-phase regions arise from the limited solid solutions based on the ternary oxides YFeO3 and Ca2Fe2O5. Activities of CaO, Fe2O3 and Y2O3 in the three-phase fields were computed using recently measured thermodynamic data on the ternary oxides. The experimental phase diagram is consistent with thermodynamic data. The computed activities of CaO indicate that compositions of CaO-doped YFeO3 exhibiting good electrical conductivity are not compatible with zirconia-based electrolytes; CaO will react with ZrO2 to form CaZrO3.

Phase reconstruction from three interferograms based on integral of phase gradient

A novel algorithm of phase reconstruction based on the integral of phase gradient is presented. The algorithm directly derives two real-valued partial derivatives from three phase-shifted interferograms. Through integrating the phase derivatives, the desired phase is reconstructed. During the phase reconstruction process, there is no need for an extra rewrapping manipulation to ensure values of the phase derivatives lie in the interval [-pi, pi] as before, thus this algorithm can prevent error or distortion brought about by the phase unwrapping operation. Additionally, this algorithm is fast and easy to implement, and insensitive to the nonuniformity of the intensity distribution of the interferogram. The feasibility of the algorithm is demonstrated by both computer simulation and experiment.

Estudos teóricos e experimentais da operação conjunta de um supressor eletromagnético e de um filtro ativo de potência

Pós-graduação em Engenharia Elétrica - FEIS

A converter compensator for power factor control in 3-phase induction machines

The advent of the harmonic neutralised shunt Converter Compensator as a practical means of reactive power compensation in power transmission systems has cleared ground for wider application of this type of equipment. An experimental 24-pulse voltage sourced convector has been successfully applied in controlling the terminal power factor of a 1.5kW, 240V three phase cage rotor induction motor, whose winding has been used in place of the usual phase shifting transformers. To achieve this, modifications have been made to the conventional stator winding of the induction machine. These include an unconventional phase spread and facilitation of compensator connections to selected tapping points between stator coils to give a three phase winding with a twelve phase connection to the twenty four pulse converter. Theoretical and experimental assessments of the impact of these modifications and attachment of the compensator have shown that there is a slight reduction in the torque developed at a given slip and in the combined system efficiency. There is also an increase in the noise level, also a consequence of the harmonics. The stator leakage inductance gave inadequate coupling reactance between the converter and the effective voltage source, necessitating the use of external inductors in each of the twelve phases. The terminal power factor is fully controllable when the induction machine is used either as a motor or as a generator.

The nature and extent of policing alcohol related crime and reducing violence in and around late night entertainment areas

The misuse of alcohol is well documented in Australia and has been associated with disorders and harms that often require police attention. The extent of alcohol-related incidents requiring police attention has been recorded as substantial in some Australian cities (Arro, Crook, & Fenton, 1992; Davey & French, 1995; Ireland & Thommeny, 1993). A significant proportion of harmful drinking occurs in and around licensed premises (Jochelson, 1997; Stockwell, Masters, Phillips, Daly, Gahegan, Midford, & Philp, 1998; Borges, Cherpitel, & Rosovsky, 1998) and most of these incidents are not reported to police (Bryant & Williams, 2000; Lister, Hobbs, Hall, & Winlow, 2000). Alcohol-related incidents have also been found to be concentrated in certain places at certain times (Jochelson, 1997) and therefore manipulating the context in which these incidents occur may provide a means to prevent and reduce the harm associated with alcohol misuse. One of the major objectives of the present program of research was to investigate the occurrence and resource impact of alcohol-related incidents on operational (general duties) policing across a large geographical area. A second objective of the thesis was to examine the characteristics and temporal/spatial dynamics of police attended alcohol incidents in the context of Place Based theories of crime. It was envisaged that this approach would reveal the patterns of the most prevalent offences and demonstrate the relevance of Place Based theories of crime to understanding these patterns. In addition, the role of alcohol, time and place were also explored in order to examine the association between non criminal traffic offences and other types of criminal offences. A final objective of the thesis was to examine the impact of a situational crime prevention strategy that had been initiated to reduce the violence and disorder associated with late-night liquor trading premises. The program of research in this doctorate thesis has been undertaken through the presentation of published papers. The research was conducted in three stages which produced six manuscripts, five of which were submitted to peer reviewed journals and one that was published in a peer reviewed conference proceedings. Stage One included two studies (Studies 1 & 2) both of which involved a cross sectional approach to examine the prevalence and characteristics of alcohol-related incidents requiring police attendance across three large geographical areas that included metropolitan cities, provincial regions and rural areas. Stage Two of the program of research also comprised two cross sectional quantitative studies (Studies 3 & 4) that investigated the temporal and spatial dynamics of the major offence categories attended by operational police in a specific Police District (Gold Coast). Stage Three of the program of research involved two studies (Studies 5 & 6) that assessed the effectiveness of a situational crime prevention strategy. The studies employed a pre-post design to assess the impact on crime, disorder and violence by preventing patrons from entering late-night liquor trading premises between 3 a.m. and 5 a.m. (lockout policy). Although Study Five was solely quantitative in nature, Study Six included both quantitative and qualitative aspects. The approach adopted in Study Six, therefore facilitated not only a quantative comparison of the impact of the lockout policy on different policing areas, but also enabled the processes related to the implementation of the lockout policy to be examined. The thesis reports a program of research involving a common data collection method which then involved a series of studies being conducted to explore different aspects of the data. The data was collected from three sources. Firstly a pilot phase was undertaken to provide participants with training. Secondly a main study period was undertaken immediately following the pilot phase. The first and second sources of data were collected between 29th March 2004 and 2nd May 2004. Thirdly, additional data was collected between the 1st April 2005 and 31st May 2005. Participants in the current program of research were first response operational police officers who completed a modified activity log over a 9 week period (4 week pilot phase & 5 week survey study phase), identifying the type, prevalence and characteristics of alcohol-related incidents that were attended. During the study period police officers attended 31,090 alcohol-related incidents. Studies One and Two revealed that a substantial proportion of current police work involves attendance at alcohol-related incidents (i.e., 25% largely involving young males aged between 17 and 24 years). The most common incidents police attended were vehicle and/or traffic matters, disturbances and offences against property. The major category of offences most likely to involve alcohol included vehicle/traffic matters, disturbances and offences against the person (e.g., common & serious assaults). These events were most likely to occur in the late evenings and early hours of the morning on the weekends, and importantly, usually took longer for police to complete than non alcohol-related incidents. The findings in Studies Three and Four suggest that serious traffic offences, disturbances and offences against the person share similar characteristics and occur in concentrated places at similar times. In addition, it was found that time, place and incident type all have an influence on whether an incident attended by a police officer is alcohol-related. Alcohol-related incidents are more likely to occur in particular locations in the late evenings and early mornings on the weekends. In particular, there was a strong association between the occurrence of alcohol-related disturbances and alcohol-related serious traffic offences in regards to place and time. In general, stealing and property offences were not alcohol-related and occurred in daylight hours during weekdays. The results of Studies Five and Six were mixed. A number of alcohol-related offences requiring police attention were significantly reduced for some policing areas and for some types of offences following the implementation of the lockout policy. However, in some locations the lockout policy appeared to have a negative or minimal impact. Interviews with licensees revealed that although all were initially opposed to the lockout policy as they believed it would have a negative impact on business, most perceived some benefits from its introduction. Some of the benefits included, improved patron safety and the development of better business strategies to increase patron numbers. In conclusion, the overall findings of the six studies highlight the pervasive nature of alcohol across a range of criminal incidents, demonstrating the tremendous impact alcohol-related incidents have on police. The findings also demonstrate the importance of time and place in predicting the occurrence of alcohol-related offences. Although this program of research did not set out to test Place Based theories of crime, these theories were used to inform the interpretation of findings. The findings in the current research program provide evidence for the relevance of Place Based theories of crime to understanding the factors contributing to violence and disorder, and designing relevant crime prevention strategies. For instance, the results in Studies Five and Six provide supportive evidence that this novel lockout initiative can be beneficial for public safety by reducing some types of offences in particular areas in and around late-night liquor trading premises. Finally, intelligent-led policing initiatives based on problem oriented policing, such as the lockout policy examined in this thesis, have potential as a major crime prevention technique to reduce specific types of alcohol-related offences.

Labour rights as human rights : workers' safety at work in Australian-based supply chains

The increase of buyer-driven supply chains, outsourcing and other forms of non-traditional employment has resulted in challenges for labour market regulation. One business model which has created substantial regulatory challenges is supply chains. The supply chain model involves retailers purchasing products from brand corporations who then outsource the manufacturing of the work to traders who contract with factories or outworkers who actually manufacture the clothing and textiles. This business model results in time and cost pressures being pushed down the supply chain which has resulted in sweatshops where workers systematically have their labour rights violated. Literally millions of workers work in dangerous workplaces where thousands are killed or permanently disabled every year. This thesis has analysed possible regulatory responses to provide workers a right to safety and health in supply chains which provide products for Australian retailers. This thesis will use a human rights standard to determine whether Australia is discharging its human rights obligations in its approach to combating domestic and foreign labour abuses. It is beyond this thesis to analyse Occupational Health and Safety (OHS) laws in every jurisdiction. Accordingly, this thesis will focus upon Australian domestic laws and laws in one of Australia’s major trading partners, the Peoples’ Republic of China (China). It is hypothesised that Australia is currently breaching its human rights obligations through failing to adequately regulate employees’ safety at work in Australian-based supply chains. To prove this hypothesis, this thesis will adopt a three- phase approach to analysing Australia’s regulatory responses. Phase 1 will identify the standard by which Australia’s regulatory approach to employees’ health and safety in supply chains can be judged. This phase will focus on analysing how workers’ rights to safety as a human right imposes a moral obligation on Australia to take reasonablely practicable steps regulate Australian-based supply chains. This will form a human rights standard against which Australia’s conduct can be judged. Phase 2 focuses upon the current regulatory environment. If existing regulatory vehicles adequately protect the health and safety of employees, then Australia will have discharged its obligations through simply maintaining the status quo. Australia currently regulates OHS through a combination of ‘hard law’ and ‘soft law’ regulatory vehicles. The first part of phase 2 analyses the effectiveness of traditional OHS laws in Australia and in China. The final part of phase 2 then analyses the effectiveness of the major soft law vehicle ‘Corporate Social Responsibility’ (CSR). The fact that employees are working in unsafe working conditions does not mean Australia is breaching its human rights obligations. Australia is only required to take reasonably practicable steps to ensure human rights are realized. Phase 3 identifies four regulatory vehicles to determine whether they would assist Australia in discharging its human rights obligations. Phase 3 then analyses whether Australia could unilaterally introduce supply chain regulation to regulate domestic and extraterritorial supply chains. Phase 3 also analyses three public international law regulatory vehicles. This chapter considers the ability of the United Nations Global Compact, the ILO’s Better Factory Project and a bilateral agreement to improve the detection and enforcement of workers’ right to safety and health.

Free surface flow past topography : a beyond-all-orders approach

The problem of steady subcritical free surface flow past a submerged inclined step is considered. The asymptotic limit of small Froude number is treated, with particular emphasis on the effect that changing the angle of the step face has on the surface waves. As demonstrated by Chapman & Vanden-Broeck (2006), the divergence of a power series expansion in powers of the square of the Froude number is caused by singularities in the analytic continuation of the free surface; for an inclined step, these singularities may correspond to either the corners or stagnation points of the step, or both, depending on the angle of incline. Stokes lines emanate from these singularities, and exponentially small waves are switched on at the point the Stokes lines intersect with the free surface. Our results suggest that for a certain range of step angles, two wavetrains are switched on, but the exponentially subdominant one is switched on first, leading to an intermediate wavetrain not previously noted. We extend these ideas to the problem of flow over a submerged bump or trench, again with inclined sides. This time there may be two, three or four active Stokes lines, depending on the inclination angles. We demonstrate how to construct a base topography such that wave contributions from separate Stokes lines are of equal magnitude but opposite phase, thus cancelling out. Our asymptotic results are complemented by numerical solutions to the fully nonlinear equations.

Harmonic elimination technique for a single-phase multilevel converter with unequal DC link voltage levels

Multilevel converters, because of the benefits they attract in generating high quality output voltage, are used in several applications. Various modulation and control techniques are introduced by several researchers to control the output voltage of the multilevel converters like space vector modulation and harmonic elimination (HE) methods. Multilevel converters may have a DC link with equal or unequal DC voltages. In this study a new HE technique based on the HE method is proposed for multilevel converters with unequal DC link voltage. The DC link voltage levels are considered as additional variables for the HE method and the voltage levels are defined based on the HE results. Increasing the number of voltage levels can reduce lower order harmonic content because of the fact that more variables are created. In comparison to previous methods, this new technique has a positive effect on the output voltage quality by reducing its total harmonic distortion, which must take into consideration for some applications such as uninterruptable power supply, motor drive systems and piezoelectric transducer excitation. In order to verify the proposed modulation technique, MATLAB simulations and experimental tests are carried out for a single-phase four-level diode-clamped converter.

The University of Queensland St Lucia campus 1.22 MW photovoltaic array

At the time of its official opening on 15 July 2011, The University of Queensland 1.22 MW array was the largest flat-panel PhotoVoltaic (PV) array in Australia. This PV array consists of over 5000 Trina Solar 240 Wp polycrystalline silicon PV modules installed across four rooftops at the St Lucia campus. Grid connection was achieved with 85 12.5 kW three phase and four 5 kW single phase grid connect inverters manufactured by Power-One. The site also includes one 8.4 kWp SolFocus concentrating solar 2 axis tracking PV array. Site wide monitoring and data logging of all DC, AC and environmental quantities will allow this array to be a rich source of research data. The site will also include a 200 kW 400 kWh zinc bromine energy storage system by Redflow, and associated power quality metering and monitoring. This paper presents highlights of the project feasibility study which included a site survey, shading analysis, and technology and triple bottom line assessment. A detailed description of the final technical implementation including discussion of alterative options considered is given. Finally, example initial data showing yield, trends and early example experimental results are presented.

Voltage unbalance reduction in low voltage feeders by dynamic switching of residential customers among three phases

Low voltage distribution feeders with large numbers of single phase residential loads experience severe current unbalance that often causes voltage unbalance problems. The addition of intermittent generation and new loads in the form of roof top photovoltaic generation and electric vehicles makes these problems even more acute. In this paper, an intelligent dynamic residential load transfer scheme is proposed. Residential loads can be transferred from one phase to another phase to minimize the voltage unbalance along the feeder. Each house is supplied through a static transfer switch with three-phase input and single-phase output connection. The main controller, installed at the transformer will observe the power consumption in each load and determine which house(s) should be transferred from one phase to another in order to keep the voltage unbalance in the feeder at a minimum. The efficacy of the proposed load transfer scheme is verified through MATLAB and PSCAD/EMTDC simulations.

Thermodynamic properties of Pb2PtO4 and PbPt2O4 and phase equilibria in the system Pb–Pt–O

The compounds Pb2PtO4 and PbPt2O4 were synthesized from an intimate mixture of yellow PbO and Pt metal powders by heating under pure oxygen gas at 973 K for periods up to 600 ks with intermediate grinding and recompacting. Both compounds were found to decompose on heating in pure oxygen to PbO and Pt, apparently in conflict with the requirements for equilibrium phase relations in the ternary system Pb–Pt–O. The oxygen chemical potential corresponding to the three-phase mixtures, Pb2PtO4 + PbO + Pt and PbPt2O4 + PbO + Pt were measured as a function of temperature using solid-state electrochemical cells incorporating yttria-stabilized zirconia as the solid electrolyte and pure oxygen gas at 0.1 MPa pressure as the reference electrode. The standard Gibbs free energies of formation of the ternary oxides were derived from the measurements. Analysis of the results indicated that the equilibrium involving three condensed phases Pb2PtO4 + PbO + Pt is metastable. Under equilibrium conditions, Pb2PtO4 should have decomposed to a mixture of PbO and PbPt2O4. Measurement of the oxygen potential corresponding to this equilibrium decomposition as a function of temperature indicated that decomposition temperature in pure oxygen is 1014(±2) K. This was further confirmed by direct determination of phase relations in the ternary Pb–Pt–O by equilibrating several compositions at 1023 K for periods up to 850 ks and phase identification of quenched samples using X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS). Only one ternary oxide PbPt2O4 was stable at 1023 K under equilibrium conditions. Alloys and intermetallic compounds along the Pb–Pt binary were in equilibrium with PbO.

Cutaneous porphyrias : Clinical and histopathological study

The prevalence of variegate porphyria (VP) (2.1:100 000, in 2006 n=108) was higher in Finland than elsewhere in European countries due to a founder effect (R152C). The incidence of VP was estimated at 0.2:1 000 000 based on the number of new symptomatic patients yearly. The prevalence of porphyria cutanea tarda (PCT) was 1.2:100 000 (in 2006 n=63), which is only one fourth of the numbers reported from other European countries. The estimated incidence of PCT was 0.5:1 000 000. Based on measurements of the uroporphyrinogen decarboxylase activity in erythrocytes, the proportion of familial PCT was 49% of the cases. The prevalence of erythropoietic protoporphyria (EPP) was at 0.8:100 000 (in 2006 n=39) including asymptomatic carriers of a mutation in the ferrochelatase (FECH) gene. The incidence of EPP was estimated at 0.1:1 000 000. After 1980 the penetrance was 37% among patients with VP. Of the mutation carriers (n=57) 30% manifested with skin symptoms. Frequency of skin symptom as only clinical sign was stable before or after 1980 (22% vs. 21%), but acute attacks became infrequent (29% vs. 7%). Of the symptomatic patients 30% had both acute attacks and skin symptoms and 80% had skin symptoms. Fragility (95%) and blistering (46%) of the skin in the backs of the hands were the most common skin symptoms. Transient correction of porphyrin metabolism using eight haem arginate infusions within five weeks had no effect on the skin symptoms in three of four patients with VP. In one case skin symptoms disappeared transiently. One patient with homozygous VP had severe photosensitivity since birth. Sensory polyneuropathy, glaucoma and renal failure developed during the 25-year follow-up without the presence of acute attacks. The I12T mutation was detected in both of his alleles in the protoporphyrinogen oxidase gene. Lack of skin symptoms and infrequency of acute attacks (1/9) in the patients with I12T mutation at the heterozygous stage indicate a mild phenotype (the penetrance 11%). Four mutations (751delGAGAA, 1122delT, C286T, C343T) in the FECH gene were characterised in four of 15 families with EPP. Burning pain (96%) and swelling (92%) of the sun-exposed skin were the major skin symptoms. Hepatopathy appeared in one of 25 symptomatic patients (4%). Clinical manifestations and associated factors of PCT were similar in the sporadic and familial types of PCT. The majority of the patients with PCT had one to three precipitating factors: alcohol intake (78%), mutations in hemochromatosis associated gene (50%), use of oestrogen (25% of women) and hepatitis B or C infections (25 %). Fatty liver disease (67%) and siderosis (67%) were commonly found in their liver biopsies. The major histopathological change of the sun-exposed skin in the patients with VP (n=20), EPP (n=8) and PCT (n=5) was thickening of the vessel walls of the upper dermis suggesting that the vessel wall is the primary site of the phototoxic reaction in each type of porphyria. The fine structure of the vessel walls was similar in VP, EPP and PCT consisting of the multilayered basement membrane and excess of finely granular substance between the layers which were surrounded by the band of homogenous material. EPP was characterised by amorphous perivascular deposits extending also to the extravascular space. In direct immunofluorescence study homogenous IgG deposits in the vessel walls of the upper dermis of the sun-exposed skin were demonstrated in each type of porphyria. In EPP the excess material around vessel walls consisted of other proteins such as serum amyloid protein, and kappa and lambda light chains in addition to the basement membrane constituents such as collagen IV and laminin. These results suggest that the alterations of the vessel walls are a consequence of the repeated damage and the repairing process in the vessel wall. The microscopic alterations could be demonstrated even in the normal looking but sun-exposed skin of the patients with EPP during the symptom-free phase suggesting that vascular change can be chronic. The stability of vascular changes in the patients with PCT after treatment indicates that circulating porphyrins are not important for the maintenance of the changes.

Direct torque control schemes for split-phase induction machine

In this paper, direct torque control (DTC) algorithms for a split-phase induction machine (SPIM) are established. An SPIM has two sets of three-phase stator windings, with a shift of thirty electrical degrees between them. The significant contributions of this paper are: 1) two new methods of DTC technique for an SPIM are developed, called Resultant Flux Control Method and Individual Flux Control Method and 2) advantages and disadvantages of both methods are discussed. High torque ripple is a disadvantage for three-phase DTC. It is found that torque ripple in an SPIM can be significantly reduced without increasing the switching frequency.

Towards understanding the unusual Indian monsoon in 2009

The Indian summer monsoon season of 2009 commenced with a massive deficit in all-India rainfall of 48% of the average rainfall in June. The all-India rainfall in July was close to the normal but that in August was deficit by 27%. In this paper, we first focus on June 2009, elucidating the special features and attempting to identify the factors that could have led to the large deficit in rainfall. In June 2009, the phase of the two important modes, viz., El Nino and Southern Oscillation (ENSO) and the equatorial Indian Ocean Oscillation (EQUINOO) was unfavourable. Also, the eastern equatorial Indian Ocean (EEIO) was warmer than in other years and much warmer than the Bay. In almost all the years, the opposite is true, i.e., the Bay is warmer than EEIO in June. It appears that this SST gradient gave an edge to the tropical convergence zone over the eastern equatorial Indian Ocean, in competition with the organized convection over the Bay. Thus, convection was not sustained for more than three or four days over the Bay and no northward propagations occurred. We suggest that the reversal of the sea surface temperature (SST) gradient between the Bay of Bengal and EEIO, played a critical role in the rainfall deficit over the Bay and hence the Indian region. We also suggest that suppression of convection over EEIO in association with the El Nino led to a positive phase of EQUINOO in July and hence revival of the monsoon despite the El Nino. It appears that the transition to a negative phase of EQUINOO in August and the associated large deficit in monsoon rainfall can also be attributed to the El Nino.