Studies on the Quality of Rainwater at Various Land Use Locations and Variations by Interaction with Domestic Rainwater Harvesting Systems

The present study focused on the quality of rainwater at various land use locations and its variations on interaction with various domestic rainwater harvesting systems.Sampling sites were selected based upon the land use pattern of the locations and were classified as rural, urban, industrial and sub urban. Rainwater samples were collected from the south west monsoon of May 2007 to north east monsoon of October 2008, from four sampling sites namely Kothamangalam, Emakulam, Eloor and Kalamassery, in Ernakulam district of the State of Kerala, which characterized typical rural, urban, industrial and suburban locations respectively. Rain water samples at various stages of harvesting were also collected. The samples were analyzed according to standard procedures and their physico-chemical and microbiological parameters were determined. The variations of the chemical composition of the rainwater collected were studied using statistical methods. It was observed that 17.5%, 30%, 45.8% and 12.1% of rainwater samples collected at rural, urban, industrial and suburban locations respectively had pH less than 5.6, which is considered as the pH of cloud water at equilibrium with atmospheric CO,.Nearly 46% of the rainwater samples were in acidic range in the industrial location while it was only 17% in the rural location. Multivariate statistical analysls was done using Principal Component Analysis, and the sources that inf1uence the composition of rainwater at each locations were identified .which clearly indicated that the quality of rain water is site specific and represents the atmospheric characteristics of the free fall The quality of harvested rainwater showed significant variations at different stages of harvesting due to deposition of dust from the roof catchment surface, leaching of cement constituents etc. Except the micro biological quality, the harvested rainwater satisfied the Indian Standard guide lines for drinking water. Studies conducted on the leaching of cement constituents in water concluded that tanks made with ordinary portland cement and portland pozzolana cement could be safely used for storage of rain water.

Recycling urban waste as possible use for rooftop vegetable garden

Urban authorities in Europe are confronted with increasing demands by urban dwellers for allotment gardens, but vacant urban soil tends to be scarce and/or polluted by past industrial activities. A possible solution for local authorities could therefore be to promote rooftop gardening. However little technical information exists on certain forms of rooftop urban agriculture, called Z-Farming. In 2012, a pilot experiment was run in Paris (France). Simple and cheap systems of rooftop gardening were tested on a rooftop using as crop substrates only local urban organic waste so as to contribute to the urban metabolism. Production levels and heavy metal contents in cropping substrates and edible vegetables were measured. Available results show (i) high levels of crop production with limited inputs compared to land professional gardening, (ii) low levels of heavy metal pollutants in the edible parts of the crops, especially for Cd and Pb with respect to EU norms for vegetables and (iii) positive influence on yields on organizing the substrate in layers and enhancing the biological activity through earthworm inoculation. These encouraging results allow us to consider that rooftop gardening is feasible and seem to have a great potential to improve urban resiliency. It will nevertheless be necessary to identify more precisely the types of roof that can be used and to assess more fully the generic result of the low level of pollution, as well as the global sustainability of these cropping systems.

Planning Urban Food Production into Today's Cities

If cities are to become more sustainable and resilient to change it is likely that they will have to engage with food at increasingly localised levels, in order to reduce their dependency on global systems. With 87 percent of people in developed regions estimated to be living in cities by 2050 it can be assumed that the majority of this localised production will occur in and around cities. As part of a 12 month engagement, Queen’s University Belfast designed and implemented an elevated aquaponic food system spanning the top internal floor and exterior roof space of a disused mill in Manchester, England. The experimental aquaponic system was developed to explore the possibilities and difficulties associated with integrating food production with existing buildings. This paper utilises empirical research regarding crop growth from the elevated aquaponic system and extrapolates the findings across a whole city. The resulting research enables the agricultural productive capacity of today’s cities to be estimated and a framework of implementation to be proposed.

Selección del país objetivo para un plan de internacionalización de teja de arcilla desde Colombia 2013

A partir del conocimiento que se posee referente al desarrollo de las ladrilleras del sector de Nemocón y las herramientas y disciplinas aplicables al estudio de un plan de internacionalización, se determina desarrollar el siguiente proceso. En primer lugar, a partir de la necesidad de diagnosticar un análisis del sector ladrillero en Nemocón Cundinamarca, se hace indispensable utilizar herramientas de la línea de estrategia. Se requiere de un estudio matricial del comportamiento del sector con su respectivo análisis y para generar un mayor soporte técnico al análisis del sector, se requiere de un estudio de planeación estratégica por escenarios el cual proveerá a la investigación de diversas alternativas en la selección de variables fundamentales del sistema. Acerca del estudio de los mercados tanto nacional como internacional, se dispondrá de las habilidades básicas de la línea de mercadeo. Es importante que a partir del análisis del sector y de la obtención de algunas variables importantes, se indague a profundidad acerca de las variables más importantes para el desarrollo de una matriz de mercados. La idea de la aplicación de esta matriz, es generar unos filtros de países seleccionados a partir de variables anteriormente especificadas con el fin de determinar un único mercado que será el objetivo para el plan de internacionalización. Sobre el país seleccionado se aplica un estudio de mercado y un estudio de viabilidad financiera bajo los cuales se obtienen las conclusiones del plan de internacionalización, su viabilidad y sus recomendaciones.

Medidas de intervención para promoción de conductas saludables y prevención de riesgos laborales relacionados con accidentalidad y enfermedad laboral en trabajadores de minas de Carbón

Colombia en su legislación normatiza el sector de la minería de carbón, sin embargo se considera que las estrategias no han sido suficientes para la identificación, prevención y control de la accidentalidad y enfermedad laboral. Durante el año 2013 el índice de fatalidad fue de 1,59. Estadísticas del año 2004 evidencian que las neumoconiosis fueron las mayores causas de invalidez de origen profesional. Objetivo: Categorizar actividades de intervención en promoción y prevención de accidentalidad y enfermedad laboral en trabajadores de la minería de carbón. Metodología: Se realizó una revisión de literatura sobre minería de carbón y salud la cual fue obtenida de las bases de datos PUBMED, Sciendirect, VHL, SINAB por literatura publicada sin límites de año, en idioma inglés, español o portugués. Para la búsqueda se utilizaron términos en lenguaje controlado (términos MESH), revisión por pares de títulos y resúmenes. Las publicaciones fueron seleccionadas para revisión de texto completo bajo criterios de inclusión y exclusión. Los códigos contemplados para esta revisión fueron: a) país donde la intervención se llevó a cabo, b) salud ocupacional, c) prevención de accidentalidad, d) programas de promoción, e) tecnologías, f) resultados obtenidos. Resultados: Del total de 2500 artículos seleccionados por los autores principales se realizó la revisión de los primeros 300 artículos, 32 hacen referencia al tema de salud ocupacional y minería de carbón, 10 contienen intervenciones consideradas de relevancia para esta revisión bibliográfica. Se presentan intervenciones estadísticamente significativas (p<0.05) y que han demostrado ser de impacto positivo en la minería de carbón en promoción y prevención de accidentalidad y enfermedad ocupacional. Conclusiones: Se identificaron las siguientes cuatro tipos de intervención: 1) las de carácter educativo que hacen referencia a las capacitaciones participativas, el entrenamiento por medio de “degraded image”, la realización de gestión de autocontrol y retroalimentación para el uso de elementos de protección personal (EPP), la aplicación del Modelo de Proceso Paralelo Extendido; 2) intervenciones preventivas como la medición de alcoholimetría antes del turno, la presencia de personal de enfermería en minas de carbón y el reconocimiento de los predictores de la enfermedad para optimizar la prevención primaria; 3)intervenciones de vigilancia como la promovida en la metodología Estadísticas Europeas de Accidentes de Trabajo (EEAT) para la investigación de los accidentes de trabajo, la aplicación de las recomendaciones de la Organización Mundial de la Salud (OMS) para la detección de la neumoconiosis y 4) De carácter tecnológico consistente en la intervención de tareas a partir de los resultados de la aplicación del software desarrollado por el Instituto Nacional para la Seguridad y Salud Ocupacional (NIOSH). Estas intervenciones han demostrado ser eficaces en la promoción y prevención de accidentalidad y enfermedad ocupacional por lo cual se recomienda su aplicación en Colombia posterior al análisis de costo-efectividad.

How many facets are needed to represent the surface energy balance of an urban area?

We investigate the question of how many facets are needed to represent the energy balance of an urban area by developing simplified 3-, 2- and 1-facet versions of a 4-facet energy balance model of two-dimensional streets and buildings. The 3-facet model simplifies the 4-facet model by averaging over the canyon orientation, which results in similar net shortwave and longwave balances for both wall facets, but maintains the asymmetry in the heat fluxes within the street canyon. For the 2-facet model, on the assumption that the wall and road temperatures are equal, the road and wall facets can be combined mathematically into a single street-canyon facet with effective values of the heat transfer coefficient, albedo, emissivity and thermodynamic properties, without further approximation. The 1-facet model requires the additional assumption that the roof temperature is also equal to the road and wall temperatures. Idealised simulations show that the geometry and material properties of the walls and road lead to a large heat capacity of the combined street canyon, whereas the roof behaves like a flat surface with low heat capacity. This means that the magnitude of the diurnal temperature variation of the street-canyon facets are broadly similar and much smaller than the diurnal temperature variation of the roof facets. Consequently, the approximation that the street-canyon facets have similar temperatures is sound, and the road and walls can be combined into a single facet. The roof behaves very differently and a separate roof facet is required. Consequently, the 2-facet model performs similarly to the 4-facet model, while the 1-facet model does not. The models are compared with previously published observations collected in Mexico City. Although the 3- and 2-facet models perform better than the 1-facet model, the present models are unable to represent the phase of the sensible heat flux. This result is consistent with previous model comparisons, and we argue that this feature of the data cannot be produced by a single column model. We conclude that a 2-facet model is necessary, and for numerical weather prediction sufficient, to model an urban surface, and that this conclusion is robust and therefore applicable to more general geometries.

Referencing of street-level flows measured during the DAPPLE 2004 campaign

Street-level mean flow and turbulence govern the dispersion of gases away from their sources in urban areas. A suitable reference measurement in the driving flow above the urban canopy is needed to both understand and model complex street-level flow for pollutant dispersion or emergency response purposes. In vegetation canopies, a reference at mean canopy height is often used, but it is unclear whether this is suitable for urban canopies. This paper presents an evaluation of the quality of reference measurements at both roof-top (height = H) and at height z = 9H = 190 m, and their ability to explain mean and turbulent variations of street-level flow. Fast response wind data were measured at street canyon and reference sites during the six-week long DAPPLE project field campaign in spring 2004, in central London, UK, and an averaging time of 10 min was used to distinguish recirculation-type mean flow patterns from turbulence. Flow distortion at each reference site was assessed by considering turbulence intensity and streamline deflection. Then each reference was used as the dependent variable in the model of Dobre et al. (2005) which decomposes street-level flow into channelling and recirculating components. The high reference explained more of the variability of the mean flow. Coupling of turbulent kinetic energy was also stronger between street-level and the high reference flow rather than the roof-top. This coupling was weaker when overnight flow was stratified, and turbulence was suppressed at the high reference site. However, such events were rare (<1% of data) over the six-week long period. The potential usefulness of a centralised, high reference site in London was thus demonstrated with application to emergency response and air quality modelling.

A field study of factors influencing the concentrations of a traffic-related pollutant in the vicinity of a complex urban junction

The paper describes a field study focused on the dispersion of a traffic-related pollutant within an area close to a busy intersection between two street canyons in Central London. Simultaneous measurements of airflow, traffic flow and carbon monoxide concentrations ([CO]) are used to explore the causes of spatial variability in [CO] over a full range of background wind directions. Depending on the roof-top wind direction, evidence of both flow channelling and recirculation regimes were identified from data collected within the main canyon and the intersection. However, at the intersection, the merging of channelled flows from the canyons increased the flow complexity and turbulence intensity. These features, coupled with the close proximity of nearby queuing traffic in several directions, led to the highest overall time-average measured [CO] occurring at the intersection. Within the main street canyon, the data supported the presence of a helical flow regime for oblique roof-top flows, leading to increased [CO] on the canyon leeward side. Predominant wind directions led to some locations having significantly higher diurnal average [CO] due to being mostly on the canyon leeward side during the study period. For all locations, small changes in the background wind direction could cause large changes in the in-street mean wind angle and local turbulence intensity, implying that dispersion mechanisms would be highly sensitive to small changes in above roof flows. During peak traffic flow periods, concentrations within parallel side streets were approximately four times lower than within the main canyon and intersection which has implications for controlling personal exposure. Overall, the results illustrate that pollutant concentrations can be highly spatially variable over even short distances within complex urban geometries, and that synoptic wind patterns, traffic queue location and building topologies all play a role in determining where pollutant hot spots occur.

Short-range urban dispersion experiments using fixed and moving sources

Four perfluorocarbon tracer dispersion experiments were carried out in central London, United Kingdom in 2004. These experiments were supplementary to the dispersion of air pollution and penetration into the local environment (DAPPLE) campaign and consisted of ground level releases, roof level releases and mobile releases; the latter are believed to be the first such experiments to be undertaken. A detailed description of the experiments including release, sampling, analysis and wind observations is given. The characteristics of dispersion from the fixed and mobile sources are discussed and contrasted, in particular, the decay in concentration levels away from the source location and the additional variability that results from the non-uniformity of vehicle speed. Copyright © 2009 Royal Meteorological Society

Results from the Covered Catchment Experiment at Gårdsjön, Sweden, after ten years of clean precipitation treatment

The Covered Catchment Experiment at Gordsjon is a large scale forest ecosystem manipulation, where acid precipitation was intercepted by a 7000 m(2) plastic roof and replaced by 'clean precipitation' sprinkled below the roof for ten years between 1991 and 2001. The treatment resulted in a strong positive response of runoff quality. The runoff sulphate, inorganic aluminium and base cations decreased, while there was a strong increase in runoff ANC and a moderate increase in pH. The runoff continued to improve over the whole duration of the experiment. The achieved quality was, however, after ten years still considerably worse than estimated pre-industrial runoff at the site. Stable isotopes of sulphur were analysed to study the soil sulphur cycling. At the initial years of the experiment, the desorption of SO4 from the mineral soil appeared to control the runoff SO4 concentration. However, as the experiment proceeded, there was growing evidence that net mineralisation of soil organic sulphur in the humus layer was an additional source of SO4 in runoff. This might provide a challenge to current acidification models. The experiment convincingly demonstrated on a catchment scale, that reduction in acid deposition causes an immediate improvement of surface water quality even at heavily acidified sites. The improvement of the runoff appeared to be largely a result of cation exchange processes in the soil due to decreasing concentrations of the soil solution, while any potential change in soil base saturation seemed to be less important for the runoff chemistry over the short time period of one decade. These findings should be considered when interpreting and extrapolating regional trends in surface water chemistry to the terrestrial parts of ecosystems.

In-street wind direction variability in the vicinity of a busy intersection in central London

We present results from fast-response wind measurements within and above a busy intersection between two street canyons (Marylebone Road and Gloucester Place) in Westminster, London taken as part of the DAPPLE (Dispersion of Air Pollution and Penetration into the Local Environment; www.dapple.org.uk) 2007 field campaign. The data reported here were collected using ultrasonic anemometers on the roof-top of a building adjacent to the intersection and at two heights on a pair of lamp-posts on opposite sides of the intersection. Site characteristics, data analysis and the variation of intersection flow with the above-roof wind direction (θref) are discussed. Evidence of both flow channelling and recirculation was identified within the canyon, only a few metres from the intersection for along-street and across-street roof-top winds respectively. Results also indicate that for oblique rooftop flows, the intersection flow is a complex combination of bifurcated channelled flows, recirculation and corner vortices. Asymmetries in local building geometry around the intersection and small changes in the background wind direction (changes in 15-min mean θref of 5–10 degrees) were also observed to have profound influences on the behaviour of intersection flow patterns. Consequently, short time-scale variability in the background flow direction can lead to highly scattered in-street mean flow angles masking the true multi-modal features of the flow and thus further complicating modelling challenges.

Bryophyte diversity and community structure on thatched roofs of the Holnicote Estate, Somerset, U.K.

We investigated patterns of bryophyte species richness and community structure, and their relation to roof variables, on thatched roofs of the Holnicote Estate, South Somerset. Thirty-two bryophyte species were recorded from 28 sampled roofs, including the globally rare and endangered thatch moss, Leptodontium gemmascens. Multiple regression analyses revealed that thatch age has a highly significant positive effect on the number of species present, accounting for nearly half the observed variation in species richness after removal of outliers. Aspect has a slight and marginally significant effect on species diversity (accounting for an additional 6% of variation), with north-facing samples having slightly more species. Age also has a significant impact on total bryophyte cover after removal of outlying observations. TWINSPAN analysis of bryophyte cover data suggests the existence of at least five discrete communities. Simple Discriminant Analyses indicate that these communities occupy different ecological subspaces as defined by the measured roof variables, with pitch, aspect and thatch age emerging as especially significant attributes. Contingency Analysis indicates that some communities are disfavoured by water reed as compared to wheat straw. The findings are significant for understanding the structure of bryophyte communities, for evaluating the effect of bryophyte cover on thatch performance, and for conservation of thatch communities, especially those harbouring rare species.

Potential of making - Over to sustainable buildings in the Kingdom of Bahrain

Two unique large buildings in the Kingdom of Bahrain were selected for make-over to sustainable buildings. These are the Almoayyed Tower (the first sky scraper) and the Bahrain International Circuit, BIC (The best world Formula 1 Circuit). The amount of electricity extracted from using renewable energy resource (solar and wind), integrated to the buildings-has been studied thoroughly. For the first building, the total solar electricity from the PV installed at the roof and the 4 vertical facades was found 3 017 500 kWh annually (3 million kWh), i.e. daily energy of 8219 kWh (enough to Supply electricity for 171 houses, each is rated as 2 kW house-in Europe the standard is 1.2 kW). This means that the annual solar electricity produced will be nearly 3 million kWh. This correspond to annual CO, reduction of 3000 t (assuming each kWh of energy from natural gas lead to emission of 1 kg of CO2). For the second building (BIC) the solar electricity from PV panels installed at the roof top, fixed at tilt angle of 26 degrees facing south, will provide annual solar electricity of is 2.8 x 10(6) kWh. The solar electricity from PV panels installed on the windows (12,000 m(2)) will be 45.3 x 10(6) kWh. This means that the total annual electrical power from PV panels (windows and roofs) will be nearly 12 MW (32 kW per day). The CO2 reduction will be 48,000 t. Under the carbon trading or CDM scheme the revenue (or the reward) would be (sic)480,000 million annually (the reward is (sic)10 per tonnes of CO2). The BIC circuit can have diversified electricity supply, i.e. from solar radiation (PV), from solar heat (CSP) and from wind (wind turbines), assuring its sustainability as well as reducing the CO2 emission.

Building integration photovoltaic module with reference to Ghana: using triple junction amorphous silicon

This paper assesses the potential for using building integrated photovoltaic (BIPV) roof shingles made from triple-junction amorphous silicon (3a-Si) for electrification and as a roofing material in tropical countries, such as Accra, Ghana. A model roof was constructed using triple-junction amorphous (3a-Si) PV on one section and conventional roofing tiles on the other. The performance of the PV module and tiles were measured, over a range of ambient temperatures and solar irradiance. PVSyst (a computer design software) was used to determine the most appropriate angle of tilt. It was observed that 3a-Si performs well in conditions such as Accra, because it is insensitive to high temperatures. Building integration gives security benefits, and reduces construction costs and embodied energy, compared to freestanding PV systems. Again, it serves as a means of protection from salt spray from the oceans and works well even when shaded. However, compared to conventional roofing materials, 3a-Si would increase the indoor temperature by 1-2 °C depending on the surface area of the roof covered with the PV modules. The results presented in this research enhance the understanding of varying factors involved in the selection of an appropriate method of PV installation to offset the short falls of the conventional roofing material in Ghana.