Preparation and characterisation of refractory whiskers and selected alumina composites

A whisker is a common name of single crystalline inorganic fibre of small dimensions, typically 0.5-1 μm in diameter and 20-50 μm in length. Whiskers are mainly used as reinforcement of ceramics. This work describes the synthesis and characterisation of new whisker types. Ti0.33Ta0.33Nb0.33CxN1-x, TiB2, B4C, and LaxCe1-xB6 have been prepared by carbothermal vapour–liquid–solid (CTR-VLS) growth mechanisms in the temperature range 900-1800°C, in argon or nitrogen. Generally, carbon and different suitable oxides were used as whisker precursors. The oxides reacted via a carbothermal reduction process. A halogenide salt was added to form gaseous metal halogenides or oxohalogenides and small amount of a transition metal was added to catalyse the whisker growth. In this mechanism, the whisker constituents are dissolved into the catalyst, in liquid phase, which becomes supersaturated. Then a whisker could nucleate and grow out under continuous feed of constituents. The syntheses of TiC, TiB2, and B4C were followed at ordinary synthesis conditions by means of mass spectrometry (MS), thermogravimetry (TG), differential thermal analysis (DTA) and quenching. The main reaction starting temperatures and reaction time for the different mixtures was revealed, and it was found that the temperature inside the crucible during the reactions was up to 100°C below the furnace set-point, due to endothermic nature of the reactions. Quench experiments showed that whiskers were formed already when reaching the temperature plateau, but the yield increased fast with the holding time and reached a maximum after about 20-30 minutes. Growth models for whisker formation have been proposed. Alumina based composites reinforced by (2-5 vol.%) TiCnano and TiNnano and 25 vol.% of carbide, and boride phases (whiskers and particulates of TiC, TiN, TaC, NbC, (Ti,Ta)C, (Ti,Ta,Nb)C, SiC, TiB2 and B4C) have been prepared by a developed aqueous colloidal processing route followed by hot pressing for 90 min at 1700°C, 28 MPa or SPS sintering for 5 minutes at 1200-1600°C and 75 MPa. Vickers indentation measurements showed that the lowest possible sintering temperature is to prefer from mechanical properties point of view. In the TiNnano composites the fracture mode was typically intergranular, while it was transgranular in the SiCnano composites. The whisker and particulate composites have been compared in terms of e.g. microstructure and mechanical properties. Generally, additions of whiskers yielded higher fracture toughness compared to particulates. Composites of commercially available SiC whiskers showed best mechanical properties with a low spread but all the other whisker phases, especially TiB2, exhibited a great potential as reinforcement materials.

Problemi di diagnostica e restauro dei materiali decorativi nell'architettura Liberty in Emilia-Romagna

Le pietre artificiali ed i cementi artistici utilizzati durante la stagione Liberty rappresentano tutt’oggi un patrimonio artistico non ancora sufficientemente studiato. In seguito ad una ricerca bibliografica su testi e riviste dei primi anni del Novecento, è stata eseguita una ricognizione del patrimonio architettonico emiliano-romagnolo, al fine di valutarne i materiali e le tipologie di degrado più diffuse. Le città e le zone oggetto di studio sono state: Bologna, Ferrara, Modena e provincia, Reggio Emilia, Parma, Firenze, la Romagna e le Marche settentrionali. Tra gli edifici individuati sono state analizzate le decorazioni e gli intonaci di tre edifici ritenuti particolarmente significativi: il villino Pennazzi (noto anche come Villa Gina) a Borgo Panigale (Bologna), villa Verde a Bologna e l’ex-albergo Dorando Pietri a Carpi. Da tali edifici sono stati selezionati campioni rappresentativi delle diverse tipologie di decorazioni in pietra artificiale e successivamente sono stati caratterizzati in laboratorio tramite diffrattometria a raggi x (XRD), termogravimetria (TGA), microscopio ottico in sezioni lucide, microscopio elettronico a scansione (SEM) e porosimetria ad intrusione di mercurio (MIP). In particolare per Villa Verde sono state formulate e caratterizzate diverse tipologie di malte variando il tipo di legante ed il rapporto acqua/cemento, al fine di garantire la compatibilità fisico-meccanica con il supporto negli interventi di risarcimento delle lacune previsti nel restauro. L’attività sperimentale svolta ha permesso di mettere a punto un vero e proprio protocollo diagnostico per il restauro di questo tipo di decorazioni che potrà essere utilizzato sia nei casi di studio analizzati che per ogni futuro intervento.

Experimental determination of the eutectic temperature in air of the CuO-TiO2 pseudobinary system

Eutectic temperature and composition in the CuO–TiO2 pseudobinary system have been experimentally determined in air by means differential thermal analysis (DTA), thermogravimetry (TG) and hot-stage microscopy (HSM). Samples of the new eutectic composition treated at different temperatures have been characterized by X-ray diffraction (XRD) and X-ray absorption near-edge structural spectroscopy (XANES) to identify phases and to determine the Cu valence state, respectively. The results show that the eutectic temperature in air is higher by 100 °C (∼1000 °C) for a Ti-richer composition (XTiO2=25 mol%) than the one calculated in the literature. The reduction of Cu2+ to Cu+ takes places at about 1030 °C. The existence of Cu2TiO3 and Cu3TiO4 has been confirmed by XRD in the temperature range between 1045 and 1200 °C.

Obtenção de gel mucoadesivo de nistatina para o tratamento da candidíase oral. Desenvolvimento e caracterização de dispersões sólidas de nistatina

A nistatina (NYS) é o fármaco de primeira escolha no tratamento da candidíase oral, que frequentemente acomete mais os indivíduos imunocomprometidos e pacientes com outras desordens (diabetes não tratada, neoplasias, imunodeficiências). No mercado brasileiro, a NYS é encontrada na forma de suspensão oral aquosa, onde o procedimento para sua administração consiste em bochechar o medicamento. Apesar de haver a indicação de que se mantenha o contato direto entre fármaco e a mucosa oral, na qual se encontra a Candida spp., o que aumentaria expressivamente o sucesso terapêutico, a suspensão não apresenta tal propriedade. Assim, a NYS que é fármaco com ação efetiva contra a candidíase oral, é considerada pertencente à Classe IV do Sistema de Classificação Biofarmacêutica, ou seja, apresenta baixa solubilidade e baixa permeabilidade. A baixa solubilidade pode comprometer sua disponibilidade na cavidade oral, e consequentemente, sua ação farmacológica. Diante desse quadro, o objetivo do presente trabalho foi o desenvolvimento de dispersões sólidas de NYS para o tratamento da candidíase oral, e sua posterior incorporação em gel mucoadesivo oral, favorecendo a formulação no local de ação. As dispersões sólidas são sistemas farmacêuticos, onde um fármaco pouco solúvel em água encontra-se dispersado em um carreador, no estado sólido. Os carreadores normalmente são hidrofílicos, o que permite que esses sistemas sejam empregados para aumentar a solubilidade aquosa do fármaco. Assim, foram desenvolvidas as dispersões sólidas de NYS, pelo método de eliminação do solvente, empregando como carreadores, lactose, HPMC, poloxamer 407 e poloxamer 188. Essas foram submetidas à caracterização por análise térmica, usando os ensaios de calorimetria exploratória diferencial (DSC) e termogravimetria/termogravimetria derivada (TG/DTG). Dentre essas dispersões sólidas, aquelas que se mostraram com comportamento térmico sugerindo a formação de um novo \"sistema\", foram analisadas por meio de ensaio de solubilidade. Dessa forma, a formulação NYS DS G2 (49) se destacou, pois apresentou maior solubilidade em água (4,484 mg/mL); em pH 5,5 (4,249 mg/mL) e em pH 7,0 (4,293 mg/mL), ou seja, houve um aumento de 1,426 vezes em água; 4,227 vezes em pH 5,5; e 2,743 vezes em pH 7,0. Essa formulação foi, por fim avaliada por difração de raio-X e espectroscopia de infravermelho com transformada de Fourier, técnicas que corroboraram com a análise térmica quanto à indicação de formação da dispersão sólida. Por sua vez, essa dispersão sólida foi incorporada em 4 bases de géis mucoadesivos de carbopol ® 934 PNF, alterando apenas a concentração do polímero (0,5; 1,0; 1,5; 2,0 %p/p). Foi observado que a liberação de NYS DS G2 (49) foi superior, quando comparada à liberação de NYS MP a partir do gel, e através do ensaio de mucoadesão, percebeu-se que os géis desenvolvidos apresentaram propriedades mucoadesivas compatíveis com relatos na literatura, independentemente da quantidade de carbopol ® empregada. As características reológicas foram distintas, e foi observado que as formulações Gel A e Gel B, que possuem menor quantidade de polímero, tiverem um indicativo de comportamento de fluido newtoniano, diferente dos demais, o que pode não ser desejado para esse tipo de forma farmacêutica tópica e semi-sólida. Ao final desse trabalho, pode-se concluir que foi possível desenvolver um sistema farmacêutico na forma de dispersão sólida com maior solubilidade que a NYS pura, e sua incorporação em uma forma farmacêutica mucoadesiva, e que a liberação da NYS na forma DS foi muito superior que o fármaco na forma \"convencional\", o que permite que a NYS esteja mais disponível na cavidade oral, e também junto à mucosa bucal, o que levaria a efeito farmacológico mais efetivo do antifúngico.

Estudo de nanocompósitos formados por PLA e nanopartículas de celulose.

Devido à preocupação com o meio ambiente e o volume crescente de resíduos plástico em aterros sanitários, os polímeros biodegradáveis estão sendo estudados extensivamente. Um deles é o PLA. Apesar de possuir propriedades comparáveis a polímeros commodities e polímeros de engenharia, ainda é necessário melhorar certas características do PLA, como resistência ao impacto. Para isso, a nanocelulose (NC) pode ser usada sem alterações significativas na biodegradação polimérica. Este estudo teve como objetivo obter a nanocelulose, caracteriza-la e incorpora-la ao poli(ácido láctico) (PLA), assim como, estudar as propriedades térmicas, morfológicas e mecânicas do compósito obtido. A NC foi obtida por hidrólise ácida utilizando ácido fosfórico e posteriormente foi silanizada com três silanos distintos. As nanopartículas foram caracterizadas por Birrefringência, Microscopia Eletrônica de Transmissão (MET), Termogravimetria (TG), Potencial Zeta, Espectroscopia Vibracional de Absorção no Infravermelho com Transformada de Fourier (FTIR) e Difração de Raio X (DRX). Com as imagens obtidas pelo MET foi possível medir o tamanho das partículas de NC. E então obter a razão de aspecto de 82 e o limite de percolação de 1,1% em massa, confirmando a morfologia de nanofibra. De acordo as analises TG\'s, a presença de NC silanizada aumentou o início da degradação térmica. Os compósitos, contendo 3% em massa de NC, foram obtidos por fusão em câmara de mistura e moldados por injeção. Os compósitos foram caracterizados por FTIR, Cromatografia de Permeação em Gel (GPC), TG, Calorimetria Exploratória Diferencial (DSC), Microscopia Eletrônica de Varredura (MEV-FEG), Impacto e Tração. As análises dos compósitos mostraram que a NC atuou como agente de nucleação, facilitando a cristalização do PLA, além de a NC ter atuado como reforço na matriz polimérica melhorando as propriedades mecânicas.

Corn stover thermal decomposition in pyrolytic and oxidant atmosphere

The pyrolysis and combustion of corn stover were studied by dynamic thermogravimetry and derivate thermogravimetry (TG-DTG) at heating rates of 5, 10, 20 and 50 K min−1 at atmospheric pressure. For the simulation of pyrolysis and combustion processes a kinetic model based on the distribution of activation energies was used, with three pools of reactants (three pseudocomponents) because of the complexity of the biomass samples of agricultural origin. The experimental thermogravimetric data of pyrolysis and combustion processes were simultaneously fitted to determine a single set of kinetic parameters able to describe both processes at the different heating rates. The model proposed achieves a good correlation between the experimental and calculated curves, with an error of less than 4% for fitting four heating rates simultaneously. The experimental results and kinetic parameters may provide useful data for the design of thermo decomposition processing system using corn stover as feedstock. On the other hand, analysis of the main compounds in the evolved gas is given by means of a microcromatograph.

Studies on the thermal decomposition behaviour, kinetics and electrical conductivity of the non-isothermal decomposition of pyridine mono carboxylic acids and some of their transition metal complexes

The thesis is divided into four chapters. They are: introduction, experimental, results and discussion about the free ligands and results and discussion about the complexes. The First Chapter, the introductory chapter, is a general introduction to the study of solid state reactions. The Second Chapter is devoted to the materials and experimental methods that have been used for carrying out tile experiments. TIle Third Chapter is concerned with the characterisations of free ligands (Picolinic acid, nicotinic acid, and isonicotinic acid) by using elemental analysis, IR spectra, X-ray diffraction, and mass spectra. Additionally, the thermal behaviour of free ligands in air has been studied by means of thermogravimetry (TG), derivative thermogravimetry (DTG), and differential scanning calorimetry (DSC) measurements. The behaviour of thermal decomposition of the three free ligands was not identical Finally, a computer program has been used for kinetic evaluation of non-isothermal differential scanning calorimetry data according to a composite and single heating rate methods in comparison with the methods due to Ozawa and Kissinger methods. The most probable reaction mechanism for the free ligands was the Avrami-Erofeev equation (A) that described the solid-state nucleation-growth mechanism. The activation parameters of the decomposition reaction for free ligands were calculated and the results of different methods of data analysis were compared and discussed. The Fourth Chapter, the final chapter, deals with the preparation of cobalt, nickel, and copper with mono-pyridine carboxylic acids in aqueous solution. The prepared complexes have been characterised by analyses, IR spectra, X-ray diffraction, magnetic moments, and electronic spectra. The stoichiometry of these compounds was ML2x(H20), (where M = metal ion, L = organic ligand and x = water molecule). The environments of cobalt, nickel, and copper nicotinates and the environments of cobalt and nickel picolinates were octahedral, whereas the environment of copper picolinate [Cu(PA)2] was tetragonal. However, the environments of cobalt, nickel, and copper isonicotinates were polymeric octahedral structures. The morphological changes that occurred throughout the decomposition were followed by SEM observation. TG, DTG, and DSC measurements have studied the thermal behaviour of the prepared complexes in air. During the degradation processes of the hydrated complexes, the crystallisation water molecules were lost in one or two steps. This was also followed by loss of organic ligands and the metal oxides remained. Comparison between the DTG temperatures of the first and second steps of the dehydration suggested that the water of crystallisation was more strongly bonded with anion in Ni(II) complexes than in the complexes of Co(II) and Cu(II). The intermediate products of decomposition were not identified. The most probable reaction mechanism for the prepared complexes was also Avrami-Erofeev equation (A) characteristic of solid-state nucleation-growth mechanism. The tempemture dependence of conductivity using direct current was determined for cobalt, nickel, Cl.nd copper isonicotinates. An activation energy (ΔΕ), the activation energy (ΔΕ ) were calculated.The ternperature and frequency dependence of conductivity, the frequency dependence of dielectric constant, and the dielectric loss for nickel isonicotinate were determined by using altemating current. The value of s paralneter and the value of'density of state [N(Ef)] were calculated. Keyword Thermal decomposition, kinetic, electrical conduclion, pyridine rnono~ carboxylic acid, cOlnplex, transition metal compJex.

Controlled synthesis and processing of a poly(L-lactide-co-ε-caprolactone) copolymer for biomedical use as an absorbable monofilament surgical suture

Poly(L-lactide-co-ε-caprolactone) 75:25% mol, P(LL-co-CL), was synthesized via bulk ring-opening polymerisation (ROP) using a novel tin(II)alkoxide initiator, [Sn(Oct)]2DEG, at 130oC for 48 hrs. The effectiveness of this initiator was compared withthe well-known conventional tin(II) octoateinitiator, Sn(Oct)2. The P(LL-co-CL) copolymersobtained were characterized using a combination of analytical technique including: nuclear magnetic resonance spectroscopy (NMR), differential scanning calorimetry (DSC), thermogravimetry (TG) and gel permeation chromatography (GPC). The P(LL-co-CL) was melt-spun into monofilament fibres of uniform diameter and smooth surface appearance. Modification of the matrix morphology was then built into the as-spun fibresvia a series of controlled off-line annealing and hot-drawing steps. © (2014) Trans Tech Publications, Switzerland.

Avaliação da influência de cinza da casca de arroz em cimentos para poços de petróleo submetidos à injeção de vapor

Reservoirs that present highly viscous oils require methods to aid in their recovery to the surface. The elev ated oil viscosity hinders its flow through porous media and conventional recovery methods have not obtained significant efficiency. As such, the injection of steam into the reservoir through an injection well has been the most widely used method of therma l recovery, for it allows elevated volumes of recovery due to the viscosity reduction of the oil, facilitating the oil’s mobility within the rock formation and consequently into the production well where it will be exploited. On the other hand, the injecti on of vapor not only affects the fluids found in the rock pores, but the entire structure that composes the well where it is injected due to the high temperatures used in the process. This temperature increment is conducted to the cement, found in the annu lus, responsible for the isolation of the well and the well casing. Temperatures above 110 ̊C create new fazes rich in calcium in the cement matrix, resulting in the reduction of its permeability and the consequential phenomenon of mechanical resistance ret rogression. These alterations generate faults in the cement, reducing the well’s hydraulic isolation, creating insecurity in the operations in which the well will be submitted as well as the reduction of its economic life span. As a way of reducing this re trograde effect, this study has the objective of evaluating the incorporation of rice husk ash as a mineral additive substitute of silica flour , commercially utilized as a source of silica to reduce the CaO/SiO 2 ratio in the cement pastes submitted to high temperatures in thermal recovery. Cement pastes were formulated containing 20 and 30% levels of ash, apart from the basic paste (water + cement) and a reference paste (water + cement + 40% silica flour) for comparison purposes. The tests were executed th rough compression resistance tests, X - Ray diffraction (XRD) techniques, thermogravimetry (TG), scanning electron microscopy (SEM) and chemical anal ysis BY X - ray fluorescence (EDS) on the pastes submitted to cure at low temperatures (45 ̊C) for 28 days following a cure at 280 ̊C and a pressure of 2,000 PSI for 3 days, simulating vapor injection. The results obtained show that the paste containing 30% r ice shell ash is satisfactory, obtaining mechanical resistance desired and equivalent to that of the paste containing 40% silica flour, since the products obtained were hydrated with low CaO/SiO 2 ratio, like the Tobermorita and Xonotlita fases, proving its applicability in well subject to vapor injection.

Determinação da energia de ativação e pureza de medicamentos de referência, genérico e similar utilizando técnicas termoanalíticas

In this work, the reference drugs, generic and similar to the active ingredients acetylsalicylic acid, paracetamol, captopril, hydrochlorothiazide and mebendazole were purchased from local pharmacies and studied by thermogravimetry (TG) and Differential Scanning Calorimetry (DSC). Thermal decomposition was assessed to obtain from the Ozawa method the activation energy in inert atmosphere (nitrogen), using three different heating ratios (5, 10 and 20 o C min-1). The pharmaceutical formulation of the AAS reference was the one who presented different from the others (generic and similar) Thermogravimetric profile indicating likely interaction between the active ingredient and excipients. Was observed at the heating rate of the inverse temperature that no linearity of the data, ie, there was no correlation between the percentage of mass loss and the activation energy involved in the thermal decomposition of the pharmaceutical formulation of the AAS reference log graph. The analysis by differential scanning calorimetry was performed in nitrogen atmosphere with a heating rate of 10 ° C min-1. In the analysis of these same drugs, the data curves found on the melting point were, except for hydrochlorothiazide, are consistent with the literature. Hydrochlorothiazide presented a melting point well below that found in the literature, which may be justified due to the interaction of the active ingredient with the excipient lactose. In the study of purity, using the Van't Hoff equation, the reference drugs hydrochlorothiazide and mebendazole reference generic and showed similar impurity content below the limit established that this equation must be greater than 2.5 mol%

Síntese e caracterização de compostos de coordenação do Ácido 4-cloro-2-(2- furilmetilamino)-5- sulfamoil-benzóico com os íons níquel, cobalto e zinco

This work aimed to promote the synthesis, characterization and propose a plausible molecular structure for coordination compounds involving furosemide (4-Chloro-2-(2- furylmethylamino)-5-sulfamoyl-benzoic acid) with the metal ions Ni+2, Zn+2 and Co+2. The compounds were obtained in methanoic medium by evaporation of the solvent after the synthesis procedure. For characterization of coordination compounds determining the levels of metals by EDTA complexometry, infrared spectroscopy (FTIR), solubility of compounds in various solvents, thermogravimetry (TG), differential scanning calorimetry (DSC), differential thermal analysis were made (DTA), determination of the carbon , hydrogen and nitrogen (CHN). The results of infrared spectroscopy in the region suggest that the organic ligand is coordinated in a bidentate fashion to the metal ions, the metal center interactions to occur by the coordination of the nitrogen atom of the amino group and the oxygen atom of the carboxylic acid of the structure of furosemide. With the results of the levels of metal, elemental analysis (CHN) and thermal analysis has been possible to propose the structure of the ligand. The values of the molar conductivity of the complex in acetonitrile behavior suggest the non acetonitrile electrolyte solution. With the solubility tests it was found that the compounds have high solubility in methanol and acetonitrile, as are partially insoluble in water. From the results of thermal analysis (TG, DSC, DTA), it was possible to obtain the thermal behavior of the compounds as stages of dehydration, thermal stability, decomposition and the energies involved.

Novos adsorventes para aplicação na remoção de enxofre de combustíveis

Currently the market requires increasingly pure oil derivatives and, with that, comes the need for new methods for obtaining those products that are more efficient and economically viable. Considering the removal of sulfur from diesel, most refineries uses catalytic hydrogenation process, the hydrodesulfurization. These processes needs high energy content and high cost of production and has low efficiency in removing sulfur at low concentrations (below 500 ppm). The adsorption presents itself as an efficient and economically viable alternative in relation to the techniques currently used. With that, the main purpose of this work is to develop and optimize the obtaining of new adsorbents based on diatomite, modified with two non ionic surfactants microemulsions, adding efficiency to the material, to its application on removal of sulfur present in commercial diesel. Analyses were undertaken of scanning electron microscopy (SEM), x-ray diffraction (XRD), x-ray fluorescence (XRF), thermogravimetry (TG) and N2 adsorption (BET) for characterization of new materials obtained. The variables used for diatomite modification were: microemulsion points for each surfactant (RNX 95 and UNTL 90), microemulsion aqueous phase through the use or non-use of salts (CaCl2 and BaCl2), the contact time during the modification and the contact form. The study of adsorption capacity of materials obtained was performed using a statistical modeling to evaluate the influence of salt concentration in the aqueous phase (20 ppm to 1500 ppm), finite bath temperature (25 to 60° C) and the concentration of sulphur in diesel. It was observed that the temperature and the concentration of sulphur (300 to 1100 ppm) were the most significant parameters, in which increasing their values increase the ability of modified clay to adsorb the sulphur in diesel fuel. Adsorption capacity increased from 0.43 to mg/g 1.34 mg/g with microemulsion point optimization and with the addition of salts.

COMBUSTION and PYROLYSIS of A SLUDGE FROM WASTEWATER TREATMENT PLANT

The possibility of thermal treatment plants of municipal wastewater is an alternative solution for the final disposition of the sludge produced on small cities as Barueri, a small town of São Paulo State, Brazil. Combustion and pyrolysis of that municipal waste, occurring respectively in air and nitrogen, have been studied by thermogravimetry (TG) and differential thermal analysis (DTA). The main steps of each case were analyzed and Kissinger plots were used to estimate respective activation energies. DTG peaks are more indicated to represent the condition of maximum reaction rates than DTA peaks.

Adição de cascalho de perfuração da bacia potiguar em argilas para uso em materiais cerâmicos: influência da concentração e temperatura de queima.

One of waste produced on large scale during the well drilling is the gravel drilling. There are techniques for the treatment of the same, but there isn t consensus on what are the best in terms of economic and environmental. One alternative for disposal of this waste and objective of this paper is the incorporation and immobilization of gravel clay matrix to assess their technological properties. The Raw Materials used were characterized by the following techniques: Chemical Analysis by X-ray fluorescence (XRF), mineralogical analysis by X-ray Diffraction (XRD), Grain Size Analysis (FA) and Thermal Analysis by Thermogravimetry (TG) and thermodiferential (DTA). After characterizing, samples were formulated in the following percentages: 0, 5, 10, 15, 25, 50, 75, 100% (weight) of gravel drilling, then the pieces were pressed, dried (110 ° C) and sintered at temperatures of 850, 950 and 1050 ° C. After sintering, samples were tested for water absorption, linear shrinkage, flexural strength, porosity, density, XRD and test color. The results concluded that the incorporation of gravel drilling is a viable possibility for solid masonry bricks and ceramic blocks manufacture at concentrations and firing temperature described here. Residue incorporation reduces an environmental problem, the cost of raw materials for manufacture of ceramic products

Influência do uso de combustíveis alternativos na síntese por combustão via microondas para a produção de materiais cerâmicos com estrutura espinélio

The development and study of detectors sensitive to flammable combustible and toxic gases at low cost is a crucial technology challenge to enable marketable versions to the market in general. Solid state sensors are attractive for commercial purposes by the strength and lifetime, because it isn t consumed in the reaction with the gas. In parallel, the use of synthesis techniques more viable for the applicability on an industrial scale are more attractive to produce commercial products. In this context ceramics with spinel structure were obtained by microwave-assisted combustion for application to flammable fuel gas detectors. Additionally, alternatives organic-reducers were employed to study the influence of those in the synthesis process and the differences in performance and properties of the powders obtained. The organic- reducers were characterized by Thermogravimetry (TG) and Derivative Thermogravimetry (DTG). After synthesis, the samples were heat treated and characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), analysis by specific area by BET Method and Scanning Electron Microscopy (SEM). Quantification of phases and structural parameters were carried through Rietveld method. The methodology was effective to obtain Ni-Mn mixed oxides. The fuels influenced in obtaining spinel phase and morphology of the samples, however samples calcined at 950 °C there is just the spinel phase in the material regardless of the organic-reducer. Therefore, differences in performance are expected in technological applications when sample equal in phase but with different morphologies are tested