Aqueous-phase reforming of renewables for selective hydrogen production in the presence of supported platinum catalysts

The evolution of our society is impossible without a constant progress in life-important areas such as chemical engineering and technology. Innovation, creativity and technology are three main components driving the progress of chemistry further towards a sustainable society. Biomass, being an attractive renewable feedstock for production of fine chemicals, energy-rich materials and even transportation fuels, captures progressively new positions in the area of chemical technology. Knowledge of heterogeneous catalysis and chemical technology applied to transformation of biomass-derived substances will open doors for a sustainable economy and facilitates the discovery of novel environmentally-benign processes which probably will replace existing technologies in the era of biorefinary. Aqueous-phase reforming (APR) is regarded as a promising technology for production of hydrogen and liquids fuels from biomass-derived substances such as C3-C6 polyols. In the present work, aqueous-phase reforming of glycerol, xylitol and sorbitol was investigated in the presence of supported Pt catalysts. The catalysts were deposited on different support materials, including Al2O3, TiO2 and carbons. Catalytic measurements were performed in a laboratory-scale continuous fixedbed reactor. An advanced analytical approach was developed in order to identify reaction products and reaction intermediates in the APR of polyols. The influence of the substrate structure on the product formation and selectivity in the APR reaction was also investigated, showing that the yields of the desired products varied depending on the substrate chain length. Additionally, the influence of bioethanol additive in the APR of glycerol and sorbitol was studied. A reaction network was advanced explaining the formation of products and key intermediates. The structure sensitivity in the aqueous-phase reforming reaction was demonstrated using a series of platinum catalysts supported on carbon with different Pt cluster sizes in the continuous fixed-bed reactor. Furthermore, a correlation between texture physico-chemical properties of the catalysts and catalytic data was established. The effect of the second metal (Re, Cu) addition to Pt catalysts was investigated in the APR of xylitol showing a superior hydrocarbon formation on PtRe bimetallic catalysts compared to monometallic Pt. On the basis of the experimental data obtained, mathematical modeling of the reaction kinetics was performed. The developed model was proven to successfully describe experimental data on APR of sorbitol with good accuracy.

Ristikkorakenteisen hihnakuljetinsillan mitoitustyökalun kehittäminen

Hihnakuljettimia käytetään muun muassa voimalaitos- ja sellutehdasympäristöissä kuljettamaan kiinteää polttoainetta tai haketta pitkiä matkoja. Pitkät hihnakuljettimet asennetaan yleensä teräsristikoista rakennettujen kuljetinsiltojen sisään. Kuljetinsilta toimii siis hihnakuljettimen ja hoitokäytävän runkona sekä suojaa kuljetinta ja kuljetettavaa materiaalia säältä. Tässä diplomityössä on laadittu mitoitustyökalu, jolla voidaan nopeasti mitoittaa ristikkorakenteisen hihnakuljetinsillan sauvat sekä määrittää rakenteen massa. Laskentaohjelma on toteutettu Microsoft Excel -taulukkolaskentana. Sillan poikkileikkaus voi olla suljettu symmetrinen umpirakenne tai avorakenne, jossa on ulokkeellinen hoitotaso. Ristikon sauvat ovat RHS-putkia. Rakenteeseen voi vaikuttaa jatkuvia kuormia, pistekuormia sekä näistä johdetut, ekvivalenttiin staattiseen voimaan perustuvat maanjäristyskuormat. Diplomityössä on perehdytty mitoitustyökalussa sovellettuihin teorioihin. Voimasuureiden laskenta perustuu 2-tukisina palkkeina käsiteltävien siltalohkojen ratkaisuun ja palkkianalogiaan, jossa ristikon sauvavoimat ratkaistaan käsittelemällä ristikkoa palkkina. Sauvojen kestävyyden laskenta perustuu SFS-EN 1993-1-1 -normiin, joka on osa Eurocode -rakennesuunnittelunormistoa. Lisäksi työssä on käsitelty ristikkoliitosten mitoitusta SFS-EN 1993-1-8 mukaan. Mitoitusohjelman toimivuutta on testattu tarkastelemalla esimerkkisiltaa laaditulla mitoituspohjalla ja Autodesk Robot Professional 2013 -FE-analyysiohjelmisuolla. Tulosten perusteella mitoitustyökalua voidaan käyttää ainakin tarjousvaiheen nopeisiin tarkasteluihin ja omamassan määritykseen, mutta myös lopulliseen mitoitukseen, mikäli hyväksytään konservatiivinen mitoitus.

Catalytic upgrading of biomass extractives to fine chemicals over supported ionic liquid catalysts (SILCAs)

Behovet av förnyelsebar energi ökar ständigt eftersom det finns en strävan att minska beroendet av fossila bränslen. Dessutom är tillgångar av fossila bränslen begränsade. Miljövänliga processer för bioraffinaderier erbjuder en stor möjlighet för produktion av energi, bränslen och kemikalier. Den finska och svenska skogsindustrin har en lång tradition i utnyttjandet av skogsbiomassor. Bioraffinaderier som integreras med pappers- och cellulosaindustrin kan frambringa både ekonomiska och ekologiska fördelar i framställning av traditionella och biobaserade produkter. I doktorsarbetet studerades omvandling av extraktivämnen till finkemikalier som kan användas t.ex. av läkemedelsindustrin. Extraktivämnen fås ur biomassa. I forskningsarbetet framställdes biobaserade finkemikalier med hjälp av katalysatorer som baserar sig på joniska vätskor. Biomassan består av cellulosa, hemicellulosa, lignin och extraktivämnen, vilka huvudsakligen är terpener, vaxer och fettsyror. Extraktivämen är vedens komponenter, som kan separeras ur vedmaterialet med hjälp av neutrala lösningsmedel. Joniska vätskekatalysatorer som var immobiliserade på fasta bärare utnyttjades för isomerisering av α,β-pinenoxider samt hydrogenering citral. Inverkan av joniska vätskor på katalysatorns aktivitet och reaktionernas produktfördelning undersöktes under varierande reaktionsbetingelser. Kinetiska modeller för pinenoxidens isomeriseringsreaktioner beskrev väl experimentellt upptäckta skillnader mellan olika katalysatorer. --------------------------------------------------- Uusiutuvan energian tarve on kasvussa, koska riippuvuutta fossiilisista polttoaineista pyritään vähentämään. Tämän lisäksi fossiilisten polttoaineiden varannot ovat rajalliset. Ympäristöystävälliset biojalostusprosessit ovat näin ollen suuri mahdollisuus energian, polttoaineiden ja kemikaalien tuotannossa. Suomen ja Ruotsin metsäteollisuudella on pitkät perinteet metsäbiomassojen hyödyntämisessä. Paperi- ja selluteollisuuden yhteyteen integroiduilla biojalostamoilla voidaan luoda taloudellisia ja ympäristöllisiä etuja sekä perinteisten että biopohjaisten tuotteiden valmistuksessa. Väitöstyössä on tutkittu biomassan uuteaineiden kemiallista muuntamista hienokemikaaleiksi, joita voidaan käyttää esimerkiksi lääkeaineteollisuudessa. Biopohjaisia hienokemikaaleja on valmistettu biomassan uuteaineista ionisiin nesteisiin perustuvilla katalyyteillä. Biomassa koostuu selluloosasta, hemiselluloosasta, ligniinistä sekä uuteaineista, jotka ovat pääosin terpeenejä, vahoja tai rasvahappoja. Uuteaineet ovat puun komponentteja, jotka voidaan erottaa puusta neutraalien liuottimien avulla. Kiinteän kantajan päälle immobilisoituja ionisia nestekatalyyttejä (Supported Ionic Liquid Catalyst) hyödynnettiin α,β-pineenioksidien isomerisointireaktioissa sekä sitraalin vedytysreaktioissa. Ionisten nesteiden vaikutusta katalyyttien aktiivisuuteen sekä reaktioiden tuotejakaumaan tutkittiin erilaisissa reaktio-olosuhteissa. Pineenioksidien isomerisointireaktioiden kineettiset mallit kuvasivat hyvin kokeellisesti todettuja katalyyttien eroavaisuuksia.

Measurement of epidermal thickness in a patient with psoriasis by computer-supported image analysis

The aim of the present study was to measure full epidermal thickness, stratum corneum thickness, rete length, dermal papilla widening and suprapapillary epidermal thickness in psoriasis patients using a light microscope and computer-supported image analysis. The data obtained were analyzed in terms of patient age, type of psoriasis, total body surface area involvement, scalp and nail involvement, duration of psoriasis, and family history of the disease. The study was conducted on 64 patients and 57 controls whose skin biopsies were examined by light microscopy. The acquired microscopic images were transferred to a computer and measurements were made using image analysis. The skin biopsies, taken from different body areas, were examined for different parameters such as epidermal, corneal and suprapapillary epidermal thickness. The most prominent increase in thickness was detected in the palmar region. Corneal thickness was more pronounced in patients with scalp involvement than in patients without scalp involvement (t = -2.651, P = 0.008). The most prominent increase in rete length was observed in the knees (median: 491 µm, t = 10.117, P = 0.000). The difference in rete length between patients with a positive and a negative family history was significant (t = -3.334, P = 0.03), being 27% greater in psoriasis patients without a family history. The differences in dermal papilla distances among patients were very small. We conclude that microscope-supported thickness measurements provide objective results.

Transformation of carbon dioxide to diethyl carbonate over ceria and ceria-supported catalysts

Carbon dioxide is regarded, nowadays, as a primary anthropogenic greenhouse gas leading to global warming. Hence, chemical fixation of CO2 has attracted much attention as a possible way to manufacture useful chemicals. One of the most interesting approaches of CO2 transformations is the synthesis of organic carbonates. Since conventional production technologies of these compounds involve poisonous phosgene and carbon monoxide, there is a need to develop novel synthetic methods that would better match the principles of "Green Chemistry" towards protection of the environment and human health. Over the years, synthesis of dimethyl carbonate was under intensive investigation in the academia and industry. Therefore, this study was entirely directed towards equally important homologue of carbonic esters family namely diethyl carbonate (DEC). Novel synthesis method of DEC starting from ethanol and CO2 over heterogeneous catalysts based on ceria (CeO2) was studied in the batch reactor. However, the plausible drawback of the reaction is thermodynamic limitations. The calculated values revealed that the reaction is exothermic (ΔrHØ298K = ─ 16.6 J/ ) and does not occur spontaneously at rooms temperature (ΔrGØ 298K = 35.85 kJ/mol). Moreover, co-produced water easily shifts the reaction equilibrium towards reactants excluding achievement of high yields of the carbonate. Therefore, in-situ dehydration has been applied using butylene oxide as a chemical water trap. A 9-fold enhancement in the amount of DEC was observed upon introduction of butylene oxide to the reaction media in comparison to the synthetic method without any water removal. This result confirms that reaction equilibrium was shifted in favour of the desired product and thermodynamic boundaries of the reaction were suppressed by using butylene oxide as a water scavenger. In order to obtain insight into the reaction network, the kinetic experiments were performed over commercial cerium oxide. On the basis of the selectivity/conversion profile it could be concluded that the one-pot synthesis of diethyl carbonate from ethanol, CO2 and butylene oxide occurs via a consecutive route involving cyclic carbonate as an intermediate. Since commercial cerium oxide suffers from the deactivation problems already after first reaction cycle, in-house CeO2 was prepared applying room temperature precipitation technique. Variation of the synthesis parameters such as synthesis time, calcination temperature and pH of the reaction solution turned to have considerable influence on the physico-chemical and catalytic properties of CeO2. The increase of the synthesis time resulted in high specific surface area of cerium oxide and catalyst prepared within 50 h exhibited the highest amount of basic sites on its surface. Furthermore, synthesis under pH 11 yielded cerium oxide with the highest specific surface area, 139 m2/g, among all prepared catalysts. Moreover, CeO2─pH11 catalyst demonstrated the best catalytic activity and 2 mmol of DEC was produced at 180 oC and 9 MPa of the final reaction pressure. In addition, ceria-supported onto high specific surface area silicas MCM-41, SBA-15 and silica gel were synthesized and tested for the first time as catalysts in the synthesis of DEC. Deposition of cerium oxide on MCM-41 and SiO2 supports resulted in a substantial increase of the alkalinity of the carrier materials. Hexagonal SBA-15 modified with 20 wt % of ceria exhibited the second highest basicity in the series of supported catalysts. Evaluation of the catalytic activity of ceria-supported catalysts showed that reaction carried out over 20 wt % CeO2-SBA-15 generated the highest amount of DEC.

The influence of high cable penetration in distribution networks on earth fault currents and the operation of relay protection.

Recent Storms in Nordic countries were a reason of long power outages in huge territories. After these disasters distribution networks' operators faced with a problem how to provide adequate quality of supply in such situation. The decision of utilization cable lines rather than overhead lines were made, which brings new features to distribution networks. The main idea of this work is a complex analysis of medium voltage distribution networks with long cable lines. High value of cable’s specific capacitance and length of lines determine such problems as: high values of earth fault currents, excessive amount of reactive power flow from distribution to transmission network, possibility of a high voltage level at the receiving end of cable feeders. However the core tasks was to estimate functional ability of the earth fault protection and the possibility to utilize simplified formulas for operating setting calculations in this network. In order to provide justify solution or evaluation of mentioned above problems corresponding calculations were made and in order to analyze behavior of relay protection principles PSCAD model of the examined network have been created. Evaluation of the voltage rise in the end of a cable line have educed absence of a dangerous increase in a voltage level, while excessive value of reactive power can be a reason of final penalty according to the Finish regulations. It was proved and calculated that for this networks compensation of earth fault currents should be implemented. In PSCAD models of the electrical grid with isolated neutral, central compensation and hybrid compensation were created. For the network with hybrid compensation methodology which allows to select number and rated power of distributed arc suppression coils have been offered. Based on the obtained results from experiments it was determined that in order to guarantee selective and reliable operation of the relay protection should be utilized hybrid compensation with connection of high-ohmic resistor. Directional and admittance based relay protection were tested under these conditions and advantageous of the novel protection were revealed. However, for electrical grids with extensive cabling necessity of a complex approach to the relay protection were explained and illustrated. Thus, in order to organize reliable earth fault protection is recommended to utilize both intermittent and conventional relay protection with operational settings calculated by the use of simplified formulas.

FT-IR and MAS NMR analysis of montmorillonite K10 supported MF2 reagents and their activity as catalysis /

ZnF2, CdF2, and CUF2 have been adsorbed onto the surface of montmorillonite K10, and the infrared and 19F, 27 AI, and 29Si MAS NMR spectra of the reagents over a range of loadings have been obtained. CUF2 was observed to attack the Si02 layer and form the complex CuSiF6, Zn F2 tends to attack the aluminium oxide layer, in which Zn isomorphously replaces AI, and forms AIF3 and AIF4 - complexes. All the spectroscopic evidence ruled out the formation of any AI-F and/or Si-F free species as CdF2 is adsorbed on the surface of montmorillonite K10. The reactivity of MF2-K10 reagents towards Friedel-Crafts benzylation of benzene with benzyl chloride varied from one reagent to another. ZnF2-K10 was observed to be the most reactive and CUF2 was the least reactive.

Sol-gel routes to supported Friedel-Crafts alkylation catalysts

Aluminosilicate catalysts containing supported ZnCl2 and metal fluoride salts have been prepared using a sol-gel based route, tested and characterized. The activities of these ZnCl2 + metal fluoride catalysts, while greater than "Clayzic" (ZnCI2 supported on montmorillonite KIO) are not as good as supported ZnCl2 only supported on aluminosilicate. Alumina supports have also been prepared via a sol-gel route using various chemical additives to generate a mesoporous structure, loaded with ZnCl2 and tested for activity. The activities for these alumina-supported catalysts are also significantly higher than that of "Clayzic", an effective Friedel-Crafts catalyst. Characterizations of these two types of catalysts were done by magic angle spinning (MAS) NMR, diffuse reflectance infrared (DRIFT) spectroscopy and additionally for the alumina nitrogen adsorption studies were done. Supported aluminum trichloride was also investigated as an alternative to the traditional use of aluminum trichloride.

Clinician-Perceived Bridges and Barriers to Parental Implementation of Picture Exchange Communication System (PECS): An evaluation.

Picture Exchange Communication System (PECS) is an augmentative and alternative communicative system that improves communication and decreases problem behaviors in children with Developmental Disabilities and Autism. The mediator model is a validated approach that clinicians use to train parents to perform evidence-based interventions. Parental non-adherence to treatment recommendations is a documented problem. This qualitative study investigated clinician-perceived factors that influence parental adherence to PECS recommendations. Three focus groups (n=8) were conducted with Speech Language Pathologists and Behavior Therapists experienced in providing parents with PECS recommendations. Constant comparison analysis was used. In general, clinicians believed that PECS was complex to implement. Thirty-one bridges were identified to overcome complexity. Twenty-two barriers and 6 other factors also impacted parental adherence. Strategies to address these factors were proposed based on a review of the literature. Future research will be performed to validate these findings using parents and a larger sample size.

Andrew Bloomfield collection, 2006-2012

Andrew Bloomfield, and his twin sister Victoria, were born on May 6, 1968 in Auckland, New Zealand. The following year, the family moved to Guelph, Ontario. It became apparent from the time Andrew was 14 months old that he differed considerably from his twin sister, and he was subsequently diagnosed with autism when he was four years old. As a result, he lived away from his family for much of his early life in order to participate in programs for autistic people. Andrew found this very difficult, but also made some significant progress. He became able to relate to and care for his dog, and was able to express his thoughts with Augmentative and Alternative Communication, especially using Supported Typing. His twin sister Victoria was an important person in his life, and her untimely death in a car accident in 1996 devastated him. However, his network of friends and family have provided immense support and helped him build a fulfilling and meaningful life. In 2004 Andrew founded a group of other adult communicators who "type to talk" which he named "Bridges-Over-Barriers". They meet monthly in Guelph and contributed to the 2010 volume with accompanying documentary film on DVD. He lives in his own home in Guelph, guaranteed by a housing trust, and has written several books, including an autobiography, Bridges over Barriers in My Life with Autism.

Chart of bill of timber in bridges, culverts, cattle-guard and roadways, signed by S.D. Woodruff

Chart of bill of timber in bridges, culverts, cattle-guard and roadways, signed by S.D. Woodruff, Oct. 18, 1855.

Cable to L.C.O. Woodruff from Mona Foster

Cable to L.C.O. Woodruff from Mona Foster. She asks if she should sell the securities and invest in war loans, n.d.

Proyecto técnico - económico para implementar un sistema de televisión por cable (CATV) en la ciudad de Trujillo-Perú

Tesis (Maestría en Ciencias de la Administración en Especialidaden Finanzas) UANL