A solid-phase microextraction fiber coated with diglycidyloxycalix[4]arene yields very high extraction selectivity and sensitivity during the analysis of chlorobenzenes in soil

A novel fiber coated with novel sol-gel (5,11,17,23-tetra-tert-butyl-25,27-dihydroxy-26,28-diglycidyloxycalix[4]arene/hydroxy-terminated silicone oil; diglycidyloxy-C[4]/OH-TSO) was prepared for use with headspace solid-phase microextraction (HS-SPME) combined with gas chromatography (GC) and electron capture detection (ECD), which was applied in order to determine nine chlorobenzenes in soil matrices. Due to the improved fiber preparation, which increases the percentage of calixarene in the coating, the new calixarene fiber exhibits very high extraction selectivity and sensitivity to chlorine-substituted compounds. Various parameters affecting the extraction efficiency were optimized in order to maximize the sensitivity during the chlorobenzene analysis. Interferences from different soil matrices with different characteristics were investigated, and the amount extracted was strongly influenced by the matrix. Therefore, a standard addition protocol was performed on the real soil samples. The linear ranges of detection for the chlorobenzenes tested covered three orders of magnitude, and correlation coefficients > 0.9976 and relative standard deviations (RSD) < 8% were observed. The detection limits were found at sub-ng/g of soil levels, which were about an order of magnitude lower than those given by the commercial poly(dimethylsiloxane) (PDMS) coating for most of the compounds. The recoveries ranged from 64 to 109.6% for each analyte in the real kaleyard soil matrix when different concentration levels were determined over the linear range, which confirmed the reliability and feasibility of the HS-SPME/GC-ECD approach using the fiber coated with diglycidyloxy-C[4]/OH-TSO for the ultratrace analysis of chlorobenzenes in complex matrices.

Two unisexual artificial polyploid clones constructed by genome addition of common carp (Cyprinus carp) and crucian carp (Carassius auratus)

A polyploid hybrid fish with natural gynogenesis can prevent segregation and maintain their hybrid vigor in their progenies. Supposing the reproduction mode of induced polyploid fish being natural gynogenesis, allopolyploid hybrid between common carp and crucian carp into allopolyploid was performed. The purpose of this paper is to describe a lineage from sexual diploid carp transforming into allotriploid and allotetraploid unisexual clones by genome addition. The diploid hybrid between common carp and crucian carp reproduces an unreduced nucleus consisting of two parental genomes. This unreduced female pronucleus will fuse with male pronucleus and form allotriploid zygote after penetration of related species sperms. Allotriploid embryos grow normally, and part of female allotriploid can produce unreduced mature ova with three genomes. Mature ova of most allotriploid females are provided with natural gynogenetic trait and their nuclei do not fuse with any entrance sperm. All female offspring are produced by gynogenesis of allotriploid egg under activation of penetrating sperms. These offspring maintain morphological traits of their allotriploid maternal and form an allotetraploid unisexual clone by gynogenetic reproduction mode. However, female nuclei of rare allotriploid female can fuse with penetrating male pronuclei and result in the appearance of allotetraploid individuals by means of genome addition. All allotetraploid females can reproduce unreduced mature eggs containing four genomes. Therefore, mature eggs of allotetraploid maintain gynogenetic trait and allotetraploid unisexual clone is produced under activation of related species sperms.

In-situ synthesis of AlN powders and composite AlN powders with yttrium addition

Using Al-Mg and Al-Mg-Y alloys as raw materials and nitrogen as gas reactants, AIN powders and composite AIN powders by in-situ synthesis method were prepared. AIN lumps prepared by the nitriding of Al-Mg and Al-Mg-Y alloys have porous microstructure, which is favorable for pulverization. They have high purity, containing 1.23 % (mass fraction) oxygen impurity, and consisted of AIN single phase . The average particle size of AIN powders is 6.78 mum. Composite AlN powders consist of AlN phases and rare, earth oxide Y2O3 phase. The distribution of particle size of AIN powders shows two peaks. In view, of packing factor, AIN powders with such size distribution can easily be sintered to high density.

Performing Fast Addition and Multiplication by Transferring Single Electrons

This paper proposes novel fast addition and multiplication circuits that are based on non-binary redundant number systems and single electron (SE) devices. The circuits consist of MOSFET-based single-electron (SE) turnstiles. We use the number of electrons to represent discrete multiple-valued logic states and we finish arithmetic operations by controlling the number of electrons transferred. We construct a compact PD2,3 adder and a 12x12bit multiplier using the PD2,3 adder. The speed of the adder can be as high as 600MHz with 400nW power dissipation. The speed of the adder is regardless of its operand length. The proposed circuits have much smaller transistors than conventional circuits.

Effect of Ru addition to CO/SiO2/HZSM-5 catalysts on Fischer-Tropsch synthesis of gasoline-range hydrocarbons

Microporous HZSM-5 zeolite and mesoporous SiO2 supported Ru-Co catalysts of various Ru adding amounts were prepared and evaluated for Fischer-Tropsch synthesis (FTS) of gasoline-range hydrocarbons (C-5-C-12). The tailor-made Ru-Co/SiO2/HZSM-5 catalysts possessed both micro- and mesopores, which accelerated hydrocracking/hydroisomerization of long-chain products and provided quick mass transfer channels respectively during FTS. In the same time. Ru increased Cor reduction degree by hydrogen spillover, thus CO conversion of 62.8% and gasoline-range hydrocarbon selectivity of 47%, including more than 14% isoparaffins, were achieved simultaneously when Ru content was optimized at 1 wt% in Ru-Co/SiO2/HZSM-5 catalyst.

Methanol synthesis from CO2 using a silicone rubber/ceramic composite membrane reactor

A one-dimensional isothermal pseudo-homogeneous parallel flow model was developed for the methanol synthesis from CO2 in a silicone rubber/ceramic composite membrane reactor. The fourth-order Runge-Kutta method was adopted to simulate the process behaviors in the membrane reactor. How those parameters affect the reaction behaviors in the membrane reactor, such as Damkohler number Da, pressure ratio p(r), reaction temperature T, membrane separation factor alpha, membrane permeation parameter phi , as well as the non-uniform parameter of membrane permeation L-1, were discussed in detail. Parts of the theoretical results were tested and verified; the experimental results showed that the conversion of the main reaction in the membrane reactor increased by 22% against traditional fixed bed reactor, and the optimal non-uniform parameter of membrane permeation rate, L-1.opt ,does exist. (C) 2003 Elsevier B.V All rights reserved.

Computational study on the addition of HCN to methanimine catalyzed by formamidine and formamide

In this paper, we have carried out a theoretical study on the addition of HCN to methanimine with formamidine or formamide using second-order Moller-Plesset perturbation (MP2) method with 6-31 + G(d,p) basis sets. At MP2 level. a high-energy, intermediate has been located for each pathway. The addition of HCN to methanimine with formamidine has the lowest free energy barrier according to the calculations at MP2 level. (C) 2004 Elsevier B.V. All rights reserved.