Uso de resíduos de queima de casca de café e argila da região sul da Bahia na obtenção de isolador elétrico cerâmico

The electrical ceramic insulators industry, uses noble raw materials such as siliceous and aluminous clays of white burning, in order to provide plasticity of the mass and contribute to electrical and mechanical properties required of the product, and feldspar with the flux function In literature references the composition of the masses indicates that the clay participates in percentage between 20 and 32, and feldspar 8 to 35, these materials have significant cost. In this research was performed the total replacement of commercial clay, for white burning clay from Santa Luzia region in southern Bahia and partial replacement of feldspar by ash residue of husk conilon coffee burning, from extreme south of Bahia. The objective of replacement these raw materials is to aver its technical feasibility and call attention for the embryo pole of ceramic industry for the existing in the south and extreme south of Bahia, which has significant reserves of noble raw materials such as clay white burning, kaolin, quartz and feldspar, and generates significant volume of gray husk conilon coffee as alternate flux. Clay Santa Luzia is prima noble material whose current commercial application is the production of white roofing. The residue of coffee husk ash is discarded near of production sites and is harmful to the environment. Phase diagrams and statistic design of experiments, were used for optimization and cost savings in research. The results confirmed the expectations of obtaining electrical ceramic insulators, with white burning clay of Santa Luzia and partial replacement up to 35.4% of feldspar, by treaty residue of conilon ash coffee husk burning. The statistic design that showed best results was for formulation with percentages of: clay 26.4 to 30.4%; kaolin 14.85 to 17.1%; feldspar 12.92 to 16.96%; R2 residue 7.08 to 9.2% and Quartz 32.5 to 38.75%, relative to the total mass of the mixture. The best results indicated; 0.2 to 1.4% apparent porosity , water absorption 0.1 to 0.7%, flexural strength 35 to 45MPa , dielectric strength 35-41 kV/cm , the transverse resistivity 8x109 2.5x1010 Ω.cm and for the dielectric constant ε/ε0 7 to 10.4, specification parameters for manufacturing ceramic electrical insulators of low and medium voltage.

Utilização da cinza da casca de arroz em cimentação de poços de petróleo

Pozzolanic materials such as rice husk ash are widely used to substitute part of cement, because they react with calcium hydroxide (CH) producing calcium silicate hydrate (C-S-H), which aggregate better physical, chemical and mechanical properties to the cement slurry. The usage of rice husk biomass ash from agribusiness in addition to or partially replacing cement is a noble purpose and a good way of sustainable development which currently is an obsession around the world. The ashes utilized in this study were characterized by: scanning electron microscopy technique (SEM), Fourier transform infrared spectroscopy (FTIR), Energy-dispersive X-ray spectroscopy (EDX) and BET method. The pozzolanic activity of RHA and WRHA in cement slurries was evaluated by: thermal-gravimetric technique and derivative thermogravimetry (TGA/DTG), X-ray diffraction (XRD) and Compressive Strength. The slurries formulated with additions of 10% and 20% of RHA and WRHA were cured for 28 days at 58 °C. The results of thermal analysis demonstrated that a 20% WRHA addition caused a reduction of approximately 73% of Portlandite (calcium hydroxide – CH) phase related to standard slurry (STD). The XRD scans also demonstrated the reduction of the Portlandite peaks’ intensity for each slurry compared with STD slurry. The RHA and WRHA react chemically with Portlandite producing calcium silicate hydrate (C-S-H), confirming their effect as a pozzolanic agent. The WRHA presented the best results as a pozzolanic material.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Techno-Economic and Life Cycle Assessment for the Production of Green Composites

Botanically, green composites belong to an economically important seed plant family that includes maize, wheat, rice, and sorghum known as Saccharum offi cinarum. There are so many natural fibers available in the environment such as rice husk, hemp fibers, flax fibers, bamboo fibers, coconut fiber, coconut coir, grawia optiva and many others also. Life Cycle Assessment (LCA) is a process to estimate the environmental feature and potential impacts related to a product, by organizing a directory of pertinent inputs and outputs of a product system, assessing the potential environmental impacts related with the said inputs and outputs, explaining the results of the inventory analysis and impact evaluation phases in connection to the objectives of the study. Particularly Bagasse, an agricultural residue not only becomes a problem from the environmental point of view, but also affects the profitability of the sugarcane industries. This chapter discusses the properties, processing methods and various other aspects including economic and environmental aspects related to green composites.

Efeito de agentes de controle sobre a qualidade reprodutiva de rainhas de Apis mellifera L. (Hymenoptera: Apidae) africanizadas

The agriculture with the use of products with less environmental impact is expanding. In it, the producers offer their products without the use of synthetic chemical inputs, solving the phytosanitary problems with the use of biological or alternative control agents such as parasites, predators, entomopathogenic, alternative products, plant extracts and essential oils. These products can be considered safe to non-target organisms, but studies are needed to find these features on natural enemies and on the beneficial insects such as bees, common frequenter of cultures. In this sense, this study aims to evaluate the effects of control over reproductive quality queens of Apis mellifera L. (Hymenoptera: Apidae) Africanized. For this, it tested the action of control products on the production of A. mellifera queens, using the commercial entomopathogenic fungus Boveril® 1,0x108 (Beauveria bassiana) and aqueous extract of pomegranate (Punica granatum) at a concentration of 5% sterile distilled water with Tween (0.01%) and sterile distilled water (controls). The treatments were incorporated into a tissue type gauze, wrapped in an acrylic plate and packed inside minirrecrias type colonies for the production of queens on the day before the transfer of larvae. The next day were introduced battens with 30 domes with larvae to produce queens, so the workers have contacted the agent tested. From the emergence of all the queens, they were monitored to determine the measures of body weight (mg), length and width of wing and abdomen, length, width and height of the chest (mm) as well as the time of emergence of queens. The next step was evaluated the influence of the control agents in production creates, performing measurements of creating areas in cm2 for six straight weeks. It was found that the area creates Queens did not differ among the treatments. Histological analysis of hipofaringeanas of workers glands that came into contact with the control agents and the midgut of virgin queens were also held. Histological analysis differences were observed in the tissues when the treatments were compared with the respective controls.

APROVEITAMENTO DA CASCA DO COCO-VERDE ( Cocos nucifera L.) PARA PRODUÇÃO DE POLPA CELULÓSICA

A casca do coco-verde é um resíduo do consumo da água de coco. Em cidades litorâneas este resíduo já tem se tornado um grande problema, pois é de difícil decomposição. O presente estudo teve como objetivo avaliar a casca do coco-verde ( Cocos nucifera L.) para a produção de celulose kraft. A matéria-prima foi caracterizada com relação à densidade básica, composição química, dimensão das fibras e proporção de elementos anatômicos. Foram realizados três cozimentos-teste sendo que um deles foi escolhido para repetição. Em cada um deles variou-se a carga alcalina visando à elaboração de curvas de cozimento. Nos resultados do processo de polpação foram encontrados valores altos de número kappa, baixos rendimentos e baixos teores de rejeito. As seguintes características do material, baixa densidade básica (0,128 g/cm³), alta quantidade de extrativos (33,68%) e baixa proporção de fibras (22,11%), corroboraram para estes resultados. Assim, a produção de polpa celulósica a partir da casca do coco-verde pelo processo kraft, não se mostrou como uma alternativa viável tecnicamente.

Casca de arroz como adsorvente para extração de micotoxinas em cebola

A produção mundial de arroz chega a 80 milhões de toneladas ao ano, considerando que as cascas representam 20% deste valor, anualmente são geradas cerca de 1.162.000 toneladas desse rejeito. Há alguns anos, esse material era descartado no ambiente, atualmente as leis de proteção ambiental, demandaram na preocupação com resíduos de casca de arroz (FOLETO, 2005). Segundo Mayer (2006) a casca leva aproximadamente 5 anos para se decompor e exala um volume elevado de metano, um dos gases responsáveis pelo efeito estufa. Visando proteger a integridade do meio ambiente, estão sendo buscadas alternativas para reduzir os impactos ambientais do descarte e recuperar os investimentos na cultura do grão. Devido seu alto teor de silício a casca de arroz, é matéria-prima de grande interesse para aplicação em vários ramos: indústria eletrônica, cerâmica e na agricultura e também pode ser utilizada como fonte energética e ser aplicadas como adsorvente, em análises químicas (FOLETO, 2005; ROSA, 2009). Neste trabalho o objetivo foi padronizar método para a determinação das aflatoxinas B1, B2, G1, G2 e ocratoxiana A em cebola, empregando a técnica de extração, Dispersão da Matriz em Fase Sólida (MSPD), tendo a casca de arroz como adsorvente, de forma a possibilitar a determinação dos contaminantes empregando cromatografia de camada delgada de alta eficiência (HPTLC) e/ou cromatografia líquida de alta eficiência acoplada a detector de fluorescência (HPLC-FD). A cebola (Allium cepa L.) foi a matriz escolhida devido sua importância econômica, ela é a terceira hortaliça mais importante economicamente no Brasil, depois do tomate e da batata. O país está entre os dez maiores produtores do mundo, sendo que na safra de 2010 a produção foi de 1.548.146 toneladas. Dentre os estados que se destacam pela sua produção estão: Santa Catarina, São Paulo e Rio Grande do Sul. No entanto, a cebola assim como os demais alimentos é suscetível à contaminação fúngica e se entre a microbiota estiverem espécies toxigênicas pode ocorrer à produção de micotoxinas. O método foi validado avaliando-se curva analítica, linearidade, limites de detecção e quantificação, precisão (repetitividade e precisão intermediária) e exatidão (recuperação) para cada tipo de determinação cromatográfica. Para HPTLC, os limites de detecção variaram entre 0,33-5µg Kg-1 e os de quantificação entre 1-15µg Kg-1 Para o método HPLC-FD os limites de detecção variaram entre 0,003– 0,26 µg Kg-1 e os de quantificação 0,03 – 2,6 µg Kg-1 . As recuperações para o método HPTLC variaram entre 76- 95% e para HPLC-FD variaram entre 72-88%. O método desenvolvido foi aplicado para verificar a ocorrência de micotoxinas em 14 amostras de cebola. A contaminação com aflatoxinas foi verificada em 43% das amostras analisadas. O nível máximo encontrado foi de 90 µg Kg-1 para aflatoxina B2 em uma amostra de cebola crioula, com o defeito de mancha negra.

Ocular injuries and eye care seeking patterns following injuries among cocoa farmers in Ghana.

Background: The work environment of cocoa farmers exposes them to several ocular hazards that predispose them to eye diseases and injuries. However, the extent of ocular injuries and health seeking patterns following these injuries are unknown among cocoa farmers in Ghana. Objectives: To determine the prevalence of ocular injuries and health seeking behaviour following injury among cocoa farmers in Ghana. Methods: Five hundred and fifty six participants were recruited through simple random sampling using a multistage approach from four cocoa growing districts in Ghana. A structured questionnaire was used to collect relevant information such as demography, ocular hazards and injuries experienced. An ocular examination was also conducted to assess the eye health of the participants. Descriptive and regression statistics were used to analyze the data. The rate of ocular injuries was calculated by using the number of injuries reported that resulted in lost work time/days divided by the number of worker years at risk of injury (sum of years worked in cocoa farms for all the participants). Results: The rate of ocular injuries was 11.3/1000 worker years (95% CI: 9.4 - 31) which led to lost work time of 37.3/1000 worker years (95% CI: 34.1 - 40.8). The major causes of ocular injury were plants/branches (n=73, 51.1%), chemicals (n=27, 18.9%), cocoa pod/husk (n=14, 9.8%) and occurred mostly during weeding, harvesting and chemical spraying. Few (n=34, 6.1%) participants reported the use of ocular protection. Fifty-five (38.5%) participants visited the local chemical shops, while 37 (25.9%) visited hospitals/clinics for ocular treatment of their injuries. Conclusion: There is a high rate of ocular injuries among cocoa farmers who make insufficient use of appropriate eye care services. There is the need for eye health education among cocoa farmers in Ghana. Keywords:

Síntese e impregnação de peneiras moleculares Fe MCM-41 derivada de sílica da casca do arroz

The mesoporous molecular sieves of the MCM-41 and FeMCM-41 type are considered promissory as support for metals used as catalysts in oil-based materials refine processes and as adsorbents for environmental protection proposes. In this work MCM-41 and FeMCM41 were synthesized using rice husk ash - RHA as alternative to the conventional silica source. Hydrothermal synthesis was the method chosen to prepare the materials. Pre-defined synthesis parameters were 100°C for 168 hours, later the precursor was calcinated at 550°C for 2 hours under nitrogen and air flow. The sieves containing different proportions of iron were produced by two routes: introduction of iron salt direct synthesis; and a modification post synthesis consisting in iron salt 1 % and 5% impregnation in the material followed by thermal decomposition. The molecular sieves were characterized by X ray diffraction XRD, Fourier transform infrared spectroscopy FT-IR, X ray fluorescence spectroscopy XFR, scanning electronic microscopy SEM, specific surface area using the BET method, Termogravimetry TG. The kinetic model of Flynn Wall was used with the aim of determining the apparent activation energy of the surfactant remove (CTMABr) in the MCM- 41 porous. The analysis made possible the morphology characterization, identifying the presence of hexagonal structure typical for mesoporous materials, as well as observation of the MCM41 and iron of characteristic bands.

Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid

Estudo da potencialidade da incorporação de resíduo de granito e da queima da casca do café em cerâmica vermelha

The industrial production of ornamental rocks and the burning of coffee husk generate waste that is discarded into the environment. However, with the study of the incorporation of these residues in ceramic products, may be found an alternative to reducing environmental impacts and detrimental effects on human health caused by its indiscriminate disposal of waste in nature. Thus, this work aimed to study the addition of ashes of the coffee husk and granite residue in matrix of red ceramic. The raw materials were dry milled and sieved to mesh 100. To characterize the raw materials were carried out analyzes of X-ray diffraction (XRD), X-ray fluorescence (XRF), particle size analysis (PSA), differential thermal analysis (DTA) and thermogravimetric analysis (TG). Six formulations were prepared where the clay content was kept constant (70%wt) and ashes contents and granite residue varied from 10, 15, 20 and 30%. Dilatometrics analyzes were performed at four selected formulations, containing them: 100% clay (A100); 70% clay and 30% ashes (A70C30); 70% clay and 30% granite residue (A70G30); and 70% clay, 15% granite residue and 15% ashes (A70G15C15). The samples were prepared by uniaxial compaction with pressure of 25 MPa, and fired at temperatures of 800°C, 850ºC, 900ºC, 950ºC, 1000ºC and 1100°C. Assays were performed to determine the linear shrinkage of burning (LSB), water absorption (WA), apparent porosity (AP), density (D) and tensile bending. Also were performed analyzes of X-ray diffraction (XRD) and scanning electron microscopy (SEM) of the samples fired. The formulations incorporating granite residue and/or ashes reached the required limits of water absorption according to NBR 15270-1 and NBR 15310 and tensile bending according to classical literature (SANTOS, 1989) necessary for the production of tiles and ceramic block for masonry sealing

Adição de subprodutos da cinza da casca de café (coffea canephora) em massa cerâmica para porcelanato

To produce porcelain tiles fluxing agents are used in order to obtain a liquid phase during firing. This liquid phase fills the pores decreasing porosity, water absorption and contributes to material densification. In the porcelain tiles industry, feldspar is the main flux material used, with quantities ranging between 35 and 50%. Studies focus on the discovery of materials with flux characteristics that can reduce the consumption of feldspar by porcelain tiles industry. In this context, the coffee husk ashes, a residue obtained when coffee husks are burned to produce heat for the dryers during the processing of the green fruit, have as main chemical constituents potassium, calcium and magnesium, giving them characteristics of fluxing material. Brazil is the largest coffee producer in the world and is responsible for over 30% of the world s production. In this work a physical treatment of coffee husk ash was carried out in order to eliminate the organic matter and, after this, two by-products were obtained: residual wastes R1 and R2. Both residues were added separately as single fluxes and also in association with feldspar in mixtures with raw materials collected in a porcelain industry located in Dias d Ávila-Ba. The addition of these residues aimed to contribute to the reduction of the consumption of feldspar in the production of porcelain tiles. Specimens were produced with dimensions of 60 mm x 20 mm x 6 mm in an uniaxial die with compacting pressure of 45 MPa. The samples were heated to a temperature of 1200 °C, for 8 minutes. Tests were performed to characterize the raw materials by XRF, XRD, particle size analysis, DTA and TGA and, additionally, the results of the physical properties of water absorption, apparent porosity, linear shrinkage, density, dilatometry, flexural strength and SEM of sintered body were analyzed. Additions of less than 8% of the residue R1 contributed to the decrease of porosity, but the mechanical strength of the samples was not satisfactory. Additions of 5% the R2 residue contributed significantly to decrease the water absorption and apparent porosity, and also to increase the mechanical strength. Samples with addition of feldspar associated with the R2 residue, in proportions of 6.7% of R2 and 6.7% of feldspar, led to results of water absorption of 0.12% and mechanical strength of 46 MPa, having parameters normalized to the manufacture of porcelain stoneware tiles

Bebidas espirituosas do Algarve

Tese de Doutoramento, Química, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2016

In vivo analgesic activity and safety assessment of Vitis vinifera L and Punica granatum L fruits extracts

Purpose: To investigate the analgesic properties of fruit extracts of Vitis vinifera (grape) and Punica granatum (pomegranate) in Albino mal mice. Methods: The analgesic activity of fruit extracts of V. vinifera and P. granatum were examined in vivo using thermal stimulus assays (i.e., tail immersion and hot plate) and acetic acid-induced writhing test using acetylsalicylic acid (0.1 g/kg, per os) as standard. The extracts were administered orally in doses of 1.0, 2.0 and 3.0 g/kg. Results: In acetic acid writhes test, both fruit extract pretreatments (1.0, 2.0 and 3.0 g/kg, per os) significantly decreased the number of writhes (p < 0.0001) in a dose-dependent manner compared to control. The Index of Pain Inhibition (IPI) values following V. vinifera extract treatments were 36.52 % (1.0 g/kg), 66.67 % (2.0 g/kg) and 89.71 % (3.0 g/kg) which were significantly different from those for P. granatum extracts (45.39 %, 1.0 g/kg), 70.93 %, 2.0 g/kg) and 86.88 %, 3.0 g/kg) at equivalent doses of 2.0 and 3.0 g/kg of the extracts The fruit extracts of both species increased the reaction latency time. In tail-immersion assay, only the fruit extract of P. granatum significantly increased the response to heat stimulus at doses of 2.0 g/kg (p < 0.05). Conclusion: The hydroalcohol fruit extracts of P. granatum and V. vinifera have potential analgesic effects. Further studies are needed to determine the active component responsible for this effect.