Systematic methodology for the design of high performance recursive digital filters

A systematic design methodology is described for the rapid derivation of VLSI architectures for implementing high performance recursive digital filters, particularly ones based on most significant digit (msd) first arithmetic. The method has been derived by undertaking theoretical investigations of msd first multiply-accumulate algorithms and by deriving important relationships governing the dependencies between circuit latency, levels of pipe-lining and the range and number representations of filter operands. The techniques described are general and can be applied to both bit parallel and bit serial circuits, including those based on on-line arithmetic. The method is illustrated by applying it to the design of a number of highly pipelined bit parallel IIR and wave digital filter circuits. It is shown that established architectures, which were previously designed using heuristic techniques, can be derived directly from the equations described.

3D Analysis of Seepage under Hydraulic Structures with Intermediate Filters

Seepage flow under hydraulic structures provided with intermediate filters has been investigated. The flow through the banks of the canal has been included in the model. Different combinations of intermediate filter and canal width were studied. Different lengths of the floor, differential heads, and depths of the sheet pile driven beneath the floor were also investigated. The introduction of an intermediate filter to the floor of hydraulic structures reduced the uplift force acting on the downstream floor by up to 72%. The maximum uplift reduction occurred when the ratio of the distance of filter location downstream from the cutoff to the differential head was 1. Introducing a second filter in the downstream side resulted in a further reduction in the exit hydraulic gradient and in the uplift force, which reached 90%. The optimum locations of the two filters occurred when the first filter was placed just downstream of the cutoff wall and the second filter was placed nearly at the middistance between the cutoff and the end toe of the floor. The results showed significant differences between the three-dimensional (3D) and the two-dimensional (2D) analyses.

Holistic Design Strategy for High-Selectivity Low-Loss Integrated Millimetre-Wave Image-Reject Filters

To alleviate practical limitations in the design of mm-wave on-chip image-reject filters, systematic design methodologies are presented. Three low-order filters with high-selectivity and low-loss characteristics are designed and compared. Transmission zeroes are created by means of a quarter-wave transmission line (filter 1) and a series LC resonator (filters 2 and 3). Implemented on SiGe, the filters occupy 0.125, 0.064, and 0.079 mm2 chip area including pads. The measured transmission
losses across 81-86 GHz E-Band frequency range are 3.6-5.2 dB for filter 1, 3.1-4.7 dB for filter 2 and 3.6-5 dB for filter 3 where rejection levels at the image band are greater than 30 dB.

Search filters: mapping the literature using a novel form of content analysis.

Background: Search filters are combinations of words and phrases designed to retrieve an optimal set of records on a particular topic (subject filters) or study design (methodological filters). Information specialists are increasingly turning to reusable filters to focus their searches. However, the extent of the academic literature on search filters is unknown. We provide a broad overview to the academic literature on search filters.
Objectives: To map the academic literature on search filters from 2004 to 2015 using a novel form of content analysis.
Methods: We conducted a comprehensive search for literature between 2004 and 2015 across eight databases using a subjectively derived search strategy. We identified key words from titles, grouped them into categories, and examined their frequency and co-occurrences.
Results: The majority of records were housed in Embase (n = 178) and MEDLINE (n = 154). Over the last decade, both databases appeared to exhibit a bimodal distribution with the number of publications on search filters rising until 2006, before dipping in 2007, and steadily increasing until 2012. Few articles appeared in social science databases over the same time frame (e.g. Social Services Abstracts, n = 3).
Unsurprisingly, the term ‘search’ appeared in most titles, and quite often, was used as a noun adjunct for the word 'filter' and ‘strategy’. Across the papers, the purpose of searches as a means of 'identifying' information and gathering ‘evidence’ from 'databases' emerged quite strongly. Other terms relating to the methodological assessment of search filters, such as precision and validation, also appeared albeit less frequently.
Conclusions: Our findings show surprising commonality across the papers with regard to the literature on search filters. Much of the literature seems to be focused on developing search filters to identify and retrieve information, as opposed to testing or validating such filters. Furthermore, the literature is mostly housed in health-related databases, namely MEDLINE, CINAHL, and Embase, implying that it is medically driven. Relatively few papers focus on the use of search filters in the social sciences.

Simple brightness models with low-pass and Gabor filters

A syntactical brightness model based on a multiscale line and edge representation obtained by a set of anisotropic Gabor filters is quite complex (du Buf and Fischer, 1995 Optical Engineering 34 1900-1911). Although only tested in 1-D, it was shown to yield correct brightness effects for many patterns.

Application of fractional delay filters to tune the centre frequency location of single-band sigma-delta modulators

This paper presents a novel technique for the design of narrow-band sigma-delta modulators with an embedded tunable centre frequency mechanism. This method demonstrates that the use of sum filters combined with a fractional delayer provide the flexibility of tuning the noise shaping band for any desired variable centre frequency input signal.

Increasing the variability of centre frequency locations in multiple-band sigma-delta modulators via the use of fractional delay filters

This paper presents the design analysis of novel tunable narrow-band bandpass sigma-delta modulators, that can achieve concurrent multiple noise-shaping for multi-tone input signals. This approach utilises conventional comb filters in conjunction with FIR, or allpass IIR fractional delay filters, to deliver the desired nulls for the quantisation noise transfer function. Detailed simulation results show that FIR fractional delay comb filter based sigma-delta modulators tune accurately to most centre frequencies, but suffer from degraded resolution at frequencies close to Nyquist. However, superior accuracies are obtained from their allpass IIR fractional delay counterpart at the expense of a slight shift in noise-shaping bands at very high frequencies.

Optically reconfigurable CPW filters for UWB applications

A miniature optically reconfigurable ultra-wideband CPW bandpass filter is proposed. With the optical switch in the ON state (200W), the circuit behaves as a bandpass filter while in the OFF state (0W), the circuit behaves as a bandstop filter within the same frequency band. The simulation results of the proposed bandpass/bandstop filter are presented.

Compact dielectric-filled waveguide filters and diplexers

This paper presents electromagnetic simulations of dielectric-filled rectangular waveguide bandpass filter structures with microstrip to waveguide transitions as well as a diplexer based on such filters for modern wireless systems. The two bandpass filters have been designed and simulated at centre frequencies of 11.85 and 14.25 GHz, respectively. A significant size reduction is achieved through dielectric filling.

Compact high linearity switchable dual-mode microstrip bandpass filters

A compact highly linear microstrip dual-mode electronically switchable filter is presented. The key characteristics of the dual-mode switchable filter are investigated and described. A second order filter design procedure is outlined to facilitate the realisation of Butterworth and Chebyshev functions. The proposed filter was built and tested with NXP pin diode model BAP65-03. The measured and simulated results are in good agreement. The measured insertion loss in the ON state was 3.0 dB the isolation in the OFF state was 45 dB at the centre frequency. An evaluation of filter distortion is presented for digitally modulated 16 QAM and QPSK signals.

Compact filters using metal-dielectric inserts

A novel filter based on e-plane metal-dielectric insert in rectangular waveguide is proposed. Properties of the structure containing metallic septa, C- and I-shaped resonators placed in waveguide are investigated. Pseudo-elliptic cross-coupled filter with direct source-load coupling is designed, simulated and fabricated. Experimental results are presented to prove feasibility of the filter. Significant size reduction is achieved.