Extração supercrítica do óleo de linhaça: construção do extrator, estudo de parâmetros de processo, avaliação química e antioxidante do produto

The aim of the present study was to extract vegetable oil from brown linseed (Linum usitatissimum L.), determine fatty acid levels, the antioxidant capacity of the extracted oil and perform a rapid economic assessment of the SFE process in the manufacture of oil. The experiments were conducted in a test bench extractor capable of operating with carbon dioxide and co-solvents, obeying 23 factorial planning with central point in triplicate, and having process yield as response variable and pressure, temperature and percentage of cosolvent as independent variables. The yield (mass of extracted oil/mass of raw material used) ranged from 2.2% to 28.8%, with the best results obtained at 250 bar and 50ºC, using 5% (v/v) ethanol co-solvent. The influence of the variables on extraction kinetics and on the composition of the linseed oil obtained was investigated. The extraction kinetic curves obtained were based on different mathematical models available in the literature. The Martínez et al. (2003) model and the Simple Single Plate (SSP) model discussed by Gaspar et al. (2003) represented the experimental data with the lowest mean square errors (MSE). A manufacturing cost of US$17.85/kgoil was estimated for the production of linseed oil using TECANALYSIS software and the Rosa and Meireles method (2005). To establish comparisons with SFE, conventional extraction tests were conducted with a Soxhlet device using petroleum ether. These tests obtained mean yields of 35.2% for an extraction time of 5h. All the oil samples were sterilized and characterized in terms of their composition in fatty acids (FA) using gas chromatography. The main fatty acids detected were: palmitic (C16:0), stearic (C18:0), oleic (C18:1), linoleic (C18:2n-6) and α-linolenic (C18:3n-3). The FA contents obtained with Soxhlet dif ered from those obtained with SFE, with higher percentages of saturated and monounsaturated FA with the Soxhlet technique using petroleum ether. With respect to α-linolenic content (main component of linseed oil) in the samples, SFE performed better than Soxhlet extraction, obtaining percentages between 51.18% and 52.71%, whereas with Soxhlet extraction it was 47.84%. The antioxidant activity of the oil was assessed in the β-carotene/linoleic acid system. The percentages of inhibition of the oxidative process reached 22.11% for the SFE oil, but only 6.09% for commercial oil (cold pressing), suggesting that the SFE technique better preserves the phenolic compounds present in the seed, which are likely responsible for the antioxidant nature of the oil. In vitro tests with the sample displaying the best antioxidant response were conducted in rat liver homogenate to investigate the inhibition of spontaneous lipid peroxidation or autooxidation of biological tissue. Linseed oil proved to be more efficient than fish oil (used as standard) in decreasing lipid peroxidation in the liver tissue of Wistar rats, yielding similar results to those obtained with the use of BHT (synthetic antioxidant). Inhibitory capacity may be explained by the presence of phenolic compounds with antioxidant activity in the linseed oil. The results obtained indicate the need for more detailed studies, given the importance of linseed oil as one of the greatest sources of ω3 among vegetable oils

Estudo da secagem do pedúnculo do caju em sistemas convencional e solar: modelagem e simulação do processo

This work aims to study the drying of cashew-nut pulp with different lay-out of dryers using conventional and solar energy. It concerns with the use of exceeding of the regional raw material and the suitable knowledge for the applicability of the drying systems as pathway for food conservation. Besides, it used renewable sources as solar energy to dry these agroindustrial products. Runs were carried out using a conventional tray-dryer with temperature, air velocity control and cashew slice thickness of 55°C, 65°C, 75°C; 3.0; 4.5, 6.0 m s-1; 1.0; 1.5 and 2.0 cm, respectively, in order to compare the studied systems. To evaluate the conventional tray-dryer, it was used a diffusional model of 2nd Fick´s law, where the drying curves were quite well fitted to an infinite flat plate design. For the drying runs where the room temperature had no control, it was developed a phenomenological-mathematical model for the solar dryer with indirect radiation under natural and forced convection based on material and energy balances of the system. Besides, it was carried out assays in the in natura as well as dehydrated, statistic analysis of the experimental drying data, sensorial analysis of the final dry product and a simplified economical analysis of the systems studied

Secagem de misturas de polpa de frutas tropicais em leito de jorro

Drying of fruit pulps in spouted beds of inert particles has been indicated as a viable technique to produce fruit powders. Most of the processes employed to produce dried fruit pulps and juices, such as Foam Mat, encapsulation by co-crystallization and spray drying utilize adjuvant and additives (such as thickeners, coating materials, emulsifiers, acidulants, flavors and dyes), which is not always desirable. The fruit pulp composition exerts an important effect on the fruit powder production using a spouted bed. In the study by Medeiros (2001) it was concluded that lipids, starch and pectin contents play an important role on the process performance, enhancing the powder production; however, the drying of fruit pulps containing high content of reducing sugars (glucose and fructose) is practically unviable. This work has the objective of expanding the studies on drying of fruit pulps in spouted bed with aid of adjuvant (lipids, starch and pectin) aiming to enhance the dryer performance without jeopardizing the sensorial quality of the product. The optimum composition obtained by Medeiros (2001) was the basis for preparing the mixtures of pulps. The mixture formulations included pulps of mango (Mangifera indica), umbu (Spondias tuberosa) and red mombin (Spondia purpurea) with addition of cornstarch, pectin and lipids. Different products were used as lipids source: olive and Brazil nut oils, coconut milk, heavy milk, powder of palm fat and palm olein. First of all, experiments were conducted to define the best formulation of the fruit pulps mixture. This definition was based on the drying performance obtained for each mixture and on the sensorial characteristics of the dry powder. The mixture formulations were submitted to drying at fixed operating conditions of drying and atomizing air flow rate, load of inert particles, temperature and flow rate of the mixture. The best results were obtained with the compositions having powder of palm fat and palm olein in terms of the drying performance and sensorial analysis. Physical and physicochemical characteristics were determined for the dry powders obtained from the mixtures formulations. Solubility and reconstitution time as well as the properties of the product after reconstitution were also evaluated. According to these analyses, the powder from the mixtures formulations presented similar characteristics and compatible quality to those produced in other types of dryers. Considering that the palm olein is produced in Brazil and that it has been used in the food industry substituting the palm fat powder, further studies on drying performance were conducted with the composition that included the palm olein. A complete factorial design of experiments 23, with three repetitions at the central point was conducted to evaluate the effects of the air temperature, feeding flow rate and intermittence time on the responses related to the process performance (powder collection efficiency, material retained in the bed and angle of repose of the inert particles after the process) and to the product quality (mean moisture content, loss of vitamin C and solubility). Powder production was uniform for the majority of the experiments and the higher efficiency with lower retention in the bed (59.2% and 1.8g, respectively) were obtained for the air temperature of 80°C, mixture feed rate of 5ml/min in intervals of 10 min. The statistical analysis of the results showed that the process variables had individual or combined significant influences on the powder collection efficiency, material retention in the bed, powder moisture content and loss of vitamin C. At the experimental ranges of this work, the angle of repose and solubility were not influenced by the operating variables. From the results of the experimental design, statistical models were obtained for the powder moisture content and loss of vitamin C

Estudo da reidratação do feijão verde (Vigna unguiculata L. Walp) desidratado por micro-ondas com e sem pré-tratamento osmótico

The green bean has organoleptic and nutritional characteristics that make it an important food source in tropical regions such as the Northeast of Brazil. It is a cheap source of protein and important for nutrition of rural population contributing significantly in subsistence farming of the families from Brazil s northeast. It is consumed in entire region and together with the dry meat and other products composes the menu of typical restaurants, being characterized as an important product for economy of Northeast. The green bean is consumed freshly harvested and has short cycle, being characterized as a very perishable food, which hampers your market. The drying method is an alternative to increase the lifetime and provide a reduction volume of this product making easier your transportation and storage. However is necessary to search ways of drying which keep the product quality not only from the nutritional standpoint but also organoleptic. Some characteristics may change with the drying process such as the coloring, the rehydration capacity and the grains cooking time. The decrease of drying time or of exposure of the grains to high temperature minimizes the effects related with the product quality loss. Among the techniques used to reduce the drying time and improve some characteristics of the product, stands out the osmotic dehydration, widely used in combined processes such as the pretreatment in drying food. Currently the use of the microwaves has been considered an alternative for drying food. The microwave energy generates heat inside of materials processed and the heating is practically instantaneous, resulting in shorter processing times and product quality higher to that obtained by conventional methods. Considering the importance of the green beans for the Northeast region, the wastefulness of production due to seasonality of the crop and your high perishability, the proposal of this thesis is the study of drying grain by microwaves with and without osmotic pretreatment, focusing on the search of conditions of processes which favor the rehydration of the product preserving your organoleptic characteristics. Based on the analysis of the results of osmotic dehydration and dielectric properties was defined the operating condition to be used in pretreatment of the green bean, with osmotic concentration in saline solution containing 12,5% of sodium chloride, at 40°C for 20 minutes. The drying of green bean by microwave was performed with and without osmotic pretreatment on the optimized condition. The osmotic predehydration favored the additional drying, reducing the process time. The rehydration of dehydrated green bean with and without osmotic pretreatment was accomplished in different temperature conditions and immersion time according to a factorial design 22, with 3 repetitions at the central point. According to results the better condition was obtained with the osmotically pretreated bean and rehydrated at a temperature of 60°C for 90 minutes. Sensory analysis was performed comparing the sample of the green bean in natura and rehydrated in optimized conditions, with and without osmotic pretreatment. All samples showed a good acceptance rate regarding the analyzed attributes (appearance, texture, color, odor and taste), with all values above 70%. Is possible conclude that the drying of green bean by microwave with osmotic pretreatment is feasible both in respect to technical aspects and rehydration rates and sensory quality of the product

Concepção de um secador rotatório para secagem do cefalotórax do camarão

The present work has as objective the knowledge of the process of drying of the cephalothorax of shrimp to give support the industry to make possible the use of this byproduct. In this sense, the process conditions in this tray dryer and spouted bed were analyzed. With these results, it was projected and constructs a dryer with specific characteristics for the drying of the cephalothorax. The desorption isotherms were obtained by the dynamic method in the temperatures of 20, 35 and 50º C and in the interval of 10-90% of relative humidity. It was observed that the product in form of powder can be conserved with larger stability for lower relative humidity to 40%. The curves of drying of the dryer of fixed bed were adjusted for the models: single exponential, biparametric exponential and Page. The model biparametric exponential more adequately described all the drying conditions studied. The tests carry out in spouted bed showed high drying rate for the material in the paste form in beds active dynamicly-fluid, provely the necessity of a feeding in shorter intervals of time to increase the thermal efficiency of the process. The projected dryer, be considered the obtained results, it was a rotary dryer with inert bed, feed co-current, discharge in cyclone to take place the separation gas-solid, and feed carry out in intervals of 2 minutes. The optimization of the equipment projected it was accomplished used the complete factorial experimental design 24, this had as independent variables temperature velocity of the air, feed flow rate and encapsulated concentration (albumin), as variables answers the thermal efficiency, the moisture content of obtained powder, total time of test and the efficiency of production of powder in several points of processing. The results showed that the rotary dryer with inert bed can present, also, good results if applied industrially

Analysis of Semi-solid Processing for Metal Matrix Composite Synthesis Using Factorial Design

The main goal in this work is to conduct a quantitative analysis of the mechanical stir casting process for obtaining particulate metal matrix composites. A combined route of stirring at semi-solid state followed by stirring at liquid state is proposed. A fractional factorial design was developed to investigate the influence and interactions of factors as: time, rotation, initial fraction and particle size, on the incorporated fraction. The best incorporations were obtained with all factors at high levels, as well as that very long stirring periods have no strong influence being particle size and rotation the most important factors on the incorporated fraction. Particle wetting occurs during stirring at semisolid state, highlighting the importance of the interactions between particles and the alloy globularized phase. The role of the alloying element Mg as a wettability-promoting agent is discussed. The shear forces resulting from the stirring system is emphasized and understood as the effect of rotation itself added to the propeller blade geometry.

Uso de regulador de crescimento em cultivares de feijão de inverno

A aplicação de reguladores vegetais, com a finalidade de aumentar a produtividade das culturas, tem merecido, nos últimos anos, grande atenção de pesquisadores. No entanto, alguns resultados têm se mostrado contraditórios. em face disto, este estudo teve como objetivo verificar os efeitos da aplicação de regulador vegetal sobre os componentes da produção e a produtividade de grãos de duas cultivares de feijão de inverno, em condições de Cerrado. O experimento foi realizado no outono-inverno de 2007, na Fazenda Experimental da Unesp, Campus de Ilha Solteira, localizada no município de Selvíria (MS). O delineamento experimental foi o de blocos casualizados, no esquema em faixas, com quatro repetições. Os tratamentos constituíram-se da combinação de cinco doses do regulador vegetal (0 L ha-1 0,5 L ha-1 1,0 L ha-1 1,5 L ha-1 e 2,0 L ha-1, que é composto por três hormônios vegetais (cinetina, ácido giberélico e ácido indolbutírico), em duas épocas de aplicação: no estádio vegetativo (V4) e reprodutivo (R5). Características vegetativas como altura das plantas de feijão, altura de inserção da primeira vagem, número de grãos por vagem e massa de 100 grãos não foram afetadas pela aplicação do produto. No entanto, sua aplicação no estádio reprodutivo (R5) aumentou o número de grãos por planta e a produtividade de grãos das cultivares de feijoeiro Carioca Precoce e IAC Apuã. Para este aumento, a melhor dose foi 2 L ha-1do regulador vegetal.

BRIDGE: uma ferramenta para o Design de Interfaces de Usuário baseada em especificações IMML

With hardware and software technologies advance, it s also happenning modifications in the development models of computational systems. New methodologies for user interface specification are being created with user interface description languages (UIDL). The UIDLs are a way to have a precise description in a language with more abstraction and independent of how will be implemented. A great problem is that even using these nowadays methodologies, we still have a big distance between the UIDLs and its design, what means, the distance between abstract and concrete. The tool BRIDGE (Interface Design Generator Environment) was created with the intention of being a linking bridge between a specification language (the Interactive Message Modeling Language IMML) and its implementation in Java, linking the abstract (specification) to the concrete (implementation). IMML is a language based on models, that allows the designer works in distinct abstraction levels, being each model a distinct abstraction level. IMML is a XML language, that uses the Semiotic Engineering concepts, that deals the computational system, with the user interface and its elements like a metacommunicative artifact, where these elements must to transmit a message to the user about what task must to be realized and the way to reach this goal. With BRIDGE, we intend to supply a lot of support to the design task, being the user interface prototipation the greater of them. BRIDGE allows the design becomes easier and more intuitive coming from an interface specification language

CrossMDA-SPL: uma abordagem para gerência de variabilidades dirigida por modelos e aspectos

This paper proposes a systematic approach to management of variability modelsdriven and aspects using the mechanisms of approaches Aspect-Oriented Software Development (AOSD) and Model-Driven Development (MDD). The main goal of the approach, named CrossMDA-SPL, is to improve the management(gerência), modularization and isolation ou separation of the variability of the LPSs of architecture in a high level of abstraction (model) at the design and implementing phases of development Software Product Lines (SPLs), exploiting the synergy between AOSD and MDD. The CrossMDA-SPL approach defines some artifacts basis for advance the separation clear in between the mandatory (bounden) and optional features in the architecture of SPL. The artifacts are represented by two models named: (i) core model (base domain) - responsible for specify the common features the all members of the SPL, and (ii) variability model - responsible for represent the variables features of SPL. In addition, the CrossMDA-SPL approach is composed of: (i) guidelines for modeling and representation of variability, (ii) CrossMDA-SPL services and process, and (iii) models of the architecture of SPL or product instance of SPL. The guidelines use the advantages of AOSD and MDD to promote a better modularization of the variable features of the architecture of SPL during the creation of core and variability models of the approach. The services and sub-processes are responsible for combination automatically, through of process of transformation between the core and variability models, and the generation of new models that represent the implementation of the architecture of SPL or a instance model of SPL. Mechanisms for effective modularization of variability for architectures of SPL at model level. The concepts are described and measured with the execution of a case study of an SPL for management systems of transport electronic tickets

Avaliação sistemática de abordagens de derivação de produto

Product derivation tools are responsible for automating the development process of software product lines. The configuration knowledge, which is responsible for mapping the problem space to the solution space, plays a fundamental role on product derivation approaches. Each product derivation approach adopts different strategies and techniques to manage the existing variabilities in code assets. There is a lack of empirical studies to analyze these different approaches. This dissertation has the aim of comparing systematically automatic product derivation approaches through of the development of two different empirical studies. The studies are analyzed under two perspectives: (i) qualitative that analyzes the characteristics of approaches using specific criteria; and (ii) quantitative that quantifies specific properties of product derivation artifacts produced for the different approaches. A set of criteria and metrics are also being proposed with the aim of providing support to the qualitative and quantitative analysis. Two software product lines from the web and mobile application domains are targets of our study

Uma abordagem sistemática para implementação, gerenciamento e customização de testes de linhas de produto de software

Through the adoption of the software product line (SPL) approach, several benefits are achieved when compared to the conventional development processes that are based on creating a single software system at a time. The process of developing a SPL differs from traditional software construction, since it has two essential phases: the domain engineering - when common and variables elements of the SPL are defined and implemented; and the application engineering - when one or more applications (specific products) are derived from the reuse of artifacts created in the domain engineering. The test activity is also fundamental and aims to detect defects in the artifacts produced in SPL development. However, the characteristics of an SPL bring new challenges to this activity that must be considered. Several approaches have been recently proposed for the testing process of product lines, but they have been shown limited and have only provided general guidelines. In addition, there is also a lack of tools to support the variability management and customization of automated case tests for SPLs. In this context, this dissertation has the goal of proposing a systematic approach to software product line testing. The approach offers: (i) automated SPL test strategies to be applied in the domain and application engineering, (ii) explicit guidelines to support the implementation and reuse of automated test cases at the unit, integration and system levels in domain and application engineering; and (iii) tooling support for automating the variability management and customization of test cases. The approach is evaluated through its application in a software product line for web systems. The results of this work have shown that the proposed approach can help the developers to deal with the challenges imposed by the characteristics of SPLs during the testing process

Squid impact analyser: uma ferramenta para análise de impacto de mudança em linhas de produto de software

Software Products Lines (SPL) is a software engineering approach to developing software system families that share common features and differ in other features according to the requested software systems. The adoption of the SPL approach can promote several benefits such as cost reduction, product quality, productivity, and time to market. On the other hand, the SPL approach brings new challenges to the software evolution that must be considered. Recent research work has explored and proposed automated approaches based on code analysis and traceability techniques for change impact analysis in the context of SPL development. There are existing limitations concerning these approaches such as the customization of the analysis functionalities to address different strategies for change impact analysis, and the change impact analysis of fine-grained variability. This dissertation proposes a change impact analysis tool for SPL development, called Squid Impact Analyzer. The tool allows the implementation of change impact analysis based on information from variability modeling, mapping of variability to code assets, and existing dependency relationships between code assets. An assessment of the tool is conducted through an experiment that compare the change impact analysis results provided by the tool with real changes applied to several evolution releases from a SPL for media management in mobile devices

Aplicação do método B ao projeto formal de software embarcado

This work shows a project method proposed to design and build software components from the software functional m del up to assembly code level in a rigorous fashion. This method is based on the B method, which was developed with support and interest of British Petroleum (BP). One goal of this methodology is to contribute to solve an important problem, known as The Verifying Compiler. Besides, this work describes a formal model of Z80 microcontroller and a real system of petroleum area. To achieve this goal, the formal model of Z80 was developed and documented, as it is one key component for the verification upto the assembly level. In order to improve the mentioned methodology, it was applied on a petroleum production test system, which is presented in this work. Part of this technique is performed manually. However, almost of these activities can be automated by a specific compiler. To build such compiler, the formal modelling of microcontroller and modelling of production test system should provide relevant knowledge and experiences to the design of a new compiler. In ummary, this work should improve the viability of one of the most stringent criteria for formal verification: speeding up the verification process, reducing design time and increasing the quality and reliability of the product of the final software. All these qualities are very important for systems that involve serious risks or in need of a high confidence, which is very common in the petroleum industry

Design of a state observer using decay rate LMI constraints for fault detection in mechanical systems

Nowadays, one of the most important concerns for many companies is to maintain the operation of their systems without sudden equipment break down. Because of this, new techniques for fault detection and location in mechanical systems subject to dynamic loads have been developed. This paper studies of the influence of the decay rate in the design of state observers using LMI for fault detection in mechanical systems. This influence is analyzed by the performance index proposed by Huh and Stein for the condition of a state observer. An example is presented to illustrate the methodology discussed.

Utilização de água residuária do processo pós-colheita do café na produção de mudas de cafeeiro

Intending to achieve better results on coffee production, the coffee producers began, since the 80s, to process the coffee postharvest, in order to ensure product's superior quality. However, with the processing, other problem appeared, the contamination of rivers, creeks, soil and water table from coffee wastewater (ARC). This paper had as main objective to use the ARC on the coffee plants' production verifying its viability and if the ARC is able to supply the coffee potassium requirements when they don't receive potassium chloride in the organic compound. The work was developed at Faculdade de Ciências Agronômicas - UNESP, Botucatu-SP, in a greenhouse located at Departamento de Engenharia Rural. The work consisted of 10 treatments on a 5×2 factorial (5 wastewater proportions of coffee after the harvest processing - 0%, 25%, 50%, 75% and 100% - and potassium chloride presence or absence in the composition), with 4 repetitions with a completely randomized statistical design. The ARC was applied each 48 hours in an irrigation depth of 10 mm. After 6 months, the plants' vegetative characteristic had been evaluated as well the chemical characteristics of the compound and of the plants. We observed that the treatments with potassium chloride presence showed worse vegetative characteristics compared with treatments which did not have KCl in its composition. Moreover, with the increase of the wastewater dosage, it happened a decrease in the vegetative characteristics, however an addition in the chemical characteristics of the compound. Also, the treatments without KCl presence and with 0% and 25% of coffee wastewater had been statistically equal, showing the viability in the use of the ARC in the production of coffee plants, since the compound does not contain KCl and that the water used in the composition is a mixture of 25% of ARC with 75% of common water.