Dynamic Analysis Model of Spherical Roller Bearings with Defects

Rolling element bearings are essential components of rotating machinery. The spherical roller bearing (SRB) is one variant seeing increasing use, because it is self-aligning and can support high loads. It is becoming increasingly important to understand how the SRB responds dynamically under a variety of conditions. This doctoral dissertation introduces a computationally efficient, three-degree-of-freedom, SRB model that was developed to predict the transient dynamic behaviors of a rotor-SRB system. In the model, bearing forces and deflections were calculated as a function of contact deformation and bearing geometry parameters according to nonlinear Hertzian contact theory. The results reveal how some of the more important parameters; such as diametral clearance, the number of rollers, and osculation number; influence ultimate bearing performance. Distributed defects, such as the waviness of the inner and outer ring, and localized defects, such as inner and outer ring defects, are taken into consideration in the proposed model. Simulation results were verified with results obtained by applying the formula for the spherical roller bearing radial deflection and the commercial bearing analysis software. Following model verification, a numerical simulation was carried out successfully for a full rotor-bearing system to demonstrate the application of this newly developed SRB model in a typical real world analysis. Accuracy of the model was verified by comparing measured to predicted behaviors for equivalent systems.

Mechanical simulation of the endovascular repair of abdominal aortic aneurysms

Ce travail de thèse porte sur la simulation du déploiement des prothèses vasculaires de type stent-graft (SG) lors de la réparation endovasculaire (EVAR) des anévrismes de l’aorte abdominale (AAA). Cette étude se présente en trois parties: (i) tests mécaniques en flexion et compression de SG couramment utilisés (corps et jambage de marque Cook) ainsi que la simulation numérique desdits tests, (ii) développement d’un modèle numérique d’anévrisme, (iii) stratégie de simulation du déploiement des SG. La méthode numérique employée est celle des éléments finis. Dans un premier temps, une vérification du modèle éléments finis (MEF) des SG est realisée par comparaison des différents cas de charge avec leur pendant expérimental. Ensuite, le MEF vasculaire (AAA) est lui aussi vérifié lors d’une comparaison des niveaux de contraintes maximales principales dans la paroi avec des valeurs de la littérature. Enfin, le déploiement est abordé tout en intégrant les cathéters. Les tests mécaniques menés sur les SG ont été simulés avec une différence maximale de 5,93%, tout en tenant compte de la pré-charge des stents. Le MEF de la structure vasculaire a montré des contraintes maximales principales éloignées de 4,41% par rapport à un modèle similaire précédemment publié. Quant à la simulation du déploiement, un jeu complet de SG a pu être déployé avec un bon contrôle de la position relative et globale, dans un AAA spécifique pré-déformé, sans toutefois inclure de thrombus intra-luminal (TIL). La paroi du AAA a été modélisée avec une loi de comportement isotropique hyperélastique. Étant donné que la différence maximale tolérée en milieu clinique entre réalité et simulation est de 5%, notre approche semble acceptable et pourrait donner suite à de futurs développements. Cela dit, le petit nombre de SG testés justifie pleinement une vaste campagne de tests mécaniques et simulations supplémentaires à des fins de validation.

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Thermoaktive Bauteilsysteme - Ein neuer simulationstechnischer Berechnungsansatz

Thermoaktive Bauteilsysteme sind Bauteile, die als Teil der Raumumschließungsflächen über ein integriertes Rohrsystem mit einem Heiz- oder Kühlmedium beaufschlagt werden können und so die Beheizung oder Kühlung des Raumes ermöglichen. Die Konstruktionenvielfalt reicht nach diesem Verständnis von Heiz, bzw. Kühldecken über Geschoßtrenndecken mit kern-integrierten Rohren bis hin zu den Fußbodenheizungen. Die darin enthaltenen extrem trägen Systeme werden bewußt eingesetzt, um Energieangebot und Raumenergiebedarf unter dem Aspekt der rationellen Energieanwendung zeitlich zu entkoppeln, z. B. aktive Bauteilkühlung in der Nacht, passive Raumkühlung über das kühle Bauteil am Tage. Gebäude- und Anlagenkonzepte, die träge reagierende thermoaktive Bauteilsysteme vorsehen, setzen im kompetenten und verantwortungsvollen Planungsprozeß den Einsatz moderner Gebäudesimulationswerkzeuge voraus, um fundierte Aussagen über Behaglichkeit und Energiebedarf treffen zu können. Die thermoaktiven Bauteilsysteme werden innerhalb dieser Werkzeuge durch Berechnungskomponenten repräsentiert, die auf mathematisch-physikalischen Modellen basieren und zur Lösung des bauteilimmanenten mehrdimensionalen instationären Wärmeleitungsproblems dienen. Bisher standen hierfür zwei unterschiedliche prinzipielle Vorgehensweisen zur Lösung zur Verfügung, die der physikalischen Modellbildung entstammen und Grenzen bzgl. abbildbarer Geometrie oder Rechengeschwindigkeit setzen. Die vorliegende Arbeit dokumentiert eine neue Herangehensweise, die als experimentelle Modellbildung bezeichnet wird. Über den Weg der Systemidentifikation können aus experimentell ermittelten Datenreihen die Parameter für ein kompaktes Black-Box-Modell bestimmt werden, das das Eingangs-Ausgangsverhalten des zugehörigen beliebig aufgebauten thermoaktiven Bauteils mit hinreichender Genauigkeit widergibt. Die Meßdatenreihen lassen sich über hochgenaue Berechnungen generieren, die auf Grund ihrer Detailtreue für den unmittelbaren Einsatz in der Gebäudesimulation ungeeignet wären. Die Anwendung der Systemidentifikation auf das zweidimensionale Wärmeleitungsproblem und der Nachweis ihrer Eignung wird an Hand von sechs sehr unterschiedlichen Aufbauten thermoaktiver Bauteilsysteme durchgeführt und bestätigt sehr geringe Temperatur- und Energiebilanzfehler. Vergleiche zwischen via Systemidentifikation ermittelten Black-Box-Modellen und physikalischen Modellen für zwei Fußbodenkonstruktionen zeigen, daß erstgenannte auch als Referenz für Genauigkeitsabschätzungen herangezogen werden können. Die Praktikabilität des neuen Modellierungsansatzes wird an Fallstudien demonstriert, die Ganzjahressimulationen unter Bauteil- und Betriebsvariationen an einem exemplarischen Büroraum betreffen. Dazu erfolgt die Integration des Black-Box-Modells in das kommerzielle Gebäude- und Anlagensimulationsprogramm CARNOT. Die akzeptablen Rechenzeiten für ein Einzonen-Gebäudemodell in Verbindung mit den hohen Genauigkeiten bescheinigen die Eignung der neuen Modellierungsweise.

Transport of Sub-micron Aerosols in Bifurcations

The convective-diffusive transport of sub-micron aerosols in an oscillatory laminar flow within a 2-D single bifurcation is studied, using order-of-magnitude analysis and numerical simulation using a commercial software (FEMLAB®). Based on the similarity between momentum and mass transfer equations, various transient mass transport regimes are classified and scaled according to Strouhal and beta numbers. Results show that the mass transfer rate is highest at the carinal ridge and there is a phase-shift in diffusive transport time if the beta number is greater than one. It is also shown that diffusive mass transfer becomes independent of the oscillating outer flow if the Strouhal number is greater than one.

Assessment of virtual design and manufacturing techniques for fibre reinforced composite materials

Virtual tools are commonly used nowadays to optimize product design and manufacturing process of fibre reinforced composite materials. The present work focuses on two areas of interest to forecast the part performance and the production process particularities. The first part proposes a multi-physical optimization tool to support the concept stage of a composite part. The strategy is based on the strategic handling of information and, through a single control parameter, is able to evaluate the effects of design variations throughout all these steps in parallel. The second part targets the resin infusion process and the impact of thermal effects. The numerical and experimental approach allowed the identificationof improvement opportunities regarding the implementation of algorithms in commercially available simulation software.

Urban microclimates and simulation

This chapter examines the workings of urban microclimates and looks at the associated causes and effects of the urban heat island (UHI). It also clarifies the relationship between urban form and the key climatic parameters (sun, daylight, wind, temperature). A particular section is devoted to the concepts of UHI intensity and sky view factor (SVF); these are useful indicators for researchers in this area. The challenge of how to model urban microclimates is covered, featuring the six archetypal urban forms familiar to analysts involved in using simulation software. The latter sections address the issue of urban thermal comfort, the importance of urban ventilation and finally what mitigating strategies can be implemented to curb negative UHI effects.

Simulation of thermal performance of horizontal slinky-loop heat exchangers for ground source heat pumps

This paper presents results obtained from a numerical simulation for the horizontal slinky-loop heat exchanger of a ground-source heat pump system. A three-dimensional numerical model was developed and the results of the thermal performance of various heat exchanger configurations are presented. The investigation was carried out on five types of loop pitch (loop spacing), three types of loop diameter, three values of soil thermal properties, and allowing continuous and intermittent operation. Comparison was made for the heat transfer rate, the amount of pipe material needed, as well as excavation work required for the horizontal slinky-loop heat exchanger. The results indicate that system parameters have a significant effect on the thermal performance of the system

The role of convective parameterization in the simulation of a cyclone over the South Atlantic

Numerical simulations are carried out to examine the role of the Kuo and Kain-Fritsch (KF) cumulus parameterization schemes and dry dynamics on a cyclone development, in a weak baroclinic atmosphere, over subtropical South Atlantic Ocean. The initial phase of the cyclone development is investigated with a coarse horizontal mesh (75 km) and when the cyclone reaches the mature stage two different horizontal resolutions are used (75 and 25 km). The best performance simulation for the cyclone initial phase occurs when the Kuo convective scheme is applied, and this may be attributed to a greater diabatic warming in the troposphere. On the other hand, the dry simulation is not capable of simulating the correct location and intensity of the cyclone in its initial phase. During the mature phase, a cyclone over deepening occurs in the Kuo scheme experiment associated with larger latent heat release in a deep vertical column. The presence of downdraft currents in the KF scheme, which acts to cool and dry the lower levels, is essential to stabilize the atmosphere and to reproduce the nearest observation cyclone deepening rate. The largest cyclone deepening is found in the Kuo scheme high resolution experiment. This suggests that the KF convective scheme is less sensitive to the horizontal grid resolution. It was also revealed that the diabatic processes are crucial to simulate the observed features of this marine cyclone over subtropical region.

Generating Segmented Quality Meshes from Images

Techniques devoted to generating triangular meshes from intensity images either take as input a segmented image or generate a mesh without distinguishing individual structures contained in the image. These facts may cause difficulties in using such techniques in some applications, such as numerical simulations. In this work we reformulate a previously developed technique for mesh generation from intensity images called Imesh. This reformulation makes Imesh more versatile due to an unified framework that allows an easy change of refinement metric, rendering it effective for constructing meshes for applications with varied requirements, such as numerical simulation and image modeling. Furthermore, a deeper study about the point insertion problem and the development of geometrical criterion for segmentation is also reported in this paper. Meshes with theoretical guarantee of quality can also be obtained for each individual image structure as a post-processing step, a characteristic not usually found in other methods. The tests demonstrate the flexibility and the effectiveness of the approach.

Numerical prediction of three-dimensional time-dependent viscoelastic extrudate swell using differential and algebraic models

This study investigates the numerical simulation of three-dimensional time-dependent viscoelastic free surface flows using the Upper-Convected Maxwell (UCM) constitutive equation and an algebraic explicit model. This investigation was carried out to develop a simplified approach that can be applied to the extrudate swell problem. The relevant physics of this flow phenomenon is discussed in the paper and an algebraic model to predict the extrudate swell problem is presented. It is based on an explicit algebraic representation of the non-Newtonian extra-stress through a kinematic tensor formed with the scaled dyadic product of the velocity field. The elasticity of the fluid is governed by a single transport equation for a scalar quantity which has dimension of strain rate. Mass and momentum conservations, and the constitutive equation (UCM and algebraic model) were solved by a three-dimensional time-dependent finite difference method. The free surface of the fluid was modeled using a marker-and-cell approach. The algebraic model was validated by comparing the numerical predictions with analytic solutions for pipe flow. In comparison with the classical UCM model, one advantage of this approach is that computational workload is substantially reduced: the UCM model employs six differential equations while the algebraic model uses only one. The results showed stable flows with very large extrudate growths beyond those usually obtained with standard differential viscoelastic models. (C) 2010 Elsevier Ltd. All rights reserved.

Evaluation of a bounded high order upwind scheme for 3D incompressible free surface flow computations

fit the context of normalized variable formulation (NVF) of Leonard and total variation diminishing (TVD) constraints of Harten. this paper presents an extension of it previous work by the authors for solving unsteady incompressible flow problems. The main contributions of the paper are threefold. First, it presents the results of the development and implementation of a bounded high order upwind adaptative QUICKEST scheme in the 3D robust code (Freeflow), for the numerical solution of the full incompressible Navier-Stokes equations. Second, it reports numerical simulation results for 1D hock tube problem, 2D impinging jet and 2D/3D broken clam flows. Furthermore, these results are compared with existing analytical and experimental data. And third, it presents the application of the numerical method for solving 3D free surface flow problems. (C) 2007 IMACS. Published by Elsevier B.V. All rights reserved,

Estudo do comportamento de um solo mole tratado com cal, visando seu uso em fundações superficiais

Neste trabalho foi analisada a melhoria nas características de um solo mole quando tratado com cal, bem como a viabilidade técnica de se utilizar este novo material como uma camada suporte de fundações superficiais. O solo estudado classifica-se pedologicamente como Gley Húmico e a jazida localiza-se no município de Canoas/RS, às margens da BR 386. O trabalho teve as seguintes finalidades: realizar um estudo da influência dos diferentes teores de cal sobre as características tensão x deformação do solo tratado; verificar o ganho de resistência com o tempo de cura; modelar o comportamerito tensão x deformação do material tratado; realizar simulações numéricas, através do Método dos Elementos Finitos, do comportamento carga x recalque de fundações continuas flexíveis assentes sobre o novo material. Adotou-se o teor ótimo de cal (obtido pelo método de Eades & Grim, 1966) de 9% e dois valores inferiores de 7% e 5%. Realizaram-se os seguintes ensaios sobre o solo natural e as misturas de solo-cal: limites de Atterberg, compactação, granulometria, difratograma de raio X, permeabilidade (triaxial) e ensaios triaxiais adensados não drenados(CIU). Todos os ensaios foram realizados para três tempos de cura (7, 28 e 90 dias) e os corpos de prova foram curados em câmara úmida. Para modelar o comportamento tensão x deformação do solo melhorado, adotou-se o Modelo Hiperbólico e para o solo natural o Modelo Cam-Clay Modificado. O Modelo Hiperbólico foi implementado no software CRISPSO, desenvolvido na Universidade de Cambridge, Inglaterra. O software foi utilizado em um estudo paramétrico para determinar a influência do processo de estabilização no comportamento carga x recalque de fundações superficiais. Dos resultados obtidos, concluiu-se: que o método de Eades & Grim (1966) não mostrou-se adequado para determinação do teor ótimo de cal; houve, de maneira geral, melhora nas características físicas com o tratamento com cal; não houve ganho de resistência com o tempo de cura; o modelo hiperbólico representou bem o comportamento das misturas de solo cal e a colocação de uma camada de solo tratado apresenta melhoras no comportamento carga x recalque de fundações superficiais contínuas flexíveis.

Estudo comparativo de pás para aerogeradores de grande porte fabricadas em materiais compósitos reforçadas com fibra de carbono ou fibra de vidro

The research and development of wind turbine blades are essential to keep pace with worldwide growth in the renewable energy sector. Although currently blades are typically produced using glass fiber reinforced composite materials, the tendency for larger size blades, particularly for offshore applications, has increased the interest on carbon fiber reinforced composites because of the potential for increased stiffness and weight reduction. In this study a model of blade designed for large generators (5 MW) was studied on a small scale. A numerical simulation was performed to determine the aerodynamic loading using a Computational Fluid Dynamics (CFD) software. Two blades were then designed and manufactured using epoxy matrix composites: one reinforced with glass fibers and the other with carbon fibers. For the structural calculations, maximum stress failure criterion was adopted. The blades were manufactured by Vacuum Assisted Resin Transfer Molding (VARTM), typical for this type of component. A weight comparison of the two blades was performed and the weight of the carbon fiber blade was approximately 45% of the weight of the fiberglass reinforced blade. Static bending tests were carried out on the blades for various percentages of the design load and deflections measurements were compared with the values obtained from finite element simulations. A good agreement was observed between the measured and calculated deflections. In summary, the results of this study confirm that the low density combined with high mechanical properties of carbon fibers are particularly attractive for the production of large size wind turbine blades

Estudo de sistemas multicomponentes no processo de injeção cíclica de vapor

In Brazilian Northeast there are reservoirs with heavy oil, which use steam flooding as a recovery method. This process allows to reduce oil viscosity, increasing its mobility and consequently its oil recovery. Steam injection is a thermal method and can occurs in continues or cyclic form. Cyclic steam stimulation (CSS) can be repeated several times. Each cycle consisting of three stages: steam injection, soaking time and production phase. CSS becomes less efficient with an increase of number of cycles. Thus, this work aims to study the influence of compositional models in cyclic steam injection and the effects of some parameters, such like: flow injection, steam quality and temperature of steam injected, analyzing the influence of pseudocomponents numbers on oil rate, cumulative oil, oil recovery and simulation time. In the situations analyzed was compared the model of fluid of three phases and three components known as Blackoil . Simulations were done using commercial software (CMG), it was analyzed a homogeneous reservoir with characteristics similar to those found in Brazilian Northeast. It was observed that an increase of components number, increase the time spent in simulation. As for analyzed parameters, it appears that the steam rate, and steam quality has influence on cumulative oil and oil recovery. The number of components did not a lot influenced on oil recovery, however it has influenced on gas production