Effect of urea and glycine fuels on the combustion reaction synthesis of Mn-Zn ferrites: Evaluation of morphology and magnetic properties

The goal of this study is to evaluate the influence of the urea and glycine fuels on the synthesis of Mn-Zn ferrite by combustion reaction The morphology and magnetic properties of the resulting powders were investigated. The powders were characterized by X-ray diffraction (XRD), nitrogen adsorption (BET), scanning and transmission electron microscopy (SEM and TEM), and magnetic measurement of M x H curves. The X-lay diffraction patterns indicated that the samples containing urea resulted in the formation of crystalline powders and the presence of hematite as a secondary phase The samples containing glycine presented only the formation of crystalline and monophases (Mn,Zn)Fe(2)O(4). The average crystallite size was 18 and 35 nm and saturation magnetization was 3.6 and 75 emu/g, respectively, for the samples containing urea and glycine. The samples synthesized with glycine fuel showed better magnetic properties for application as soft magnetic devices. (C) 2009 Elsevier B.V All rights reserved

Influence of calcination temperature on the morphology and magnetic properties of Ni-Zn ferrite applied as an electromagnetic energy absorber

An evaluation was made of the influence of calcination temperatures on the structure, morphology and eletromagnetic properties of Ni-Zn ferrite powders. To this end, Ni(0.5)Zn(0.5)Fe(2)O(4) ferrite powders were prepared by combustion reaction and calcined at temperatures of 800, 1000 and 1200 degrees C/2 h. The resulting powders were characterized by XRD, SEM and reflectivity measurements in the frequency bands of 8-12 GHz. The results demonstrated that raising the calcination temperature increased the particle sizes of the powders of all the systems in question, improving the reflectivity of the materials. (C) 2008 Elsevier B.V. All rights reserved.

Luminescence studies on nitride quaternary alloys double quantum wells

We present theoretical photoluminescence (PL) spectra of undoped and p-doped Al(x)In(1-xy)Ga(y)N/Al(X)In(1) (X) (Y)Ga(Y)N double quantum wells (DQWs). The calculations were performed within the k.p method by means of solving a full eight-band Kane Hamiltonian together with the Poisson equation in a plane wave representation, including exchange-correlation effects within the local density approximation. Strain effects due to the lattice mismatch are also taken into account. We show the calculated PL spectra, analyzing the blue and red-shifts in energy as one varies the spike and the well widths, as well as the acceptor doping concentration. We found a transition between a regime of isolated quantum wells and that of interacting DQWs. Since there are few studies of optical properties of quantum wells based on nitride quaternary alloys, the results reported here will provide guidelines for the interpretation of forthcoming experiments. (C) 2008 Elsevier B.V. All rights reserved.

Structural and electrochemical characteristics of Mg((55-x))Ti(x)Ni((45-y))Pt(y) metal hydride electrodes

In recent years, Mg-Ni-based metastable alloys have been attracting attention due to their large hydrogen sorption capacities, low weight, low cost, and high availability. Despite the large discharge capacity and high activity of these alloys, the accelerated degradation of the discharge capacity after only few cycles of charge and discharge is the main shortcoming against their commercial use in batteries. The addition of alloying elements showed to be an effective way of improving the electrode performance of Mg-Ni-based alloys. In the present work, the effect of Ti and Pt alloying elements on the structure and electrode performance of a binary Mg-Ni alloy was investigated. The XRD and HRTEM revealed that all the investigated alloy compositions had multi-phase nanostructures, with crystallite size in the range of 6 nm. Moreover, the investigated alloying elements demonstrated remarkable improvements of both maximum discharge capacity and cycling life. Simultaneous addition of Ti and Pd demonstrated a synergetic effect on the electrochemical properties of the alloy electrodes. Among the investigated alloys, the best electrochemical performance was obtained for the Mg(51)Ti(4)Ni(43)Pt(2) composition (in at.%), which achieved 448 mAh g(-1) of maximum discharge capacity and retained almost 66% of this capacity after 10 cycles. In contrast, the binary Mg(55)Ni(45) alloy achieved only 248 mAh g(-1) and retained 11% of this capacity after 10 cycles. (C) 2010 Elsevier By. All rights reserved.

Oxygen diffusion in Ti-10Mo alloys measured by mechanical spectroscopy

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influencia de la refusion en las propiedades mecanicas y composicion quimica de aleaciones odontologicas

The objective of the study presented in this article was to analyze the influence of remelting of two odontological alloys: Dentorium and Steeldent, on the mechanical properties and on the chemical composition. For the two alloys, samples, containing 10% and 50% new alloy, were subjected to tensile test, micrography and chemical analysis. The alloys presented similar mechanical properties, except for the elongation, which presented higher values for the Dentorium 50% new alloy. This is due to the smaller carbides formed in this sample. The remelting itself seems not to be responsible for these differences, but they are probably due to the lack of a good control of the casting process. The micrography showed a dendritic column matrix, with carbides in the interdentric region and inside dendritic grain. In the chemical composition was observed few elements percentage change.

Influence of convergence angle of tooth preparation on the fracture resistance of Y-TZP-based all-ceramic restorations

Objective: To investigate the influence of the convergence angle of tooth preparation on the fracture load of Y-TZP-based ceramic (YZ-Vita YZ) substructure (SB) veneered with a feldspathic porcelain (VM9-Vita VM9). Methods: Finite element stress analysis (FEA) was performed to examine the stress distribution of the system. Eighty YZ SB were fabricated using a CAD-CAM system and divided into four groups (n = 20), according to the total occlusal convergence (TOC) angle: G6-6° TOC; G12-12° TOC; G20-20° TOC; and G20MOD-20° TOC with modified SB. All SB were veneered with VM9, cemented in a fiber reinforced epoxy resin die, and loaded to failure. Half of the specimens from each group (n = 10) were cyclic fatigued (106 cycles) before testing. Failure analysis was performed to determine the fracture origin. Data were statistically analyzed using Anova and Tukey's tests (α = 0.05). Results: The greatest mean load to fracture value was found for the G20MOD, which was predicted by the FEA. Cyclic fatigue did not significantly affect the load of fracture. Catastrophic failure originating from the internal occlusal surface of the SB was the predominant failure mode, except for G20MOD. Significance: The YZ-VM9 restorations resisted greater compression load than the usual physiological occlusal load, regardless of the TOC angle of preparations. Yet, the G20MOD design produced the best performance among the experimental conditions evaluated. © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Influence of current density on crystalline structure and magnetic properties of electrodeposited Co-rich CoNiW alloys

The influence of current density, at the interval 5-100 mA cm-2, on the structural and magnetic properties of electrodeposited (Co 100-xNix)100-yWy alloys (x = 23-33.5 at. % Ni, y = 1.7-7.3 at. % W) was studied from a glycine-containing bath. W-content decreases with the increase of the current density magnitude. X-ray data have shown stabilization of hexagonal close packed, face centered cubic or a mixture of these structures by modulating the applied cathodic current density, for values lower than 50 mA cm-2. Two structural phase transitions were observed: one from hexagonal close packed to face centered cubic structural transition occurring for a current density of 20 mA cm -2, and another one, from cubic crystalline phase to amorphous state, which happens for values higher than 50 mA cm-2. These structural phase transitions seem to be associated with the W-content as well as average crystalline grain sizes that reduce with increasing the current density value. The grain size effect may explain the face centered cubic stabilization in Co-rich CoNiW alloys, which was initially assumed to be basically due to H-adsorption/incorporation. Magnetic properties of Co-rich CoNiW alloys are strongly modified by the current density value; as a result of the changes on the W-content and their structural properties© 2013 Elsevier B.V. All rights reserved.

Formas de aplicación de zinc para las plantas de maíz que crecen en Oxisol: Efectos sobre el suelo, la nutrición de las plantas y la productividad

The way of applying zinc can influence the zinc uptake and productivity of crops, especially cereals that have high demand for this nutrient. The aim of this study is to evaluate methods of Zn application on soil, nutritional status and productivity of maize. For this, an experiment was undertaken at FCAV/UNESP, Jaboticabal-SP, in Oxisol clay (DTPA on Zn: 0.5 mg dm-3) with maize (hybrid Simple Impact), from December through May 2009. Nine treatments with three doses of Zn in soil banded application (in furrows) and three doses of Zn by incorporation in soil (0-20 cm depth), foliar application, seed application and control (no Zn). The treatments were arranged in a randomized block design with four replications. Regardless of the method, Zn application promoted higher contents of this micronutrient in soil and higher accumulation in the shoots as well as increasing Zn in the maize grain. However, it did not affect the nutritional status and yield of the maize. The Zn application in the soil resulted in a greater Zn uptake by plants and maize yield, compared to Zn application in the plant by seed or foliar.

Aplicación de un subproducto del procesamiento de guayaba en un Ultisol, en presencia y en ausencia de fertilización mineral

There is a relative lack of technical studies on the adequate management of organic wastes from food processing. The aim of this study was to evaluate the effect of applying doses of a byproduct from guava processing, in the presence and absence of mineral fertilization, on the fertility of a an Ultisol (or Red-Yellow Argisol) under laboratory conditions. An entirely randomized 5x2 factorial experimental design was used with five byproduct doses, in the presence and absence of mineral fertilization, with four repetitions, for a total of 40 experimental units. Under the experimental conditions, the attributes pH, OM, K, Mg, BS, T, V, B, Fe, Zn and S-SO42- were affected by the guava byproduct doses, as well as by the presence or absence of mineral fertilization. With the use of this fertilization, the variables OM, K, H+Al, T, Fe and Zn increased more as a function of byproduct dose than in the absence of fertilization. The results obtained demonstrate the potential of using this waste material in the cycling and supply of nutrients.

Analiticidade e efeito gráfico da dilatação em funções octoniônicos quaseconformes do tipo F(Z)=Zn

Pós-graduação em Matemática - IBILCE

Structural, morphological and magnetic characterization of electrodeposited Co-Fe-W alloys

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Corrosion properties of Fe-Cr-Nb-B amorphous alloys and coatings

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Distribución espacial de metales pesados y As en sedimentos superficiales de fondo del estuario del Río de la Plata

Los sedimentos estuarinos actúan como sumidero dediversos tipos de contaminantes, por lo que son utilizados como indicadores del impacto antropogénico. Entre estos aportes, los metales se destacan debido a que pueden generar efectos tóxicos y/o letales para la biota. Además son bioacumulables y se biomagnifican a través de la trama trófica acuática. El estuario del Río de la Plata (RdlP) constituye un área de desove y cría de peces y otros organismos de interés comercial, por lo que resulta relevante conocer la contaminación metálica. El RdlP tiene una superficie de 38.800 km2 y un caudal promedio de 24.045 m3s-1, siendo sus principales afluente los Ríos Paraná y Uruguay. El presente estudio analizó muestras de sedimento superficial de fondo, colectado en 26 sitios (año 2010). Se cuantificó el contenido de Al, As, Cd, Cr, Cu, Fe, Ni, Pb, Sc y Zn, a través del método USEPA 3050b y la técnica analítica ICP-OES. La exactitud y la precisión del método fueron evaluadas por material de referencia certificado. La granulometría del sedimento estudiado indicó la predominancia de sedimentos finos (limos y arcillas), en sitios con mayores contenidos metálicos. Las concentraciones obtenidas se compararon con los valores guía del Criteria for the Assessment of Sediment Quality in Quebec and Application Frameworks (de Canadá), utilizados como criterio de evaluación para legislación ambiental: TEL (threshold effect level) y PEL (probable effect level); además se utilizaron los niveles REL (rare effect level), OEL (occasional effect level) y FEL (frequent effect level). La concentración de As y Cu fue mayor al nivel TEL en varios sitios analizados (7,2 y 19 mg/kg respectivamente). Para ningún elemento la concentración fue mayor que el PEL. Este criterio de evaluación constituye una herramienta válida para el monitoreo de la contaminación de los sedimentos del estuario, indicando posibles efectos negativos sobre la biota del RdlP